Martec Malibu Series User manual

E: [email protected] | P: 02 8778 7500
www.martecaustralia.com.au
MALIBU Series Installation Guide
Thanks for choosing our Malibu Series ceiling fan.
We strongly recommend that you read this manual carefully before installation.
Models Parameters (Fan Only):-
MMF133MBR 1320mm 3 Blade Ceiling Fan Matt Black/Bamboo with remote control
MMF133MMR 1320mm 3 Blade Ceiling Fan Matt Black with remote control
MMF133OWR 1320mm 3 Blade Ceiling Fan Walnut with remote control
MMF133WWR 1320mm 3 Blade Ceiling Fan White with remote control
Models Parameters (Fan and Light):-
MMF1333MBR 1320mm 3 Blade Ceiling Fan Matt Black/Bamboo, 15W Tricolour LED Light with Remote Control
MMF1333MMR 1320mm 3 Blade Ceiling Fan Matt Black, 15W Tricolour LED Light with Remote Control
MMF1333OWR 1320mm 3 Blade Ceiling Fan Walnut, 15W Tricolour LED Light with Remote Control
MMF1333WWR 1320mm 3 Blade Ceiling Fan White, 15W Tricolour LED Light with Remote Control
Part List:
Qty 1x motor assembly Qty 1x instruction manual Qty 1x screw kit
Qty 1x balancing kit Qty 1x hanging bracket Qty 1x remote control kit
Qty 3x blades
Application
Flat Surface / Ceiling Slope Ceiling up to 15° Corrugated Ceiling Apex Ceiling
How to Assemble
Secure the hanger bracket
to ceiling beam or a suitable
piece of timber inserted
between the ceiling beams
using the two long screws
supplied with the package.
(See Fg.1)
Place circular shockproof
gasket above the hanger
bracket. Align the bracket
and screw the hanger
bracket to the ceiling tightly.
(See Fg.2)
Place fan into hanger
bracket and align Ball Joint
Slot with hanger bracket as
illustrated.(See Fg.3)
After wiring is completed,
attach the canopy to the
hanger bracket by pushing
upwards and twisting anti-
clockwise. Tighten screws
and ensure canopy is not
touching the ball joint.
(See Fg.4)
Fg.1 Fg.2 Fg.3 Fg.4

E: [email protected] | P: 02 8778 7500
www.martecaustralia.com.au
WARNING Installation MUST carry out by a qualied and licensed electrician.
How to Install Blades
Push top housing upward. Attach the blade to the top of
the motor using the 2 blade screws provided. Tighten the
screws and repeat this procedure for all blades. (See Fg. 6)
Fg.6 - Fan and Light
Attach the blade to the top of the motor using the 2 blade
screws provided. Tighten the screws and repeat this
procedure for all blades. (See Fg. 5)
Fg.5- Fan Only
How to Install / Remove the Glass Shade
To install - place the glass shade and spin it clockwise.
To remove - turn the glass shade anti-clockwise.
(See Fg.7)
Fg.7
CCT (Colour Changeable Temperature)
Choose colour temperature by icking the switch in the
LED (See Fg.8)
C = 3000K cool white
N = 4000K neutral white
W = 5000K warm white
Fg.8

E: [email protected] | P: 02 8778 7500
www.martecaustralia.com.au
WARNING Installation MUST carry out by a qualied and licensed electrician.
Instructions and Functions of Transmitter
1. LED indicator light
2. Light ON/OFF
(Use to dim light within 1s)
3. Speed of the fan
(1 high speed - 5 low speed)
4. Timing control of the fan
5. Direction of the fan (reverse
switch)
6. Fan ON/OFF
7. 12v battery to be used
in transmitter
NB: Remote shown fan only NB: Remote shown fan and light
1. LED indicator light
2. Speed of the fan
(1 high speed - 5 low speed)
3. Timing control of the fan
4. Direction of the fan (reverse
switch)
5. Fan ON/OFF
6. 12v battery to be used in
transmitter
Installing Receiver Remote Control NB: Receiver shown fan and light
NB: Receiver shown fan only
Antenna wire (black wire)
Important Reminders
• Receiver must be correctly installed in the mounting bracket
• When the transmitter cannot control the receiver, please check
i) has sucient battery in the transmitter
ii) any existence of similar remote controlled products nearby that cause interference
• Replace battery if getting low as this will aect sensitivity of the transmitter
• Take the battery out from the transmitter when leaving used for a long time to avoid battery leaks
• Support up to 200W lighting power
• Isolation switch MUST be connected in the line
• Dimming switch on the light models is operated by tuning the light ON/OFF button within 1s. Light output will dim
in stages from 24W to 9W to 3W approximately
NB: Receiver shown fan and light
Antenna wire (black wire)

E: [email protected] | P: 02 8778 7500
www.martecaustralia.com.au
WARNING Installation MUST carry out by a qualied and licensed electrician.
Wire Connections
NB: Remote Control with light
240V Supply
1
1
2
2P Plug
4P Plug
2
To the
Fan Light
To AC
Power
NB: Remote Control without light
1
1
WARNING
• Installation of fans MUST follow SAA standards and meet local authority regulations.
• Installation MUST be carried out by a qualied and licensed electrician.
• Fan and light MUST be earthed.
• Bracket MUST be rmly attached to a at solid structure or timber frame.
• DO NOT mix blades from one model to another, all blades MUST be replaced if damaged.
• The warranty is VOID if product is not installed according to this installation guide.
6* Year Warranty
Visit our website for details https://www.martecaustralia.com.au/warranty-statement/
240V Supply
4P Plug
2
To the Fan Motor
2
1
1
To the Fan Motor
2P Plug
To AC
Power