MB QUART MBQX-RAD-1 Manual

Operator’s Guide and
Installation Instructions
MBQ X-R AD-1
AM/FM/USB/Bluetooth®
Multimedia Controller and
Vehicle-Specic Housing
for Can-Am X3 Vehicles

2
Congratulations for choosing the MBQX-RAD-1, an AM/FM/WB,
USB and Bluetooth Multimedia Controller by MB Quart. The
unit and housing are engineered to t 2017 and newer Can-Am
Maverick X3 vehicles. For more detailed information about the
product and a video tutorial, please visit MBQuart.com
CAUTION
Always consider consulting a professional audio installation
technician before installing any mobile audio components. Be
careful and take your time. Do not let wires make contact with
metal edges, sources of moisture or hot engine components.
General Information
Powersports and Marine Multimedia Source Unit
AM/FM, Weather Band Radio, USB, Bluetooth®and AUX sources
160 Watts Peak Power with Pre Amplier Line Outputs
Marine Certied to IPX67 for Water and Dust Intrusion
Auxiliary A/V Sources
Quick Connect Bluetooth Audio USB Audio Input w/Charging
Auxiliary RCA Stereo Preamp Input Weather Band Radio
Composite Video Camera Input Composite Video Output
AM / FM / Weather Band Section
USA Frequency: FM87.9 – 107.9MHz / AM530-1710kHz
Europe Frequency: FM87.5 – 108MHz / AM522 – 1620kHz
NOAA NWR Weather Band Frequency: 162.400-162.550MHz
Intermediate AM/FM Frequency: 10.7MHz
Intermediate Frequency Rejection: 50dB
Noise Limit Sensitivity: >5uV
USB / AUX / Bluetooth Audio Section
RCA S/N: >81dB Powered Outputs S/N: >74dB
USB A/D Conversion: 16bit Frequency Response: 20Hz – 20KHz
Audio Section & Other Features
Power Output: 4 x 40 Watts Max (160 Watts Peak Power)
Load Impedance: 4 - 8 Ohms / Channel
Preamp Output Voltage: 4 volts
Dual Zone Capability between Preamp Outputs and Built-in Power
Independent Subwoofer Level Control with Selectable Low Pass Filter
8-Band Graphic EQ (62, 125, 250, 500, 1K, 4K, 10K and 16K)
Installation Specications (Source Unit Only)
4” / 100mm - Total Mounting Depth Required Inside Housing
3” / 76.2mm - Housing Cut Out Diameter

3
Wiring and Connections
(M) Yellow
(L) White/Black
Water Tight Plug Face Shown (Wires to Connect Exit Rear)
(K) White
(J) Red
(H) Purple/Black
(G) Purple
(F) Gray
(E) Gray/Black
(D) Green/Black
(C) Green
(B) Blue
(A) Black
Yellow (+12v Constant)
Red (+12v Accessory)
Water
Tight Plug
USB Connector
Orange (Illumination)
Purple/White (Reverse)
AM/FM Antenna
AUX Input
SUB Outputs
FRONT Preamp
Outputs*
REAR
Preamp Outputs*
Camera Input
CVBS Video Output
(Mirrors Unit’s Screen)
Black (Chassis Ground)
Blue(Amp Turn-On)
*Works with
ZONE Control
Note: See wiring chart on next page for connection tips, wire
colors and functions. Also note preamp level output connections
if using external ampliers and ZONE control capability.
See page 19 for Video Output details

4
Wiring and Connections
Wire Color Location Function
Black Plug Pin A Negative Chassis Ground (-)
Blue Plug Pin B Amp Turn-On (+12v Output)
Green Plug Pin C Left Rear Speaker (+)
Green/Black Plug Pin D Left Rear Speaker (-)
Gray/Black Plug Pin E Right Front Speaker (+)
Gray Plug Pin F Right Front Speaker (-)
Purple Plug Pin G Right Rear Speaker (+)
Purple/Black Plug Pin H Right Rear Speaker (-)
Red Plug Pin J +12 volt Accessory
White Plug Pin K Left Front Speaker (+)
White/Black Plug Pin L Left Front Speaker (-)
Yellow Plug Pin M +12 volt Constant (>10a)
Purple/White Harness Reverse Camera +12v Input
Orange Harness +12 volt Illumination
Preamp Level Audio Connections
● Front and rear RCA preamp outputs are labeled as such. These are
intended to be connected to external ampliers, not included.
● Subwoofer RCA outputs (green RCAs) are mono and paralleled.
They are identical subwoofer audio signals. Their frequency range is
controlled by the low pass crossover and the subwoofer level control.
Both are found in SETTINGS. See Page 18. We recommend starting
with 100Hz for the low pass crossover point.
● The unit offers a zone control feature to balance sound levels
between different zones. The front and/or rear RCA outputs (using
external ampliers) are one zone. The source unit's built-in power is
the other zone. An example is a boat having separate volume control of
amplied wakeboard tower speakers versus cabin speakers positioned
closer to listeners using the unit's built-in power. Zone level control is
found in SETTINGS. See page 18. Subwoofer RCA outputs or speaker-
level outputs are unaffected by the zone level control. All work with the
main volume.
● MB Quart recommends wire-to-wire connections such as power,
ground and speaker wiring are soldered and protected with either heat
shrink tubing or high quality electrical tape.
● The main (yellow) power wire should be connected to a source with at
least 10 amps of additional current capability to support the unit.

5
Can-Am X3 Source Unit Mounting Instructions
3
4
3) Take note of the four
(4) holes for mounting of
the source unit’s housing
as shown. These must be
carefully drilled. Two (2)
in front and two (2) at the
back.
4) Set source unit housing
in place in center dash area
to locate four (4) mount-
ing holes required for nal
mounting. Using a perma-
nent marker or awl, locate
and mark dimples for veri-
cation of where you'll drill.
Remove housing and set
aside when completed.
Mark Holes
Back
Front
1
1) Remove top center plas-
tic cover above dash pock-
et. Push up on the front
pocket edge above lighter
socket, then pull toward
you. Remove lighter socket
to facilitate wiring path or
drill a 1" hole on the side of
the pocket near the lighter
socket for wire access.
2
2) Connect and route all wir-
ing (as described on page
3 and 4) to source unit area
as shown. Connect source
unit wiring pigtail using the
wiring diagram. Remember
to include any RCA audio
or USB cables if the apply
in your system. Do not yet
connect to source unit.
Route and
Connect
Wiring Here

6
Can-Am X3 Source Unit Mounting Instructions
7
8
7) Connect the electrical
plug and, if used, RCA
audio and USB cables. Test
source unit functionality and
sound before nal mounting
and installation. See Trou-
bleshooting section on page
22 if needed.
8) Place the source unit in
the na installation location
with wiring neatly secured
and zip tied in place. Attach
the four included screws
through the housing’s
mounting holes drilled out
earlier. Two T-25 32mm
screws (front) and two T-25
24mm screws (back).
5
5) Using battery-powered
cordless drill with a 9/64”
drill bit, drill two (2) mount-
ing holes in the dimpled
areas as indicated. As the
material is plastic, there is
very little pressure need-
ed..
6
6) Drill the remaining two (2)
mounting holes at the back
of the housing as indicated.
Again, as the material is
plastic very little pressure is
needed.

7
1/ 2/INT 3/RPT 4/RDM
Source
POWER/Selector and Volume Knob
● Press the POWER/Selector Knob to power on the unit.
● Rotate the POWER/Selector Knob to view sources when source
selection menu wheel is displayed. To select a source, press and
release the POWER/Selector Knob.
● Rotate the POWER/Selector and Volume Knob to increase or
decrease sound levels once a source is selected.
● Press and hold the POWER/Selector Knob for 5 seconds to power
the unit off.
SOURCE Button
● Press the SOURCE button to display the source selection menu
wheel. See next page for details. Also functions as the “back” button
in a SETTINGS menu (such as EQ, Audio, Zone Volume, Clock
Adjust, Backlight, etc.)
1/ Button
● Preset 1 for AM/FM, pairing on Bluetooth source.
2/INT Button
● Preset 2 for AM/FM. No other function.
3/RPT Button
● Preset 3 for AM/FM. Repeat play (1 or all) on USB source.
4/RDM Button
● Preset 4 for AM/FM. Random play (Shufe) on USB source
Scan Down for AM/FM or Track Back for USB/Bluetooth source.
Mute for AM/FM and AUX or Play/Pause for USB/Bluetooth source.
Scan Up for AM/FM or Track Up for USB/Bluetooth source.
1
34 5
2
Front Panel Controls
1
6
3
4
5
6
7
9
8
987
2

8
Source Selection
AM Radio
FM Radio
Camera Input
Settings
USB
Aux Input
Bluetooth
Weather
1/ 2/INT 3/RPT 4/RDM
Source
1/ 2/INT 3/RPT 4/RDM
Source
Press SOURCE Button to
display source selection
menu.
Step 1
Rotate Selector Knob
to choose a source
or settings.
Press Selector Knob (once) to
complete source selection menu.
Step 3
Step 2
1/ 2/INT 3/RPT 4/RDM
Source
Source
Note: On USB source, the unit “auto selects” USB input whenever a device
is plugged in. All other sources must be selected by the user. When select-
ing Bluetooth, a device must be rst paired to playback audio.

9
AM/FM Conguration
Several congurable AM/FM radio parameters are available.
● Select between AM or FM on the Source Menu wheel. Each has its
own menu.
● Once the chosen source is selected, press and hold the SOURCE
button for 2 seconds. The AM or FM menu will appear (whichever
source is selected).
● Use the source menu selector knob to scroll to the chosen
parameter. Press the center of the knob to either adjust the parameter
directly, or enter the sub-menu and adjust by scrolling and pressing
the center of the knob again.
● A complete list of each paramater and its variables is listed on the
following page.
● Use the SOURCE button to go back to the previous screen.
● Continue using the SOURCE button to exit AM or FM setup.
1/ 2/INT 3/RPT 4/RDM
Source
After selecting AM or FM source, press
and hold SOURCE button for 2 seconds
to enter the AM or FM Settings menu.
Use the Menu Selector Knob to navigate
the menu items.
Press and Hold
(2 seconds).

10
AM/FM Conguration
Settings Choices for AM
● PRESETS - This function shows stored AM presets 1-6 on AM1 or
AM2. Only presets 1-4 have front panel quick access buttons without
using this menu.
● SAVE PRESETS - This function stores AM presets in spaces 1-6.
Only presets 1-4 have front panel quick access buttons.
● RADIO REGION - This function specices the region: EUROPE,
USA1, USA 2, JAPAN or RUSSIA. This function also controls FM
RADIO REGION setting simultaneously and will reset the clock. USA1
is recommended for USA.
● LOCAL - This function lters out weaker signals when ON to limit only
strong stations in seek feature. Choose OFF when signals have with
adequate reception. Also controls FM LOCAL setting.
● AM BAND - This function selects AM1 or AM2 bands. Choose and
store and recall AM presets. 6 on AM1, 6 on AM2.
● AUTO STORE - Automatically searches and stores presets in
memory.
● STEREO - Choose STEREO or MONO. Recommended to set to
MONO for AM as AM radio signal is broadcast in mono.
Settings Choices for FM
● PRESETS - This function shows stored FM presets 1-6 on FM1, FM2
or FM3. Only presets 1-4 have front panel quick access buttons without
using this menu.
● SAVE PRESETS - This function stores FM presets in spaces 1-6.
Only presets 1-4 have front panel quick access buttons.
● RADIO REGION - This function specices the region: EUROPE,
USA1, USA 2, JAPAN or RUSSIA. This function also controls AM
RADIO REGION setting simultaneously and will reset the clock. USA1
is recommended for USA.
● LOCAL - This function lters out weaker signals when ON to limit only
strong stations in seek feature. Also controls AM LOCAL setting.
● FM BAND - This function selects between FM1, FM2 or FM3 bands.
Choose and store and recall FM presets. 6 each on FM1, FM2 & FM3.
● AUTO STORE - Automatically searches and stores presets in
memory.
● STEREO - Choose STEREO or MONO. Recommended to set to
STEREO for FM as FM radio signal is broadcast in stereo.
.

11
AM/FM and Weather Band Operation
Once setup is complete, select between AM or FM icons on the Source
Menu wheel or simply press the SOURCE button to back up to the
source screen showing the current AM or FM frequency.
● Press the ▌ ◄◄ or ►►
▌
buttons less than 1 second to manually seek
radio stations one frequency at a time.
● Press the ▌ ◄◄ or ►►
▌
buttons more than 1 second to automatically
seek the next / previous radio stations with strong reception.
● Press and hold buttons 1-4 below the screen to store a preset. Four
AM and four FM preset locations are available on the front panel.
Note: Two more AM and FM presets (5 and 6) are located in the AM and FM setup menus, but
note that 5 and 6 are only accessible through the menu, not the front panel buttons.
● Press the center ►▌▐ button to mute the AM or FM source. Press
►▌▐ again to unmute or simply rotate the volume control knob.
Weather Band Operation
Select the Weather icon on the Source Menu wheel.
● Press the ▌ ◄◄ or ►►
▌
buttons less than 1 second to manually seek
weather band stations one frequency step at a time.
● Press the ▌ ◄◄ or ►►
▌
buttons more than 1 second to automatically
seek the next / previous weather band stations with strong reception.
● Press the center ►▌▐ button to mute the weather band source.
Press ►▌▐ again to unmute or simply rotate the volume control knob.
● Press and hold buttons 1-4 below the screen to store a preset.
Four weather band preset locations are available.
FM Screen Example AM Screen Example
Weather Band Screen Example

12
Bluetooth Pairing
The multimedia controller supports Bluetooth A2DP for wireless music
streaming from a mobile device, such as a smartphone or streaming
music source component. The unit does not support the HF (Hands-
Free) or PBAP (Phone Book Access for Contacts) proles. No calling
features are available, only Bluetooth music streaming.
Pairing a Bluetooth device:
● Ensure the multimedia controller is on and Bluetooth is the selected
source. The screen will show "BT Disconnected!"
● Ensure the Bluetooth functionality on the mobile device is enabled
and supports A2DP audio streaming.
● Scan for "MB QUART" in the Bluetooth list on the mobile device.
● Select “MB QUART” and the connection will then be made
automatically.
● A "BLUETOOTH Loading" screen will appear briey as the mobile
device's song info and album art are transfered to the multimedia
source unit.
See next page if a pin code is required to pair.
BT Disconnected Screen
BT Connected Screen
Included in Bluetooth Play Screen:
Album Art (or Music Note Icon)
Song Title and Artist Info
Time Elapsed in Song Play
Play or Pause Status

13
Bluetooth Pairing & Operation
If a PIN Code is Required:
● Some Bluetooth devices require inputting a pass code for
connection. Please input code “0000” and the connection will be made
automatically.
Automatically Connecting:
● Once the multimedia controller has made a connection with the
Bluetooth mobile device for the rst time, the unit can then connect to
the Bluetooth mobile device automatically within a valid range.
Manually Disconnecting:
● To disconnect temporarily, for example to take a phone call,
press and hold the 1/ button for 3 seconds and the mobile device
will disconnect. If no phone call is in progress, it will automatically
reconnect to the unit in about 15 seconds.
● To disconnect and allow another user to connect, use the mobile
device to forget the "MB QUART" connection entirely.
Once a Bluetooth device is paired and recognized:
● Be sure the multimedia controller has the Bluetooth source selected.
The multimedia controller should automatically begin playing where
the mobile device last left off of the music player's song or playlist.
● If the unit does not automatically begin playing, press the center ►▌▐
button to play the Bluetooth source. The play (►) symbol will display
when music is playing.The time elapsed in the song play is also
displayed on the screen.
● Press ►▌▐ again to mute and pause the song. The pause (▌▐ )
symbol will display when music is paused.
● Press ►▌▐ again to resume playback or simply rotate the volume
control knob.
● Press the ▌ ◄◄ or ►►
▌
buttons more than 1 second to manually fast
forward or rewind within a song. Press the same button again to stop
the fast forward or rewind function.
● Press the ▌ ◄◄ or ►►
▌
buttons less than 1 second to automatically
fast forward or rewind the next / previous song.
Note: Functions such as "Repeat" and "Random Play" (a.k.a "Shufe") must be controlled
at the mobile device directly.
See the USB Input section for smartphones connected via USB and
the capability for Repeat and Random (Shufe) functionality.

14
USB Input
The multimedia controller supports MP3, WMA, and WAV audio les
with a USB thumb drive connected. Additionally, M4A or Apple Lossless
le types are supported if the user connects an iPhone®using iTunes
as the music player.
Most smartphones with a USB-based charging connector and
USB thumb drives easily connect to the multimedia controller.
Many smartphones include album art through the phone's music
player. Some USB thumb drive les may not include album art,
only song information.
To begin, connect a USB device and the unit reads the music les
automatically.
● A "USB Loading" screen appears as the device's song info and album
art (if present) transfer to the unit. Smartphones take a few seconds
longer than a USB thumb drive.
● If the unit does not automatically begin playing, press the center ►▌▐
button to play the USB source. Press ►▌▐ again to mute and pause the
song. Press ►▌▐ again to resume playback or simply rotate the volume
control knob.
● Press the ▌ ◄◄ or ►►
▌
buttons more than 1 second to manually fast
forward or rewind within a song. Press the same button again to stop
the fast forward or rewind function.
● Press the ▌ ◄◄ or ►►
▌
buttons less than 1 second to automatically fast
forward or rewind the next / previous song.
Read about Repeat (RPT) and Random (RDM) modes and controls on
the following page. Smartphones behave differently than USB drives.
USB Thumb Drive Screen
USB Thumb Drive Screen:
Album Art (or Music Note Icon)
Song Title and Artist Info
Time Elapsed in Song Play
Play or Pause Status
Status of RPT (even when OFF)
Status of RDM (only when ON)
USB Smartphone Screen
USB Smartphone Screen:
Album Art (or Music Note Icon)
Song Title and Artist Info
Time Elapsed in Song Play
Play or Pause Status
Status of RPT & RDM (only when ON)

15
USB RPT and RDM Functionality
The multimedia controller has two modes of making a USB-connected
music library more interesting with Repeat (RPT) and Random (RDM)
functions. Random play is also called "Shufe" on some mobile devices.
USB Thumb Drive RPT and RDM
With a thumb drive connected to the USB input, users
see an icon on the right side of the screen (centered)
that indicates the status of the RPT mode. The default
status is off. RDM (Shufe) default status is off and no
icon shows until it is engaged.
● The RPT sequence of button presses is as follows:
● The RDM (Shufe) sequence of button presses is as follows:
USB Smartphone RPT and RDM
With a smartphone connected to the USB input, users see no icons.
When a function is active, the screen displays a text message of
the mode above 3/RPT button. The default status of RPT and RDM
(Shufe) are both off.
● The RPT sequence of button presses is as follows:
● The RDM (Shufe) sequence of button presses is as follows:
Repeat OFF
Repeat OFF Repeat ONE Repeat ALL Repeat OFF
Shuffle OFF Shuffle OFF
Shuffle ON
Repeat OFF
Repeat ONE Repeat ALL Repeat OFF
rept_1 rept_all rept_off
shuf_onShuffle OFF
Shuffle OFFShuffle ON
shuf_off

16
Auxiliary (AUX) Input and Camera
The multimedia controller has right and left preamp level RCA
connections for the Auxiliary Input. If a portable device with a
headphone jack is used, a 3.5mm (male) to RCA (male) adapter cable
is required and not included.
Select the AUX icon on the Source Menu wheel.
● Press play on the auxiliary device and turn up its volume. Volume is
controlled from the Selector/Volume Knob on the unit.
● Press the center ►▌▐ to mute. This only mutes the input. It does not
pause the song. Press ►▌▐ again to unmute or simply rotate the volume
control knob.
Camera Operation
● Connect the yellow RCA "Camera Input" to the installed camera's
composite video output.
● Connect the camera's ground wire to a known good source of chassis
ground. If in doubt, connect to the same ground point where the unit's
black wire is grounded.
● Connect a +12 volt trigger, typically a reverse gear signal, to the unit's
purple/white wire. This automatically triggers the camera screen when
active. It should supply +12 volts to trigger.
● User can also manually select the "Camera" source from the menu.
1/ 2/INT 3/RPT 4/RDM
Source After selecting AUX in the source
menu, begin paying the music on the
auxiliary device. Turn its volume up.
Main volume can then be controlled via
the unit along with muting audio.
Select the AUX
icon in the menu.
1/ 2/INT 3/RPT 4/RDM
Source The unit displays a clear picture of
whatever view the camera views.
This could be used for a front thermal
imaging UTV camera or boat docking
camera depending on the application.
Manually select the Camera icon or
trigger automatically w/reverse input.

17
SETTINGS Menu
To access SETTINGS, press Selector/Volume knob in any source.
The "SETTINGS" menu appears immediately. Alternatively, select
"SOURCE" and navigate to the SETTINGS icon ("Gear" icon), then
press the Selector/Volume knob to access the menu.
● Use the Selector/Volume knob to navigate the menu items. When the
gray highlighted bar is on the chosen parameter, press the Selector/
Volume knob to go into that menu (or sub-menu). This is similar to
an "Enter" command. Use the Selector/Volume knob to navigate
parameters within the menu. Once the parameter is set, use the
SOURCE button to go back to the previous screen.
Equalization (EQ)
● Use the Selector/Volume knob to
select the 8-band graphic EQ.
● Navigate each EQ band by turning
the knob and select the band by
pushing the knob.
● Adjust each band as desired, then
push the knob again to move to
another band.
● Use the SOURCE button to close the EQ screen when complete and
return to the main menu.
Clock Mode
● Access the clock mode menu to
adjust 12 hour (USA) and 24 hour
(Europe/World) clock.
● Verify preferred setting with the
check marked choice.
● Use the SOURCE button to close
the clock mode screen when complete and return to the main menu.
1/ 2/INT 3/RPT 4/RDM
Source Use the Selector/Volume knob to navi-
gate the main menu by turning to scroll
and pressing to enter a specic feature
or sub-menu.
Press the Selector/Volume knob in
any source, or select the "Gear" icon.
8 EQ Bands: 62Hz, 125Hz, 250Hz,
500Hz, 1KHz, 4KHz, 10KHz and 16KHz

18
SETTINGS Menu (Continued)
Clock Adjust
● Access the clock adjust mode menu
to change the time displayed on the
unit's main screen.
● Navigate each time parameter (hour,
then minute) by turning the knob and
select by pushing the knob.
● Adjust the hour parameter as desired,
then push the knob again to move to minutes.
● AM or PM settings are automatically determined by the clock mode
settings (12 or 24 hour format).
● Use the SOURCE button to close the clock adjust screen when
complete and return to the main menu.
Backlight
● Access the backlight menu to adjust
the brightness of the screen lighting.
● Verify preferred setting with the
check marked choice.
● Use the SOURCE button to close
the backlight screen when complete
and return to the main menu.
Version
● This menu reports the software version in the unit. No settings or
changes are available to the user.
AUDIO Settings Sub-Menu
Access the "Audio" menu and the following adjustments are available:
SUB Frequency
● Adjust the low pass crossover for the SUB preamp (green) RCA
outputs. The choices are 80Hz, 100Hz and 120Hz.
SUB Level
● Adjust the relative volume level for the SUB preamp (green) RCA
outputs in a range of 0 (fully attenuated) to 40 (fully open).
ZONE Level
● Adjust the relative volume level for the front/rear preamp RCA outputs
in a range of 0 (fully attenuated) to 40 (fully open). The unit's built-in
power and SUB levels are unaffected by this adjustment. Only the front/
rear preamp outputs are controlled by the zone volume. See page 20-
21 for example system diagrams utilizing zone control.
Clock Adjust Screen
Backlight Adjust Screen

19
BASS Level
● Adjust the bass from -7 to +7. Default setting is “0.” Center frequency
is 100Hz.
TREBLE Level
● Adjust the treble range from -7 to +7. Default setting is “0.” Center
frequency is 10KHz.
BALANCE Control
● Adjust the balance between the left and right speakers using the grid
on the screen and the Selector/Volume knob to move the dot. Equal
balance (center dot) is the default setting.
● Use the SOURCE button to close the balance screen when
complete and return to the main menu.
FADER Control
● Adjust the fader between the front and rear speakers using the grid
on the screen and the Selector/Volume knob to move the dot. Equal
fader position between front/rear (center dot) is the default setting.
● Use the SOURCE button to close the fader screen when complete
and return to the main menu.
Factory Reset
● This setting resets the unit to its factory defaults. Be cautious
when entering this menu if you don't want to manually reset all
your preferences such as radio presets, EQ, sub level/crossover,
backlighting, etc.
Video Output Feature
● The multimedia controller features a composite video output that
mirrors the same information on the unit's screen. This is a useful
feature to provide a secondary screen for passengers or in other
zones within a larger space, such as a boat or RV.
● Simply connect the unit's
"CVBS-OUT" to the composite
video input of a secondary
screen.
Although the balance and fader adjust-
ments are two separate screens, for
purposes of easy understanding they are
shown here in the same screen. Left and
right of the grid represent the balance.
Top (front) and bottom (rear) of the grid
represent the fader.
Camera Input
CVBS-OUT
Video Output
Connect to
2nd Screen

20
Audio System Design Ideas
Front and Rear
Built-in Power
Front Speakers
4-Speaker System using Built-in Power
Multimedia Controller Rear Speakers
4 Channel Amp
Front and Rear RCAs
Front Speakers
Amplified System
with Subwoofers
Multimedia Controller
Rear Speakers
Subwoofer Amp
SUB (Green) RCAs
Subwoofers