Maxima M-ICE 15 User manual

Spangenberg International B.V. –Nijverheidsweg 19F –3641 RP Mijdrecht –Holland –T. [phone] –F. [phone]
[e-mail] - www.maximaholland.com
MAXIMA
ICE CUBE MAKER
USER MANUAL
GEBRUIKSHANDLEIDING
BEFORE USING THIS PRODUCT YOU SHOULD READ THIS USER MANUAL PROPERLY
ALVORENS U DIT PRODUCT IN GEBRUIK GAAT NEMEN DIENT U EERST AANDACHTIG DEZE GEBRUIKSHANDLEIDING
DOOR TE LEZEN

Spangenberg International B.V. –Nijverheidsweg 19F –3641 RP Mijdrecht –Holland –T. [phone] –F. [phone]
[e-mail] - www.maximaholland.com
ENGLISH
Introduction
Thank you for purchasing this Maxima product. In order to obtain the maximum benefit and safe use of this
product, please read these instructions completely before attempting to install or use this product.
Your new Maxima product is manufactured with advanced production techniques. Every product is inspected
before shipment and tested to ensure operator safety and product quality. All parameters have reached or
exceeded the national standard.
The Maxima Ice Maker range produces consistent quality ice cubes or flaked ice for use in food or beverages.
At Maxima we are very proud of our products and are completely committed to providing you with the best
products and service possible. Your satisfaction is our number one priority.
We know you will enjoy using this product and Thank You for choosing our product. We hope you consider
Maxima for your future equipment purchases.
NEDERLANDS
Introductie
Bedankt voor het aanschaffen van dit Maxima product. Deze instructies dienen volledig gelezen te worden
voordat u dit product gaat installeren of gebruiken. Op deze manier kunt u optimaal en veilig van dit product
gebruik maken.
Uw nieuwe Maxima product is geproduceerd met geavanceerde productietechnieken. Elk product wordt voor
verzending geïnspecteerd en getest om veiligheid en betrouwbaarheid te kunnen waarborgen. Alle parameters
voldoen volgens de nationale standaarden.
De Maxima Ice Maker serie produceert ijsblokjes of schilferijs van consistente kwaliteit voor gebruik in voedsel of
dranken.
Bij Maxima zijn wij erg trots op onze producten en zijn volledig gecommitteerd om u van de beste producten en
service te voorzien. Uw tevredenheid is onze nummer 1 prioriteit.
Wij weten dat u met plezier dit product zal gaan gebruiken en bedanken u voor uw keuze. Wij hopen dat u
Maxima in gedachten houdt bij toekomstige aanschaf van apparatuur.

Spangenberg International B.V. –Nijverheidsweg 19F –3641 RP Mijdrecht –Holland –T. [phone] –F. [phone]
[e-mail] - www.maximaholland.com
ENGLISH
Specifications
Model
Production
(kg/24h)
Ice Storage
(kg)
Power
Input
Dimensions
(mm)
Weight
(kg)
Inside Material
Casing
Material
M-ICE 15
15
0.8
230v / 50hz
110w
370x335x280
10
ABS + PC
ABS
M-ICE 24
24
5
230v / 50hz
200w
330x470x580
21
ABS
18/8 Stainless
Steel
M-ICE 28
28
7
230v / 50hz
240w
398x510x610
26
ABS
18/8 Stainless
Steel
M-ICE 45
45
7
230v / 50hz
280w
398x510x610
28
ABS
18/8 Stainless
Steel
M-ICE 60
60
14
230v / 50hz
370w
398x510x785
37
ABS
18/8 Stainless
Steel
M-ICE 80
80
25
230v / 50hz
420w
500x612x908
48
ABS
18/8 Stainless
Steel
M-ICE 30
FLAKE
30
7
230v / 50hz
215w
330x470x580
28
ABS
18/8 Stainless
Steel
M-ICE 50
FLAKE
50
10
230v / 50hz
230w
398x542x716
43
ABS
18/8 Stainless
Steel
M-ICE 85
FLAKE
85
20
230v / 50hz
470w
398x510x832
46
ABS
18/8 Stainless
Steel
Safety Regulations
•The machine may only be used for the purpose for which it was intended and designed. The manufacturer is
not liable for any damage caused by incorrect operation and improper use.
•This machine may only be used for its intended purpose: Making ice cubes or flakes.
•Keep the machine and electrical plug away from water and any other liquids. In the unlikely event that the
machine should fall into water, immediately pull the plug out of the socket and have the machine checked
by a certified technician. Not following these instructions may cause life-threatening situations.
•The device is to be used indoors only.
•Do not move the appliance while operational.
•Do not cover or place objects on top of the appliance when its operating.
•Never try to open the casing of the machine yourself.

Spangenberg International B.V. –Nijverheidsweg 19F –3641 RP Mijdrecht –Holland –T. [phone] –F. [phone]
[e-mail] - www.maximaholland.com
•Do not insert any objects in the casing or openings of the machine.
•Do not touch the power plug with wet or damp hands.
•Do not use the machine after it has fallen or is damaged in any other way. Have it checked and repaired by a
certified engineer.
•Do not try to repair the machine yourself. This may cause life-threatening situations.
•Make sure the cord does not come in contact with sharp or hot objects and keep it away from open fire. To
pull the plug out of the socket, always pull on the plug and not on the cord.
•Keep the cable away from operating range. Do not lay over carpets or heat insulation an do not cover the
cable.
•Always keep an eye on the machine when in use.
•Never put your hands near the moving parts of the machine.
•Never let children use professional machines without supervision.
•Always pull the power plug out of the socket when the machine is not being used.
•ATTENTION! As long as the power plug is in the socket the machine is connected to the power source.
•Keep all packaging away from children. Dispose of packaging in accordance to the regulations of local
authorities.
•Turn off the machine before pulling the power plug out of the socket.
•Never try to move or carry the machine by the power cord.
•Do not use any extra devices that are not supplied along with the machine.
•Avoid overloading the machine.
•Do not place the machine on its side, upside-down or tilt the appliance more than 45° from the vertical. Also
not while the appliance is being transported.
•The electrical installation must satisfy the applicable national and local regulations.
•Change the water regularly to ensure good quality ice cubes. (M-ICE 15 only)

Spangenberg International B.V. –Nijverheidsweg 19F –3641 RP Mijdrecht –Holland –T. [phone] –F. [phone]
[e-mail] - www.maximaholland.com
First Time Use
•Unpack and inspect your machine immediately after receipt. If there are any latent defects or damage to
the machine then immediately contact your dealer. Save all packaging materials in case the machine needs
to be returned or for inspection by the freight carrier.
•Remove any protective film from all surfaces.
•Read this instruction manual completely before attempting to install and operate this product. All
installations and set ups must be done by authorized service agents, your dealer, or Maxima
representatives.
•The machine must be positioned on a flat surface with sufficient space around the machine to allow for easy
access, cleaning and proper ventilation.
•Level and position the machine in such a way that the plug is accessible at all times.
•If your machine is supplied with a factory fitted molded plug then you may plug the unit into a standard
electrical outlet. Make sure that the voltage of the machine and the wall outlet are compatible. If your
machine is not supplied with a factory fitted molded plug then a qualified electrical technician must be
contracted to wire the unit to the power supply.
•Before using your machine for the first time it is recommended that the exterior of the machine is wiped
down with a damp cloth, and the worksurfaces, attachments or attributes are cleaned using a food safe
cleaning detergent and rinsed with warm water. After cleaning, wait for appliance to dry completely.
M-ICE Series Accessories

Spangenberg International B.V. –Nijverheidsweg 19F –3641 RP Mijdrecht –Holland –T. [phone] –F. [phone]
[e-mail] - www.maximaholland.com
Installation
1. Remove the Ice Spoon, Water Inlet Tube, Water Drainage Pipe and Sealing Washers from the ice storage
cabinet. (does not apply for M-ICE 15)
2. Choose a surface where the ice maker is not exposed to direct sunlight, or close to a direct source of heat
such as a cooker, oven or radiator.
3. When placing the ice maker, make sure the power cable is accessible at all times.
4. When positioning the Ice Maker, maintain a distance of 10cm (4 inches) between the appliance and walls or
other objects for ventilation. Increase this distance if the obstacle is a heat source.
5. If necessary, adjust the screw legs to level the machine. The Ice Maker may operate less efficiently if not
level.
6. Set up the device near a water supply connection. (does not apply for M-ICE 15)
7. Connect one end of the water drainage pipe to the water outlet at the rear of the Ice Maker. Attach the
other end of the pipe to a water sewage pipe or container suitable for collecting waste water. (does not
apply for M-ICE 15)
8. Connect one end of the water inlet tube to the machine and the other end to your fresh water supply. Make
sure to put sealing washers in both ends of the tube before connecting them. (does not apply for M-ICE 15)
9. After placement, leave the appliance in its current position for at least an hour to let the refrigirant
precipitate. After this period, plug in the power cable.
10. When the appliance is moved to another location it needs time to acclimatize. (the appliance needs to
adjust to the change in temperature). Allow the appliance to do so for several hours. The ambient
temperature should not be below 6 °C.
M-ICE 15 Structure

Spangenberg International B.V. –Nijverheidsweg 19F –3641 RP Mijdrecht –Holland –T. [phone] –F. [phone]
[e-mail] - www.maximaholland.com

Spangenberg International B.V. –Nijverheidsweg 19F –3641 RP Mijdrecht –Holland –T. [phone] –F. [phone]
[e-mail] - www.maximaholland.com
Operation
•Plug the power plug into the main socket.
•Use the “ON/OFF” button, which is located on the control panel at the front of the appliance to start the
appliance. The red indicator will light up and the production of ice cubes will begin. The first time the
machine is switched on it will perform a self-inspection, this will take approximately 5 minutes.
•The “RUN” indicator will not immidately light up when you switch on the machine for the first time, it will
light up when the compressor is operational.
•Remove the ice basket and fill the water reservoir until it reaches the “MAX” marker. (M-ICE 15 only)
•Choose ice cube size using the “Select” button. The indicators on the control panel will display which size is
selected; “S” (small), “M” (medium), “L” (large). (M-ICE 15 only)
•ATTENTION: When using the Ice Maker for the first time (or after a long period of inactivity) please discard
the first two batches of ice. This process will clean the internal system and ensure clean ice cubes.
•As soon as the ice storage container is full, the “ICE FULL” indicator on the display panel will light up and the
ice maker will stop automatically. Production resumes once ice has been removed from the container.
•To remove the ice cubes, take out the ice basket. Remember to place it back in the original position. (M-ICE
15 only)
•ATTENTION! If the water supply is insufficient, the “WATER LOW” indicator will light up and the ice maker
will stop operation automatically. Check the water inlet or resevoir.
•To drain the water, remove the drain plug located underneath the appliance. (M-ICE 15 only)
•ATTENTION! In event of an error the indicator “Fault” lights up and the machine will switch off
automatically.
•ATTENTION! Do not activate the machine immediately after it has turned off automatically. Wait 3-5
minutes to prevent damage of the compressor.
•When the appliance is not being used, turn off the machine by pressing the ‘On/Off’ button on the control
panel.
•If the appliance will not be used for a longer period, please remove the plug from the main socket. Remove
the water from the reservoir using the drain located at the back of the appliance. Completely dry the water
reservoir using a dry towel.

Spangenberg International B.V. –Nijverheidsweg 19F –3641 RP Mijdrecht –Holland –T. [phone] –F. [phone]
[e-mail] - www.maximaholland.com
CONTROL PANEL M-ICE SERIES
CONTROL PANEL M-ICE 15

Spangenberg International B.V. –Nijverheidsweg 19F –3641 RP Mijdrecht –Holland –T. [phone] –F. [phone]
[e-mail] - www.maximaholland.com
Troubleshooting (for user and technician reference)
This Ice Maker has a self-checking function, faults will be visable on the display panel by use of indicator lights.
The follow overview will help you understand the control panel and possible problems. However, only qualified
engineers should attempt to open or repair the machine. Contact your supplier when in doubt.
Note: If any problems occur, please wait untill the machine stops automatically.
Problem
Possible Cause
Possible Solution
The appliance does not work.
(no indicator lights illuminated)
•The appliance is switched off.
•The power supply is
interupted.
•The voltage is not correct.
•The ambient temperature is
below 6 °C.
➢Switch on the appliance.
➢Check the power supply, plug
in power cable.
➢Use another power source.
➢Make sure the ambient
temperature is above 6 °C.
The appliance does not work.
(only powerswitch is illuminated)
•The voltage is not correct.
•PCB Board is damaged.
➢Use another power socket.
➢Contact supplier
The appliance does not work.
(“ICE FULL” indicator is
illuminated)
•Ice storage container is full.
➢Remove ice from container.
The appliance does not work.
(“ICE FULL” and “FAULT”
indicators are illuminated)
•Ice sensor defective or
disconnected.
➢Replace or connect sensor
The appliance does not work.
(“FAULT” indicator is illuminated)
•Condenser sensor defective or
disconnected.
➢Replace or connect sensor
“WATER LOW” and “ICE FULL”
indicator flash together or
“FAULT” indicator flashes rapidly.
•Refrigerant leakage.
•Compressor does not run.
•Ambient temperature is below
6 °C
➢Check and refill.
➢Check compressor.
➢Keep ambient temperature
above 6 °C
“WATER LOW”, “ICE FULL” and
“FAULT” indicators all flash slowly.
•HALL sensor defective or
positioned incorrectly
•Paddle motor defective
➢Replace or reposition sensor.
➢Replace motor
“FAULT” indicator flashes rapidly
(after period of operation)
•Ice turning motor damaged.
•Micro-switches do not
function.
•Water resevoir damaged.
•Water resevoir bocked by ice.
➢Replace motor.
➢Replace or adjust switches.
➢Replace water resevoir.
➢Remove ice.
The “WATER LOW” indicator is
flashing.
•The water supply is
interupted.
•The water pressure is not
sufficient.
•There is insufficient water in
the water resevoir
•The water filter is blocked.
•The water supply hose is
kinked/twisted.
➢Check the water supply and
sealing ring.
➢Check the water pressure. It
should be between 2 and 3
bar.
➢Add water to the water
resevoir.
➢Remove and clean the filter.
➢Unkink/untwist the hose.
The “WATER LOW” indicator is
illuminated.
•Appliance was without water
supply for more than 24 hours.
➢Check water supply and restart
appliance.
The compressor does not work.
•The ice storage bin is full.
•The water supply is
insufficient.
➢Remove ice from the bin.
➢Check the water inlet.
➢Clean or replace the sensor.