martens GTL720 User manual

Operating Manual
Clamp-on Temperature Sensor
GTL720
EN
Save for later reference!

Clamp-on Sensor GTL720
Table of contents
1Proper use (application areas)........................................................................................................................1
1.1 Safety signs and symbols...................................................................................................................................1
1.2 Safety instructions..............................................................................................................................................2
1.3 Product liability and guarantee...........................................................................................................................2
1.4 Standards and directives....................................................................................................................................2
2Product description .........................................................................................................................................3
2.1 Delivery content..................................................................................................................................................3
2.2 Operating principle.............................................................................................................................................3
2.3 Design of the measurement system...................................................................................................................4
2.4 Type plate ..........................................................................................................................................................4
2.5 Step response of clamp-on sensor..................................................................................................................... 5
3Mounting and electrical installation ...............................................................................................................6
3.1 Mechanical mounting .........................................................................................................................................6
3.2 Mounting guidelines ...........................................................................................................................................6
3.3 Mounting notes................................................................................................................................................... 7
3.4 Instruction on Ordinance (EC) 1935/2004..........................................................................................................7
3.5 Electrical installation...........................................................................................................................................8
3.6 Connction diagram.............................................................................................................................................8
4Commissioning, Maintenance and Servicing ................................................................................................8
4.1 Commissioning...................................................................................................................................................8
4.2 Maintenance.......................................................................................................................................................8
4.3 Servicing ............................................................................................................................................................9
4.4 Calibration / Adjustment.....................................................................................................................................9
5Faultfinding..................................................................................................................................................... 10
6Technical Data................................................................................................................................................ 11
6.1 Mechanical design / dimensions.......................................................................................................................12
7Ordering code................................................................................................................................................. 13
7.1 Accessories......................................................................................................................................................15
8Device transport and storage........................................................................................................................ 15
8.1 Returns.............................................................................................................................................................15
8.2 Disposal ........................................................................................................................................................... 16
9Service ............................................................................................................................................................ 16
9.1 Manufacturer....................................................................................................................................................16
9.2 Service processing........................................................................................................................................... 16
10 EU-Declaration of conformity........................................................................................................................ 17

Clamp-on Sensor GTL720
BA_MA_GTL720_EN_V1.08
1 / 17
BA_MA_TC125_EN_V0.13
1 Proper use (application areas)
Detailed information on the application area can be found in the Chapter
2 Product description
The operating safety of the device is ensured only with proper use and observation of the information given in
the operating instructions.
For safety and guarantee reasons, work above and beyond that described in the operating instructions may
only be carried out by personnel authorized by the manufacturer. Unauthorized conversions or modifications
are expressly prohibited.
In the event of improper use, this device can pose dangers, depending on the application.
Additional requirements for use in potentially explosive atmospheres:
1) The piping adapters must be mounted on a grounded metal pipe.
2) In the case of size 4 pipe adapters, the clamp jacket must also be grounded.
3) Operation with approved evaluation electronics (associated equipment), only.
4) When using thermal compound, it is important to ensure that only electrically conductive thermal paste
is used.
General safety instructions, use
These operating instructions must be kept where they are immediately available to specialist personnel at
all times.
Only trained personnel authorized by the operator, while wearing the corresponding protective clothing must
carry out all procedures described in these operating instructions.
All rights reserved.
1.1 Safety signs and symbols
Warning instructions are designated in this document as described below in Table:
Table 1 Safety signs and symbols
Danger
Warning! This symbol warns against immediately threaten- ing danger, death, severe physical
injury or serious material damage if instructions are not followed.
Attention! This symbol warns against possible dangers or dangerous situations, which can
cause damage to the de- vice itself or to the environment if instructions are not followed.
Note! This symbol indicates procedures, which have a direct influence on operation or can
cause unforeseen reactions if instructions are not followed.
Warning! In front of an area in which explosive atmospheres can occur.
This only applies to devices with an ATEX approval.
Danger

Clamp-on Sensor GTL720
2 / 17
BA_MA_GTL720_EN_V1.08
1.2 Safety instructions
Read the product description before bringing the device into operation. Ensure that the product is fully
suitable for the applications in question.
The operator is responsible for the problem-free operation of the device. The operator is obliged through-
out the complete usage time to establish and ensure that the required working and safety measures
comply with the relevant applicable regulations.
1.3 Product liability and guarantee
Liability disclaimer:
The content of the operating instructions has been checked for compliance with the device described. Deviations
cannot however be excluded, so that we offer no guarantee of full compliance. The information in these instruc-
tions is checked regularly, and necessary corrections incorporated into the following editions. We reserve the
right to make technical amendments. All claims are also subject to the valid “General delivery conditions for
products and services of the electronics industry”.
GHM Messtechnik cannot check or repair devices without the specified, fully completed form (see
chapter 8.1 Returns ).
1.4 Standards and directives
Conformity
Explosionsgefährdete Bereiche 60079-0:2018
60079-11:2012
Vibrations EN 60068-2-6:2008
FDA conform
Danger

Clamp-on Sensor GTL720
BA_MA_GTL720_EN_V1.08
3 / 17
BA_MA_TC125_EN_V0.13
2 Product description
The GTL720 pipe clamp-on sensors are especially useful as an alternative to invasive and inline-measuring
procedures for monitoring sterilization processes. Without disturbing the process, the special clamp-on
mechanics make the systems flexible, absolutely dead spot-free, and usable without high installation costs.
This measuring procedure permits high-precision results.
The pipe clamp-on sensor consists of a sensor insert with the Pt100 sensor and the pipeline adapter. The
electric contact is achieved by means of a three-wire system and an M12 round connector.
Block diagram
Figure 1 Block diagram
2.1 Delivery content
Clamp-on Sensor GTL720
Pipeline adapter, RLA (separate ordering position)
Silicone insert (RLA included)
This operating manual (GTL720 included)
2.2 Operating principle
The GTL720 pipe clamp-on sensor measures temperatures of liquids in metal pipelines without a process con-
nector touching the fluid. For this purpose, the pipe clamp sensor is mounted on the exterior of the pipe at a
suitable site. The sensor plate is pressed to the exterior of the pipe wall by a spring. Constant pressure and
shielding the silicone from the ambient air guarantee an optimal thermal transfer. The one-piece measuring
insert, which is manufactured from premium-quality synthetic material prevents undesirable heat dissipation and
reduces the response time. The sensor plate inside the measuring insert is in direct thermal contact with the
Pt100 sensor.

Clamp-on Sensor GTL720
4 / 17
BA_MA_GTL720_EN_V1.08
Pipe-Ø: DN10...DN80
2.3 Design of the measurement system
The GTL720 measuring system consists of an RLA piping adapter and a GTL720 measuring insert.
Figure 2 Design of measurement system
2.4 Type plate
The nameplate contains the most important identification data:
Connection diagram
Manufacturer
Type and article designation
Technical data
Serial number
Figure 3 Type plate GTL720
Figure 4 Type plate RLA
Insertion GTL720
Clamp-on adapter
RLA
Type plate
insertion GTL720
Type plate
Clamp-on adapter RLA
Silicon insertion
RLA
Sensor insertion with
round plug M12,
360° turn able

Clamp-on Sensor GTL720
BA_MA_GTL720_EN_V1.08
5 / 17
BA_MA_TC125_EN_V0.13
2.5 Step response of clamp-on sensor
Reference conditions
Pipe diameter
29 mm
Pipe wall thickness
1,5 mm
Pipe material
1.4404
Flow rate
0,5 ~ 1,5 m/s
Ambient temperature
30 °C
Medium
Water
Mounting direction
Acc. to position 1, 3.1 Mechanical mounting
Table 2 Reference condition for step response
Figure 5 Step-response (T90) in water, without thermal compound
Figure 6 Step-response (T90) in water, with thermal compound
GTL720 step-response (without thermal compound)
Medium (Water)
GTL720
GTL720 step-response (with thermal compound)
Medium (Water)
GTL720

Clamp-on Sensor GTL720
6 / 17
BA_MA_GTL720_EN_V1.08
3 Mounting and electrical installation
3.1 Mechanical mounting
The RLA pipe clamp sensors are available in three sizes. The adapters are adjusted to the pipe diameter (DN10
to DN80) with different highly heat- resistant silicone inserts.
Frame size (Bg)
Pipe Ø [mm]
1
12,0..19,0
2
20,0..33,9
3
34,0..53,0
4a
60,3..75,9
4b
76,0..88,9
Table 3 Frame size and pipe diameter
Available for pipe standards: DIN 11850 r1, r2 and DIN11866 rB, rC.
The cap nuts of the two adapter parts should be torqued to a value from 0.5 to 1 Nm (0.37 to 0.74 ft-lb) to avoid
a deformation of the silicone insert, which would prevent a correct fitting of the pipes.
For the same reason, all cap nuts must be torqued equally. This is especially important for pipes with small
diameters without the use of heat-conductive paste.
3.2 Mounting guidelines
For mounting instructions, see Figure 7 Permissible types of mounting
To ensure secure functionality and the best measuring results, please follow these mounting steps:
1. The pipe diameter should not deviate more than ± 1 % from the nominal diameter of the silicone insert.
2. Clean the exterior of the pipe before installation. Be sure that no chips, swarf, or other particles are
lodged between sensor and pipe because this would prevent the contact plate of the sensor from
being flush against the pipe, which reduces accuracy.
3. The installation site should be at least 15 cm (6 inches) from pipe el- bows, pipe reducers, and radial
welded seams. The sensor must not be placed on welded seams of axially welded pipes. The sensor
should be installed at a distance of at least15 cm (6 inches) from other installed sensors with fluid
contact.
4. Behind pipe elbows, the sensor housing should be installed on the out- side to prevent measuring
errors due to bubble formation or flow characteristics.
5. If the pipes are not completely filled, the sensor should be installed in the fluid-covered area of the
pipe.
6. Unilateral strain due to suspending heavy objects or taut connection wires should be avoided.
The sensor plate must be flush against the pipe.
7. If thermal compound is used between pipe wall and measuring tip, it should be replaced in the mainte-
nance interval according the maximum storage period of the paste.
8. The electrical installation must be made after the pipeline adapter is installed on the process line.

Clamp-on Sensor GTL720
BA_MA_GTL720_EN_V1.08
7 / 17
BA_MA_TC125_EN_V0.13
3.3 Mounting notes
Figure 7 Permissible types of mounting
Position
Characteristics
1
Ideal:
Achieves the best result, since there are no bubbles, deposits, or rising lost heat in the pipes
to distort the measuring result.
2
Questionable:
Lost heat and moving the contact area may lead to distorted measuring results.
3
Ideal:
Good measuring result, if no air bubbles form. Minimum distance to pipe angle 15 cm (6
inches)
4
Questionable:
Lost heat and too small a distance from the connection flange may lead to distorted measur-
ing results.
Table 4 Description to Fig. 7
3.4 Instruction on Ordinance (EUR) 20/1011 / (EC) 1935/2004
The following components of the product are designed in accordance with Ordinance for permanent contact
with foodstuffs:
FDA approved components
Flow direction
min. 15 cm
min. 15 cm
min. 15 cm

Clamp-on Sensor GTL720
8 / 17
BA_MA_GTL720_EN_V1.08
3.5 Electrical installation
The electrical connection happens via the M12 round connector. For the wiring see Figure 8 Connection
diagram.
The device must be installed only by a qualified electrician. The national and international regulations for the
installation of electrical systems of the relevant operator country apply.
Additional requirements for use in potentially explosive atmospheres:
1) The temperature sensor GTL must be connected to an for intrinsic safety certified Ex-transmitter.
2) The temperature sensor GTL must be used together with the clamp-on adapters RLA.
3) The clamp-on adapters must be mounted on a grounded tube.
4) The declarations are only valid for operating conditions, which means the sensor must touch the pipe,
possibly with conductive thermal compound.
5) For RLAs in FS.4 the metal clamp must be grounded.
3.6 Connection diagram
View at the plugs:
Connection design 1 (standard)
Connection design 2 (customized)
4 Commissioning, Maintenance and Servicing
4.1 Commissioning
1. Be sure that the pipe clamp sensor is flush with the pipe.
2. Be sure that the M-12 connector is screwed on correctly and the cable is not pulling on the sensor.
3. Check the correct measuring function after connecting the evaluation device.
4.2 Maintenance
Housing
When cleaning the device, make sure that its connections are firm and tight. Cleansers must not harm the
housing surface and gaskets.
If the housing is cleaned with a high-pressure cleaning device, make sure the electric connection and the
device are not sprayed directly. Avoid cleanser deposits on the thread and inside the guide of the interior
part.
Sensor
During cleaning, it is essential not to damage the sensor tip. If cleansers are used, make sure that they do not
harm any materials.
Figure 8 Connection diagram
Danger
Danger