Sharp PG-D3750W - WXGA DLP Projector 720p User guide

MODEL
PG-D3750W
DATA PROJECTOR
SETUP MANUAL
Connecting Pin Assignments .............................. 2
RS-232C Specifications and Commands ........... 4
Setting up the Projector Network Environment ... 10
1. Connecting the Projector to a Computer ...........11
2. Setting an IP Address for the Computer ............12
3. Setting up a Network Connection for the
Projector.......................................................14
Controlling the Projector via LAN ..................... 16
Controlling the Projector Using Internet Explorer
(Version 5.0 or later)......................................16
Confirming the Projector Status (Status)................17
Controlling the Projector (Control)..........................17
Setting and Adjusting the Projector
(Settings & Adjustments) ..............................18
Setting the Security (Network – Security)...............18
Making General Settings for the Network
(Network – General).....................................19
Setting for Sending E-mail when an Error Occurs
(Mail – Originator Settings) ..........................19
Setting Error Items and Destination Addresses
to which E-mail is to be Sent when an
Error Occurs (Mail – Recipient Settings) ......20
Setting Error Items and the URL that are to be
Displayed when an Error Occurs
(Service & Support – Access URL)...............20
Setting up the Projector Using RS-232C or
Telnet .......................................................... 21
When Connecting Using RS-232C.........................21
When Connecting Using Telnet ..............................22
SETUP MENU (Main Menu)....................................23
ADVANCED SETUP MENU ....................................23
View Setting Detail List ([V]View All Setting)...........24
Set Items ................................................................24
Save Settings and Quit ([S]Save & Quit).................25
Quit without Saving Settings ([Q]Quit Unchanged) ...25
IP Address Setting ([1]IP Address) .........................26
Subnet Mask Setting ([2]Subnet Mask) ..................26
Default Gateway Setting ([3]Default Gateway) .......26
User Name Setting ([4]User Name) ........................26
Password Setting ([5]Password).............................27
RS-232C Baud Rate Setting
([6]RS-232C Baud Rate)...............................27
Projector Name Setting ([7]Projector Name) ..........27
DHCP Client Setting ([8]DHCP Client)....................27
Disconnecting All Connections
([D]Disconnect All) ........................................28
Entering ADVANCED SETUP MENU
([A]Advanced Setup).....................................28
Setting Auto Logout Time
(ADVANCED[1]Auto Logout Time)................28
Data Port Setting (ADVANCED[2]Data Port)...........28
Carrying out Network Ping Test
(ADVANCED[5]Network Ping Test) ...............29
Setting of Accept IP Address (ADVANCED
[6]Accept IP Addr(1) – [8]Accept IP Addr(3)) ...29
Accepting All IP Addresses
(ADVANCED[9]Accept All IP Addr) ...............29
Setting of Search Port
(ADVANCED[0]Search Port)..........................30
Return to Default Settings
(ADVANCED[!]Restore Default Setting) ........30
Return to Main Menu
(ADVANCED[Q]Return to Main Menu)..........30
Resetting the Lamp Timer of the Projector
via LAN ....................................................... 31
Troubleshooting.................................................. 33

-2
Connecting Pin Assignments
COMPUTER/COMPONENT input and COMPUTER/COMPONENT output Terminals: mini
D-sub 15 pin female connector
COMPUTER Input/Output COMPUTER Input/Output
Pin No. Signal Pin No. Signal
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
Video input (red)
Video input (green/sync on green)
Video input (bluea)
Not connected
Not connected
Earth (red)
Earth (green/sync on green)
Earth (blue)
Not connected
GND
Not connected
Bi-directional data
Horizontal sync signal: TTL level
Vertical sync signal: TTL level
Data clock
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
PR (CR)
Y
PB (CB)
Not connected
Not connected
Earth (PR)
Earth (Y)
Earth (PB)
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
HDMI Terminal
Pin No. Name Pin No. Name Pin No. Name
1.
2.
3.
4.
5.
6.
7.
T.M.D.S data 2+
T.M.D.S data 2 shield
T.M.D.S data 2–
T.M.D.S data 1+
T.M.D.S data 1 shield
T.M.D.S data 1–
T.M.D.S data 0+
8.
9.
10.
11.
12.
13.
T.M.D.S data 0 shield
T.M.D.S data 0–
T.M.D.S cl ock+
T.M.D.S clock shield
T.M.D.S cl ock–
CEC
14.
15.
16.
17.
18.
19.
Reserved
SCL
SDA
DDC/CEC ground
+5V power
Hot plug detection
5
10
15
1
11
6
5
10
15
1
11
6
119
218
119
218

-3
RS-232C Terminal: D-sub 9 pin male connector
Pin No. Signal Name I/O Reference
1.
2.
3.
4.
5.
6.
7.
8.
9.
RD
SD
SG
RS
CS
Receive Data
Send Data
Signal Ground
Request to Send
Clear to Send
Input
Output
Not connected
Connected to internal circuit
Connected to internal circuit
Not connected
Connected to internal circuit
Not connected
Connected to CS in internal circuit
Connected to RS in internal circuit
Not connected
RS-232C Cable recommended connection: D-sub 9 pin female connector
Pin No. Signal Pin No. Signal
1.
2.
3.
4.
5.
6.
7.
8.
9.
CD
RD
SD
ER
SG
DR
RS
CS
CI
1.
2.
3.
4.
5.
6.
7.
8.
9.
CD
RD
SD
ER
SG
DR
RS
CS
CI
Projector
Pin No.
Computer
Pin No.
4
5
6
4
5
6
USB Terminal: Type B USB connector LAN Terminal: LAN (RJ-45)
Pin No. Signal Name Pin No. Signal Pin No. Signal
1.
2.
3.
4.
VCC
USB–
USB+
SG
USB power
USB data–
USB data+
Signal Ground
1.
2.
3.
4.
TX+
TX–
RX+
5.
6.
7.
8.
RX–
15
69
15
69
51
96
51
96
Depending on the controlling device used, it may be necessary to connect Pin 4 and Pin 6 on the
controlling device (e.g. computer).
•
Note
Depending on the controlling device used, it may be necessary to connect Pin 4 and Pin 6 on the
controlling device (e.g. computer).
•
Note
43
12
43
12
8... 18 ... 1
Connecting Pin Assignments

-4
RS-232C Specifications and Commands
Computer control
A computer can be used to control the projector by connecting an RS-232C serial control cable (cross
type, commercially available) to the projector. (See page 24 of the projector's operation manual for
connection.)
Communication conditions
Set the serial port settings of the computer to match that of the table.
Signal format: Conforms to RS-232C standard. Parity bit: None
Baud rate*: 9,600 bps / 38,400 bps / 115,200 bps Stop bit: 1 bit
Data length: 8 bits Flow control: None
*Set the projector's baud rate to the same rate as used by the computer.
Basic format
Commands from the computer are sent in the following order: command, parameter, and return code.
After the projector processes the command from the computer, it sends a response code to the
computer.
Command format
C1 C2 C3 C4 P1 P2 P3 P4 Return code (0DH)
Command 4-digit Parameter 4-digit
Response code format
Normal response
Problem response (communication error or incorrect command)
OK Return code (0DH) E R R Return code (0DH)
Info
When controlling the projector using RS-232C commands from a computer, wait for at least 30 seconds
after the power has been turned on, and then transmit the commands.
After sending an input selection or picture adjustment command and then receiving an “OK” response
code, the projector may take some time to process the command. If a second command is sent while the
projector is still processing the first command, you may receive an “ERR” response code. If this happens,
try resending the second command.
When more than one code is being sent, send each command only after the response code for the
previous command from the projector is verified.
“POWR????”, “TABN _ _ _ 1”, “TLPS _ _ _ 1”, “TPOW _ _ _ 1”, “TLPN _ _ _ 1”, “TLTT _ _ _ 1”,
“TLTM _ _ _ 1”, “TLTL _ _ _ 1”, “TNAM _ _ _ 1”, “MNRD _ _ _ 1”, “PJN0 _ _ _ 1”
− When the projector receives the special commands shown above:
* The on-screen display will not disappear.
* The “Auto Power Off” timer will not be reset.
− The special commands are available for applications that require continuous polling.
•
•
•
•
If an underbar (_) appears in the parameter column, enter a space.
If an asterisk (*) appears in the parameter column, enter a value in the range indicated in brackets under
Control Contents.
•
•
Note
PJLinkTM Compliant:
This product conforms with the PJLink standard Class 1 and all Class 1 commands are implemented.
This product confirms with the PJLink standard specification version 1.00.
For additional information, visit “http://pjlink.jbmia.or.jp/english/”.

-5
Commands
Example: When turning on the projector, make the following setting.
Compuer Projector
POWR___1
o
m
OK
CONTROL CONTENTS COMMAND PARAMETER
RETURN
Power ON Standby mode
(or 30-second startup time)
Power On P O W R ___1 OK or ERR OK
Off P O W R ___0 OK OK or ERR
Status POWR????1 0
Projector Condition T A B N ___10:Normal
1: Temp High
8: Lamp Life 5% or less
16: Lamp Burn-out
32: Lamp Ignition Failure
0: Normal
1: Temp High
2: Fan Error
4: Cover Open
8: Lamp Life 5% or less
16: Lamp Burn-out
32: Lamp Ignition Failure
64:
Temp Abnormally High
Lamp Status T L P S ___1 0: Off, 1: On, 2: Retry
3: Waiting, 4: Lamp Error
0: Off, 4: Lamp Error
Power Status T P O W ___1 1: On, 2: Cooling 0: Standby
Quantity T L P N ___11
Usage Time(Hour) T L T T ___1 0 – 9999(Integer)
Usage Time(Minute) T L T M ___1 0, 15, 30, 45
Life(Percentage) TLTL___1 0% – 100%(Integer)
Name Model Name Check T N A M ___1PGD3750W
Model Name Check M N R D ___1PG-D3750W
Projector Name Setting 1
(First 4 characters) *1
PJN1****OKorERR
Projector Name Setting 2
(Middle 4 characters) *1
PJN2****OKorERR
Projector Name Setting 3
(Last 4 characters) *1
PJN3****OKorERR
Projector Name Check P J N 0 ___1ProjectorName
Input Change Computer1 I R G B ___1 OK or ERR ERR
Computer2 I R G B ___2 OK or ERR ERR
HDMI I R G B ___3 OK or ERR ERR
S-Video I V E D ___1 OK or ERR ERR
Video I V E D ___2 OK or ERR ERR
Input RGB Check I R G B ? ? ? ? 1: Computer1, 2: Computer2,
3: HDMI, ERR
ERR
Input Video Check I V E D ? ? ? ? 1: S-Video, 2: Video or ERR ERR
Input Mode Check I M O D ? ? ? ? 1: RGB, 2: Video ERR
Input Check I C H K ? ? ? ? 1: Computer1, 2: Computer2,
3: HDMI, 4: S-Video,
5: Video
ERR
Volume Volume(0 – 60) V O L A __**OKorERR ERR
Volume up/down(-10 – +10) V O U D _***OKorERR ERR
Keystone -80 – +80 K E Y S * * * * OK or ERR ERR
AV Mute On I M B K ___1 OK or ERR ERR
Off I M B K ___0 OK or ERR ERR
Freeze On F R E Z ___1 OK or ERR ERR
Off F R E Z ___0 OK or ERR ERR
Auto Sync Start A D J S ___1 OK or ERR ERR
Resize Computer1 Normal R A S R ___1 OK or ERR ERR
Stretch R A S R ___2 OK or ERR ERR
Dot By Dot R A S R ___3 OK or ERR ERR
Full R A S R ___5 OK or ERR ERR
Area Zoom R A S R __10OKorERR ERR
V-Stretch R A S R __11OKorERR ERR
Computer2 Normal R B S R ___1 OK or ERR ERR
Stretch R B S R ___2 OK or ERR ERR
Dot By Dot R B S R ___3 OK or ERR ERR
Full R B S R ___5 OK or ERR ERR
Area Zoom R B S R __10OKorERR ERR
V-Stretch R B S R __11OKorERR ERR
HDMI Normal R C S R ___1 OK or ERR ERR
Stretch R C S R ___2 OK or ERR ERR
Dot By Dot R C S R ___3 OK or ERR ERR
Full R C S R ___5 OK or ERR ERR
Area Zoom R C S R __10OKorERR ERR
V-Stretch R C S R __11OKorERR ERR
RS-232C Specifications and Commands

-6
CONTROL CONTENTS COMMAND PARAMETER
RETURN
Power ON Standby mode
(or 30-second startup time)
Resize S-Video Normal R A S V ___1 OK or ERR ERR
Stretch R A S V ___2 OK or ERR ERR
Area Zoom R A S V __10OKorERR ERR
V-Stretch R A S V __11OKorERR ERR
Video Normal R B S V ___1 OK or ERR ERR
Stretch R B S V ___2 OK or ERR ERR
Area Zoom R B S V __10OKorERR ERR
V-Stretch R B S V __11OKorERR ERR
ALL Reset ALRE___1 OK or ERR ERR
Computer1 INPUT Picture Mode Standard R A P S __10OKorERR ERR
Presentation RAPS__11OKorERR ERR
Movie RAPS__12OKorERR ERR
Game RAPS__13OKorERR ERR
sRGB RAPS__14OKorERR ERR
Contrast -30 – +30 R A P I _* * * OK or ERR ERR
Bright -30 – +30 R A B R _* * * OK or ERR ERR
Red -30 – +30 R A R D _* * * OK or ERR ERR
Blue -30 – +30 R A B E _* * * OK or ERR ERR
Color -30 – +30 R A C O _* * * OK or ERR ERR
Tint -30 – +30 R A T I _* * * OK or ERR ERR
Sharp -30 – +30 R A S H _* * * OK or ERR ERR
CLR Temp -1 – +1 R A C T __**OKorERR ERR
BrilliantColor™ 0 – +2 R A W E ___* OK or ERR ERR
Progressive 2D Progressive R A I P ___0 OK or ERR ERR
3D Progressive R A I P ___1 OK or ERR ERR
Film Mode RA I P___2OK or ERR ERR
DNR Off R A N R ___0 OK or ERR ERR
Level 1 R A N R ___1 OK or ERR ERR
Level 2 R A N R ___2 OK or ERR ERR
Picture Reset R A R E ___1 OK or ERR ERR
SignalType Auto IASI___0 OK or ERR ERR
RGB I A S I ___1 OK or ERR ERR
Component I A S I ___2 OK or ERR ERR
Audio Input Audio 1 R A A I ___1 OK or ERR ERR
Audio 2 R A A I ___2 OK or ERR ERR
Computer2 INPUT Picture Mode Standard R B P S __10OKorERR ERR
Presentation R B P S __11OKorERR ERR
Movie R B P S __12OKorERR ERR
Game R B P S __13OKorERR ERR
sRGB R B P S __14OKorERR ERR
Contrast -30 – +30 R B P I _* * * OK or ERR ERR
Bright -30–+30 RBBR_* * * OK or ERR ERR
Red -30 – +30 R B R D _* * * OK or ERR ERR
Blue -30 – +30 R B B E _* * * OK or ERR ERR
Color -30 – +30 R B C O _* * * OK or ERR ERR
Tint -30 – +30 R B T I _* * * OK or ERR ERR
Sharp -30 – +30 R B S H _* * * OK or ERR ERR
CLR Temp -1 – +1 R B C T __**OKorERR ERR
BrilliantColor™ 0 – +2 R B W E ___* OK or ERR ERR
Progressive 2D Progressive R B I P ___0 OK or ERR ERR
3D Progressive R B I P ___1 OK or ERR ERR
Film Mode R B I P ___2 OK or ERR ERR
DNR Off R B N R ___0 OK or ERR ERR
Level 1 R B N R ___1 OK or ERR ERR
Level 2 R B N R ___2 OK or ERR ERR
PictureReset RBRE ___1 OK or ERR ERR
Signal Type Auto I B S I ___0 OK or ERR ERR
RGB I B S I ___1 OK or ERR ERR
Component I B S I ___2 OK or ERR ERR
Audio Input Audio 1 R B A I ___1 OK or ERR ERR
Audio 2 R B A I ___2 OK or ERR ERR
RS-232C Specifications and Commands

-7
CONTROL CONTENTS COMMAND PARAMETER
RETURN
Power ON Standby mode
(or 30-second startup time)
HDMI INPUT Picture Mode Standard R C P S __10OKorERR ERR
Presentation R C P S __11OKorERR ERR
Movie R C P S __12OKorERR ERR
Game R C P S __13OKorERR ERR
sRGB R C P S __14OKorERR ERR
Contrast -30 – +30 R C P I _***OKorERR ERR
Bright -30 – +30 R C B R _***OKorERR ERR
Red -30 – +30 R C R D _***OKorERR ERR
Blue -30 – +30 R C B E _***OKorERR ERR
Color -30 – +30 R C C O _***OKorERR ERR
Tint -30 – +30 R C T I _***OKorERR ERR
Sharp -30 – +30 R C S H _***OKorERR ERR
CLR Temp -1 – +1 R C C T __**OKorERR ERR
BrilliantColor™ 0 – +2 R C W E ___* OK or ERR ERR
DNR Off R C N R ___0 OK or ERR ERR
Level 1 R C N R ___1 OK or ERR ERR
Level 2 R C N R ___2 OK or ERR ERR
Picture Reset R C R E ___1 OK or ERR ERR
Signal Type Auto I C S I ___0 OK or ERR ERR
RGB I C S I ___1 OK or ERR ERR
Component I C S I ___2 OK or ERR ERR
Audio Input Audio 1 R C A I ___1 OK or ERR ERR
Audio 2 R C A I ___2 OK or ERR ERR
HDMI R C A I ___3 OK or ERR ERR
Dynamic
Range
Auto H M C D ___0 OK or ERR ERR
Standard H M C D ___1 OK or ERR ERR
Enhanced H M C D ___2 OK or ERR ERR
S-Video INPUT Picture Mode Standard V A P S __10OKorERR ERR
Presentation VAPS__11OKorERR ERR
Movie VAPS__12OKorERR ERR
Game VAPS__13OKorERR ERR
Contrast -30 – +30 V A P I _***OKorERR ERR
Bright -30 – +30 V A B R _***OKorERR ERR
Red -30 – +30 V A R D _***OKorERR ERR
Blue -30 – +30 V A B E _***OKorERR ERR
Color -30 – +30 V A C O _***OKorERR ERR
Tint -30 – +30 V A T I _***OKorERR ERR
Sharp -30 – +30 V A S H _***OKorERR ERR
CLR Temp -1 – +1 V A C T __**OKorERR ERR
BrilliantColor™ 0 – +2 V A W E ___* OK or ERR ERR
Progressive 2D Progressive V A I P ___0 OK or ERR ERR
3D Progressive V A I P ___1 OK or ERR ERR
Film Mode V A I P ___2 OK or ERR ERR
DNR Off V A N R ___0 OK or ERR ERR
Level 1 V A N R ___1 OK or ERR ERR
Level 2 V A N R ___2 OK or ERR ERR
Picture Reset V A R E ___1 OK or ERR ERR
Audio Input Audio 1 V A A I ___1 OK or ERR ERR
Audio 2 V A A I ___2 OK or ERR ERR
RS-232C Specifications and Commands

-8
CONTROL CONTENTS COMMAND PARAMETER
RETURN
Power ON Standby mode
(or 30-second startup time)
Video INPUT Picture Mode Standard V B P S __10OKorERR ERR
Presentation V B P S __11OKorERR ERR
Movie V B P S __12OKorERR ERR
Game V B P S __13OKorERR ERR
Contrast -30 – +30 V B P I _* * * OK or ERR ERR
Bright -30 – +30 V B B R _* * * OK or ERR ERR
Red -30 – +30 V B R D _* * * OK or ERR ERR
Blue -30 – +30 V B B E _* * * OK or ERR ERR
Color -30 – +30 V B C O _* * * OK or ERR ERR
Tint -30 – +30 V B T I _* * * OK or ERR ERR
Sharp -30 – +30 V B S H _* * * OK or ERR ERR
CLR Temp -1 – +1 V B C T __**OKorERR ERR
BrilliantColor™ 0 – +2 V B W E ___* OK or ERR ERR
Progressive 2D Progressive V B I P ___0 OK or ERR ERR
3D Progressive V B I P ___1 OK or ERR ERR
Film Mode V B I P ___2 OK or ERR ERR
DNR Off V B N R ___0 OK or ERR ERR
Level 1 V B N R ___1 OK or ERR ERR
Level 2 V B N R ___2 OK or ERR ERR
Picture Reset V B R E ___1 OK or ERR ERR
Audio Input Audio 1 V B A I ___1 OK or ERR ERR
Audio 2 V B A I ___2 OK or ERR ERR
C.M.S. Setting On C M C S __11OKorERR ERR
Off C M C S __00OKorERR ERR
C.M.S. Hue Red C M H R _* * * OK or ERR ERR
Yellow C M H Y _* * * OK or ERR ERR
Green C M H G _* * * OK or ERR ERR
Cyan C M H C _* * * OK or ERR ERR
Blue C M H B _* * * OK or ERR ERR
Magenta C M H M _* * * OK or ERR ERR
Reset C M R E ___2 OK or ERR ERR
Saturation Red C M S R _* * * OK or ERR ERR
Yellow C M S Y _* * * OK or ERR ERR
Green C M S G _* * * OK or ERR ERR
Cyan C M S C _* * * OK or ERR ERR
Blue C M S B _* * * OK or ERR ERR
Magenta C M S M _* * * OK or ERR ERR
Reset C M R E ___3 OK or ERR ERR
Value Red C M V R _* * * OK or ERR ERR
Yellow C M V Y _* * * OK or ERR ERR
Green C M V G _* * * OK or ERR ERR
Cyan C M V C _* * * OK or ERR ERR
Blue C M V B _* * * OK or ERR ERR
Magenta C M V M _* * * OK or ERR ERR
Reset C M R E ___4 OK or ERR ERR
C.M.S. All Reset C M R E ___1 OK or ERR ERR
Clock -150 – +150 I N C L * * * * OK or ERR ERR
Phase -30 – +30 I N P H _* * * OK or ERR ERR
H-position -150–+150 IAHP****OKorERR ERR
V-position -60 – +60 I A V P _* * * OK or ERR ERR
Fine Sync Adjustment Reset I A R E ___1 OK or ERR ERR
Image Shift -40 – +40 L N D S _***OKorERR ERR
Overscan On O V S N ___1 OK or ERR ERR
Off O V S N ___0 OK or ERR ERR
OSD Display On I M D I ___1 OK or ERR ERR
Off I M D I ___0 OK or ERR ERR
Video System Auto M E S Y ___1 OK or ERR ERR
PAL M E S Y ___2 OK or ERR ERR
SECAM M E S Y ___3 OK or ERR ERR
NTSC4.43 M E S Y ___4 OK or ERR ERR
NTSC3.58 M E S Y ___5 OK or ERR ERR
PAL-M M E S Y ___6 OK or ERR ERR
PAL-N M E S Y ___7 OK or ERR ERR
PAL-60 M E S Y ___8 OK or ERR ERR
RS-232C Specifications and Commands

-9
CONTROL CONTENTS COMMAND PARAMETER
RETURN
Power ON Standby mode
(or 30-second startup time)
Background Logo I M B G ___1 OK or ERR ERR
Blue I M B G ___3 OK or ERR ERR
None I M B G ___4 OK or ERR ERR
Eco+Quiet On T H M D ___1 OK or ERR ERR
Off T H M D ___0 OK or ERR ERR
Auto Sync On A A D J ___1 OK or ERR ERR
Off A A D J ___0 OK or ERR ERR
Auto Power Off On A P O W ___1 OK or ERR ERR
Off A P O W ___0 OK or ERR ERR
Auto Restart On A R E S ___1 OK or ERR ERR
Off A R E S ___0 OK or ERR ERR
STANDBY Mode Standard M O U T ___1 OK or ERR ERR
Eco M O U T ___0 OK or ERR ERR
PRJ Mode Reverse On I M R E ___1 OK or ERR ERR
Off I M R E ___0 OK or ERR ERR
Invert On I M I N ___1 OK or ERR ERR
Off I M I N ___0 OK or ERR ERR
Language English M E L A ___1 OK or ERR ERR
Deutsch M E L A ___2 OK or ERR ERR
Español M E L A ___3 OK or ERR ERR
Nederlands M E L A ___4 OK or ERR ERR
Français M E L A ___5 OK or ERR ERR
Italiano M E L A ___6 OK or ERR ERR
Svenska M E L A ___7 OK or ERR ERR
ME L A ___8 OK or ERR ERR
Português M E L A ___9 OK or ERR ERR
ME L A __10OKorERR ERR
ME L A __11OKorERR ERR
ME L A __12OKorERR ERR
ME L A __13OKorERR ERR
polski M E L A __14OKorERR ERR
Türkçe M E L A __15OKorERR ERR
ME L A __16OKorERR ERR
Magyar M E L A __17OKorERR ERR
System Sound On S S N D ___1 OK or ERR ERR
Off S S N D ___0 OK or ERR ERR
Audio Out FAO A O U T ___1 OK or ERR ERR
VAO A O U T ___2 OK or ERR ERR
InternalSpeaker On ASPK___1 OK or ERR ERR
Off ASPK___0 OK or ERR ERR
RGB Frequency Check Horizontal T F R Q ___1 kHz(***.* or ERR) ERR
Vertical T F R Q ___2 Hz(***.* or ERR) ERR
Fan Mode Normal H L M D ___0 OK or ERR ERR
High H L M D ___1 OK or ERR ERR
Balance -30 − +30 A A B L _***OKorERR ERR
Treble -30 − +30 A A T E _***OKorERR ERR
Bass -30 − +30 A A B A _***OKorERR ERR
Audio Adjustment Reset A A R E ___1 OK or ERR ERR
LampTimerReset*3 LPRE0001ERR OKorERR
*1 For setting the projector name, send the commands in the order of PJN1, PJN2 and PJN3.
*2 This command should be sent only after the “IRGB _ _ _ 2” command is sent and an “OK” response code is
received.
*3 The Lamp Timer Reset command is available only in standby mode.
RS-232C Specifications and Commands

-10
This section describes the basic procedure for using the projector via the network.
If the network is already constructed, the projector's network settings may need to be changed. Please
consult your network administrator for assistance with these settings.
You can make network settings both on the projector and on the computer. The following procedure is
for making settings on the computer.
Network settings on the computer
Connect a LAN cable (Category 5, cross-over type) between the computer and projector.
LAN cable
(commercially available)
1. Connecting the projector to a computer
Page 11
Adjust the IP settings of the computer to enable one-to-one communications with the projector.
Temporarily change
the computer's IP
address.
2. Setting an IP address for the computer
Pages 12, 13
Adjust the projector network settings to conform to your network.
Use Internet Explorer
(version 5.0 or later)
to make various
projector settings.
3. Setting up a network connection for the projector
Page 14
Microsoft®, Windows®and Windows Vista®are registered trademarks of Microsoft Corporation in the
United States and/or other countries.
PJLink is a registered trademark or an application trademark in Japan, the United States and/or other
countries/regions.
All other company or product names are trademarks or registered trademarks of their respective
companies.
•
•
•
Setting up the Projector Network Environment