Martin Professional Ego 02 User manual

Ego 01
Ego 02
Logo Projector
user manual

Measurements are expressed in millimeters.
305
324
248
150
© 2002 Martin Professional A/S, Denmark.
All rights reserved. No part of this manual may be reproduced, in any form or by any means,
without permission in writing from Martin Professional A/S, Denmark.
Printed in Denmark.
P/N 35000109, Rev. C

3
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Ego 01 / Logo Projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Ego 02 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Safety information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
AC power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Installing a plug on the mains lead . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Overhead mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Operation from the floor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Linking multiple Egos for simultaneous control . . . . . . . . . . . . . . . . . . . . . . . . 9
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Setting the trig mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Adjusting the effects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Focusing the Ego . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Selecting the gobo on an Ego 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Operation with the optional remote control . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Basic service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Lamp maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Gobo replacement or removal (Ego 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Firmware updates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

4 Ego user manual
I NTRODUCTION 1
Thank you for selecting the Martin Ego. The Ego series features 250 watt flower
effects with sharp projection quality optics in a moulded composite-plastic
casing. They incorporate a 250-watt, 500-hour halogen lamp and a precise focus
adjustment that produces crisp projections.
Variable behavior tuning, by adjusting the dynamic, allows you to modify the
aggressiveness of the effect in relationship to the music - relaxed, intermediate or
quick. The Ego operates in either auto or music trig mode.
A convenient handle and lens protection ring make for easy transport and
handling. A remote control is also available that enables the simultaneous control
of multiple Ego fixtures.
EGO 01 / LOGO PROJECTOR
The Ego 01 provides a flower effect with a range of gobos and colors on a single
effect wheel. In addition to variable behavior tuning, effect wheel and mirror dish
rotation speeds are controllable.
The Logo Projector is the same as the Ego 01, but it is primarily used to project
images around a specific theme.
EGO 02
The Ego 02 features an overlapping color wheel system offering more than 200
color combinations and a manually selectable image effect (etched gobo or
textured glass gobo pattern). An interchangeable gobo slot is available so that you
can incorporate your own custom patterns or accessories. In addition to variable
behavior tuning, the rotation speeds of the color wheels and mirror dish are also
controllable.

Introduction 5
SAFETY INFORMATION
Warning! This product is not for household use. It presents risks of
lethal or severe injury due to fire and heat, electric shock, and
falls.
Read this manual before powering or installing the fixture, follow the safety
precautions listed below and observe all warnings in this manual and printed on
the fixture. If you have questions about how to operate the fixture safely, please
contact a Martin distributor for assistance. Refer any service operation not
described in this manual to a qualified technician. Do not modify the fixture or
install other than genuine Martin accessories and upgrade kits.
Avoiding electric shocks
• Disconnect the fixture from AC power before removing or installing the lamp,
fuses, or any part, and when not in use.
• Always ground (earth) the fixture electrically.
• Use only a source of AC power that complies with local building and electrical
codes and has both overload and ground-fault protection.
• Do not expose the fixture to rain or moisture.
• Refer all service to a qualified technician.
• Never operate the fixture with missing or damaged lenses and/or covers.
Protecting yourself and others from burns and fire
• Never attempt to bypass the thermostatic switch or fuses. Always replace
defective fuses with ones of the specified type and rating.
• Ensure that the air flow through fans and vents is free and unobstructed.
• Keep all combustible materials (for example fabric, wood, paper) at least 0.1
meters (4 inches) away from the fixture. Keep flammable materials well away
from the fixture.
• Do not illuminate surfaces within 0.3 meters (12 inches) of the fixture.
• Provide a minimum clearance of 0.1 meters (4 inches) around fans and air vents.
• Replace the lamp if it becomes defective or worn out, or before usage exceeds the
maximum service life. When replacing the lamp, allow the fixture to cool for at
least 5 minutes before opening the fixture or removing the lamp. It can take up to
15 minutes for the fixture to cool completely.
• Never place filters or other materials over the lens or mirror drum.
• The exterior of the fixture can become hot. Allow the fixture to cool for at least 5
minutes before handling.
• Do not operate the fixture if the ambient temperature (Ta) exceeds 40° C (104°
F).
• Do not stare directly into the light.

6 Ego user manual
• Never operate the fixture without all lenses and covers installed: an unshielded
lamp emits dangerous UV radiation that can cause burns and eye damage.
Preventing injuries due to falls
• When suspending the fixture above ground level, verify that the structure can
hold at least 10 times the weight of all installed devices.
• Verify that all external covers and rigging hardware are securely fastened and use
an approved means of secondary attachment such as a safety cable.
• Block access below the work area whenever installing or removing the fixture.
UNPACKING
The packing material is carefully designed to protect the fixture during shipment -
always use it to transport the fixture.
The Ego comes with the following:
• 1.5-meter, 3-wire IEC power cable.
•Usermanual.

AC power 7
AC POWER 2
The Ego has an auto-ranging power supply that can operate in the following
voltage ranges at 50-60 Hz:
• 90-130 volts
• 200-260 volts
INSTALLING A PLUG ON THE MAINS
LEAD
The fixture’s mains lead may require a grounding-type cord cap that fits your
power distribution cable or outlet. Consult a qualified electrician if you have any
doubts about proper installation.
Warning! For protection from dangerous electric shock, the fixture
must be grounded (earthed). The AC mains supply shall have
overload and ground-fault protection.
Important! Verify that the feed cables are undamaged and rated for the
current requirements of all connected devices before use.
Following the cord cap manufacturer’s instructions, connect the yellow and green
wire to ground (earth), the brown wire to live, and the blue wire to neutral. The
table below shows some pin identification schemes.
Wire Pin Marking Screw color
brown live “L” yellow or brass
blue neutral “N” silver
yellow/green ground green

8 Ego user manual
I NSTALLATION 3
The Ego can be hung overhead with a clamp (not included), mounted vertically
on a wall, or placed on the floor.
Warning! Block access below the work area before proceeding. Always
use a secure means of secondary attachment.
OVERHEAD MOUNTING
To hang the Ego on an overhead support, ceiling, or wall:
1 Verify that the structure can support
at least 10 times the weight of all
installed fixtures, clamps, cables,
auxiliary equipment, and other
items.
2 If hanging the fixture with a rigging
clamp, verify that the clamp is
undamaged and is designed for the
fixture’s weight. Bolt the clamp
securely to the mounting bracket on
the fixture with a grade 8.8
(minimum) M12 bolt and lock nut,
or as recommended by the clamp
manufacturer, through the clamp
hole in the mounting bracket.
3 If permanently installing the fixture,
verify that the hardware (not
included) and mounting surface can
bear at least 10 times the fixture’s
weight.
4 Working from a stable platform,
clamp or fasten the fixture to the
structure.
Rigging clamp Safety cable

Installation 9
5 Install a safety cable that can hold at least 10 times the weight of the fixture through
the handle of the of the fixture.
6 Loosen the swivel locks, tilt the fixture to the desired angle, and retighten.
7 Verify that the fixture is at least 0.3 meters (12 in.) from the surface to be
illuminated and at least 0.1 meters (4 in.) from any combustible materials. Verify
that the clearance around the air vents is at least 0.1 meters (4 in.).
OPERATION FROM THE FLOOR
To operate the Ego from the floor:
1 Set the fixture on the floor so that the mounting
bracket is under the fixture. Adjust the mounting
bracket and tighten both swivel locks. Note that
the fixture may not be placed so that the clearance
around the air vent is impaired.
2 Verify that the fixture is stable, that it is at least 0.3
meters (12 in.) from the surface to be illuminated
and at least 0.1 meters (4 in.) from any
combustible materials. Verify that the clearance
around the air vents is at least 0.1 meters (4 in.).
Do not operate the fixture while it lies flat
without the mounting bracket extended as this
reduces the air flow to the fan; the fixture may
overheat and then the thermostatic switch will
temporarily cut the power.
LINKING MULTIPLE EGOS FOR
SIMULTANEOUS CONTROL
You can link multiple Egos using speaker cables with stereo mini-jack connectors
for the purpose of controlling them using the optional remote control.
The remote control is connected with a cable to the Remote In socket of the first
Ego fixture. Additional cables are used from the Remote Out sockets to the
Remote In sockets of subsequent fixtures, and so on, until all the Ego fixtures are
connected in a daisy chain. There is no need to terminate this link.

10 Ego user manual
O PERATION 4
To achieve optimal results the use of smoke effects together with your Ego is
recommended.
The lamp turns on as soon as power is applied. The effect wheel/s and mirror dish
begin to rotate. The action is varied whenever trigger signals are generated as a
result of sounds picked up by the built-in microphone (manual trig) or randomly
(when the fixture is in auto trig mode).
SETTING THE TRIG MODE
The Idle Speed dial on the control panel is used to set the trigger mode; when the
Idle Speed dial is set:
• In the Auto Trig zone trigger signals are generated randomly in Auto Trig mode.
This will result in unsynchronized operation that is not in time with music.
• Out of the Auto Trig zone, the fixture is in Manual Trig mode and the built-in
microphone will generate trigger signals as a result of sounds that it picks up. This
will result in synchronous operation in time with any music that is being played.
When trigger signals are not being received, the effect wheel will idle at a speed
that is relative to how far clockwise the Idle Speed dial is set.
ADJUSTING THE EFFECTS
Dynamic
The Dynamic dial on the control panel is used to set the aggressiveness of the
effect, regardless of which trig mode is set. When the dial is wound fully anti-
clockwise the fixture will react relatively passively, and the level of
aggressiveness will increase the further clockwise that the dial is wound.
The separately orderable remote control unit can be used to link multiple Egos
and allows the simultaneous adjustment of their dynamics. See “Operation with
the optional remote control” on page 12 for more information.

Operation 11
Adjusting the speed of effect wheel
As long as the Idle Speed dial is not in the Auto Trig zone it is used to adjust the
speed of rotation of the effects wheel/s between trigger signals.
FOCUSING THE EGO
Adjust the focus using the thumb screw next to the lens.
SELECTING THE GOBO ON AN EGO 2
There are two manually-selectable gobos in an Ego 2, one of which is always in
the optical path. One is a fixed piece of textured glass and the other
interchangeable position is delivered with an etched gobo installed. This gobo
can be removed (see “Gobo replacement or removal (Ego 2)” on page 16).
To change the gobo that is currently in the optical path:
1 Disconnect the fixture from AC power and allow it to cool. It can take up to 15
minutes for the fixture to cool completely.
2 Remove the six access screws from the cover and lift it off. The gobo holder is
located between the lamp and the mirror dish.
3 Loosen the thumb screw on the gobo holder.

12 Ego user manual
4 Pull the tab away from the fixture base to select the textured glass, push it towards
the fixture to select the etched gobo position.
5 Tighten the thumb screw.
6 Replace the fixture cover and tighten the access screws, taking care not to trap any
loose wires.
7 Adjust the focus (see “Focusing the Ego” on page 11).
OPERATION WITH THE OPTIONAL
REMOTE CONTROL
The (separately orderable) remote control can be used
to simulations control multiple Ego fixtures that are
connected (see “Linking multiple Egos for
simultaneous control” on page 9).
A LAMP ON/OFF button is used to turn the fixtures
on and off.
A combined dimmer and intensity dial is used to set
the intensity of the light and the aggressiveness of the
effect, regardless of which trig mode is set. When the
dial is set at the beginning of the Dynamic scale, the
fixture will react relatively passively, and the level of
aggressiveness will increase the further clockwise
that the dial is wound.

Basic service 13
B ASIC SERVICE 5
This chapter describes the maintenance procedures that you can perform
yourself:
• Cleaning
• Lamp maintenance
• Replacing fuses
• Gobo replacement/removal
CLEANING
Regular cleaning of the elements in the optical path, as well as the fans and air
vents, is vital to maintaining the operational quality of the Ego.
Important! Excessive dust, smoke fluid, and particulate buildup degrades
performance and causes overheating and damage to the
fixture that is not covered by the warranty.
Cleaning the fan and air vents
To maintain adequate cooling, dust must be cleaned from the fan and air vents
periodically. Remove dust from the fan and air vents with a soft brush, cotton
swab, vacuum, or compressed air.
Cleaning optical components
Clean the optical components regularly. The presence of smudges or dust on
optical surfaces can reduce the strength of the light output and the quality of the
effects.
Use care when cleaning optical components and work in a clean, well lit area.
The coated surfaces are fragile and easily scratched. Do not use solvents that can
damage plastic or painted surfaces.
1 Disconnect the fixture from power and allow the components to cool completely.

14 Ego user manual
2 Remove the fixture cover. You may want to remove the lamp for cleaning (see the
related steps in “Installing a lamp in the Ego.” on page 14).
3 Vacuum or gently blow away dust and loose particles with compressed air.
4 Remove stuck particles with an unscented tissue or cotton swab moistened with
glass cleaner or distilled water. Do not rub the surface: lift the particles off with a
soft repeated press.
5 Remove smoke and other residues with cotton swabs or unscented tissues
moistened with isopropyl alcohol. A commercial glass cleaner may be used, but
residues must be removed with distilled water. Clean with a slow circular motion
from center to edge. Dry with a clean, soft and lint-free cloth or compressed air.
6 Replace the fixture cover and tighten the access screws, taking care not to trap any
loose wires.
LAMP MAINTENANCE
The following lamp types are supported:
• Philips ELC/5H, 24 V / 250 W, 500 hour halogen lamp (included)
• OSRAM ELC, 24 V / 250 W, 50 hour halogen lamp
Installing any other lamp may damage the fixture!
Allow the lamp to cool for at least 5 minutes before packing and moving the
fixture. To avoid possible damage, remove the lamp when shipping the fixture.
Warning! Always disconnect the fixture from AC power and allow it to
cool for 5 minutes before installing the lamp.
Installing a lamp in the Ego.
1 Disconnect the fixture from AC power. If replacing a lamp, allow it to cool for at least
5 minutes before removing the lamp-access cover. The lamp cools faster with the
cover in place. It can take up to 15 minutes for the fixture to cool completely.
2 Remove the six access screws from the cover and lift it off.

Basic service 15
3 If replacing a lamp, grasp the old lamp
by the reflector and pull it out of the
holder. Then pull the socket off the
lamp. Do not pull the wires.
4 Push the socket fully onto the pins of
the new lamp.
5 Clean the glass bulb with the cloth
supplied with the lamp, particularly if
your fingers touched the glass. A
clean, lint-free cloth wetted with
alcohol may also be used.
6 Gently push the lamp into the holder
until it snaps into place.
7 Replace the fixture cover and tighten the access screws, taking care not to trap any
loose wires.
FUSES
The Ego uses a time-delay fuse for protection against current overload. An
indication that the fuse may have blown is that when power is applied the lamp
does not light and the fan does not operate.
If the fuse blows repeatedly, there is a fault with the unit that requires service by a
Martin technician.
Never bypass the fuse or replace it with one of another size or rating.
Replacing the main fuse
1 Unplug the mains cable from the input
socket.
2 Remove the six access screws from the
cover and lift it off
3 The fuse can be found on the circuit
board, a diagram of which can be found
on the inside of the fixture cover. Use this
to locate the fuse.
4 Remove the fuse and replace the fuse
with one of the same type. The fuse

16 Ego user manual
rating is listed on the serial number label that can be found on the back of the
fixture.
5 Replace the fixture cover and tighten the access screws, taking care not to trap any
loose wires.
GOBO REPLACEMENT OR REMOVAL
(EGO 2)
You can replace (or remove) the etched gobo in an Ego 2 with another aluminium
gobo that has:
• An outside diameter of 22.5 mm + 0/- 0.3 mm (0.886 in. +0/- 0.012 in)
• A maximum image diameter of 17 mm (0.669 in)
• A maximum thickness of 1.8 mm (0.071 in)
To replace (or remove) the gobo:
1 Unplug the mains cable from the input socket.
2 Remove the six access screws from the cover and lift it off. The gobo holder is
located between the lamp and the mirror dish.
3 Remove the thumb screw on the gobo holder and lift it out to access the
interchangeable gobo holder.
4 The currently installed gobo can be pressed out of the holder gently with your
thumb.
5 If you a replacing the gobo, create a gap using a flat head screwdriver, and place
the new gobo in the holder.
6 Return the gobo holder to its normal position.
7 Replace and tighten the thumb screw.
8 Replace the fixture cover and tighten the access screws, taking care not to trap any
loose wires.
FIRMWARE UPDATES
The installed firmware version can be displayed by the Trig LED on the control
panel when both the Dynamic and Idle Speed dials are wound fully clockwise and
power is applied to the fixture. The number of slow blinks indicate the software
version number to the left of the decimal place and any following fast blinks
indicate the software version number to the right of the decimal place. For

Basic service 17
example, if firmware version 1.4 is installed, the Trig LED flashes slowly once
and then quickly four times.
Firmware is installed using a Martin AVR Uploader and a PC. To install the
firmware update, prepare the AVR Uploader as described in its user manual,
connect the uploader to the AVR Upload socket on the control panel, and apply
power to the fixture. See the AVR user manual for more information.

18 Ego user manual
T ROUBLESHOOTING 6
problem probable cause(s) suggested remedy
No light No power to the fixture Check connections
Blown fuse If fan does not function
either then check and
replace fuse if necessary.
Burned out lamp Install new lamp
Fixture to hot Allow to cool
Improve air flow around
fixture
No action Sound too low to activate
control circuit Increase volume
Move speakers closer
Electrical malfunction Refer to service technician
Fuse blows repeatedly Electrical malfunction Refer to service technician

Specifications 19
S PECIFICATIONS A
PHYSICAL
Size without standard bracket (L x W x H). . . . . . 305 x 324 x 150 mm (12 x 12.8 x 5.9 in)
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.5 kg (7.7 lb)
CONSTRUCTION
Housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . composite plastic
Finish. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .black
THERMAL
Maximum ambient temperature (Ta). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40° C (104° F)
INSTALLATION
Minimum distance to combustible materials . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.1 m (4 in)
Minimum distance to illuminated surfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.3 m (12 in)
Minimum clearance around fan and air vents. . . . . . . . . . . . . . . . . . . . . . . . . . . 0.1 m (4 in)
CONTROL AND PROGRAMMING
Stand-alone triggers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . music or auto
ELECTRICAL
Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-prong IEC male socket
AC Power . . . . . . . . . . . . . . . . . . . . . . . . . . . auto-ranging 90-130 V / 200-260 V, 50-60 Hz
Power and current consumption 240 W, 1 A @ 230 V, 50 Hz; 250 W 2.2 A @ 110 V, 60 Hz
Main fuse. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.15 A T (time delay), P/N 05020013
ACCESSORIES
Ego remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P/N 91611055
Philips ELC/5H, 24 V / 250 W, 500 hour halogen lamp. . . . . . . . . . . . . . . . . P/N 97000107
OSRAM ELC, 24 V / 250 W, 50 hour halogen lamp . . . . . . . . . . . . . . . . . . . P/N 97000104
Half-coupler clamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P/N 91602005