MaxTech XT5888 User manual

Part#MAN074Rev.1.0 M1588L
Features
•0.28 mm Dot Pitch
•1024 x 768, Non-Interlaced
•90 Hz Refresh Rate (VGA/SVGA)
•PowerSavingOperation(VESADPMS)
•Non-Glare Screen
•Full Screen Display
•Low Radiation
XT5888
15 INCH
COLOR MONITOR
USER'S
MANUAL

1
Table of Contents
Section 1 - General Information ............................................................ 2
Section 2 - Installation ........................................................................... 3
Section 3 - Monitor Controls and LEDs................................................. 4
Section 4 - Troubleshooting................................................................... 5
Appendix A - Specifications................................................................... 5
Appendix B - Video Cable Pinout .......................................................... 6
Appendix C - Two Year Warranty .......................................................... 6
Appendix D - Notices ............................................................................. 7
Warning
•Read all these instructions. Save for later use.
•Do not expose this unit to rain or moisture.
•Do not use this unit with an extension cord or any outlet other than a
three prong outlet.
•Do not open the cabinet. There are no user serviceable components
inside. Refer all servicing to a qualified technician.
•Do not cover the vent holes in the case. These are to allow ventilation.
•Do not insert sharp objects into the monitor. They may cause fire
accident or failure.
•Install the equipment near an AC outlet.
•Follow all instructions and warnings on the product.
•Do not place the product on an unstable cart.
•Operate from power source indicated on the label.
•Do not allow anything to rest on the power cord.
•Unplug this product from the wall outlet and refer servicing to qualified
service personnel under the following conditions:
A. When the power cord or plug is damaged or frayed.
B. If liquid has been spilled into the product.
C. If the product has been exposed to rain or water.
D. If the product does not operate normally when the operating
instructions are followed. Adjust only those controls that are
covered by the operating instructions since improper adjustment of
the other controls may result in damage and will often require
extensive work by a qualified technician to restore the product to
normal operation.
E. If the product has been dropped or the cabinet has been damaged.
F. If the product exhibits a distinct change in performance, indicating
a need for service.

2
Section 1 - General Information
Congratulations on purchasing a MaxTech 15-inch Color Monitor. The
monitor has one of the finest CRTs available in the industry, providing a
full range of video display resolutions and complies with the MPR-I
standard to reduce electromagnetic emissions.
The monitor has a 0.28 mm dot pitch display with a 65 MHz video
bandwidth. It supports video resolutions ranging from 640 x 350 to 1024
x 768 (non-interlaced).
The monitor can be used with video cards supporting VGA, SVGA, IBM
8514/A or XGA modes and provides an unlimited palette of colors.
1.1 Precautions When Using the Monitor
When setting up and using your monitor, pay special attention to the
following:
• To eliminate eye fatigue, do not use your monitor against a bright
background or where sunlight or other light sources will shine directly
on the monitor.
• Your monitor should be placed just below eye level for optimum
viewing.
• Allow adequate ventilation around the monitor so that heat from the
monitor can properly dissipate.
• Neitherthemonitoritselfnoranyotherheavyobjectshouldrestonthe
power cord. Damage to a power cord can cause fire or electrical
shock.
• Keep the monitor away from high capacity transformers, electric
motors and other strong magnetic fields.
• Do not use your monitor in a damp, dusty or dirty area.
• Handle the monitor with care when transporting.
• Unplug the monitor during electrical storms.
1.2 Power Saving Modes
The MaxTech monitor supports VESA Display Power Management Sig-
naling (DPMS) SUSPEND and OFF modes. DPMS defines a method for
a computer to signal the monitor to reduce its power consumption when
idle. DPMS features must be supported by both the computer and the
monitor for them to be available. Computer support of DPMS requires the
use of a DPMS compliant video card.
The monitor enters DPMS SUSPEND mode when the computer turns off
the Vertical Synchronization signal. This power-saving mode reduces the
monitor’s power consumption to 30W. While in this mode the Power
IndicatorLEDisamber.Whenthesynchronizationsignal isre-enabledthe
monitor returns to normal operation.
ThemonitorentersDPMSOFFmodewhenthecomputerturnsoffboththe

3
Horizontal and Vertical Synchronization signals. This mode reduces the
monitor’s power consumption to 8W. While in this mode the Power
Indicator LED is amber. When the synchronization signals are re-enabled
the monitor returns to normal operation.
Section 2 - Installation
2.1 Attaching the Base
• Carefully place the monitor on its
side or top.
• Insertthehooksontheswivelbase
into the slots in the bottom of the
monitor. Push down and forward
on the base until it snaps into
place.
• Place the display upright in an
appropriate location.
2.2 Connecting the Cable
•Make sure that power to the monitor and the computer is off.
•Connectthecable fromtheback ofthemonitor to thevideoconnector
on the computer.
COM1 COM2 LPT1 VIDEO
VideoCable
Figure2-2Monitor Connections
Figure2-1 ConnectingtheBase

4
• Attach the power cord to the monitor and plug it into an AC outlet.
• The monitor is now ready for use.
Section 3 - Monitor Controls and LEDs
1. Power Indicator:
LED green: The monitor is in normal operating mode.
LED amber: The monitor is in power saving mode.
LED off: The power switch is off.
2. Power Switch:
Push to turn the monitor on. Push again to turn the monitor off.
3. Brightness Control:
Adjusts the display brightness.
4. Contrast Control:
Adjusts the display contrast.
5. Horizontal-Size
Adjusts the display width.
6. Horizontal-Position
Adjusts the horizontal position.
Figure 3-1 Monitor Controls
10
(on back)
9 8 7 6 5 4 3
1
2

5
7. Vertical-Size
Adjusts the display height.
8. Vertical-Position
Adjusts the vertical position.
9. Pincushion
Adjusts the shape of the left and right sides of the display.
10. Rotation Control (rear of unit)
Adjusts display tilt.
Section 4 - Troubleshooting
No picture, power indicator off
• Check AC cord is plugged into outlet and monitor.
• Turn on the power switch.
No picture, power indicators on.
• Adjust brightness and contrast controls.
No picture, power indicator amber.
• Monitor is in DPMS power saving mode. Press a key or move the
mouse.
• Check that video cable is connected completely.
Image is not centered
• Adjust Vertical Position and Horizontal Position controls.
Appendix A - Specifications
PictureTube Size 15-inchdiagonal
Dotpitch 0.28mm
Surfacetreatment Anti-glare
Bandwidth 65MHz
DataArea 11.125x8.5in.
Displaymode
Mode Resolution V.Frequency H.Frequency
VGA 640x350 70 Hz 31.47KHz
VGA 640x400 70 Hz 31.47KHz
VGA 640x480 60 Hz 31.47KHz
VGA 640x350 84 Hz 37.86KHz
VGA 640x400 84 Hz 37.86KHz
VGA 640x480 72 Hz 37.86KHz
8514A 1024x768 87Hz 35.52KHz
SVGA 800x600 60 Hz 37.88KHz
SVGA 800x600 72 Hz 48.09KHz
UltraVGA 1024x768 60Hz 48.37KHz
UltraVGA 1024x768 70Hz 56.47KHz

6
Synchronization Horizontal: 30-60KHz
Vertical: 50-90Hz
Deflection
Geometricdistortion H<=2.5mm,V<=2.5mm
Linearitydistortion H<=10%,V<=8%
Pincushiondistortion <=2mm
Highvoltageregulation H<=4mm,V<=4mm(0-25FL)
Lowradiation MPR-Ispecification
Frontcontrols Power,Brightness,Contrast,Horizontal-Size,Horizontal-
Position,Vertical-Size,Vertical-Position,Pincushion
RearControl DisplayTilt
Powersaving DisplayPowerManagementSignaling(DPMS)
SUSPENDmode 30W(Max.)
OFFmode 8W (Max.)
Inputvoltage 100-240VAC,50/60Hz
Powerconsumption 90Wmaximum
Operating Temperature 0-40°C
Environment Humidity 20-90%(non-condensing)
Altitude 0-10,000ft.
Connector 15Pin D-Sub
Dimensions 14.63x14.62 x16.21in.
Specificationssubjecttochangewithoutnotice.
Appendix B - Video Cable Pinout
Appendix C - Two Year Warranty
MaxTechwarrantstotheoriginalbuyerofthisproductagainstdefectsinmaterialand
workmanshipfortwoyearsfromthedateofpurchase.
FigureB-1 Pin
Layout and Pin
AssignmentChart
PIN SIGNAL PIN SIGNAL
1Red 9 No Connect
2Green 10 Di
g
ital Ground
3 Blue 11 Monitor Sense 1
(Jumper to Pin 10)
4Monitor Sense 1
(Jumper to Pin 10) 12 No Connect
5Monitor Sense 1
(Jumper to Pin 10) 13 Hor. Synch.
6Red Return 14 Vert. Synch
7Green Return 15 No Connect
8Blue Return
61
5
10
11
15

7
Exceptasspecifiedbelow,thiswarrantycoversalldefectsinmaterialorworkmanship
inthisproduct.Thefollowingarenotcoveredbythewarranty:
1. AnyproductwhichisnotdistributedinNorthAmericabyMaxTechorwhichisnot
purchasedinNorthAmericafromanauthorizedMaxTechDealer.
2. Anyproductonwhichtheserialnumberhasbeendefaced,modifiedorremoved.
3. Damage,deteriorationormalfunctionresultingfrom:
a. Accident,misuse,abuse,neglect,fire,water,lightningorotheractsofnature,
commercialorindustrialuse,unauthorizedproductmodification,orfailureto
followinstructionssuppliedwiththeproduct.
b. RepairorattemptedrepairbyanyonenotauthorizedbyMaxTech.
c. Anyshipmentoftheproduct(claimsmustbepresentedtothecarrier).
d. Removalorinstallationoftheproduct.
e. Anyothercausewhichdoesnotrelatetoaproductdefect.
4. Cartons, carrying cases, batteries, external cabinets, magnetic tapes or any
accessoriesusedinconnectionwiththeproduct.
MaxTechwillpayalllaborandmaterialexpensesforcovereditems,butwewillnotpay
forthefollowing:
1. Removalorinstallationcharges.
2. Costs of initial technical adjustments (set-up), including adjustment of user
controls.
3. Paymentofshippingcharges.
HOW TO OBTAIN WARRANTY SERVICE
If you have problems with your monitor, refer to the troubleshooting section of this
manual.Ifyouareunabletoresolvetheproblem,contactthedealerordistributorfrom
whomtheproductwaspurchased.Adefectivemonitorshouldbereturnedinitsoriginal
packagingtoyourdealerforwarrantyservice.
LIMITATION OF IMPLIED WARRANTIES
Allimpliedwarranties,includingwarrantiesofmerchantabilityandfitnessforaparticular
purpose,arelimitedindurationtothelengthofthiswarranty.
EXCLUSION OF DAMAGES
MaxTech'sliabilityforanydefectiveproductislimitedtotherepairorreplacementofthe
product,atouroption.MaxTechshallnotbeliablefor:
1.Damagetootherpropertycausedbyanydefectsinthisproduct,damagesbased
uponinconvenience,lossofuseoftheproduct,lossoftime,commercialloss;or
2.Anyotherdamages,whetherincidental,consequentialorotherwise.
Somestatesdonotallowlimitationsonhowlonganimpliedwarrantylastsand/ordonot
allowtheexclusionorlimitationofincidentalorconsequentialdamages,sotheabove
limitationsandexclusionsmaynotapplytoyou.
HOW STATE LAW RELATES TO THE WARRANTY
Thiswarrantygivesyouspecificlegalrights,andyoumayalsohaveotherrightswhich
varyfromstatetostate.
Appendix D - Notices
FCC Class B Statement
ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassBdigital

8
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipmentgenerates,usesandcanradiateradiofrequencyenergy,andifnotinstalled
andusedinaccordancewiththeinstructions,maycauseharmfulinterferencetoradio
communications.However,thereisnoguaranteethatinterferencewillnotoccurina
particular installation. If this equipment does cause harmful interference to radio or
televisionreception,whichcanbedeterminedbyturningtheequipmentoffandon,the
user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorientorrelocatethereceivingantenna
• Increasetheseparationbetweentheequipmentandthereceiver
• Connecttheequipmentintoanoutletonacircuitdifferentfromthat towhichthe
receiverisconnected
• Consultthedealeroranexperiencedradio/TVtechnicianforhelp
Notice:Shieldedcables,ifany,mustbeusedinordertocomplywiththeemissionlimits.
AnychangeormodificationnotexpresslyapprovedbytheGranteeoftheequipment
authorizationcouldvoidtheuser’sauthoritytooperatetheequipment.
Canadian DOC Compliance Statement
Thisequipmentdoesnotexceed ClassBlimits forradionoiseemissionsforadigital
apparatus,setoutintheRadioInterferenceRegulationsoftheCanadianDepartment
ofCommunications.Operationinaresidentialareamaycauseunacceptableinterfer-
encetoradioandTVreceptionrequiringtheowneroroperatortotakewhateversteps
necessarytocorrecttheinterference.
CetéquipementnedépassepasleslimitsdeClassBd'émissiondebruitsradioélectriques
pourlesappareilsnumériques,tellesqueprescritesparleRèglementsurlebrouillage
radioélectriqueétabliparleministèredesCommunicationsduCanada.L'exploitation
faite en milieu résidentiel peut entraîner le propriétaire ou l'opérateur à prendre
dispositionsnécessairespourenéliminerlescauses.
Disclaimer, Copyright, And Other Notices
Theinformationcontainedinthismanualhasbeenvalidatedatthetimeofthismanual's
production.The manufacturerreservestherightto makeanychangesandimprove-
ments in the product described in this manual at any time and without notice.
Consequently,themanufacturerassumesnoliabilityfordamagesincurreddirectlyor
indirectlyfromerrors,omissionsordiscrepanciesbetweentheproductandthemanual.
Allregisteredtrademarksarethepropertyoftheirrespectiveowners.
Copyright©1996MaxTech.Allrightsreserved.Noreproductionofthisdocumentinany
formisallowedwithoutwrittenpermissionfromMaxTech.
FirstEdition GZ/DR - Version 1.0

9