Masport Aerocore CGT60H.9 User manual
546872 - Masport Aerocore Line Trimmer Owner’s Manual - December 2020
1
Pantone 648C
masport.com Part No: 546872.A.0
December 2020
Aerocore Line Trimmer
Important
Please read these instructions carefully before assembly, to reduce risk of
re, burn hazard or other injury.
Keep these instructions in a safe place for future use.
This manual covers the Masport Aerocore Line Trimmer
Owner’s Manual
Masport Aerocore Line Trimmer
546872 - Masport Aerocore Line Trimmer Owner’s Manual - December 2020
2
2
Carefully read owner's
manual before handling
the machine.
Observe instructions and
safety rules when operat-
ing.
Shut off engine and
remove power cord before
untangling the power cord
and when performing
cleaning, maintenance or
repair work.
Wear eye
protection.
Protect
against
moisture.
Keep your
hands out of
the immedi-
ate vicinity
of rotating
parts.
Keep your
hands and
feet away
from sharp
parts.
Danger – objects may be
thrown out at high speed
when motor is running.
Keep people, pets and
domestic animals out of
the danger
Do not operate this machine before it has been
assembled correctly and you have read and
understood these instructions.
Keep the instructions in a safe place for future use.
Keep the
lead away
from sharp
parts.
Keep the
supply
flexible cord
away from
the cutting
blades.
Symbols on the Machine
Contents
2enihcamehtnoslobmyS
3launaMs’renwOsihtnislobmyS
3gninrawytefaS
3gnikrowefaS
4egasureporP
4ecnanetniaM
4pu-tratSerofeB
5tnemegnarrAlareneG
5ylbmessA
7noitarepO
7rewomehtgnisU
8ecnanetniamdnaeraC
8Troubleshooting
Do not expose to rain.
Recycling symbol.
RCM symbol
Li-Ion battery. This product has
been marked with a symbol relating
to ‘separate collection’ for all bat-
tery packs and battery pack. It will
then be recycled or dismantled in
order to reduce the impact on the
environment. Battery packs can be
hazardous for the environment and
for human health since they contain
hazardous substances.
Do not burn
Batteries may enter water cycle if
disposed improperly, which can
be hazardous for ecosystem. Do
not dispose of waste batteries as
unsorted municipal waste.
For indoor use only
Read the operator’s
manual.
Fuse
Positve Terminal
Negative Terminal
Double Insulation
2
Carefully read owner's
manual before handling
the machine.
Observe instructions and
safety rules when operat-
ing.
Shut off engine and
remove power cord before
untangling the power cord
and when performing
cleaning, maintenance or
repair work.
Wear eye
protection.
Protect
against
moisture.
Keep your
hands out of
the immedi-
ate vicinity
of rotating
parts.
Keep your
hands and
feet away
from sharp
parts.
Danger – objects may be
thrown out at high speed
when motor is running.
Keep people, pets and
domestic animals out of
the danger
Do not operate this machine before it has been
assembled correctly and you have read and
understood these instructions.
Keep the instructions in a safe place for future use.
Keep the
lead away
from sharp
parts.
Keep the
supply
flexible cord
away from
the cutting
blades.
Symbols on the Machine
Contents
2enihcamehtnoslobmyS
3launaMs’renwOsihtnislobmyS
3gninrawytefaS
3gnikrowefaS
4egasureporP
4ecnanetniaM
4pu-tratSerofeB
5tnemegnarrAlareneG
5ylbmessA
7noitarepO
7rewomehtgnisU
8ecnanetniamdnaeraC
8Troubleshooting
Carefully read owner’s
manual before handling
the machine. Observe
instructions and safety
rules when operating.
Wear eye protection.
2
Carefully read owner's
manual before handling
the machine.
Observe instructions and
safety rules when operat-
ing.
Shut off engine and
remove power cord before
untangling the power cord
and when performing
cleaning, maintenance or
repair work.
Wear eye
protection.
Protect
against
moisture.
Keep your
hands out of
the immedi-
ate vicinity
of rotating
parts.
Keep your
hands and
feet away
from sharp
parts.
Danger – objects may be
thrown out at high speed
when motor is running.
Keep people, pets and
domestic animals out of
the danger
Do not operate this machine before it has been
assembled correctly and you have read and
understood these instructions.
Keep the instructions in a safe place for future use.
Keep the
lead away
from sharp
parts.
Keep the
supply
flexible cord
away from
the cutting
blades.
Symbols on the Machine
Contents
2enihcamehtnoslobmyS
3launaMs’renwOsihtnislobmyS
3gninrawytefaS
3gnikrowefaS
4egasureporP
4ecnanetniaM
4pu-tratSerofeB
5tnemegnarrAlareneG
5ylbmessA
7noitarepO
7rewomehtgnisU
8ecnanetniamdnaeraC
8Troubleshooting
Danger – objects may be
thrown out at high speed
when motor is running.
Keep people, pets and
domestic animals out of the
danger.
Symbols 2
General Power Tool Safety Warnings 3
Safety warning for Battery Pack 4
Safety Warning for Battery Charger 4
Additional Safety warnings for Line Trimmer 4
Product Specications 6
Product Diagram 6
Assembly 6
Operation 7
Maintenance 8
Storage 9
Troubleshooting 9
546872 - Masport Aerocore Line Trimmer Owner’s Manual - December 2020
3
General Power Tool Safety Warnings
WARNING Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in
electric shock, re and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-
operated (corded) power tool or battery-operated (cordless)
power tool.
1) Work area safety
a) Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of ammable
liquids, gases or dust. Power tools create sparks which
may ignite the dust or fumes.
c) Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs with
earthed (grounded) power tools. Unmodied plugs and
matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock if
your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of electric
shock.
d) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the risk of electric
shock.
e) When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
f) If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of electric
shock.
3) Personal safety
a) Stay alert, watch what you are doing and use
common sense when operating a power tool. Do not use
a power tool while you are tired or under the inuence
of drugs, alcohol or medication. A moment of inattention
while operating power tools may result in serious personal
injury.
b) Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask, non-
skid safety shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in
the o-position before connecting to power source and/
or battery pack, picking up or carrying the tool. Carrying
power tools with your nger on the switch or energising
power tools that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power tool in
unexpected situations.
f) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away from
moving parts. Loose clothes, jewellery or long hair can be
caught in moving parts.
g) If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of these devices can
reduce dust-related hazards.
h) Do not let familiarity gained from frequent use of tools
allow you to become complacent and ignore tool safety
principles. A careless action can cause severe injury within a
fraction of a second.
4) Power tool use and care
a) Do not force the power tool. Use the correct power
tool for your application. The correct power tool will do the
job better and safer at the rate for which it was designed.
b) Do not use the power tool if the switch does not turn
it on and o. Any power tool that cannot be controlled with
the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/or
the battery pack from the power tool before making any
adjustments, changing accessories, or storing power
tools. Such preventive safety measures reduce the risk of
starting the power tool accidentally.
d) Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power tools
are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any other
condition that may aect the power tool’s operation. If
damaged, have the power tool repaired before use. Many
accidents are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained
cutting tools with sharp cutting edges are less likely to bind
and are easier to control.
g) Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into account
the working conditions and the work to be performed.
Use of the power tool for operations dierent from those
intended could result in a hazardous situation.
h) Keep handles and grasping surfaces dry, clean and
free from oil and grease. Slippery handles and grasping
surfaces do not allow for safe handling and control of the tool
in unexpected situations.
5) Battery tool use and care
a) Recharge only with the charger specied by the
manufacturer. A charger that is suitable for one type of
battery pack may create a risk of re when used with another
battery pack.
b) Use power tools only with specically designated
battery packs. Use of any other battery packs may create a
risk of injury and re.
c) When battery pack is not in use, keep it away from
other metal objects, like paper clips, coins, keys, nails,
screws or other small metal objects, that can make a
connection from one terminal to another. Shorting the
battery terminals together may cause burns or a re.
d) Under abusive conditions, liquid may be ejected from
the battery; avoid contact. If contact accidentally occurs,
546872 - Masport Aerocore Line Trimmer Owner’s Manual - December 2020
4
ush with water. If liquid contacts eyes, additionally seek
medical help. Liquid ejected from the battery may cause
irritation or burns.
e) Do not use a battery pack or tool that is damaged
or modied. Damaged or modied batteries may exhibit
unpredictable behaviour resulting in re, explosion or risk of
injury.
f) Do not expose a battery pack or tool to re or
excessive temperature. Exposure to re or temperature
above 130 °C may cause explosion.
g) Follow all charging instructions and do not charge
the battery pack or tool outside the temperature range
specied in the instructions. Charging improperly or at
temperatures outside the specied range may damage the
battery and increase the risk of re.
6) Service
a) Have your power tool serviced by a qualied repair
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
b) Never service damaged battery packs. Service of
battery packs should only be performed by the manufacturer
or authorized service providers.
Safety warning for Battery Pack
a) Do not dismantle, open or shred cells or battery pack.
b) Do not short-circuit a battery pack. Do not store
battery packs haphazardly in a box or drawer where they
may short-circuit each other or be short-circuited by
conductive materials. When battery pack is not in use, keep
it away from other metal objects, like paper clips, coins, keys,
nails, screws or other small metal objects, that can make a
connection from one terminal to another. Shorting the battery
terminals together may cause burns or a re.
c) Do not expose battery pack to heat or re. Avoid
storage in direct sunlight.
d) Do not subject battery pack to mechanical shock.
e) In the event of battery leaking, do not allow the liquid
to come into contact with the skin or eyes. If contact
has been made, wash the aected area with copious
amounts of water and seek medical advice.
f) Seek medical advice immediately if a cell or battery
pack has been swallowed.
g) Keep battery pack clean and dry.
h) Wipe the battery pack terminals with a clean dry cloth
if they become dirty.
i) Battery pack needs to be charged before use. Always
refer to this instruction and use the correct charging
procedure.
j) Do not maintain battery pack on charge when not in
use.
k) After extended periods of storage, it may be
necessary to charge and discharge the battery pack
several times to obtain maximum performance.
l) Battery pack gives its best performance when it is
operated at normal room temperature (20 °C ± 5 °C).
m) When disposing of battery packs, keep battery packs
of dierent electrochemical systems separate from each
other.
n) Recharge only with the charger specied by Masport.
Do not use any charger other than that specically
provided for use with the equipment. A charger that is
suitable for one type of battery pack may create a risk of re
when used with another battery pack.
o) Do not use any battery pack which is not designed for
use with the equipment.
p) Keep battery pack out of the reach of children.
q) Retain the original product literature for future
reference.
r) Remove the battery from the equipment when not in
use.
s) Dispose of properly.
t) Do not mix cells of dierent manufacture, capacity,
size or type within a device.
u) Do not remove battery pack from its original
packaging until required for use.
v) Observe the plus (+) and minus (–) marks on the
battery and ensure correct use.
Safety warning for Battery Charger
1. Before charging, read the instructions.
2. For charge Li-ion battery pack only.
3. Do not charge a leaking battery.
4. Do not use chargers for works other than those for which
they are designed.
5. Before charging, ensure your charger is matching the local
AC supply.
6. The charging device must be protected from moisture.
7. Do not use the charging device outdoors.
8. Do not short out the contacts of battery or charger.
9. Respect the polarity “+/-“ when charging.
10. Do not open the unit and keep it out of the reach of
children.
11. Do not charge the batteries of other manufactures or ill-
suited models.
12. Ensure that the connection between the battery charger
and battery is correctly positioned and is not obstructed by
foreign bodies.
13. Keep battery charger’s slots free of foreign objects and
protect against dirt and humidity. Store in a dry and frost-free
place.
14. When charging batteries, ensure that the battery charger
is in a well-ventilated area and away from inammable
materials. Batteries can get hot during charging. Do not
overcharge any batteries. Ensure that batteries and chargers
are not left unsupervised during charging.
15. Do not recharge non-rechargeable batteries, as they can
overheat and break.
16. Longer life and better performance can be obtained
if the battery pack is charged when the air temperature is
between 18℃ and 24℃. Do not charge the battery pack in
air temperatures below 0℃, or above 40℃. This is important
as it can prevent serious damage to the battery pack.
17. Charge only battery pack of the same model provided by
Masport and of models recommended by Masport.
Addtional safety warnings for line
trimmer
WARNING! Read all safety warnings and all
instructions. Failure to follow the warnings and instructions
may result in electric shock, re and/or serious injury.
546872 - Masport Aerocore Line Trimmer Owner’s Manual - December 2020
5
Carefully read the instructions for the safe operation of
the machine.
Save all warnings and instructions for future reference.
This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not
play with the appliance.
IMPORTANT
READ CAREFULLY BEFORE USE
KEEP FOR FUTURE REFERENCE
Safe operating practices
1 Training
a) Read the instructions carefully. Be familiar with the controls
and the proper use of the
machine.
b) Never allow people unfamiliar with these instructions or
children to use the machine. Local regulations can restrict the
age of the operator.
c) Keep in mind that the operator or user is responsible
for accidents or hazards occurring to other people or their
property.
2 Preparation
a) Never operate the machine while people, especially
children, or pets are nearby.
b) Wear eye protection and stout shoes and appropriate PPE
at all times while operating the machine.
3 Operation
a) Use the machine only in daylight or good articial light.
b) Never operate the machine with damaged guards or
shields or without guards or shields in place.
c) Switch on the motor only when the hands and feet are
away from the cutting means.
d) Always remove the battery pack from the appliance,
– whenever leaving the machine unattended;
– before clearing a blockage;
– before checking, cleaning or working on the machine;
– after striking a foreign object;
– whenever the machine starts vibrating abnormally.
e) Take care against injury to feet and hands from the cutting
means.
f) Always ensure that the ventilation openings are kept clear
of debris.
4 Maintenance and storage
a) Remove the battery pack from the appliance before
carrying out maintenance or cleaning work.
b) Use only the manufacturer’s recommended replacement
parts and accessories.
c) Inspect and maintain the machine regularly. Have the
machine repaired only by an authorized repairer.
d) When not in use, store the machine out of the reach of
children.
546872 - Masport Aerocore Line Trimmer Owner’s Manual - December 2020
6
Product Specications
Product Diagram
1. Battery Pack*
2. Battery pack release button
3. On/O switch
4. Lock-o button
5. two-speed gear control
6. Auxiliary handle
7. Couplings
8. Safety guard
9. Line Cutter
10. Trimmer head
11. Spool
12. Bump knob
13. Hex key (g. A2)
14. Bolts x 5 (g. B)
We recommend that you purchase your accessories from
the same store that sold you the tool. Refer to the accessory
packaging for further details. Store personnel can assist you
and oer advice.
Assembly
To reduce the risk of injury, user must read
instruction manual.
Intended Use
The machine is intended for the cutting of grass and
weeds under bushes, as well as on slopes and edges that
cannot be reached with the lawn mower.
1. Assembling the upper shaft and lower shaft
-Connect the couplings into each other. (See Fig. A1)
-Align the holes and fasten the couplings by tightening the
bolt with hex key. (See Fig. A2 )
2. Assembling the auxiliary handle
- Place the auxiliary handle onto the shaft from the top, and
align with the anti-vibration circle on the shaft. Secure the
auxiliary handle by tightening the four bolts with the hex key.
(See Fig. B)
CAUTION!
•The machine must not be operated before it has
been assembled completely.
•Do not insert the battery until the appliance has been
completely assembled.
3. Assembling the safety guard
Attach the safety guard to the trimmer head. Align the guard
so it slides into the slots located on the trimmer head. (See
Fig. C1)
Secure the safety guard onto the trimmer head with the bolts
provided by using hex key. (See Fig. C2)
Product Aerocore Line Trimmer
CGT60H.9
Rated Voltage 60V MAX
No Load Speed 4200/5500/min
Cutting Diameter 400mm
Line Diameter 2.4mm
Battery Capacity
[553155 / ABP6025H]* 2.5 Ah
Battery Capacity
[553156 / ABP6050H]* 5.0 Ah
Charger Input
[553157 / ACG6025H]* 100-240V ~ 50/60Hz
Charger Output
[553157 / ACG6025H]* 60V 2.5 A
Charging Time (approx.) 1 hr
Charger Protection Class / II
Machine Weight 5.90kg (Machine only)
*Not included in some models
546872 - Masport Aerocore Line Trimmer Owner’s Manual - December 2020
7
Operation
BEFORE PUTTING INTO OPERATION
1. CHARGING THE BATTERY (SEE FIG. B)
a. The battery in your new tool is not charged when it leaves
the plant; therefore, it must be full charged before using the
rst time.
b. If the battery pack is very hot, remove the battery from the
charger and allow it to cool to ambient temperature before
attempting to recharge.
c. To prevent damage to the battery pack, please charge the
battery to full or no less than half charge before storage.
d. If the tool will not be used for long periods of time, charge
the battery pack every 3-6 months.
CHARGING PROCEDURE
1) Plug the charger into an appropriate outlet.
2) Slide the battery pack into the charger, and make sure the
battery is in the correct charge position rmly. The light will
begin ashing green to indicate the charging process has
started.
3) When charging is completed, the light will turn solid green.
4) After the battery is fully
charged, unplug the charger
and remove the battery
pack.
NOTE: If
the battery pack is locked
in the charger, press the
battery pack release button
and remove it.
Warning! The charger and battery pack are
specially designed to work together so do not attempt
to use any other devices. Never insert or allow metallic
objects into your charger or battery pack connections
because an electrical failure and hazard will occur.
WARNING: When battery charge runs out after
continuous use or exposure to direct sunlight or heat,
allow time for the tool to cool down before re-charging
to achieve the full charge.
CHARGING INDICATOR
This charger is designed to detect some problems that can
arise with battery packs. Indicator lights indicate problems
(see table below).
Light ON/Flash Status
Red on Defective Battery
Red ash
Battery Temperature Protection.
The temperature of the battery
pack is less than 0oC or more
than 40oC.
Green on Fully Charged
Green ash Charging
2. Installing and removing the battery pack
Slide the battery pack into tool’s battery port. A simple push
and slight pressure will be sucient. (See Fig. E1)
Press the battery pack latch and remove the battery pack
from the tool. (See Fig. E2)
3. OPERATION
3.1 Switch On/O
To switch on, press the lock-o button rst, then the On/O
switch. (See Fig. F)
To switch o, release the On/O switch.
3.2 Two-speed gear control
The tool has a two-speed gear control designed for working
at Low (mark is 1) or High (mark is 2) speeds. (See Fig. G)
Select either Low or High speed according the required
working condition.
4. Trimming
a) Keep the trimmer head at an angle of about 30° to the
ground when trimming. (See Fig. H1)
b) Do not cut wet grass because it tends to stick to the
trimmer head and guard, prevents proper discharge of grass
clippings, and could cause you to slip and fall.
c) Regularly remove clippings and dirt around the trimmer
head with a switched o trimmer.
d) Work rhythmically; stand rmly with your feet apart. Cut
from right to left so the trimmings will be thrown away from
the work area. (See Fig. H2)
e) When cutting longer /high grass, please make sure that
you cut the grass down in 2 to 3 stages. (See Fig. H3,H4)
f) Do not move the trimmer too fast as this will result in
ineective cutting and possible damage.
Warning:
•Always wear eye protection. Never lean over
the trimmer head. Rocks or debris can ricochet or
be thrown into eyes and face and cause blindness or
other serious injury.
• Make sure that line is fed out before operation. Make
sure motor is up to full speed before trimming.
546872 - Masport Aerocore Line Trimmer Owner’s Manual - December 2020
8
5. Adjusting cutting line length
The trimmer head allows the operator to release more
cutting line without stopping the motor. As line becomes
frayed or worn, additional line can be released by lightly
tapping the bump knob on the ground while operating the
trimmer. (See Fig. I)
NOTICE: Line release will become more dicult if the
cutting line becomes too dull.
WARNING: Do not remove or alter the line-cutting
blade assembly. Excessive line length will be cut to
suitable length
6. To replace the spool and line
For your convenience, it is recommended you buy a
replacement spool with line.
Press and hold in the two cap release latches. Rotate and
loosen the cap by rotating it counter-clockwise. Pull cap
away from the spool holder. (See Fig. J1)
Remove old spool. (See Fig. J2)
Place new spool into cutting head. Release one line from
cleat and feed line through eyelet. (See Fig. J3)
Replace the cap on the spool holder and turn the cap
clockwise to tighten. (See Fig. J4)
Note: If required, line can be fed out manually. Gently pull
out the 2 lines out until the lines reach the line cutter. If the
line extends past the line cutter, too much line has been
fed out. If too much line is fed out, remove the spool cap
and click spool counter-clockwise until the line is at the
desired length.
Note: Remove battery prior to replacing spool and line.
7. To replace the line only
Use approximately 16’ (4.9 m) of line.
Insert the centre point of line into the notch in the middle
section of the spool and wind the line in a clockwise direction
on both the upper and lower sections of spool. (See. Fig. K1)
Care should be taken to ensure that the line is neatly coiled
on the spool. Failure to do so will impair the eciency of the
automatic bump line feed. (See. Fig. K2)
Then t spool as described in “To Replace the Spool and
Line ”.
Warning!
•Your trimmer is designed to use only line with a
maximum diameter of 0.09” (2.4 mm).
•Always remove the battery pack from your trimmer
after use.
Maintenance
Always check the product prior to being used for any
damage. After use, disconnect the battery from the tool
and check for damage. Your power tool requires no
additional lubrication or maintenance. There are no user-
serviceable parts in your power tool. Never use water or
chemical cleaners to clean your power tool. Wipe clean
with a dry cloth. Always store your power tool in a dry, room
temperature location. Keep the motor ventilation slots clean.
Keep all working controls free of dust.
546872 - Masport Aerocore Line Trimmer Owner’s Manual - December 2020
9
Cleaning the tool
Clean the tool regularly.
For battery tools
The ambient temperature range for the use and storage of
tool and battery is 0 — 45oC (32 — 113oF).
The recommended ambient temperature range for the
charging system during charging is 0 — 40oC (32 — 104oF).
It is recommended that the battery be stored indoors for the
winter months.
Storage
Remove the battery pack and disassemble the line trimmer.
Store the line trimmer and the battery pack indoors, in a
cool, dry, clean place which is protected from the eects of
weather and temperature and is out of the reach of children
and animals.
Warning! Keep your product dry. Under no
circumstances spray with water
Troubleshooting
Symptom Possible Causes Solution
Trimmer fails to
operate.
Battery discharged.
Battery too hot/cold.
Motor is broken.
Internal wiring of
machine damaged.
Recharge battery;
also see the content in
charger manual.
Allow to cool/warm.
Contact Masport
service dealer.
Contact Masport
service dealer.
Trimmer runs
intermittently.
Motor is broken.
Battery not fully
charged.
On/O switch
defective.
Contact Masport
service dealer.
Recharge battery.
Contact Masport
service dealer.
Excessive vibrations/
noise.
Machine defective.
Line spool is not
wound well.
Contact Masport
service dealer.
Rewind the line. See
“To Replace the Line
on the Spool’’.
Cutting time per
battery charge too
short.
Battery has not been
used for long period or
only charged for short
term.
Grass too high.
Fully charge battery;
also see
the content in charger
manual.
Cut in stages.
Machine does not cut.
Line broken.
Battery not fully
charged.
Motor is broken (speed
is too low).
Replace the line.
Recharge battery; also
see.
the content in charger
manual.
Contact Masport
service dealer.
Continuous lighting
of the battery charge
indicator/battery not
charging.
Battery not (properly)
inserted.
Battery contacts
contaminated.
Properly insert battery
into battery charger.
Clean the battery
contacts or replace the
battery.
Replace the battery.
Battery charge
indicator does not
light up.
Plug of battery
charger not plugged in
(properly).
Outlet or mains cable
defective.
Battery charger
defective.
Insert mains plug (fully)
into the socket outlet.
Check the mains
voltage.
Replace the battery
charger.
546872 - Masport Aerocore Line Trimmer Owner’s Manual - December 2020
10
546872 - Masport Aerocore Line Trimmer Owner’s Manual - December 2020
11
546872 - Masport Aerocore Line Trimmer Owner’s Manual - December 2020
12
Masport Ltd
320 Ti Rakau Drive, East Tamaki, Auckland 2013
New Zealand
P.O.Box 14 349, Panmure, Auckland 1741
This manual suits for next models
2
Table of contents
Other Masport Trimmer manuals
