Panasonic PT-CX200 System manual

SPEC FILE
Product Number : PT-CX200
Product Name : Ultra Short-Throw DLP ™Projector
As of No ember 2012. Specifications and appearance are subject to change without notice.
SFD12M002-1
1/13

SPEC FI L E
PT-CX200
Ultra Short-Throw DLP™Projector
As of November 2012
SFD12M002-1
2/13
Specifications
Main unit
Power supply
Power consumption
DLP™ chip Panel size
Display method
Pixels
Lens
Lamp
Screen size
Colors
Brightness*2
Center-to-corner uniformity*2
Contrast*2
Resolution
Scanning frequency DMI
RGB
YPBPR(YCBCR)
Video/S-Video
Keystone correction range
Installation
Built-in speaker Size
Output power
Terminals DMI IN
COMPUTER (RGB) 1 IN
R, G, B
Y, PB(CB), PR(CR)
COMPUTER (RGB) 2 IN / 1 OUT
R, G, B
VIDEO IN
S-VIDEO IN
100–240 V AC, 50/60 z
350 W
(0.45 W when STANDBY MODE set to ECO,*111.0 W when STANDBY MODE
set to NETWORK.)
14.0 mm (0.55 inches) diagonal (4:3 aspect ratio)
DLP™ chip × 1, DLP™ system
786,432 (1,024 × 768) pixels
Fixed (0.24:1 throw ratio), manual focus, F 2.5, f 4.83 mm
275 W U M lamp ×1
1.40 – 2.29 m (55 – 90 inches) diagonally, 4:3 aspect ratio
Full color (16,777,216 colors)
2,000 lumens (LAMP POWER: NORMAL)
80%
2,000:1 (full on/off, LAMP POWER: NORMAL)
1,024 × 768 pixels (Input signals that exceed this resolution will be
converted to 1,024 × 768 pixels.)
f: 15 k z–93 k z, fV: 50 z–120 z,
dot clock: 150 M z or lower
f: 15 k z–93 k z, fV: 50 z–120 z, dot clock: 150 M z or lower
(Signals above 150 M z are downsampled.)
525i (480i): f 15.75 k z; fV60 z,
625i (576i): f 15.63 k z; fV50 z,
525p (480p): f 31.50 k z; fV60 z,
625p (576p): f 31.25 k z; fV50 z,
750 (720)/60p: f 45.00 k z; fV60 z,
750 (720)/50p: f 37.50 k z; fV50 z,
1125 (1080)/60i: f 33.75 k z; fV60 z,
1125 (1080)/50i: f 28.13 k z; fV50 z
f: 15.75 k z, fV: 60 z [NTSC/NTSC4.43/PAL-M/PAL60]
f: 15.63 k z, fV: 50 z [PAL/PAL-N/SECAM]
Vertical: ±5°
Ceiling/floor, front/rear (menu selection)
3.7 cm (1-15/32 inches) (round) ×1
10 W (monaural)
DMI 19-pin × 1, DCP compatible
525p (480p), 625p (576p), 750 (720)/60p, 750 (720)/50p,
1125 (1080)/60i, 1125 (1080)/50i, 1125 (1080)/60p, 1125 (1080)/50p
VGA (640 × 480) – WSXGA+(1,680 × 1,050), Audio signal: linear
PCM (sampling frequencies: 48 k z, 44.1 k z, 32 k z)
D-sub D 15-pin (female) ×1
G: 0.7 Vp-p (1.0 Vp-p for sync on G), 75 ohms;
B, R: 0.7 Vp-p, 75 ohms;
D/VD, SYNC: high impedance, TTL (positive/negative)
Y: 1.0 Vp-p (including sync signal);
PB(CB), PR(CR): 0.7 Vp-p, 75 ohms
D-sub D 15-pin (female) × 1
(input/output selectable using on-screen menu)
G: 0.7 Vp-p (1.0 Vp-p for sync on G), 75 ohms;
B, R: 0.7 Vp-p, 75 ohms;
D/VD, SYNC: high impedance, TTL (positive/negative)
RCA pin × 1, 1.0 Vp-p, 75 ohms
Mini DIN 4-pin × 1, Y: 1.0 Vp-p; C: 0.286 Vp-p, 75 ohms

SPEC FI L E
PT-CX200
Ultra Short-Throw DLP™Projector
As of November 2012
SFD12M002-1
3/13
COMPUTER 1 AUDIO IN
COMPUTER 2 AUDIO IN
VIDEO/S-VIDEO AUDIO IN
AUDIO OUT
SERIAL IN
LAN
3D SYNC OUT
Power cord length
Cabinet materials
Dimensions (W × ×D)
Weight
Operation noise
Operating temperature
Operating humidity
Remote control unit
Power supply
Operation range*4
Dimensions (W × × D)
Weight
Supplied accessories
Optional accessories
Ceiling mount bracket
Bracket assembly
Wall mount bracket
Replacement lamp unit
Replacement filter unit
M3 (L, R) × 1, 0.5 Vrms
M3 (L, R) × 1, 0.5 Vrms
RCA × 2 (L/R × 1), 0.5 Vrms
M3 (L, R) × 1 (monitor out: 0–2.0 Vrms, variable)
D-sub 9-pin (female) × 1, for external control (RS-232C compliant)
RJ-45 × 1, for network connection, 100Base-TX/10Base-T, compliant
with PJLink™
Mini DIN 3-pin × 1, for 3D transmitter connection
3.0 m (9 ft 10 in)
Molded plastic (PC)
321 mm × 178 mm*3× 386 mm
(12-5/8 × 7*3× 15-3/16 inches)
Approximately 6.2 kg (13.7 lbs)
36 dB (LAMP POWER: NORMAL), 28 dB (LAMP POWER: ECO)
0–40 °C (32–104 °F) up to 1,000 m (3,281 ft) above sea level,
0–30 °C (32–86 °F) between 1,000 m and 2,700 m (3,281 ft and
8,858 ft) above sea level.
20%–80% (no condensation)
3 V DC (R03/LR03/AAA type battery × 2)
Approximately 5 m (16.4 ft) when operated from directly in front of the
signal receptor
52 × 110 × 18 mm (2-1/16 × 4-11/32 × 23/32 inches)
Approx. 67 g (2.4 oz) (including batteries)
Power cord with security lock (× 1) (× 2 for PT-CX200EA)
Wireless remote control unit (× 1)
Batteries for remote control (R03/LR03/AAA type × 2)
Computer cable (for VGA, 1.8 m / 5 ft 11 in) (× 1)
ET-PKV100 (for high ceilings)
ET-PKV100S (for low ceilings)
ET-PKC100B
ET-PKC100W
ET-LAC100
ET-RFC100
Weights and dimensions shown are approximate. Specifications subject to change without notice.
*1 When the standby mode is set to eco, network functions such as power on over the LAN network will not operate. Also, only certain com-
mands can be received for external control using the serial terminal.
*2 Measurement, measuring conditions, and method of notation all comply with ISO 21118 international standards.
*3 With legs at shortest position.
*4 Operation range differs depending on environments.

170
( 6 -11/ 16 ) )
8
(5/16)
178
(7)
77.5
(3-1/16)
385
(15-5/32)
386
(15-3/16)
321
(12-5/8)
296
(11-21/32)
Dimensions
unit : mm (inch)
NOTE: This illustration is not drawn to scale.
SPEC FI L E
PT-CX200
Ultra Short-Throw DLP™Projector
As of November 2012
SFD12M002-1
4/13
Terminals
1234
9101112
67 8
5
1 Video input
2 S-Video input
3 Audio input for video/S-Video
4 Audio input for computer 1
5 Audio input for computer 2
6 Audio output
7 Serial input
8 3D sync output
9 LAN connector
10 Computer 1 input
11 Computer 2 input / computer 1 output
12 DMI input

SPEC FI L E
PT-CX200
Ultra Short-Throw DLP™Projector
As of November 2012
SFD12M002-1
5/13
Standard setting-up position
Projected image
Projected image
Lower edge of projected image
Upper edge of projected image
∅38 (1-1/2)
100
(3-15/16)
100
(3-15/16)
200
(7-7/8)
70
(2-3/4)
140
(5-1/2)
70 (2-3/4)
77.5 (3-1/16)
177209
(6-31/32)(8-7/32)
A
A
B
B
E
F
E
F
1045–1615
(41-5/32–63-19/32)
Adjustable in
30-mm
(1-3/16-inch) step.
unit : mm (inch)
NOTE:
Illustrations show the projector
installed using optional ceiling mount
bracket ET- KV100H and bracket
assembly ET- KC100B.
This illustration is not drawn to scale.
55
60
70
80
90
Screen size
(inch, diagonal) A: Distance from the edge
of the projection window
to the screen
B: Distance from the
projector front
to the screen
E: Height from the edge of
the screen to the
top of the projector
F: Height from the edge of
the screen to the
bottom of the projector
-0.05
-0.02
0.04
0.09
0.14
0.25
0.28
0.33
0.38
0.44
0.25
0.27
0.29
0.32
0.35
0.07
0.09
0.11
0.14
0.17
rojection distance for 4:3 aspect ratio screen
Unit: meters

SPEC FI L E
PT-CX200
Ultra Short-Throw DLP™Projector
As of November 2012
SFD12M002-1
6/13
Calculation of the projection distance
For a screen size different from the above, use the equation below to calculate the projection distance.
Aspect ratio 4:3
A (m) = (diagonal screen size in inches) × 0.0053135 – 0.041703
NOTE:
Distances calculated with the above equations will include a slight error.
55
60
70
80
90
Screen size
(inch, diagonal) A: Distance from the edge
of the projection window
to the screen
B: Distance from the
projector front
to the screen
E: Height from the edge of
the screen to the
top of the projector
F: Height from the edge of
the screen to the
bottom of the projector
-0.2
-0.1
0.1
0.3
0.5
0.8
0.9
1.1
1.3
1.4
0.8
0.9
1.0
1.0
1.2
0.2
0.3
0.4
0.5
0.6
rojection distance for 4:3 aspect ratio screen
Unit: feet

SPEC FI L E
PT-CX200
Ultra Short-Throw DLP™Projector
As of November 2012
SFD12M002-1
7/13
+10°
-10°
+10°
-10°
+10° -10°
+10° -10°
+10°
-10°
Installable angle
Install the projector at an angle within the range shown below.
• Vertical direction
The projector may be installed at a vertical angle shown here .
• Horizontal direction
The projector may be installed at a horizontal angle of ±10°.

SPEC FI L E
PT-CX200
Ultra Short-Throw DLP™Projector
As of November 2012
SFD12M002-1
8/13
List of compatible signals
The signals that can be input to this projector are shown in the table below. orizontal scanning fre-
quencies of 15 k z to 93 k z, vertical scanning frequencies of 50 z to 120 z, and a dot clock of
150 M z maximum can be input. (RGB signals exceeding the dot clock rate of 150M z are downsam-
pled.)
NOTE: The native resolution of this projector is 1,024 × 768 pixels. If the display resolution of the input signal is different from the
native resolution, image compression or expansion will be used to convert the input signal to a level within the native resolution.
Display mode Display
resolution
(dots)1
Scanning frequency
H
(kHz)
V
(kHz)
Dot clock
frequency
(MHz)
Format 3D-ready
720 × 480i
720 × 576i
640 × 480i
768 × 576i
640 × 480
768 × 575
1280 × 720
1920 × 1080i
1920 × 1080
640 × 400
640 × 480
720 × 400
640 × 480
800 × 600
832 × 624
15.7
15.6
15.7
15.7
31.5
15.6
15.6
31.3
31.5
31.5
62.9
31.3
62.5
45.0
90.0
37.5
75.0
33.8
67.5
28.1
56.3
27.0
28.1
33.8
67.5
56.3
31.5
31.5
31.5
37.5
37.9
37.9
43.3
31.5
35.0
35.0
32.7
34.5
35.2
37.9
37.9
38.0
38.6
46.9
48.1
53.7
76.3
49.7
59.9
50.0
59.9
59.9
119.9
50.0
50.0
100.0
59.9
59.9
119.9
50.0
100.0
60.0
120.0
50.0
100.0
60.0
120.0
50.0
100.0
24.0
25.0
30.0
60.0
50.0
70.1
59.9
59.9
75.0
72.8
74.4
85.0
70.1
66.6
66.7
51.1
55.4
56.3
60.3
61.0
60.5
60.3
75.0
72.2
85.1
120.0
74.6
–
–
12.3
–
–
14.8
–
–
25.2
27.0
54.0
29.5
54.0
74.3
148.5
74.3
148.5
74.3
148.5
74.3
74.3
74.3
148.5
148.5
74.3
148.5
25.2
25.2
25.2
31.5
31.5
31.5
36.0
28.3
31.3
30.2
32.7
36.4
36.0
40.0
40.0
40.1
38.6
49.5
50.0
56.3
73.3
57.3
NTSC/NTSC4.43/PAL-M/PAL60
PAL/PAL-N/SECAM
525i (480i)
625i (576i)
525p (480p)
625p (576p)
720/60p
720/50p
1080/60i
1080/50i
1080/24p
1080/25p
1080/30p
1080/60p
1080/50p
VGA
MAC LC13
MAC13
SVGA
MAC16
VIDEO/S-VIDEO
YPBPR/RGB
HDMI
YPBPR/RGB
HDMI
YPBPR/RGB
HDMI
HDMI/YPBPR/RGB
HDMI
HDMI/YPBPR/RGB
HDMI
HDMI/YPBPR/RGB
HDMI
HDMI/YPBPR/RGB
HDMI
HDMI/YPBPR/RGB
HDMI
HDMI/YPBPR/RGB
RGB
HDMI
RGB
HDMI/RGB
RGB
HDMI/RGB
RGB
Yes
No
Yes
No
Yes
YPBPRonly
Yes
HDMI/YPBPRonly
Yes
HDMI/YPBPRonly
Yes
HDMI/YPBPRonly
Yes
HDMI/YPBPRonly
Yes
HDMI/YPBPRonly
Yes
No
Yes
No
Yes
No
Yes
No
*1 The “i” appearing after the resolution indicates an interlaced signal.

SPEC FI L E
PT-CX200
Ultra Short-Throw DLP™Projector
As of November 2012
SFD12M002-1
9/13
Display mode Display
resolution
(dots)1
Scanning frequency
H
(kHz)
V
(kHz)
Dot clock
frequency
(MHz)
Format 3D-ready
1024 × 768
1280 × 768
1280 × 800
1360 × 768
1376 × 768
1152 × 870
1152 × 864
1152 × 900
1280 × 960
1280 × 1024
1400 × 1050
1440 × 900
1600 × 1200
1680 × 1050
1920 × 1200
43.4
44.0
46.9
47.0
48.4
48.5
56.5
58.0
60.0
60.3
61.0
62.0
63.5
68.7
97.6
60.2
47.8
60.3
68.6
97.4
41.2
49.6
49.7
101.6
97.5
48.4
68.7
64.2
61.2
71.4
61.9
60.0
60.3
62.5
63.3
63.4
63.7
63.8
63.9
64.0
71.7
77.0
80.0
81.1
91.1
80.0
62.5
64.0
64.0
64.7
65.1
65.3
65.4
55.9
75.0
81.3
87.5
93.8
106.3
65.3
74.0
74.6
60.0
54.6
58.2
58.3
60.0
60.0
70.1
72.0
75.0
74.9
75.7
77.1
79.4
85.0
120.0
75.1
59.9
74.9
84.8
119.8
50.0
60.1
59.8
119.9
120.0
60.0
75.1
70.4
65.2
75.6
66.0
60.0
58.1
58.6
60.0
60.0
60.0
60.2
60.0
60.0
67.2
72.0
75.0
76.1
85.0
75.1
58.6
60.0
60.2
59.9
59.9
60.0
60.1
59.9
60.0
65.0
70.0
75.0
85.0
60.0
60.0
59.9
65.0
59.1
63.0
61.7
65.0
65.2
75.0
74.7
78.8
79.3
81.0
84.4
83.4
94.5
115.5
80.0
79.5
102.3
117.5
140.3
68.6
79.4
83.5
140.3
148.3
86.7
100.0
94.6
92.0
105.1
94.5
108.0
93.1
108.0
108.2
111.5
109.5
108.2
107.4
108.0
117.0
130.1
135.0
135.0
157.5
135.2
108.0
108.2
108.0
101.0
122.4
121.8
122.9
106.5
162.0
175.5
189.0
202.5
229.5
146.3
154.0
193.3
XGA
MAC19
WXGA
MAC21
SXGA
MAC
SXGA+
WXGA+
UXGA
WSXGA+
WUXGA
HDMI
RGB
HDMI/RGB
RGB
HDMI/RGB
RGB
HDMI
RGB
HDMI/RGB
RGB
HDMI/RGB
RGB
HDMI/RGB
RGB
HDMI/RGB
RGB
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
RGB only
Yes
RGB only
Yes
No
Yes
No

SPEC FI L E
PT-CX200
Ultra Short-Throw DLP™Projector
As of November 2012
SFD12M002-1
10/13
Serial connector
The serial connector complies with RS-232C. To control the projector from a personal computer, com-
mands must be input through communication software, based on the format and satisfying the commu-
nication conditions shown below.
Basic format
Send transmissions from the computer in the following order: command, carriage return (CR).
• Control command • Status request command
in assignments and signal names
5
96
1
D-sub 9-pin (female)
Serial input
Description
NC
Send data
Receive data
NC
Ground
Signal name
–
TXD
RXD
–
GND
No.
1
2
3
4
5
Description
NC
Connected internally
Connected internally
NC
Signal name
–
CTS
RTS
–
No.
6
7
8
9
CAUTION
• It may not be possible to send or receive commands for about 10 to 60 seconds when the lamp is first turned on. If this occurs, wait for 60 sec-
onds, then try sending or receiving again.
• When sending multiple commands, be sure to wait for at least 0.5 second after receiving a response from the projector before sending the next
command.
• Additional time is sometimes required for response due to processing inside the projector. Set the time-out period for command response to 10
seconds or more.
End
(1 byte)
Command
(3 bytes)
[CR]CN1 N2
End
(1 byte)
Command
(3 bytes)
[CR]CRN
Communication conditions (factory setting)
Signal level
Synchronization method
Baud rate
Parity
Character length
Stop bit
X parameter
S parameter
RS-232C-compliant
Start-stop synchronization
19,200 bps
None
8 bits
1 bit
None
None