Matrix COSEC COGNIFACE INTEGRA200 User manual

COSEC COGNIFACE INTEGRA200 Safety Instructions
These instructions are intended to ensure that the user can
use the product correctly to avoid danger or property loss.
Do not install the device:
ŸOn unstable surface.
ŸWhere ferromagnetic field or noise is induced.
ŸWhere static is created, such as desks made of plastics,
carpets.
ŸNear volatile inflammable materials or inflammable goods
such as drapes.
ŸWhere volatile gas and/or inflammable gas is created.
Cautions
ŸInstalling and servicing should be done only by qualified
technician.
ŸThere are no user-serviceable parts inside.
ŸOpening or removing the device cover may result in
electric shock or exposure to other hazards.
ŸUse the device only for the purpose for which it was
designed.
WARNING
Quick Installation Guide
11.19"

CONTENTS
Please read this guide first for correct installation and retain it for future reference. The information
in this guide is prevailing at the time of publication. However, Matrix Comsec reserves the right to
make changes in product design and specifications without prior notice.
Copyright
All rights reserved. No part of this document may be copied or reproduced in any form or by any
means without the prior written consent of Matrix Comsec.
Warranty
Limited Warranty. Valid only if primary protection is provided, mains supply is within limit and
protected, and environment conditions maintained within product specifications. Complete
warranty statement is available on our website:
www.matrixaccesscontrol.com
Know your COGNIFACE INTEGRA200
A COSEC COGNIFACE INTEGRA200 is an enclosure box which helps in maintaining
hardware elements to encourage Face Recognition feature for Time and Attendance
module through Matrix Devices. Here a COSEC device is integrated with IP Camera to
perform Face Recognition efficiently.
4
4
Know your COGNIFACE INTEGRA200
What Your Package Contains
Things You Will Need
8
Pre-Installation Safety Instrctions
Disposal of Product after End-Of-Life
Installation Instructions
Technical Specifications
Assigning IP Address
and Other Network Settings
Preparing for Installation
7
7
13
27
28
29
8
The Figure Represents:
1. Matrix IP Camera - MIDR20FL28CWS
2. COSEC Device - ARGO (FOE 212/ FOM 212)
3. ON/OFF Switch
4. Power Cable Slot
1
3
4
5
6
7
2
Variants
5. LAN Slot
6. Earthing Label
7. Earthing Screw
Front View:
Figure 1
7

COSEC Device - ARGO
The Matrix ARGO device, is engineered with high-end Wireless terminals for Time &
Attendance. This door have Graphic display screen with touch pad, a Finger Sensor
and Card Sensing area (Refer figure 4). Thus making it best solution for providing
Face recognition feature when it is integrated with IP Camera. The user image
captured by IP camera is processed by ARGO door to authorize the user for Time
and Attendance Management. Also, other credentials like Finger, PIN and Card are
supported by ARGO.
Finger Sensor
Card Sensing Area
Touch Screen Display
For providing efficient Face Recognition, IP Camera is used to capture user’s image
accurately. In COGNIFACE INTEGRA200, Matrix IP Camera - MIDR20FL28CWS is
used (Refer Figure 3). It is a Standard 2MP Dome Camera with Focal length of
2.8mm. Mounted above COSEC ARGO device at suitable height in COGNIFACE
INTEGRA200, it captures user image from the best angle. The captured image is
used to identify users for Time and Attendance management.
Note: The lens angle of camera is set at 15° downwards for obtaining best results.
Back View:
1
3
2
The Figure represents:
1. Key slot (for Key slot Mounting)
2. Though slot (for Through slot Mounting)
3. Battery Compartment.
Matrix IP Camera - MIDR20FL28CWS
56
Figure 2
Figure 3
Figure 4

Variants
The COSEC COGNIFACE INTEGRA200 have 2 variants depending on type
of ARGO device embedded. They are:
Ÿ COSEC COGNIFACE INTEGRA200E (ARGO FOE212)
Ÿ COSEC COGNIFACE INTEGRA200M (ARGO FOM212)
Things You will Need
ŸPower Drill
ŸA Screw Driver
ŸCOSEC Software with FR license.
ŸPower Adaptor 12VDC, 2A
ŸCOSEC Cogniface Integra200 device unit
ŸScrew Grips Plastic 8X35 - 4 Nos
ŸScrew M5X25 CSK PH - 4 Nos
ŸMounting Template
ŸEarthing Cable
What your Package contains
Pre-Installation Safety Instructions
1. Do not Install the device in extremely hot temperature or under direct
Sunlight or at bright places. This may affect LCD and Finger print Sensor of
device.
2. Recommended height from ground to the top of the device is
151 cm for best results.
3. Recommended distance between the IP Camera and the Face is 60 cm
for more effective face recognization.
4. Do not install on unstable surfaces, near volatile inflammable materials,
Area where volatile Gas is created, where ferro-magnetic field or noise is
induced, where static s created, such as desk made up of plastic or carpet.
5. Do not expose the device to extreme weather condition.
Preparing for Installation
Before Wall mounting COSEC COGNIFACE INTEGRA200, follow the
below given instructions:
Connecting Earthing Cable:
Remove the Earthing Screw with the help of screw driver and connect
the provided Earthing cable in the slot.
Battery Insertion
Note: This is optional if battery backup is not needed.
Recommended Battery Specification: 3.75V, 3000mAh to 5000mAh, Li-
ion (Panasonic/ LG).
Note: To power COGNIFACE INTEGRA200, plug-in the Adaptor and connect the
cable into power cable slot and Switch ON the device. This will provide power to all
the devices: IP Camera, COSEC ARGO and FR Module in COGNIFACE INTEGRA200.
78

After opening the battery compartment, place four battery cells in the space
given as shown in figure 6.
Remove the lid of battery compartment by unscrewing four screws with the help
of screw driver. Keep those screws aside carefully because they will be required to
fix the lid of battery compartment back into its position once the battery cells are
inserted. Open the Battery Compartment as shown in figure 5.
910
Figure 5 Figure 6

Wall Mounting
Select a location. It must be a flat surface such as wall. Place the COGNIFACE
INTEGRA200 at specified height from the ground. There are two possible types of Wall
mounting:
1. Key Slot Mounting
2. Through Slot Mounting
Note: Key slot mounting is recommended due to less complexity.
Close the lid of the battery compartment as shown in figure 7 and tighten those
four screws back into their position with the help of screw driver as shown in
figure 8.
In case of power cut, this will provide battery back-up for minimum 2 hours.
11 12
Figure 7
Figure 8

Installation Instructions-
Key Slot Mounting
Place the mounting template against the wall where Installation is to be done.
Trace four screw holes using mounting template with pen/pencil as shown in
the figure 9 and figure 10 below.
Step-1
14
13
Figure 9 Figure 10

15 16
Step-2
Drill four screw holes(A,B,C,D) along the traced markings with the help of power
drill as shown in figure 11 below.
A
D
C
B
Step-3
Fix the supplied screw grips into the A, B, C and D screw holes as shown in the
figure 12.
A
D
B
C
Figure 11 Figure 12

Step-4
Insert screws into screw holes A, B, C and D having screw grips as shown in
the figure 13 and figure 14.
A
D
B
C
A
D
C
B
17 18
Figure 13 Figure 14

A
D
B
C
19 20
Step-5
Align Key hole slots of COSEC COGNIFACE INTEGRA200 with the screws A, B, C
and D on the wall and slightly slide it downwards as shown in figure 15 and
figure 16.
Figure 15 Figure 16

Through Slot Mounting
Follow Step-1, Step-2 and Step-3 of Key Hole mounting as initial steps of through
Slot mounting.
Step-4
After inserting screw grips, open Six screws(1-6) which are on top and Six
screws (7-12) which are on bottom of COSEC COGNIFACE INTEGRA200 with
the help of screw driver as shown in the figure 17. After opening the screws,
keep them aside carefully as they will be required at the end of through slot
mounting.
Place the mounting template against the wall where Installation is to be done.
Trace four screw holes using mounting template with pen/pencil as shown in
the figure 9 and figure 10.
Step-1
Step-2
Drill those four screw holes(A,B,C,D) along the traced markings with the help of
power drill as shown in figure 11.
Step-3
Fix the supplied screw grips into the A, B, C and D screw holes as shown in the
figure 12.
5
12
11
10
9
8
7
4
3
2
1
6
22
21
Figure 17

Step-5
Upon opening those 12 screws, front enclosure of COGNIFACE INTEGRA200
with ARGO door attached will be separated from the bottom enclosure having
mounting plate as shown in figure 18. Remove DC jack and Power cable of
COSEC ARGO attached to other half-part of enclosure and keep it aside with
caution.
Step-6
Fix four screws in through slots of bottom enclosure. Tighten screw 1 in screw
hole A, screw 2 in screw hole B, screw 3 in screw hole C and screw 4 in screw
hole D with the help of screw driver as shown in figure 19 below.
A
B
14
3
2
D
C
23 24
Figure 19
Figure 18

Step-7
After properly tightening the screws, close the enclosure box by fixing top
enclosure back into its position as shown in figure 20. Before closing it remember
to plug-in DC jack and power cable of ARGO device correctly back into its
position. Tighten those 12 screws back with the help of screw driver as shown in
figure 21.
26
25
5
12
11
10
9
8
7
4
3
2
1
6
Figure 21
Figure 20

Specification
Parameters
Battery Back-up Yes (upto 2 Hours)
User Capacity 50,000
Event Logs
5,00,000
Templates
Capacity 25000 (1:N mode) and 1 lakh (1:1 mode)
Built in Bluetooth
Input Power
12 VDC @2A
Yes BLE (4.2 and above)
0°C to +45°C
Type of Card
Technical Specifications
Operating
Temperature
Credential Support Card, PIN, Finger and Face Recognition
COGNIFACE
INTEGRA200E
COGNIFACE
INTEGRA200M
EM Prox Mifare/Desfire
NFC
Buzzer
Yes
Assigning IP Address and Other
Network Settings
For Face Recognition feature to work successfully, All the devices i.e COSEC
ARGO device, IP Camera-MIDR20FL28CWS and FR module are in same network
by default.
Note:
ŸFor Face recognition, there should be availability of platform and FR Licenses.
ŸAlso check the supporting version of COSEC Server and COSEC desktop
utility- COSEC Enroll installed in computer.
ŸEnsure all licenses are activated
1. Consider the default IP Address of ARGO as: 192.168.50.1, Default IP Address
of IP Camera as 192.168. 3 and default IP of FR module as: 192.168.50.2. 50.
2. Now once all the devices are connected online, Add ARGO door in COSEC
software and assign the users.
3. Configure FR Settings on Door for the users.
27 28
For Configuring FR Settings:
1. Enable Face Recognition feature for User from User Configuration.
2. Assign ARGO door to the user. Ensure that COSEC ARGO Door, FR Module and
IP Camera are in the same subnet.
3. On ARGO Door device configuration page, select the Capturing device as IP
Camera in Video Surveillance section. Configure the MJPEG URL of IP Camera in
Advance Settings.
Built in Wi-Fi Yes

At the end of product life cycle; batteries, soldered boards, metal
components and plastic components must be disposed through recyclers.
If you are unable to dispose-off the products or unable to locate e-waste
recyclers, you may return the products to Matrix Return Material
Authorization (RMA) department.
Disposal of Product after End-Of-Life
The product refered is covered by the waste Electrical and Electronic
Equipment (WEEE) directive and must be disposed of in a responsible
manner.
WEEE Directive 2002/96/EC
www.matrixaccesscontrol.com
Head Office
394-GIDC, Makarpura, Vadodara - 390010, India
Ph: ([phone]
Email: Suppor[email protected]
MATRIX COMSEC
V.1, July, 2020
29
4. For configuring FR settings on ARGO Door, go to ‘Identification Server’ in
Device Configuration page of ARGO. Enable FR and select the Face capturing
mode. Select the FR mode as Local. Enter the FR Server. After all settings are
done, click on “Save”.
For more details, Refer COSEC User Guide.