Martec IMPERIAL SERIES User manual

IMPERIAL
SERIES
Ceiling Fan Instrucon Book
Models: MIF123 MIF1233 MIF1234 MIF124 MIF1243 MIF1244
DESCRIPTION QUANTITY
Motor assembly 1
Instrucon manual 1
Screw kit 1
Balancing kit 1
Hanging bracket 1
Wall control kit 1
Blades 3 or 4
Cover 1 (for without light)
Light plate 1
Glass shade 1

www.martecaustralia.com.au | 02 8778 7500 | [email protected]om.au
Page 2
IMPORTANT
Always operate the product from a power source of the same Voltage, Frequency and rang
as on the product Idencaon Plate.
IMPORTANT
The fan is to be installed so that the blades are more than 2.1 metres above the oor.
Avoid contacng moving parts, keep hands, hair and clothing well away from the product while it is in
operaon.
A Luminaire (light ng) included in the fan packaging may only be ed to this fan.
“This appliance is not intended for use by persons (including children) with reduced physical, sensory
or mental capabilies, or lack of experience or knowledge, unless they have been given supervision or
instrucon concerning use of the appliance by a person responsible for their safety.”
“Young children should be supervised at all mes to ensure that they do not play with the appliance.”
Do not operate any product which has been or appears damaged in any maer or aer the product
malfuncons.
Do not use the product for other than its intended use as described in these instrucons. This product
is intended for normal domesc household use only. The use of accessory aachments other than those
recommended by the manufacturer may cause safety hazards.
SAFETY
The installaon of fans must follow S.A.A. standards and meet local Authority regulaons. A fully qualied
and licensed electrician lawfully MUST carry out installaon. Means for disconnecon must be incorporated
in the xed wiring in accordance with wiring rules. Fan and light MUST be earthed. Bracket MUST be rmly
aached to a solid structure i.e. concrete ceiling, steel structure or mber frame and addional joist MUST
be nailed between beams if the mber opon is required. ONLY install the remote controller kit that comes
supplied by Martec Pty Ltd within package. DO NOT control operaon of fan and light with any other
remote control than what was approved by Martec Pty Ltd and supplied within this package, as this will void
warranty.
WARNING
Only approved Martec Pty Ltd wall controllers should be used for the operaon of our fans. The use of
unauthorised controllers will void the warranty. DO NOT mix blades from one fan to another. All blades
must be replaced if damaged.
Thank you for purchasing your MARTEC IMPERIAL Series Ceiling Fan. Please read all instrucons carefully
before assembly and use.
IMPORTANT SAFEGUARDS
READ THESE INSTRUCTIONS CAREFULLY BEFORE INSTALLING OR USING THE PRODUCT. KEEP
THE INSTRUCTIONS HANDY FOR FUTURE REFERENCE.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT INSTALL THE PRODUCT WHERE IT
CAN BE EXPOSED TO RAIN, MOISTURE OR ANY LIQUID.

www.martecaustralia.com.au | 02 8778 7500 | [email protected]om.au
Page 3
Hanging bracket
Canopy
Jam Screw
Wall control
Hanging ball joint
Down rod
Cover
Cover
Liqht kit plate
LED / 2 x E27
Glass shade
Without Light With Light
Housing
Blade

www.martecaustralia.com.au | 02 8778 7500 | [email protected]om.au
Page 4
HOW TO INSTALL BLADES
The blade hole posion is aligned with the turntable hole posion. Tighten with the blade screw of the screw
bag. (See Fig.1)
Fig.3Fig.2
Fig.1
HOW TO ASSEMBLE
Secure the hanger bracket to ceiling beam or a suitable piece of mber inserted between the ceiling beams.
Martec Pty Ltd recommends the bracket to be aached with two long screws as supplied within the package.
There is a ball seat rubber cover need to be pressed into the bracket.(See Fig.2)
Place circular shockproof gasket above the hanger bracket.Align the bracket and screw the hanger bracket to
the ceiling ghtly.(See Fig.3)
Place fan into hanger bracket and align Ball Joint Slot with hanger bracket as illustrated. (See Fig.4)
Aer wiring is completed, aach the canopy to the hanger bracket by pushing upwards and twisng
anclockwise. Locate screws in keyholes and ghten, ensuring canopy is not touching the ball joint. (See
Fig.5)
Fig.4 Fig.5

www.martecaustralia.com.au | 02 8778 7500 | [email protected]om.au
Page 5
HOW TO INSTALL THE LIGHT KIT PLATE (Version with light)
The screw on the connecng disk is aligned with the keyhole of the lamp disk.
Aer rotang clockwise to the boom, ghten the screw with the screwdriver to ensure that the screw does
not move
HOW TO INSTALL THE FACE PLATE (Version without light)
The raised clamping posion on the cover is aligned with the slot in the cover and then rotate the cover
clockwise unl it is ghtened
Light Kit Plate Connector
Light Kit Plate
Decoraon Cover

www.martecaustralia.com.au | 02 8778 7500 | [email protected]om.au
Page 6
3000k
4000k
5000k
HOW TO INSTALL THE SHADE (Version with light)
Turn the glass gently clockwise unl it is not loose.
For MIF1234 and MIF1244 models,pls install two E27 13W
Max bulbs before install the glass shade.
CCT (Colour changeable temperature)
Please make sure the switch is o before changing the colour temperature.Simply ick
LED plate (See Fig.7.) to select the desired colour temperature (3000K, 4000K or 5000K).
Dimming
The Imperial fan has a smart 3 step dimming LED light
module which doesn’t require a dimmable remote control
or a wall dimmer. It only requires a normal on/o remote kit
(MPREM) or a normal light wall switch (supplied
as part of the wall controller in the box).
Turn the switch on and the light will turn on.Flick the switch
on/o within 1 second and the light output
will dim down to approx.50%,ick the switch on/o again
and the light output will down to approximately 15%.
The light kit has no memory funcon, it will turn on at 100%
inially.
Fig.7
Fig.6

www.martecaustralia.com.au | 02 8778 7500 | [email protected]om.au
Page 7