Martha Stewart Lionel User manual

ASSEMBLY INSTRUCTIONS
Page 1 of 3
Description: Lionel Bar Cart
Pre-assembly:
Remove all parts and hardware from box along with any plastic protective packaging.
Do not discard any contents until after assembly is complete to avoid accidentally discarding small parts or
hardware.
Important safety instructions:
Please carefully read all instructions before assembling.
For your safety and ease, assembly by two or more adults is recommended.
Keep instructions for future use.
Description QTY
Parts List
Item
1
P1
1
2
Casters
Top Glass
Top Frame
Left Side Frame
Hardware List
4
1
1Ceramic
Back Rails
Bottom Frame
Right Side Frame 1
1
QTY
Description
Item
8
H1 Short Bolts Ø1/4" *1/2"
Allen Wrench 4mm 1
4
Flat Washers Ø1/4"
4
4
Countersunk Bolts Ø1/4" *3/4"
Clear Plastic Pad 6
1
Open Wrench
P2
P3
P4
P5
P6
P7
P8
H2
H3
H4
H5
H6
H7
Long Bolts Ø1/4" *3/4"
Label W/ "Top"
Label W/ "Bottom"

Page 2 of 3
Step 2.
1) Use short bolts (H1) to attach the rails (P5) to two side frames (P3/P4).
2) Securely tighten the casters (P8) to the side frames (P3/P4) through the flat washers (H4) with open wrench
(H6) as shown below.
Assembly Procedures:
Step 1. Assemble the bar cart on a flat, soft surface such as a carpet or cloth to prevent scratching the finish.
1) Insert the inserted bar on side frame (P3, P4) to back rails (P5).
2) Attach top frame (P1) to two side frame (P3, P4) using long bolts (H2), make sure the frame have a label with
"Top" and make sure the arrow of label on a end of top frame (P1) in the direction of the floor. the inserted bar
on side frame (P3, P4) to back rails (P5).
2) Attach bottom frame (P2) to two side frame (P3, P4) using countersunk bolts (H3), make sure the frame have a
label with "Bottom" and make sure the arrow of label on a end of top frame (P1) in the direction of the floor.
Inserted
bar P5
P3
P1
P2
P5
P4
H7 H2
H7 H3
P8
P8
H4
H1
H7
H6
Label with "Top"
Label with "Bottom"
P8
P8
Allen Wrench
(H2)x4
(H7)x1
Long Bolts
(H1)x8 Short Bolts
Allen Wrench
Open Wrench
(H6)x1
(H7)x1
P5
P5
P4
P3
Flat Washers
(H4)x4
Countersunk Bolts
(H3)x4
Arrow label on the
end of bottom frame
Arrow label on the
end of top frame

P6
P7
H5
Page 3 of 3
Thank you for your purchase
Caution: Failure to follow these instructions may cause the bolts to misalign during assembly.
ADDITIONAL NOTE ABOUT SAFETY: BOLTS MAY LOOSEN DURING NORMAL EVERYDAY USE. THEY SHOULD BE
PERIODICALLY INSPECTED AND RE-TIGHTENED TO PREVENT DAMAGE OR INJURY. ALWAYS CHECK TO BE SURE THAT ALL
HARDWARE IS KEPT TIGHTENED.
Step 4.
1) Gently lay the ceramic (P7) on the bottom frame of bar cart. Assembly is complete.
Step 3.
1) Turn the assembled bar cart to an upright position.
2) Make sure the assembled bar cart is level and securely tighten all bolts with Allen wrench (H5).
3) Place the clear plastic pad (H5) on the assembly top frame as shown below.
4) Gently lay the glass (P6) on the table top.
Clear Plastic Pad
(H5)x6