MB QUART Hifonics TPS-BT1 Instruction Manual

Multi-Function Joystick Operation
CAUTION
Always consider consulting a professional audio installer
before installing any audio components. Be careful and take
your time. Do not let wires make contact with metal edges or
hot engine components.
Congratulations on your choice of a Hifonics Bluetooth
controller. This “Quick Start” Installation guide is meant to
help you complete a basic installation. For more detailed
information, visit our website at Hifonics.com and go to the
TEQ Support section or the Frequently asked questions.
MOUNTING
The controller is designed to mount in any convenient location where
drilling a 1.1inch (28mm) hole will not obstruct operation of the unit.
The unit itself requires a 1.1 inch (28mm) round opening with at least
2.5 (64mm) inches of clearance behind the mounting surface. Before
drilling any holes make sure there are no obstructions behind the
mounting surface.
Do not attempt to remove the unit from the switch housing. The
housing is an integral part of the unit.
Keep enough space around the controller
if possible to accommodate the operator’s
ngers.
RUBBER GASKET
Make sure the included rubber gasket
remains in place during installation. This
gasket aides in the unit remaining water
resistant.
AUX INPUT – 3.5MM JACK
The 3.5mm input jack is located on the
bottom of the unit. Remember to re-insert
the water resistant rubber plug when not
using the input. The control unit should always be mounted with the
3.5mm jack on the bottom.
The multi-function joystick has multiple operations for various
features. Take a minute to familiarize yourself with all of the following
to better and more quickly navigate your new Bluetooth controller.
VOLUME
Slowly turn the controller clockwise to increase volume and counter
clockwise to decrease volume. Turning the dial quickly does not
increase the speed of volume increase or decrease. Under AUX
mode the volume will be controlled by your device.
POWER ON/OFF
A. Press and hold control volume for 3 seconds to power
the unit on/off
3.5MM SIGNAL INPUT
A. The controller will automatically switch from Bluetooth
to the AUX input by plugging you device into the 3.5mm
input.
BLUETOOTH CONTROL
RIGHT/DOWN TOGGLE
A. Toggle right or down to advance to the next track
LEFT/UP TOGGLE
A. Toggle left or down to back up to previous track
Controller Mounting
Wiring
Rubber Gasket
3.5mm Plug
Fuse
Red Wire - 12v Power
Black Wire - Ground
Orange Wire - Accessory
Blue Wire - Remote Output
RCA Cables - Signal Output
The wiring and connections should be secure and away from any
moving parts or extremely hot surfaces.
The RCA signal output can be connected directly to an amplier or
to the auxiliary input of an audio head unit.
The blue remote wire provides a +12V output to turn on an
amplier.

Quick Start
Installation Guide
WARRANTY
Maxxsonics USA Inc. warrants this product, to the original consumer purchaser, to be free from
defects in material and workmanship for a period of one (1) year from the date of purchase.
Maxxsonics USA Inc. will, at it’s discretion, repair or replace defective products during the warranty
period. Components that prove to be defective in materials and workmanship under proper installation
and use must be returned to the original authorized Maxxsonics USA Inc. retailer from where it was
purchased. A photocopy of the original receipt must accompany the product being returned. The
costs associated with removal, re-installation and freight are not the responsibility of Maxxsonics
USA Inc. This warranty is limited to defective parts and specically excludes any incidental or
consequential damages connected therewith. To view the full warranty, please visit the website.
Hifonics products are designed and engineered in the USA by
www.maxxsonics.com
HF TPS=BT1 QSG 01 - rev1
Bluetooth Device Pairing
The pairing process can vary based on your particular device.
Refer to the operating instructions of your device. Below is the
general process to connect the controller.
The Bluetooth Controller will ash slowly when “searching” for the
last paired device.
If no device is located, it will ash quickly indicating it is ready to
pair to a new device. On your Bluetooth enabled device, search for
Hifonics under Bluetooth settings.
Select Hifonics; wait for the device to indicate “connected”. The
status indicator will change to solid red. Music will now play through
the system.
TPS-BT1
Bluetooth®Controller