MATSONIC MS7167D User manual

Mainboard User’s Manual
This publication, including all photographs, illustrations and
software, is protected under international copyright laws, with all
rights reserved. Neither this manual, nor any of the material
contained herein, may be reproduced without the express written
consent of the manufacturer.
The information in this document is subject to change without
notice. The manufacturer makes no representations or warranties
with respect to the contents hereof and specifically disclaims any
implied warranties of merchantability or fitness for any particular
purpose. Further, the manufacturer reserves the right to revise this
publication and to make changes from time to time in the content
hereof without obligation of the manufacturer to notify any person
of such revision or changes.
Trademarks
IBM, VGA, and PS/2 are registered trademarks of International
Business Machines.
AMD and Athlon are registered trademarks of Advanced Micro
Devices Inc.
Intel, Pentium, Pentium-II, and MMX are registered trademarks of
Intel Corporation.
Microsoft, MS-DOS and Windows 95/98/NT are registered
trademarks of Microsoft Corporation.
Sound Blaster is a trademark of Creative Technology Ltd.
PC-cillin and ChipAwayVirus are trademarks of Trend Micro Inc.
Award is a trademark of Award Software Inc.
A3D is a registered trademark of Aureal Inc.
MediaRing Talk is a registered trademark of MediaRing Inc.
Other names used in this publication may be trademarks and are
acknowledged.
Copyright © 2000
All Rights Reserved
MS7167D, V1.5
V133X/August 2000

MS7167 Mainboard User’s Manual
II
Table of Contents
Chapter 1: Introduction................................................................... 1
Key Features ........................................................................... 2
Package Contents.................................................................... 4
Static Electricity Precautions.................................................. 4
Pre-Installation Inspection ...................................................... 4
Chapter 2: Mainboard Installation .................................................. 5
Mainboard Components.......................................................... 6
I/O Ports.................................................................................. 6
Install A CPU.......................................................................... 7
Install Memory........................................................................ 8
Setting Jumper Switches......................................................... 9
Install the Mainboard............................................................ 10
Install Other Devices.............................................................11
Expansion Slots..................................................................... 13
Chapter 3: BIOS Setup Utility...................................................... 15
Introduction........................................................................... 15
Running the Setup Utility ..................................................... 16
Standard CMOS Features Page............................................. 17
Advanced BIOS Features Page.............................................18
Advanced Chipset Features Page..........................................21
Integrated Peripherals Page................................................... 24
Power Management Setup Page............................................ 27
PnP/PCI Configurations Page............................................... 29
Hardware Monitor Page........................................................ 31
Frequency/Voltage Control Page.......................................... 32
Load Best Performance Defaults ..........................................33
Load Optimized Defaults......................................................33
Set Password......................................................................... 33
Save & Exit Setup................................................................. 33
Exit Without Saving.............................................................. 34
Chapter 4: Software & Applications............................................. 35
About the Software...............................................................35
Folders for this Mainboard.................................................... 35
Running the Support CD-ROM ............................................ 36
Utility Folder Installation Notes ........................................... 36
Award Flash Memory Utility.......................................... 36
Mainboard (MS7167D) Installation Notes ........................... 37

MS7167 Mainboard User’s Manual
III
Appendix A: Gamut2000 .......................................................... A1
1. GAMUT2000 Family ...................................................... A2
1.1 LifeAmp - Versatile Audio Playback System ........... A2
1.2 AudioPort - Audio Transportation System ............... A4
2. Installation ...................................................................... A5
2.1 Before Beginning: System Requirements ................. A5
2.2 Uninstalling the Previous of GAMUT2000............... A5
3. Main Console .................................................................. A7
3.1 Introduction ............................................................... A7
3.2 Function and Operation ............................................. A7
3.3 Main Menu ................................................................ A9

1: Introduction
1
Chapter 1
Introduction
This mainboard has a Socket-370 processor socket for an Intel
PPGA/FCPGA Celeron or FCPGA Pentium III processor. You
can install any one of these processors on the mainboard. The
mainboard supports front-side bus speeds of 66MHz, 100MHz or
133MHz.
This mainboard uses the VIA PM133 chipset which provides CPU
Plug & Play through firmware, a 4X AGP slot for highly graphics
display, CPU Plug & Play through firmware, and integrates a
Savage4 2D/3D/Video Accelerator. The mainboard has a built-in
AC97 Codec, provides an AMR (Audio Modem Riser) slot to
support Audio and Modem application. In addition, the mainboard
has an extended set of ATX I/O Ports including PS/2 keyboard
and mouse ports, two USB ports, a parallel port, a VGA port, a
serial port, a game port and audio ports.
This mainboard has all the features you need to develop a powerful
multimedia workstation. The board is ATX size and has power
connectors for an ATX power supply.

MS7167 Mainboard User’s Manual
2
Key Features
The key features of this mainboard include:
Socket-370 Processor Support
♦Supports PPGA/FCPGA Celeron CPUs which provide
Pentium II performance with integrated L1 and L2 cache
♦Supports FCPGA Pentium III CPUs
♦Supports 66MHz, 100MHz or 133MHz Front-Side Bus
All processors are automatically configured using firmware and a
synchronous Host/DRAM Clock Scheme.
Memory Support
♦Three DIMM slots for 168-pin SDRAM memory modules
♦Support for 100/133 MHz memory bus
♦Maximum installed memory is 3 x 512MB = 1.5GB
Expansion Slots
♦One AMR slot for a special audio/modem riser card
♦One AGP4X slot for AGP 2.0-compliant interface.
♦Four 32-bit PCI slots for PCI 2.2-compliant bus interface.
♦One 8/16-bit ISA slot.
Onboard IDE channels
♦Primary and Secondary PCI IDE channels
♦Support for PIO (programmable input/output) modes
♦Support for Multiword DMA modes
♦Support for Bus Mastering and Ultra DMA 33/66 modes
Power Supply and Power Management
♦ATX power supply connector
♦Supports ACPI, previous PMU and suspend switch
♦Supports Wake on LAN and Wake on Alarm

1: Introduction
3
AC97 Codec
♦Compliant PC97 2.1 specification
♦Supports 18-bit ADC (Analog Digital Converter) and DAC
(Digital Analog Converter) as well as 18-bit stereo full-
duplex codec
Onboard I/O Ports
♦Provides PC99 Color Connectors for easy peripheral device
connections
♦Floppy disk drive connector with 1Mb/s transfer rate
♦Two serial ports with 16550-compatible fast UART
♦One parallel port with ECP and EPP support
♦Two USB ports, optional two USB ports module
♦Two PS/2 ports for keyboard and mouse
♦One infrared port connector for optional module
Hardware Monitoring
♦Built-in hardware monitoring for CPU & System
temperatures, fan speeds and mainboard voltages
Onboard Flash ROM
♦Automatic CPU and board configuration
♦Supports Plug and Play configuration of peripheral devices
and expansion cards
♦Built-in virus protection using Trend’s ChipAwayVirus
provides boot process virus protection.
Bundled Software
♦PC-Cillin provides automatic virus protection under
Windows 95/98
♦MediaRing Talk provides PC to PC or PC to Phone
internet phone communication
♦Corel WordPerfect Suite 8 is a Microsoft Windows®
office application suite (optional)
Dimensions
♦Micro ATX form factor (30.5cm x 19cm)

MS7167 Mainboard User’s Manual
4
Package Contents
Your mainboard package ships with the following items:
!The mainboard
!This User’s Guide
!1 UDMA/66 IDE cable
!1 Floppy disk drive cable
!Support software on CD-ROM disk
Static Electricity Precautions
Components on this mainboard can be damaged by static
electricity. Take the following precautions when unpacking the
mainboard and installing it in a system.
1. Keep the mainboard and other components in their original
static-proof packaging until you are ready to install them.
2. During installation, wear a grounded wrist strap if possible. If
you don’t have a wrist strap, discharge static electricity by
touching the bare metal of the system chassis.
3. Handle the mainboard carefully by the edges. Avoid touching
the components unless it is absolutely necessary. During
installation put the mainboard on top of the static-protection
packaging it came in with the component side facing up.
Pre-Installation Inspection
1. Inspect the mainboard for damage to the components and
connectors on the board.
2. If you suspect that the mainboard has been damaged, do not
connect power to the system. Contact your mainboard vendor
and report the damage.

2: Mainboard Installation
5
Chapter 2
Mainboard Installation
To install this mainboard in a system, follow the procedures in this
chapter:
!Identify the mainboard components
!Install a CPU
!Install one or more system memory modules
!Verify that any jumpers or switches are set correctly
!Install the mainboard in a system chassis (case)
!Connect any extension brackets or cables to the mainboard
connector headers
!Install any other devices and make the appropriate connections
to the mainboard connector headers.
Note:
1. Before installing this mainboard, make sure jumper J8 is set to
Normal setting. See this chapter for information on locating J8
and the setting options.
2. Never connect power to the system during installation. Doing
so may damage the mainboard.

MS7167 Mainboard User’s Manual
6
Mainboard Components
Use the diagram below to identify the major components on the
mainboard.
Note: Any jumpers on your mainboard that do not appear in
this illustration are for testing only.
I/O Ports
The illustration below shows a side view of the built-in I/O ports
on the mainboard.
PS/2 Mouse
PS/2 Keyboard
Parallel Port Game/MIDI Port
Serial Port COM1/3
USB Ports Microphone Jack
Line-Out Jack
VGA Port
Line-In Jack

2: Mainboard Installation
7
Install A CPU
This mainboard has a Socket-370 which supports PPGA/FCPGA
Celeron and FCPGA Pentium III processors.
Do not try to install a Socket 7 processor in the Socket-370. A
Socket 7 processor such as the Pentium-MMX, or the AMD K5/K6
does not fit in the Socket 370.
The following list notes the processors that are currently supported
by this mainboard.
FCPGA Pentium III: 500~933MHz, FSB: 100MHz, 133MHz
PPGA/FCPGA Celeron: 300~600MHz, FSB: 66 MHz
Installing a Socket-370 Processor
A processor installs into the ZIF (Zero Insertion Force) Socket-370
on the mainboard.
1. Locate the Socket-370 and FAN1. Pull the locking lever out
slightly from the socket and raise it to the upright position.
2. On the processor, identify the Pin-1 corner by its beveled edge.
3. On the Socket-370, identify the Pin-1 corner. The Pin-1 corner
is at the top of the locking lever when it is locked.
4. Match the Pin-1 corners and insert the processor into the
socket. No force is required and the processor should drop into
place freely.
5. Swing the locking lever down and hook it under the catch on
the side of the socket. This secures the CPU in the socket.
6. All processors should be installed with a combination
heatsink/cooling fan, connect the cable from the fan to the
CPU fan power connector FAN1.
FAN1
Socket-370
Pin-1 Corner

MS7167 Mainboard User’s Manual
8
DIMM1
DIMM3
Install Memory
The mainboard has three DIMM sockets for system memory
modules. You must install at least one memory module in order to
use the mainboard.
For this mainboard, you must use 168-pin, 3.3V unbuffered PC100
or PC133 SDRAM memory modules. You can install any size
memory module from 32 MB to 512MB, so the maximum memory
size is 3 x 512MB = 1.5GB.
The edge connectors on the memory modules have cut outs, which
coincide with spacers in the DIMM sockets so that memory
modules can only be installed in the correct orientation.
To install a module, push the retaining latches at either end of the
socket outwards. Position the memory module correctly and insert
it into the DIMM socket. Press the module down into the socket so
that the retaining latches rotate up and secure the module in place
by fitting into notches on the edge of the module.
DIMM2

2: Mainboard Installation
9
1
Setting Jumper Switches
Jumpers are sets of pins which can be connected together with
jumper caps. The jumper caps change the way the mainboard
operates by changing the electronic circuits on the mainboard. If a
jumper cap connects two pins, we say the pins are SHORT. If a
jumper cap is removed from two pins, the pins are OPEN.
Jumper J8: Clear CMOS Memory
Use this jumper to clear the contents of the CMOS memory. You
may need to clear the CMOS memory if the settings in the Setup
Utility are incorrect and prevent your mainboard from operating.
To clear the CMOS memory, disconnect all the power cables from
the mainboard and then move the jumper cap into the CLEAR
setting for a few seconds.
Function Jumper Setting
Normal Operation Short Pins 1-2
Clear CMOS Memory Short Pins 2-3
Jumper J4: Codec Selector
Use this jumper to select the onboard audio codec or Audio
Modem Riser (AMR) slot.
Function Jumper Setting
Primary codec onboard Short Pins 1-2
Primary codec on AMR slot Open Pins 1-2
J8
J4

MS7167 Mainboard User’s Manual
10
FAN2
Install the Mainboard
Install the mainboard in a system chassis (case). The board is an
ATX size mainboard with a twin-tier of I/O ports. Ensure that your
case has an I/O cover plate that matches the ports on this
mainboard.
Install the mainboard in a case. Follow the instructions provided by
the case manufacturer using the hardware and internal mounting
points on the chassis.
Connect the power connector from the power supply to the PWR1
connector on the mainboard.
If there is a cooling fan installed in the system chassis, connect the
cable from the cooling fan to the FAN2 fan power connector on the
mainboard.
Connect the case switches and indicator LEDs to the CONN1
switch and LED connector header. See the illustration below for a
guide to the header pin assignments.
PWR1
CONN1
22
21
Power LED
Pins 2-4-6
Speaker
Pins 1-3-5-7
Turbo LED
Pins 13-1
4
HDD LED
Pins 15-16
2
1
Reset Switch
Pins 17-18
Power Button
Pins 21-22
Suspend Switc
h
Pins 11-12

2: Mainboard Installation
11
1 1 1
Install Other Devices
Install and connect any other devices in the system following the
steps below.
Floppy Disk Drive
The mainboard ships with a floppy disk drive cable that can
support one or two drives. Drives can be 3.5” or 5.25” wide, with
capacities of 360K, 720K, 1.2MB, 1.44MB, or 2.88MB.
Install your drives and connect power from the system power
supply. Use the cable provided to connect the drives to the floppy
disk drive header FLOPPY.
IDE Devices
IDE devices include hard disk drives, high-density diskette drives,
and CD-ROM or DVD-ROM drives, among others.
The mainboard ships with an IDE cable that can support one or two
IDE devices. If you connect two devices to a single cable, you
must configure one of the drives as Master and one of the drives as
Slave. The documentation of the IDE device will tell you how to
configure the device as a Master or Slave device. The Master
device connects to the end of the cable.
Install the device(s) and connect power from the system power
supply. Use the cable provided to connect the device(s) to the
Primary IDE channel connector IDE1 on the mainboard.
If you want to install more IDE devices, you can purchase a second
IDE cable and connect one or two devices to the Secondary IDE
IDE1 IDE2 FLOPPY

MS7167 Mainboard User’s Manual
12
channel connector IDE2 on the mainboard. If you have two
devices on the cable, one must be Master and one must be Slave.
Internal Sound Connections
If you have installed a CD-ROM drive or DVD-ROM drive, you
can connect the drive audio cable to the onboard sound system.
On the mainboard, locate the two 4-pin connectors CD1 and CD2.
There are two kinds of connector because different brands of CD-
ROM drive have different kinds of audio cable connectors.
Connect the cable to the appropriate connector.
Infrared Port
You can connect an infrared port to the mainboard. You can
purchase this option from third-party vendors.
1. Locate the infrared port IR header on the mainboard.
2. If you are adding an infrared port, connect the ribbon cable
from the port to the header and then secure the port to an
appropriate place in your system chassis.
CD1
CD2
1
J5-IR Header

2: Mainboard Installation
13
Expansion Slots
This mainboard has four 32-bit PCI expansion slots, one AGP, one
AMR slot and one 8/16-bit ISA slot.
Follow the steps below to install a PCI/AMR/AGP/ISA expansion
card.
1. Locate the AGP, AMR, PCI or ISA slots on the mainboard.
2. Remove the slot cover for this slot from the system chassis.
3. Insert the expansion card edge connector into the slot and press
it firmly down into it so that it is fully inserted.
4. Secure the expansion card bracket to the system chassis using
the screw that held the slot cover in place.
AMR Slot
The AMR (Audio Modem Riser) slot is an industry standard slot
that allows for the installation of a special audio/modem riser card.
Different territories have different regulations regarding the
specifications of a modem card. You can purchase an AMR card
that is approved in your area and install it directly into the AMR
slot.
PCI2
PCI1
AGP1
AMR1
ISA1

MS7167 Mainboard User’s Manual
14
Wake On LAN (WOL)
If you have installed a LAN adapter expansion card, connect the
card to the Wake On LAN connector WOL1. This allows
incoming traffic to resume the system from a software power down.
You need to enable this feature in the system setup utility.
WOL1
Header

3: BIOS Setup Utility
15
Chapter 3
BIOS Setup Utility
Introduction
The BIOS Setup Utility records settings and information about
your computer such as the date and time, the kind of hardware
installed, and various configuration settings. Your computer uses
this information to initialize all the components when booting up
and functions as the basis for coordination between system
components.
If the Setup Utility configuration is incorrect, it may cause the
system to malfunction. It can even stop your computer from
booting properly. If this happens, you can use the clear CMOS
jumper to clear the CMOS memory used to store the configuration
information, or you can hold down the Page Up key while you
reboot your computer. Holding down the Page Up key also clears
the setup information.
You can run the setup utility and manually make changes to the
configuration. You might need to do this to configure some of the
hardware that you install on or connect to the mainboard, such as
the CPU, system memory, disk drives, etc.

MS7167 Mainboard User’s Manual
16
Running the Setup Utility
Each time your computer starts, before the operating system loads,
a message appears on the screen that prompts you to “Press
<DEL> to enter SETUP”. When you see this message, press the
Delete key and the Main menu page of the Setup Utility appears on
your monitor.
CMOS Setup Utility – Copyright (C) 1984 – 2000 Award Software
Standard CMOS Features
Advanced BIOS Features
Advanced Chipset Features
Integrated Peripherals
Power Management Setup
PnP/PCI Configurations
Hardware Monitor
Frequency/Voltage Control
Load Best Performance Defaults
Load Optimized Defaults
Set Password
Save & Exit Setup
Exit Without Saving
Esc : Quit F9: Menu in BIOS ↑
↑↑
↑↓
↓↓
↓→
→→
→←
←←
←: Select Item
F10 : Save & Exit Setup
Time, Date, Hard Disk Type . . .
Listed below are explanations of the keys displayed at the bottom
of the screens:
Key Function
Esc Escape key: Exits the current menu
←
←←
←↓
↓↓
↓↑
↑↑
↑→
→→
→Cursor keys: Scroll through the items on a menu
+/−/PU/P
DPlus, minus, Page Up and Page Down keys:
Modify the selected field’s values
F10 F10 key: Saves the current configuration and exits
setup
F1 F1 key: Displays a screen that explains all key
functions
F5 F5 key: Loads previously saved values to CMOS
F6 F6 key: Loads a best performance configuration
for the normal system.
F7 F7 key: Loads an optimum set of values for peak
performance