Max Pro MOHI JL-1002 User manual

MANUAL

HOT AIR STYLER SETS : JL-1002
220-240V~ 50/60Hz 1200W
Instruction Manual
Dear Customer,
Thank you for buying this hot air styler .
You may already be familiar with using a hot air styer but
do please take time to read these instructions. They are
designed to familiarize you with the unit’s features and to
ensure you get the very best out of your purchase.
Safety is important!
Your safety and the safety of others is important. Please,
therefore, ensure you read the safety instructions before you
operate this hot air styler
Kind regards,
Team Max Pro

Read all the safety instructions before rst use of your hot
air styler
WARNING: THIS HOT AIR STYLER UNTIL THE POWER
IS DISCONNECTED AT THE MAINS. TO AVOID RISK OF
ELECTRIC SHOCK: 220-240V~ 5
Do not use this device in a bathtub, shower, or
water-lled reservoir
1] WARNING: Do not use this appliance near bathtubs,
showers, basins or other vessels containing water.
2] WARNING: Do not use this appliance near water.
3] The airborne noise emitted by the appliance ≤90 dB(A).
4] When the hot air styler is used in a bathroom, unplug
it after use since the proximity of water presents a hazard
even when the hairdryer is switched o.
5] For additional protection, the installation of a residual
INSTRUCTIONS

current device (RCD) having a rated residual operating
current not exceeding 30 mA is advisable in the electrical
circuit supplying the bathroom. Ask your installer for advice.
6] The appliance is not to be used by persons (including
children) with reduced physical, sensory or mental capabili-
ties, or lack of experience and knowledge, unless they have
been given supervision or instruction.
7] Children being supervised not to play with the appliance.
8] If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualied persons
in order to avoid a hazard.
9] Always unplug the hot air styler after use.
10] Do not use or store the hot air styler where it can come
into contact with water.
11] If the appliance falls into water, UNPLUG IT
IMMEDIATELY. Do not reach into the water until the power

has been disconnected.
12] This hot air styler should never be left unattended when
plugged in.
13] Do not pull or wrap power cord around the hot air styler.
14] Close supervision is necessary when this appliance is
used by, on , or near children.
15] Do not use attachments not recommended by the
manufacturer.
16] Never operate the hot air styler if it has a damaged
cord or plug or if it has been dropped into water. Return the
appliance to a service centre for examination and repair.
17] Keep the cord away form heated surfaces.
18] Never block the air vents at the rear of the hairdryer, or
place it on a soft surface where the air vents free of dust,
hair, etc. Do not insert any objects into the air vents.
INSTRUCTIONS

19] Do not use outdoors, or where aerosol products are
being used.
20] Do not direct hot air toward eyes.
21] Attachments may get hot in use. Use care when
handling them.
22] Do not put the hot air styler down while it is operating.
23] Check that the voltage rating of this appliance matches
that of your supply.
24] If the appliance falls into water, UNPLUG IT
IMMEDIATELY. Do not reach into the water until the power
has been disconnected.
25] Do not use the appliance if the power cord is damaged.
It must be replaced by the manufacturer, the aftermarket
service or by a suciently qualied person in order to
prevent any risk of an accident.
-

IMPORTANT
The mains lead of this appliance is not replaceable by the
user. If the supply cord is damaged, it must be replaced
by the manufacturer, its service agent or similarly qualied
persons in order to avoid a hazard.
Safety considerations: Position the power supply lead so
that it is not likely to be walked on or pinched by things
placed on or against them. Do not use the hot air styler
in humid or damp conditions. Do not allow the appliance
to get wet i.e. dripping or splashing, as this may be
dangerous.
Ventilation: The slots and openings on the appliance are
for ventilation. Do not cover or block them as it could lead
to overheating. NEVER let children push anything into the
holes or slots on the hot air styler .
INSTRUCTIONS

1] 0-I-II Switch
2] I-II-Ⅲ Switch
3] Handle
4] Power cord
5] Release button
6] Round roll brush
7] Pad air brush
8] Concentrator
9] Big roll brush

ASSEMBLY | Clip the concentrator onto the front of the
hairdryer (if required).
SWITCHING ON | Mains power * Unwind the power cable
and plug into the mains socket and switch on * Set the On/
O switch to the required settings (1 or 2) * Position 2 is
more heater than position 1.
SWITHING OFF | When you have nished, set the On/O
switch to the o (0) position.
OPERATION STYLING GUIDE |
1] Shampoo and condition your hair. Rinse the hair thoroug-
hly. Towel blot hair to remove excess moisture. Divide your
hair into sections. Using the dryer along with a styling brush,
direct hot air through a section of hair at a time. Move dryer
steadily across each section so that hot air passes through
hair. Direct air ow at hair, not scalp.
2] Keep dryer’s air intake vents unobstructed and free from
from hair while dryer.
3] To avoid over-drying, do not concentrate heat on any
one section for any length of time. Keep the dryer moving
INSTRUCTIONS

as you style.
4] For quick styling, dampen hair with a mist of water before
styling with the dryer.
5] When using the dryer to create curls and waves, dry hair
almost completely on the warmest setting, then nish styling
using the lower setting. This will set the style in your hair.
6] This dryer includes a concentrator attachment. Use the
concentrator when you need to focus the drying power in a
small area (such as a curl or a wave) or when you want to
relax curly hair.
IMPORTANT | Before you do any of the following, make
sure the hot air styler is unplugged from the mains supply.
CLEANING | Do not use liquid or aerosol cleaners.
Clean your appliance with a soft, damp (not wet) cloth.
The Multi Airstyler doesn’t work?
1] Make sure it is plugged into the main supply and switch
on.
2] Make sure the ON/OFF button is on.
3] Check the fuse in the plug (see Electrical Information).