Martin MAC III Quadray Module Use and maintenance manual

Martin MAC III™ Quadray Module Installation and DMX Control Guide 1
MAC III Quadray Module™
Installation and Control Guide
Introduction
This Guide explains how to install the Martin MAC III Quadray Module™, P/N 91614042, on a Martin
MAC III AirFX™ fixture and control the Quadray functions via DMX.
Installation takes only a few minutes. If you keep the standard components you remove when you install
the Quadray module, the Quadray components can be uninstalled and the fixture returned to standard
configuration at any time.
Warning! Follow all the safety precautions in the MAC III AirFX user manual and use the manual
for reference when installing the Quadray Module and using the modified product. The user
manual is supplied with fixtures, but check that you have the latest revision of the user manual.
This is available for download from the Product Support page for the MAC III AirFX at
www.martin.com
Warning! Disconnect the fixture from power and allow to cool for at least 2 hours and 45
minutes before starting work.
Warning! The Quadray Module must be installed by qualified professional technicians only.
Read all of this Installation Guide carefully before starting to install the module.
Important! Make sure that the front of the head does not face the sun or any other strong light
source directly for longer than a few seconds at any time. The lens can focus the sun's rays
inside the fixture, causing internal damage and creating a possible fire risk
Important! Do not use concentrated alcohol solutions, abrasive products or solvents to clean
the components in the Quadray Module. If wiping with a soft, lint-free cloth dampened with
distilled water is not effective, damp the cloth with distilled water containing 20% isopropyl
alcohol in solution.
If you have any questions about how to install the Quadray Module or use it safely, please contact your
local Martin distributor (see www.martin.com/distributors for details) or call the Martin 24-hour service
hotline on [phone], or in the USA on 1-888-tech-180.
Software compatibility
MAC III AirFX firmware version 1.3 or later is required for operation with the Quadray Module. The
latest version of the MAC III AirFX firmware is available for download from the MAC III AirFX Product
Support page on the Martin™ website at www.martin.com
© 2013 Martin Professional A/S. Olof Palmes Allé 18, DK-8200 Aarhus N, Denmark. Information subject to change without notice. Martin
Professional A/S and all affiliated companies disclaim liability for any injury, damage, direct or indirect loss, consequential or economic
loss or any other loss occasioned by the use of, inability to use or reliance on the information contained in this installation note. The
Martin logo, the Martin name and all other trademarks in this document pertaining to services or products by Martin Professional A/S or
its affiliates and subsidiaries are trademarks owned or licensed by Martin Professional A/S or its affiliates or subsidiaries.
P/N 35000630 Rev. A

Martin MAC III™ Quadray Module Installation and DMX Control Guide 2
Overview
The Quadray Module accessory contains the following items:
• MAC III Quadray Module
• MAC III Quadray Module wireset
• This Installation Guide
Keep the protective packaging supplied with the module for possible re-use.
Installation procedure
To install the Quadray Module on a standard Martin MAC III AirFX
fixture:
1. Disconnect the fixture from power and allow it to cool for at least
2 hours and 45 minutes.
2. Place the fixture on a secure work surface. See Figure 1. Tilt the
head vertically upwards and apply the tilt lock.
3. See Figure 2. Remove the top
head cover by releasing the
cover retaining screws and
unclipping the cover safety wire
carabiner (the top of the head is
above the text printed on the
back of the fixture with the text
facing the right way up).
4. See Figure 3. Release the four screws (arrowed)
from the front lens assembly, then release the front
lens safety attachment. Remove the front lens
assembly and store it for possible re-use if the
fixture is to be returned to standard configuration at
a later time.
5. With the top of the fixture facing you, unclip the air
filter from the right-hand side of the head as
described in the MAC III AirFX user manual.
Figure 1
Figure 2
Figure 3

Martin MAC III™ Quadray Module Installation and DMX Control Guide 3
6. See Figure 4. Line up the Quadray Module so that the PCB in the Module is on the right-hand side
of the head, where you have removed the air filter. Hold the Quadray Module up to the head and
attach the module’s safety wire as shown. Make sure that the safety wire is securely fastened in the
head.
7. See Figure 5. Fasten the Quadray Module
securely onto the front of the head with its four
screws.
Figure 4
Figure 5

Martin MAC III™ Quadray Module Installation and DMX Control Guide 4
8. See Figure 6. Route the Quadray Module’s
wireset through the head chassis as
shown. The connectors at each end are
identical, so it does not matter which way
round you install the wireset.
9. See Figure 7. Connect the module end of
the wireset to the PCB in the Quadray
Module as follows: power to connector
PL18 and data to connector PL12.
Figure 6
Figure 7

Martin MAC III™ Quadray Module Installation and DMX Control Guide 5
10. See Figure 8. Connect the other end of the wireset to the PCB shown in the head as follows: power
to connector PL13 and data to connector PL3.
11. Reinstall the air filter and head covers, attaching safety wires securely.
12. Release the tilt lock before reapplying power.
13. Finally, check and if necessary adjust the lamp alignment as described in the MAC III AirFX user
manual.
Figure 8

Martin MAC III™ Quadray Module Installation and DMX Control Guide 6
Quadray control
When the Quadray Module is installed and the fixture is powered on, the MAC III AirFX recognizes the
new module automatically and configures itself for operation with the module.
If you remove the Quadray Module in the future and reinstall the standard components, the fixture will
recognize that no module is present and reconfigure itself for operation without the module.
DMX Control
With the Quadray Module installed, five extra DMX channels become available after the 22 channels in
the standard fixture. These channels give the DMX control functions shown in the following table:
Channel Value Function
Fade
Status
Default
Value
23
0 - 40
41 - 80
81 - 100
101 - 130
131 - 180
181 - 183
184 - 255
Quadray overall control
Indexing
Rotation
No function
FX selection (see Table 2)
Positions
Continuous FX
Static FX
No function
Snap 101
24
0 - 255
0 - 2
3 - 126
127 - 129
130 - 253
254 - 255
0 - 255
0 - 2
3 - 126
127 - 129
130 - 253
254 - 255
0 - 255
Ray 1 Indexing
Indexing 0° - 360°
Ray 1 Rotation
No rotation
Rotating CW Fast CW Slow
No rotation
Rotating CCW Slow CCW Fast
No rotation
FX position fade time*
0 sec. - 10 sec.
Continuous FX rotation*
No rotation
Rotating CW Fast CW Slow
No rotation (stops at current position)
Rotating CCW Slow CCW Fast
No rotation
Static FX*
Min - Max
Fade 128
25
0 - 255
0 - 2
3 - 126
127 - 129
130 - 253
254 - 255
0 - 50
51 - 100
100 - 255
Ray 2 Indexing
Indexing 0° - 360°
Ray 2 Rotation
No rotation
Rotating CW Fast CW Slow
No rotation
Rotating CCW Slow CCW Fast
No rotation
Continuous FX start times*
Synchronized (all fixtures start FX
immediately)
Random (0 - 6 seconds random offset
between fixtures)
No function
Fade 128
Table 1: Quadray Module DMX channels

Martin MAC III™ Quadray Module Installation and DMX Control Guide 7
*These functions become available if you select one of the pre-programmed FX on channel 23.
Quadray FX
With the Quadray Module installed, the MAC III AirFX DMX protocol includes a range of
pre-programmed effects. You can select these FX by sending values of 101 and above on DMX channel
23 according to the following table. You can then adjust parameters of the effects on channels 24 and
25.
26
0 - 255
0 - 2
3 - 126
127 - 129
130 - 253
254 - 255
Ray 3 Indexing
Indexing 0° - 360°
Ray 3 Rotation
No rotation
Rotating CW Fast CW Slow
No rotation
Rotating CCW Slow CCW Fast
No rotation
Fade 128
27
0 - 255
0 - 2
3 - 126
127 - 129
130 - 253
254 - 255
Ray 4 Indexing
Indexing 0° - 360°
Ray 4 Rotation
No rotation
Rotating CW Fast CW Slow
No rotation
Rotating CCW Slow CCW Fast
No rotation
Fade 128
DMX value
on ch. 23 FX Description
101
102
103
104
105
106
107 - 109
110
111
112
113
114
115
116
117 - 119
120
121
122
123 - 128
129
130
Positions
Home
Out
Horizontal V
Ver ti ca l V
Diagonal 1
Diagonal 2
No function
3 ray fan
3 ray top
3 ray bottom
3 ray left
3 ray right
Narrow 3 ray left
Narrow 3 ray right
No function
4 ray fan H
4 ray fan V
4 ray fan 2
No function
Random
Random 2
Channel 24 adjusts fade time
Every ray takes a random position
Every ray takes a random position
Table 2: Quadray FX
Table 1: Quadray Module DMX channels

Martin MAC III™ Quadray Module Installation and DMX Control Guide 8
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154 - 159
160
161 - 178
179
180
181
182
183
184 - 255
Continuous FX
Rotate
Bounce
Pair H
Pair V
Cross
Cross Bounce
Pair Bounce
Cross Bounce 2
Singles
Singles reset
Singles bounce
Juggler
Fold out
Fold In
Fold in-out
V-Chase
Fan Chase
Pair Chase
Ripple
Home - Out
Home and fan chase
Wide single rotation
Wide mirror rotation
No function
‘Shake It’
No function
Random direction
Random ray
Static FX
Expand
Expand mirror
Spread
No function
Channel 24 adjusts speed and direction
Channel 25 sets sync or random start points
All rays rotate
All rays 0° to 360°, small pause, then 360° to 0°, small pause
1+4 rotate one way, 2+3 the opposite way
1+2 rotate one way, 3+4 the opposite way
1+3 rotate one way, 2+4 the opposite way
1+3 fade 0°-360°, 2+4 fade 360° - 0°, pause, then reverse,
pause
2+3 fade 0°-360°, 1+4 fade 360° - 0°, pause, then reverse,
pause
1+3 fade 30°-330°, 2+4 fade 330° - 30°, pause, then reverse,
pause
Ray 1 rotates 0°-360°, then ray 2, then 3, then 4, 1, 2, 3, 4 etc.
Same as singles, but one ray fades backwards as the next ray
fades forwards
1,2,3,4 forward, pause, 4,3,2,1 backwards, pause
All rays start from 180°. then 1 to 0°, then 1 to 180°, 2 to 0°,
then 2 to 180°, 3 to 0°, then 3 to 180°, 4 to 0°, then 4 to 180°, 1
to 0°
1 to 180°, then 2 to 180°, then 3, then 4, pause, all to Home
All to 180°, Pause, then 1 to 0°, 2 to 0°, 3 to 0°, 4 to 0°, pause
1 to 180°, then 2 to 180°, then 3, then 4, pause, 1 to 0°, 2 to
0°, 3 to 0°, 4 to 0°, pause
Alternate horizontal and vertical V shape with small pause
Alternate horizontal and vertical fan with small pause
1+2 from 0° - 360°, then 3+4 from 0° to 360°, then 1+2 to 0°,
then 3+4 to 0°
1 at 0°, 2 at 45°, 3 at 90° and 4 at 135°, then rotate
Alternate Home and Out position: 1+3 go CW, 2+4 opposite
Home, 4 ray fan H, Home, 4 ray fan V
All rays start at 180°, 1 rotates 180° to 180°, then 2, then 3,
then 4
All rays start at 180°, 1+3 rotate 180° to 180°, then 2+4
All rays move to 180° and shake
All rays rotate from Home position, but in random directions
All rays assume random positions and directions
Channel 24 adjusts amount
Home at 0°, then 1-4 move from 0° to 360°
Home, then 1+3 move CW from 0° to 360° while 2+4 move
CCW from 360° to 0°
Home, then 1 moves to 180°, then 2 moves to 180°, then 3 to
180°, then 4 to 180°
Table 2: Quadray FX
Martin Professional A/S •Olof Palmes Allé 18 •8200 Aarhus N •Denmark
Tel: [phone] •Fax [phone] •www.martin.com