Marvin Ultimate Glider User manual

4/27/20
19916116
Ultimate Glider WOCD
Field Applied Instructions
Failure to follow these instructions may result in the win-
dow opening control devices (WOCDs) being ineffective
in controlling the window opening.
A copy of the safety information shall be provided to the
owner of the building in which the window opening con-
trol device (WOCD) is installed and to the occupant in
the dwelling where the opening control device is in-
stalled (or is to be installed).
NOTE: This instruction is for Ultimate Glider (UGL).
When installed and used as directed, the Window
Opening Control Device meets the requirements of
ASTM F2090-17.
Building and fire codes shall be consulted before install-
ing WOCDs. Contact local building code department or
fire department for specific applicable codes and install
in accordance.
Follow manufacturer’s assembly and installation in-
structions carefully. Failure to do so may result in acci-
dental window falls.
WARNING!
Possible Fall Hazard
• Young children may fall out of the window if the
window opening control device (WOCD) is not
installed correctly.
• Install the device so that a rigid 4.0-in. (102mm)
diameter sphere does not pass through any space
at the lowest opening portion in the window
opening after the WOCD is in place.
• Young children may fall out of the window if all
installation instructions are not followed.
• Use recommended materials and techniques.
• Make sure that the WOCD is securely installed in
accordance with manufacturer’s instructions.
• Make sure that the window frame is in good
condition.
NOTE: Once installation of unit is complete, check
WOCD for proper operation. When the sash is closed
and locked, the WOCD should automatically engage.
NOTE: Available on all 2-panel and 3-panel sizes. Not
available for OXXO units.
Required Tools:
• Phillips screwdriver (No. 2)
• Clamp
• WOCD Stile Jig (UGL)
• WOCD Check Rail Jig (UGL)
• 1/4" ID, 5/16" OD Router Guide
• Router Lock Nut
•Router
• 1/4" Dia. Router Bit for Wood
• 1/4" Dia. Router Bit for Fiberglass
• Two #7 x 7/8" screws
• Drill with 7/64" Drill Bit
• Vacuum
Parts needed or to be replaced:
• If the top or bottom sash is damaged, contact
Customer Support, it may need to be replaced with
a sash with factory-applied WOCD components.
For kit details, refer to Table 1.

4/27/20 2 Ultimate Glider WOCD
19916116 Field Applied Instructions
Table 1: Field-applied WOCD kit details
Field-Applied Install Process
IMPORTANT
Inspect all fabrication jigs before and after each use. Ensure steel inserts are not loose and do not show heavy wear.
Contact Customer Support if a replacement is needed.
Primary Sash
NOTE: Lay sash on a flat surface and secure with a
clamp before performing the following steps.
1. Remove screws from interlock. See Figure 1.
Figure 1
2. Using a square and pencil, mark the 1 1/2" x 3/4"
notch and remove material. See Figure 2.
Figure 2
3. Install the window opening control bumper at the
bottom of the sash and fasten with 1" screw. See
Figure 3.
Part No. Description Qty Notes
19916116 Field Installation Instructions 1
19916102 Hang Tag 1
19915447 Safety and Operating Information 1 One for owner, copy for occupant
11718011 WOCD Sticker 1
See notes WOCD Assembly 1 part number depends on finish color
See notes WOCD Assembly Screws 2 part number depends on finish color
See notes WOCD Bumper 1 part number depends on finish color
11805150 WOCD Bumper Screw 1

4/27/20 3 Ultimate Glider WOCD
19916116 Field Applied Instructions
Figure 3
4. Reinstall the interlock using a wood block or rubber
mallet (supplied by others) and reinstall the screws. See
Figure 4.
Figure 4
Secondary Sash
1. Lay sash on a flat surface. Remove the bottom rail
glide blocks from the bottom rail. See Figure 5.
Figure 5
2. Place the jig on the bottom rail and position against
the check rail. Secure with two #7 x 1" screws (not
provided) into the bottom rail. See Figure 6.
Figure 6
3. Set router depth to 13/16" and route. See Figure 7.

4/27/20 4 Ultimate Glider WOCD
19916116 Field Applied Instructions
Figure 7
4. Remove the jig and clean debris and excess
material. Install the window opening control device with
the screws provided. See Figure 8.
Figure 8
5. Apply the window opening control device sticker on
the sill between the sill liner and sill track. See Figure 9.
Figure 9