Maxmeen MG-1200ZURE User manual

Security Precautions
Carefully READ the instruction in this manual before use.
Carefully OBSERVE the INSTRUCTION in this manual regarding safety symbols and
messages.
Please KEEP this user MANUAL nearby for reference.
Safety symbol and Message Conventions
Below-described safety symbol and messages are to prevent bodily injury and property
damage. Before operating the amplifier, read this manual first so you completely knowing the
potential safety hazard and understand the meaning of the safety symbols and messages.
WARNING Indicates a potentially hazardous situation, which,
if mishandled, could result in death or serious
bodily injury, and/or property damage.
Indicates a potentially hazardous situation, which,
if mishandled, could result in moderate or minor
bodily injury, and/or property damage.
CAUTION
WARNING
■
●
When Installing the Amplifier
DO NOT install or mount the amplifier in unstable locations, such as slanted surface. It may
result in the amplifier falling down and causing bodily injury and/or property damage.
●Be sure to ground to the safety ground (earth) terminal to avoid electric shock. Never ground
to a gas pipe for tragic disaster may occur.
Use the amplifier only with the voltage specified on the amplifier. Using the voltage higher than
specified may cause fire or electric shock.
●
DO NOT cut, twist, damage, nor modify the power supply cord. In addition, avoid using the
power cord close to heaters, and don't place heavy objects, including the amplifier itself, on
the power cord, for it may cause fire or electric shock.
●
DO NOT expose the amplifier to rain or the environment where it may be splashed by water or
other liquids, for doing so, it may cause fire or electric shock.
●
10
1
Instruction Diagram For Connection

CAUTION
■ When Installing the Amplifier
●DO NOT remove nor plug in the power supply plug with wet hands, for it may cause electric
shock.
●When you unplug the power supply cord, be sure to grasp the power supply plug. DO NOT
pull on the cord itself. Operating the amplifier with damaged power supply cord may cause
fire or electric shock.
●Avoid installing the amplifier in humid or dusty places, the area exposed to the direct sunlight,
locations generating smoke or steam, or near heaters. It may result in fire or electric shock.
●When moving the amplifier, be sure to remove its power supply cord from the wall outlet.
Moving the amplifier with the power cord connected to the outlet may cause damage to the
power cord, and resulting in fire or electric shock. When removing the power cord, be sure to
grasp its plug to pull.
2
9
Pre-output
The output terminal is on the rear panel. The equipment provides 2 pre-output ( level
0dB ), All are mono RCA jack.
Operation
After all connections are completed, and master volume control is at proper position (not
at maximum position). Then turn all line-in input volume controls at proper position. Then
, switch on the power switch. If necessary, turn the bass, treble, and volume control to
what you desire.
Before using the microphone, make sure the corresponding volume control of MIC is at
proper position (not at maximum position). If necessary, adjust the volume further.
Connection
Microphone Connection
Mic1~4 inputs are 6.35mm jack.
Aux Connection (Input)
The equipment provides 4 auxiliary inputs, All are mono RCA jack.
SLEEVEPIN
RCA plug connector
Output Connection
The output terminal is on the rear panel. The terminal connection can connect low
impedance 8 ohm, or high-level 70V or 100V speaker. Use only one of these output
connections for corresponding speaker.
Record Output Connection
If there is the demand of recording, connect the input of the recorder to the record output
on the rear panel of the amplifier.
DC Power Source
Battery Connection (24Vdc)
When using external batteries, ground the amplifier via the screw terminal. (Electrical
stability of the system will be improved by providing a good earth ground.) When
connecting batteries, please ensure correct polarity.
Power Source
AC Power Source
The supply transformer has been designed for use AC 220~240V / 60 Hz.
The amplifier falls.
Amplifier is malfunction.
Water or any metallic object gets into the amplifier.
Smoke or strange smells coming from the amplifier.
The power cord is damaged, such as exposure of the core, disconnection etc..
●DO NOT put cups, bowls, or other containers with liquid or metallic object in it on the top of
the amplifier. If they spill accidentally into the amplifier, it may result in fire or electric shock.
●DO NOT touch the power supply plug during thunder and lightning, for it may result in electric
shock.
●DO NOT insert or drop the metallic objects or flammable materials into the ventilation slots of
the amplifier, for it may result in fire or electric shock.
●DO NOT open nor remove the amplifier cover to prevent fire or electric shock, for there are
high voltage components inside the amplifier.
■
●
When using the Amplifier
When below irregular situation occurs during amplifier use, immediately switch off the power,
disconnect the power supply plug from the AC outlet. Don't try to operate the amplifier again.
Contact your local dealer to check the amplifier.
2U height.
AC or DC power in.
Build in 5 zone and all zone select.
Build in digital recorder player.
Record output.

8
3
Besides AC power source, our mixer amplifier also accept DC 24V input power source
from the battery.
To ensure the amplifier safety, it has speaker short, over temperature, and over load
protection.
The output connection covers low impedance 8 ohm, and high level 70V and 100V or 5
zone and all zone select screw terminal. Choose only one of these output connections
to match the speaker. Furthermore, the amplifier also has one record output for the
demand of recording. The equipment provides 2 Pre-output ( level 0dB ).
Each microphone input and line-in input has its own volume control. The microphone
inputs are at the rear panel. Besides, there are 1 Master control of output volume, and 2
tone controls: Bass and Treble.
MG-1200ZURE & MG-2400ZURE, are mixer amplifiers designed for up to 4 microphones
plus 4 AUX line-in (AUX1~4), total 8 inputs application.
Description
Individual volume control of each input.
Master volume, Bass, and Treble control for the output.
8 ohm, 70V and 100V output.
Product Feature
Build in 4 sets of auxiliary input control circuit.
Build in 2 sets of Pre-output terminals.
Build in 4 sets of independent microphone input control circuit.
Build in microphone priority function on microphone inputs 1 & 2.
Build in overload, overheat & shortage protection circuits.
Multi-input Mixer Amplifier.
■ When using the Amplifier
●Make sure that the volume control is turned to minimum position before power is switched on.
Loud sound produced at high volume when power is switched on may impair hearing.
●
●
●
DO NOT place heavy objects on the amplifier, for it may cause it to fall and may result in body
injury and/or property damage. Besides, the object itself may cause damage or body injury.
DO NOT operate the amplifier for the extended period of time with the sound distorting. It is
an indication of malfunction, which can cause heat and result in fire.
Switch the power off, and unplug the power supply plug from the AC outlet for safety
purposes, when cleaning or leaving the amplifier unused for 7 days or more. Fire or electric
shock may occur.
●If the dust accumulates on the power supply plug or in the wall AC outlet, fire may result in.
Clean it periodically. In addition, make sure the plug is inserted in the wall outlet securely.
●Contact your local dealer to clean the dust, if the dust has accumulated in the amplifier for a
long period of time. Dust accumulation may result in fire or damage.
●DO NOT block the ventilation slots of the amplifier chassis. It will cause the temperature to
rise and result in fire.
Each microphone Build in echo. The microphone echo it has effect ( delay and repeat )
controls. (400~600ms delay time)
Furthermore, the amplifier also has Build in Digital Recorder Player.

4
7
1
2
EXTERNAL 24V DC POWER (BATTERY) INPUT.
8Ω LOW IMPEDANCE OUTPUT.



REC
OUT
L
R
AUX I NPUTMIC I NPUT
MIC 1 MIC 2 MIC 3 MIC 4 VOL . VOL .
24V
BATT I N
5 4 3 2 1
Zon e 1 ~ 5 Outpu t AC IN PUT
AC FU SE


Seria l no:
MODEL : MG-2400 ZURE
POWER OUTPUT : 240W RMS
AC : 220-240V 60Hz DC : 24V
POWER CONSUMPTION : 495W
220-240V 60Hz
0 dB
OUTPUT
( )
USE ONLY WITH A 250V FUSE

ALL
6789
1 2 3 4 510
Back Panel Description
6
1
Front Panel Description
ON
OFF
       
0
25
50
75
100

POW ER
1 2 3 4 5 ALL
Zone Control
MI C 2MI C 3AU X 1 MI C 1
PR IO RIT Y PR IOR IT Y
AU X 2AUX 3/DPLTR EBL EBA SS
EC HORE PE ATDE LA Y
TO NE CO NT ROL AU X VOL UM E MI C VOL UM E
ON
OFF
PR OF ES SI ON AL P UB LI C AD DR ES S MI XE R AM PL IF IE R
MG-2400 ZURE
ZO NE CO NTR OL US B/S D PLAY ER D IGI TAL RE COR DIN G ECH O
EC HO EF FE CT
US B
DE L REC PLAY RE CRP T
PO WER SENSOR
MA ST ER
VO LU ME
MADE IN TAIWAN
2 3 4 5
61 8
9
ON/OFF & OUTPUT LEVEL INDICATOR LED.
POWER SWITCH.
2
TREBLE & BASS TONE CONTROL.
3
AUXILIARY 1 ~ 3 VOLUME CONTROL.
4
MICROPHONE 1 ~ 3 VOLUME CONTROL.
5
※MIC 1 & 2 BUILD IN WITH PRIORITY CIRCUITS.
MASTER VOLUME CONTROL.
7ECHO EFFECT CONTROL.
7
9DIGITAL AUDIO RECORDING DEVICE DISPLAY AND CONTROL AREA.
※PLEASE CHECK: DIGITAL RECORDER PLAYER INSTRUCTION MANUAL
8ZONE CONTROL 1 ~ 5 AND ALL.
15
14
13
12
11
10
9
8
7
1
2
3
4
5
6
Remote control Function Instruction

6
5
10 WHEN THE MUSIC STOP, PRESS
BUTTON BEGIN TO PLAY MUSIC, WHEN THE MUSIC IS PLAYING,
PRESS
BUTTON TO PAUSE THE MUSIC & PRESS IT AGAIN FOR CONTINUE PLAYING.
11 PRESS REC PLAY BUTTON, THE DEVICE WILL PLAY THE RECORDED SOURCE FROM THE RECORD
FILE.
12 WHEN THE MUSIC IS PLAYING, PRESS
BUTTON TO STOP MUSIC PLAYING.
1ON GOING MUSIC PROCEEDING TIME.
2SD CARD / USB DRIVE SYMBOL DISPLAY.
3ON GOING MUSIC OVERALL TIME.
4SINGLE MUSIC REPEAT, OVERALL MUSIC REPEAT &
RANDOM PLAY SYMBOLS DISPLAY.
5
6
POWER ON/OFF SWITCH. LONG PRESS TO THE BUTTON WILL TURN ON THE POWER OF DEVICE.
LONG PRESS TO THE BUTTON AGAIN WILL TURN OFF THE POWER.
WHEN THE MUSIC IS PLAYING, PRESS
BUTTON RETURN BACK TO LAST TRACK OF MUSIC.
7
8
RPT REPEAT PLAY BUTTON, WHEN YOU PRESS SUCH BUTTON ONCE CONTINUALLY WILL FOLLOW
BELOW MODE OF CIRCULATION.
Single music repeat, overall music repeat
cancel repeat play
WHEN THE MUSIC IS PLAYING, PRESS
BUTTON FORWARD TO NEXT TRACK OF MUSIC.
9DEL MUSIC DELETE BUTTON, TO DELETE ANY MUSIC FROM THE MEMORY CARD, WHEN THE MUSIC
IS PLAYING, PRESS DEL BUTTON ONCE THE SCREEN WILL DISPLAY “ DEL FILE ” & FLASHING.
PRESS THE BUTTON AGAIN THE MUSIC WILL BE DELETED & FORWARD TO THE NEXT MUSIC & PLAY
AUTOMATICALLY.
Digital Recorder Player Instruction Manual
US B
DE L REC PLAY RE CRP T
PO W ER SENSOR
22
21
20
19
18
1 2 3 4 6 8 127 9 10
13
14
15
16
17
5 11
14
15
16
17
18
19
20
RECORD INDICATOR LED, WHEN THE MUSIC IS RECORDED THE LED WILL BE LIGHTEN. RECORD
STANDBY THE LED WILL BE FLASHING.
IR RECEIVER SENSOR.
USB DRIVER PORT, SUPPORT UP TO 32G 2.0 VERSION.
SD CARD PORT, SUPPORT UP TO 32G CLASS 10 SPECIFICATION.
OVERALL MUSIC FOLDER NUMBER IN THE MEMORY CARD.
FOLDER NUMBER OF THE ON GOING MUSIC IN THE MEMORY CARD.
OVERALL MUSIC NUMBER CAN BE PLAYED IN THE MEMORY CARD.
21 SERIAL NUMBER OF THE ON GOING MUSIC IN THE MEMORY CARD.
ON GOING MUSIC FILE NAME.
22
BUTTON TO STOP RECORDING.
PRESS REC PLAY BUTTON CAN PLAY THE RECORDED SOURCE IMMEDIATELY. EACH RECORDED
SOURCE WILL BE.
PRESS REC BUTTON, THE DEVICE WILL TRANSFORM INTO RECORD STAND BY MODE & SCREEN
WILL DISPLAY “ ESTABLISHING “, THE RED LED LIGHT BELOW REC BUTTON WILL START FLASHING,
FEW SECOND LATER THE SCREEN WILL DISPLAY “CAN RECORD NOW”, PRESS REC BUTTON AGAIN
AT THIS TIME TO START RECORDING. RECORD COMPLETE PRESS
13
5
6
7
8
EXTERNAL AC POWER INPUT.
FUSE.
RECORD OUTPUT.
AUXILIARY 1~ 4 INPUT,
※THE AUXILIARY INPUT 4TH VOLUME CONTROL IS LOCATED AT REAR PANEL.
※THE REST OF OTHER AUXILIARY VOLUME ARE LOCATED AT FRONT PANEL.
10 100V HIGH VOLTAGE ZONE 1~5 OUTPUT AND ALL ZONE OUTPUT TERMINALS.
9MICROPHONE 1~ 4 INPUT,
※THE MICROPHONE INPUT 4TH VOLUME CONTROL IS LOCATED AT REAR PANEL.
※THE REST OF OTHER MICROPHONE VOLUME ARE LOCATED AT FRONT PANEL.
3
4
70V/100V HIGH VOLTAGE OUTPUT.
PRE-OUTPUT 1 & 2 ( 0dB )