MATTRESS FIRM 600 User manual

Adjustable Base
setup guide
n300/600 nK/CK Sectional Base
x2 - T-Spacers
x4 - 3-Inch
Carriage Bolts
and Nuts
x1 - Remote
Control (varies
according to
base type)
x6 - Pin-adjustable
Legs
x1 - Mattress
Retainer
x3 - AAA
Batteries
x1 - WRENCH
x2 - Center
Support
Brackets
HEAD FOOT
HEAD FOOT
MEM FLAT
300 600
FLAT
ZGRAV
SNORE
M2
M1 SET
ON/OFF
FOOTHEAD
FOOTHEAD PILLOW
M3 M4
READ ALL INSTRUCTIONS BEFORE USING.
DUE TO RISK OF INJURY, TWO ADULTS ARE
REQUIRED TO HANDLE AND MOVE ADJUSTABLE
BASE.
WARNING
!
STEP 1
Remove top of shipping carton. Verify contents; inspect for
damage.
291-0070-b EDR15140 5/19
© 2019 Mattress Firm, Inc.

2
SETUP
BE CAREFUL USING SHARP INSTRUMENTS. INJURY
IS POSSIBLE IF TOOLS ARE NOT USED PROPERLY.
CAUTION
!
STEP 3
Carefully lift base head section out of shipping carton and
place on clean surface (FIGURE 2).
Remove the divider from shipping carton.
Carefully lift base foot section out of shipping carton and
place adjacent to head section (FIGURE 2).
Slide head and foot sections together making sure to align
mounting holes (center of base sections) (FIGURE 2).
STEP 2
Cut zip-tie from electrical power supply. Cut (2) zip-ties
and remove mattress retainer (set aside) (FIGURE 1).
PINCH POINT WARNING!
KEEP HANDS AND FINGERS CLEAR WHEN SLIDING
BASES TOGETHER.
WARNING
!
FIGURE 2
FIGURE 1

3
SETUP
STEP 4
Place a T-Spacer in between the mounting points (each side of base). Line up the
holes in the T-Spacers with the holes in the mounting points (FIGURE 3).
Place a center support bracket over the mounting points on each side of base.
Insert carriage bolts through the square holes in the center support bracket.
Install nuts on carriage bolts (FIGURE 3). HAND TIGHTEN.
After all hardware is installed, tighten all nuts using provided wrench.
FIGURE 3

4
STEP 5
Route FOOT MOTOR CABLE underneath base frame and
connect to HEAD MOTOR CABLE (FIGURE 4).
600 MODEL ONLY - Route FOOT MASSAGE MOTOR
CABLE underneath base frame and plug into control box
(FIGURE 4).
Extend electrical power cord out head end of base.
POWER CORDS MUST NOT INTERFERE WITH ANY
ADJUSTABLE BASE MECHANISMS.
WARNING
!
FIGURE 4

5
STEP 6
Screw (4) legs into the threaded inserts at the corners of the base frame
(FIGURE 5).
Screw (2) legs into the threaded inserts of the center support brackets
(FIGURE 5).
Push pin in to adjust leg height (6 inches to 10 inches).
Note: When adjusting legs, make sure base sets level on oor.
FIGURE 5
STEP 7
Rotate base over onto its legs.
Remove remaining packaging. DUE TO RISK OF INJURY, TWO ADULTS ARE
REQUIRED TO HANDLE AND MOVE ADJUSTABLE
BASE.
WARNING
!

6
SETUP
STEP 8
Install (3) batteries in remote control.
Plug power cord into power outlet. Note: An electrical
surge protection device is recommended (not included).
Operate remote control to test base functions (FIGURE 6)
(see separate Syncing Guide).
STEP 10
Install the mattress retainer at the foot end of the
base.
Place one end of the mattress retainer into the
outside hole of the left insert and place the other
end into the outside hole of right insert (FIGURE 7).
FIGURE 7
HEAD FOOT
HEAD FOOT
MEM FLAT
STEP 9
Lower base to at position.
FLAT
ZGRAV
SNORE
M2
M1 SET
ON/OFF
FOOTHEAD
FOOTHEAD PILLOW
M3 M4
300
600
FIGURE 6

7
STEP 11
Place mattress on base to complete assembly.
Note: If adjustable base will not operate, refer to the Troubleshooting section of the
owner’s manual. To download a copy of the owner’s manual, visit
https://lpadjustablebeds.com/om/mattressrm or call Mattress Firm at 844-628-8376.
To register your adjustable base, please go to https://lpadjustablebeds.com/register
or call Mattress Firm at 844-628-8376.
SETUP