Martem TELEM-AGC User manual

KAUGJUHTIMISSÜSTEEMID
TELECONTROL SYSTEMS
Data Concentrator TELEM-AGC
User Manual
Martem AS
2018

Contents
1. INTRODUCTION................................................................................................................................. 3
2. FEATURES ......................................................................................................................................... 4
3. TECHNICAL DATA............................................................................................................................. 5
4. TERMINAL CONNECTORS ............................................................................................................... 7
5. COMMUNICATION CABLES ............................................................................................................. 8
6. FIRMWARE UPDATE......................................................................................................................... 9
7. DIP SWITCHES................................................................................................................................. 10
8. INDICATION LED-S.......................................................................................................................... 10
9. CONFIGURATION TOOL................................................................................................................. 10
10. ORDER CODE ................................................................................................................................ 11
11. OPEN-SOURCE SOFTWARE INFORMATION ............................................................................. 12

AS Martem Data Concentrator TELEM-AGC User Manual Rev. 1 / 2018
AS MARTEM Tel: [phone] [email protected] www.martem.eu
- 3-
1. Introduction
TELEM-AGC is designed for use in electrical networks as an communication
concentrator and as a 4G modem.
Main applications of TELEM-AGC are:
To operate as 4G modem with or without Data Concentrator software with
possibility for direct protocol translation from IEC 60870-5-101 to IEC 60870-5-
104 and vice versa
Cross-referencing of data exchange protocols
Creating transparent TCP/IP to serial channels for remote connections to
various equipment (for remote handling of various equipment)
Comprehensive integration of different devices
Full scale data exchange between substation devices and substation control
system including setting values, measurement values, registered fault
parameter values, changes of state with associated time markings etc.

AS Martem Data Concentrator TELEM-AGC User Manual Rev. 1 / 2018
AS MARTEM Tel: [phone] [email protected] www.martem.eu
- 4-
2. Features
Transparent TCP/IP connections via Ethernet and serial ports
Various data exchange protocols via Ethernet and serial ports
Cross-referencing of data exchange protocols
Automatic protocol conversion from IEC 60870-5-101 to IEC 60870-5-104
without description of data objects.
Firewall functionality
OpenVPN, IPsec, L2TP and SSH connections
SNMP (Simple Network Management Protocol)
SDN (Software Defined Networking)
DPI (Deep Packet Inspection)
Syslog
Graphic Web Server
A user-friendly free configuration tool
Configurable remotely over communication line
Configuration export to ASCII, CSV format files
TELEM RTU devices can be remotely configured via TELEM-AGC
Logical operations between digital and analog signals
Data sending with time and quality stamp
Console port
Several time synchronization options (possible to synchronize from multiple
control centers. TELEM-AGC is used to synchronize substation devices by
protocol)
GPS input
NTP client and server
All ports are galvanically isolated from case and power circuit
1-wire sensor port (up to 10 sensors) e.g. for temperature sensor
Real-time clock with back-up capacitor

AS Martem Data Concentrator TELEM-AGC User Manual Rev. 1 / 2018
AS MARTEM Tel: [phone] [email protected] www.martem.eu
- 5-
3. Technical Data
Data communication protocols
To higher level systems:
IEC 60870-5-104
IEC 60870-5-101 unbalanced and balanced,
To lower level devices:
IEC 60870-5-104,
IEC 60870-5-103,
IEC 60870-5-101 Unbalanced,
Modbus-RTU,
Modbus-TCP,
IEC 62056-21 (IEC 1107),
SPA-Bus
Communication ports
Communication ports may be freely configured for upper or lower level ommunication
Base board
2 x Ethernet connection with RJ45 port. 1,5kV isolation
3 x RS-232 with RJ12 connector, galvanically isolated. 15 kV surge
protection
2 x RS-485/232. RJ45 connector for RS-232 and screw terminals for
RS-485, galvanically isolated. 15 kV surge protection
1 x Console mini USB port
1 x optical RS232 or GPS port
1-wire for environmental sensors
Expansion modules
Module D
8 optically isolated dry contact digital inputs (connected to dry contacts)
3 double digital outputs (relay contacts max. 0.3A 110VDC,
2A 30VDC, 0.5A 125VAC)

AS Martem Data Concentrator TELEM-AGC User Manual Rev. 1 / 2018
AS MARTEM Tel: [phone] [email protected] www.martem.eu
- 6-
Module E (2 IO cards)
16 optically isolated dry contact digital inputs (connected to dry
contacts)
6 double digital outputs (relay contacts max. 0.3A 110VDC, 2A 30VDC,
0.5A 125VAC)
Module L 3 x RJ45 Eth.
Module O 2 x Optical Eth. + RJ45 Eth.
Serial data communication parameters
1 start bit
Odd, even or no parity
Communication rates from 300 to 115200 bit/sec
Electrical characteristics of isolated input
Dielectric withstand IEC 60255-5
Withstand to static discharge IEC 61000-4-2
Withstand to surges, bursts IEC 61000-4-4, 61000-4-5
Mechanical parameters
Degree of protection IP 31
Dimensions W x H x D (without connectors) 67 x 148 x 190 mm
Ambient temperature in operation –40°C…+70°C
Weight 900 g
Mounting DIN rail
Relative humidity 95% non-condensing
Radio frequency compatibility
RF emission IEC 55022 Class A
Immunity to RF fields IEC 61000-4-3, 61000-4-6
Power supply
Supply voltage range 11…33 or 20…60 V DC
Power consumption < 7 W, < 18 W with optical Eth.

AS Martem Data Concentrator TELEM-AGC User Manual Rev. 1 / 2018
AS MARTEM Tel: [phone] [email protected] www.martem.eu
- 7-
4. Terminal Connectors
RJ12
C2 RS232
RJ45
Reset
Default Setup
SG 4
Tx 3
Rx 2
SG 1
Console
Modem
Run
Alert
Telem-AGC
MAIN BOARD, FRONT PANEL
DOWNSIDE
1-WIRE
SIM 2
GPRS
Antenna
COMMON
DI 13
DI 14
DI 15
DI 16
DI 9
DI 10
DI 11
DI 12
DO 5
on
off
on
off DO 4
DO 6
on
off
OPTIONAL INTERFACES
See order codes
UPSIDE
SD
C1 RS232
ETH 1
RJ9-4P4C
POWER
SIM 1
RJ45
ETH 0
C3 RS232
RJ12
RJ12
SG 4
Tx 3
Rx 2
SG 1
SG 4
Tx 3
Rx 2
SG 1
Rx
+ + +
C3Pulse
RxTx
C2GPS
C4
or
COMMON
DI 5
DI 6
DI 7
DI 8
DI 1
DI 2
DI 3
DI 4
DO 2
on
off
on
off DO 1
DO 3
on
off

AS Martem Data Concentrator TELEM-AGC User Manual Rev. 1 / 2018
AS MARTEM Tel: [phone] [email protected] www.martem.eu
- 8-
5. Communication cables

AS Martem Data Concentrator TELEM-AGC User Manual Rev. 1 / 2018
AS MARTEM Tel: [phone] [email protected] www.martem.eu
- 9-
6. Firmware update
NB! Before updating to new firmware read the setup from your device, and
make a backup.
Run GWS.exe and set up SSH connection with the device
Press the Upd▼button next to R W C
buttons
If you have compressed .7z firmware update
file (provided by Martem AS) choose Update
From File
If you do not have .7z firmware update file choose Check martem.ee to
refresh exsisting firmware versions list for this AGC-L device
Press Update to feature and choose needed firmware version. Download is
starting...
After firmware is downloaded Confirm window appears. Press Yes button, the
update process starts
Wait until the device resumes to its normal operation state (RUN LED will start
slow blinking again)
Firmware update is complete.
Checking results of the firmware update operation:
Press Rbutton to read back the device setup data
Check the Version from GWS Status tab

AS Martem Data Concentrator TELEM-AGC User Manual Rev. 1 / 2018
AS MARTEM Tel: [phone] [email protected] www.martem.eu
- 10 -
7. DIP switches
Reset: Switch RESET to ON state and then back to OFF state for Reset operation
Dft. Set: To apply default setup:
1. Switch DFT. SET to ON state
*Alert indication LED starts blinking within 5 seconds
*Alert indication LED will blink for 2 seconds
2. Switch DFT. SET back to OFF state when the alert indication LED is
blinking to apply default setup
*If DFT. SET is switched back to OFF state when the alert indication LED is not
blinking, default setup will NOT be applied
8. Indication LED-s
MODEM –green LED –indicates the 4G (3G) modem network connection
RUN –green LED –blinking green indicates that the program is running
ALERT –red LED –failure
Green LED-s for serial communication ports for RX, TX indication.
9. Configuration tool
The Telem-AGC device is configured with Telem-GWS software.
The configuration process is described in Telem-GWS software manua