Maytag Commercial Washer User manual

W10474266C
W10474280C – SP
TABLE OF CONTENTS
Page
Washer Safety.......................................................................... 2
Tools & Parts............................................................................ 3
Dimensions .............................................................................. 4
Location Requirements........................................................... 5
Drain System............................................................................ 6
Electrical Requirements.......................................................... 7
Installation instructions .......................................................... 8
Connect Drain Hose................................................................ 9
Connect Inlet Hoses.............................................................. 10
Level Washer.......................................................................... 11
Installing Coin Slide and Coin Box....................................... 11
Complete Installation............................................................ 12
Typical Full Load Sizes.......................................................... 12
Washer Maintenance............................................................. 13
If You Need Assistance ......................................................... 14
Alternate Parts....................................................................... 14
Electronic Controls Set-up Instructions.............................. 15
TABLE DES MATIÈRES
Page
Sécurité de la laveuse........................................................... 19
Outillage et pièces................................................................. 20
Dimensions ............................................................................ 21
Exigences d’emplacement ................................................... 22
Système de vidange.............................................................. 23
Spécications électriques .................................................... 24
Instructions d’installation ..................................................... 25
Raccordement du tuyau de vidange.................................... 26
Raccordement des tuyaux d’arrivée d’eau ......................... 27
Établissement de l’aplomb de la laveuse............................ 28
Installation de la glissière et de la boîte à monnaie........... 28
Achever l’installation............................................................. 29
Taille typique des charges complètes ................................. 29
Entretien de la laveuse.......................................................... 30
Si vous avez besoin d’assistance ........................................ 31
Autres pièces ......................................................................... 31
Instructions de paramétrage des commandes
électroniques ......................................................................... 32
INSTALLATION
INSTRUCTIONS
CommerCial Washer
www.maytagcommerciallaundry.com
INSTRUCTIONS
D’INSTALLATION
laveuse CommerCiale

2
WASHER SAFETY

3
Parts Supplied:
Water Inlet Hoses (2) Inlet Hose Washers (4)
TOOLS & PARTS
Tools Needed:
Level Pliers Utility Knife
Adjustable Wrench Flat-Blade Screwdriver
Drain hose with clamp,
U-form, and cable tie
Optional tools:
Flashlight Bucket

4
DIMENSIONS
Front View Side View
271/2"
(699 mm)
35"
(889 mm)
Non-coin-operated
models:
61/4"
(159 mm)
Coin-operated
models:
81/4"
(210 mm)
1"
(25 mm)
27"
(686 mm)
Back View
NOTE: Service panel not included on some models.
Non-coin operated models Coin operated models
411/4"
(1.047 m)
27"
(686 mm)
351/2"
(902 mm)
41/4"
(108 mm)
1"
(25 mm)
61/2"
(165 mm)
36"
(914 mm)
101/2"
(267 mm)
16"
(406 mm)
51/2"
(140 mm)
431/4"
(1.098 m)
27"
(686 mm)
41/4"
(108 mm)
61/2"
(165 mm)
36"
(914 mm)
351/2"
(902 mm)
101/2"
(267 mm)
16"
(406 mm)
51/2"
(140 mm)
1"
(25 mm)

5
Selecting the proper location for your washer improves
performance and minimizes noise and possible washer “walk.”
Your washer can be installed in a basement, laundry room, or
recessed area. See “Drain System.”
Companion appliance location requirements should also be
considered.
IMPORTANT: Do not install or store the washer where it will be
exposed to the weather. Do not store or operate the washer in
temperatures at or below 32°F (0°C). Some water can remain in
the washer and can cause damage in low temperatures. Proper
installation is your responsibility.
You will need:
nA water heater set to 120°F (49°C).
nA grounded electrical outlet located within 4 ft. (1.2 m) of
power cord on back of washer. See “Electrical Requirements.”
nHot and cold water faucets located within 4 ft. (1.2 m) of hot
and cold water ll valves on washer, and water pressure
of 20-100 psi (138-690 kPa). A pressure reduction valve
should be used in the supply line where inlet pressure entering
the building exceeds 100 PSI (690 kPa) to avoid damage to
the washer mixing valve.
nSingle washer installations require 12" (300 mm) minimum
risers to provide an air cushion and avoid noise and damage
to valves.
nA level oor with maximum slope of 1" (25 mm) under entire
washer. Installing on carpet is not recommended.
n Floor must support washer’s total weight (with water and load)
of 315 lbs (143 kgs).
nA oor drain under the bulkhead. Prefabricated bulkheads
with electrical outlets, water inlet lines, and drain facilities
should be used only where local codes permit.
LOCATION REQUIREMENTS
Recessed Area or Closet Installation
This washer may be installed in a recessed area or closet.
The installation dimensions shown are the minimum spaces
allowable. Additional spacing should be considered for ease of
installation and servicing. If closet door is installed, the minimum
air openings in top and bottom of door are required. Louvered
doors with air openings in top and bottom are acceptable.
Companion appliance spacing should be considered.
Minimum installation spacing

6
DRAIN SYSTEM
Drain system can be installed using a oor drain, wall standpipe,
oor standpipe, or laundry tub. Select method you need.
Floor standpipe drain system
Minimum diameter for a standpipe drain: 2" (51 mm). Minimum
carry-away capacity: 10 gal. (38 L) per minute. Top of standpipe
must be at least 39" (990 mm) high; install no higher than
96" (2.44 m) from bottom of washer.
Laundry tub drain system
4.5"
(114 mm)
4.5"
(114 mm)
39"
(990 mm)
39"
(990 mm)
4.5"
(114 mm)
Wall standpipe drain system
See requirements for oor standpipe drain system.
Floor drain system
Floor drain system requires a Siphon Break Kit (Part Number
285834). Minimum siphon break: 28" (710 mm) from bottom
of washer. Additional hoses may be needed.
Minimum capacity: 20 gal. (76 L). The top of the laundry tub
must be at least 39" (990 mm) above oor.

7
ELECTRICAL REQUIREMENTS
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
re, or electrical shock.
WARNING
n
A 120 volt, 60 Hz., AC only, 15- or 20-amp, fused electrical supply
is required. A time-delay fuse or circuit breaker is recommended.
It is recommended that a separate circuit breaker serving only
this appliance be provided.
nThis washer is equipped with a power supply cord having
a 3 prong grounding plug.
nTo minimize possible shock hazard, the cord must be plugged
into a mating, 3 prong, grounding-type outlet, grounded in
accordance with local codes and ordinances. If a mating outlet
is not available, it is the personal responsibility and obligation
of the customer to have the properly grounded outlet installed
by a qualied electrician.
nIf codes permit and a separate ground wire is used, it is
recommended that a qualied electrician determine that
the ground path is adequate.
n Do not ground to a gas pipe.
n Check with a qualied electrician if you are not sure the
washer is properly grounded.
nDo not have a fuse in the neutral or ground circuit.

8
It is necessary to remove all shipping materials for proper
operation and to avoid excessive noise from washer.
1. Move washer to within 4 ft (1.2 m) of its nal location; it must
be in a fully upright position.
NOTE: To avoid oor damage, set washer onto cardboard
before moving it and make sure lid is taped shut.
48"
(1.2 m)
INSTALLATION INSTRUCTIONS
2. To avoid damaging oor, place cardboard supports from
shipping carton on oor behind washer. Tip washer back and
place on cardboard supports. Remove shipping base. Set
washer upright.
IMPORTANT: Removing shipping base is necessary for proper
operation. If your washer includes a sound shield, please refer
to the instructions included with the sound shield to install it
at this time.
NOTE: Keep shipping base in case you need to move washer
later.
3. Remove tape from washer lid, open lid, and remove cardboard
packing tray from tub. Be sure to remove all parts from tray.
NOTE: Keep tray in case you need to move washer later.

9
4.5"
(114 mm)
Drain
hose form
Proper routing of the drain hose avoids damage to your oor
due to water leakage.
Remove drain hose from the washer drum
1. Remove tape from the washer drain port on the back of
the washer.
2. If clamp is not already in place on elbow end of drain hose,
slide it over end as shown.
3. Squeeze clamp with pliers and slide elbow end of drain
hose onto washer drain port and secure with clamp.
4. The washer drain system can be installed using a oor drain,
wall standpipe, oor standpipe, or laundry tub.
CONNECT DRAIN HOSE
5. Place hose into standpipe (shown in picture) or over side
of laundry tub.
IMPORTANT: 4.5" (114 mm) of drain hose should be inside
standpipe; do not force excess hose into standpipe or lay
on bottom of laundry tub. Drain hose form must be used.
6. For oor drain installations, you will need to remove the drain
hose form from the end of the drain hose. You may need
additional parts with separate directions. See “Tools and Parts.”
7. The oor drain system requires a siphon break that may be
purchased separately. The siphon break (Part Number 285834)
must be a minimum of 28" (710 mm) from the bottom of the
washer. Additional hoses might be needed.

10
CONNECT INLET HOSES
Connect Inlet Hoses to Washer
1. Attach cold water hose to cold water inlet valve marked
with a blue ring. Screw coupling by hand until it is snug.
2. Attach hot water hose to hot water inlet valve marked
with a red ring. Screw coupling by hand until it is snug.
3. Use pliers to tighten couplings an additional two-thirds turn.
NOTE: Do not overtighten. Damage to the valve can result.
4. Turn on water faucets to check for leaks. A small amount
of water may enter washer. It will drain later.
NOTE: Replace inlet hoses after 5 years of use to reduce the
risk of hose failure. Record hose installation or replacement
dates on the hoses for future reference.
Periodically inspect and replace hoses if bulges, kinks, cuts,
wear, or leaks are found.
Insert new hose washers (supplied) into each end of the inlet
hoses. Firmly seat the washers in the couplings.
Connect Inlet Hoses to Water Faucets
1. Attach hose to hot water faucet. Screw on coupling until
it is seated on washer. Repeat process for cold water.
2. Use pliers to tighten the couplings an additional
two-thirds turn.
IMPORTANT: Do not overtighten or use tape or sealants on valve
when attaching to faucets or washer. Damage can result.
Clear Water Lines
nRun water through both faucets and inlet hoses, into a laundry
tub, drainpipe, or bucket, to get rid of particles in the water
lines that might clog the inlet valve screens.
n Check the temperature of the water to make sure that the hot
water hose is connected to the hot water faucet and that the
cold water hose is connected to the cold water faucet.
CouplingWasher