mbp TEL 30BS Datasheet

This instruction manual contains IMPORTANT
WARNINGSANDINSTRUCTIONTHATMUSTBEREAD
BEFORE OPERATINGTHEPUMP
INSTRUCTIONS AND PARTS LIST
SPRAY EQUIPMENT

MBPS.L. C/.Anboto,17 Poligono ANSOLETA Phone:[phone] Fax. [phone]
01006VITORIA(Alava) / SPAIN P.O.BOX 3144
HYDRAULIC
RATIO 30:1
MODELS TEL 30BS TEL 30CS
INOX

WARNING
ATTENTION!! Read and understand all instructions carefully
before operating equipment.
INJECTION HAZARD
Thisequipmentgeneratesveryhighfluidpressure.Spray
from the gun, leaks or ruptured components can inject fluid
through your skin and into your body and cause extremely
seriousbodilyinjury.
The spray gun should never be handled carelessly, nor
spray directed toward any part of the body. Keeps your hands
and fingers away from spray gun nozzle.
Be sure equipment safelydevices are operating properly
before each use.
Ifanyfluidappearstopenetrateyourskin,getemergency
medical care at once. Do not treat as a simple cut. Tell the
doctor exactly what fluid was injected.
FIRE HAZARD
Static electricity is created by the high velocity flow of
fluid through the pump and hose. If every part of spray
equipment is not properly grounded, sparking immediately.
Check the entire system for positive grounding.
GROUNDING
Before starting to work the pump must be connected to
ground:
INDEX:
WARNINGS ............................................................
TYPICAL INSTALLATION ....................................
PRESSURE RELIEF PROCEDURE ........................
HOSE SAFETY .....................................................
SPRAY GUN & OPERATING INSTRUCTIONS .......
MAINTENANCE (CLEANINGAND FLUSHING) .....
SPRAY TIPS ......................................................
PARTS DRAWING AND LIST ....................
TROUBLESHOOTING GUIDE ..........................
TECHNICAL DATA .............................................
STANDARD SPRAY TIPS ...................................
WARRANTY ......................................................
2
3
3
3
3
3
4
4, 5 & 6
7
7
7
8
2
The pump must be connected to ground with a
ground wire which is supplied with the pump
(4 mm2of section and a clamp). See connection
on page 6.
SPRAY GUN: Obtain grounding through
connectiontoaproperlygroundedfluidhoseand
pump.
OBJECT BEING SPRAYED: Use ground wire
and clamp.
AIR COMPRESOR: Follow air compressor
manufacturer’s recommendations.
Use ONLY METAL PAILS, which are
conductive. Do not place the pail on a
non-conductive surface, such as paper or
cardboard, which interrupts the grounding
continuity.
1.-
2.-
3.-
4.-
5.-

PRESSURERELIEFPROCEDURE
HOSESAFETY
Tighten all fluid connections securely before each use.
Never use a damaged hose. Before each use, check entire
hose for cuts, leaks, abrasions, bulding cover, or damage or
movement of the hose couplings. If any of these conditions
exist, replace the hose inmediately.
SPRAYGUN
It is recommended strain the fluid you are spaying if it
contains particles which could clog the spray tip.
CLEANING THE SPRAY TIP
Clean off the front of the tip frequently during the day’s
operation and at the end of the work day. Always follow the
PressureRelief Procedureonpage3.Thenuseasolventsoaked
brushtocleanthespraytipandtokeepfluidbuildupfromdrying
and clogging the spray tip.
If the spray tip clogs while spraying, release the spray
gun trigger, engage the trigger safety, shut off the pump, and
follow the Pressure Relief Procedure.
Remove the spray tip and blow out the obstructions with air
from the front of the spray tip.
Normal daily flushing of your spray system and gun
flushes away most buildup on the filter. However, you should
remove the filter frequently and clean it.
FLUSHING THE GUN
Relieve pressure, remove the spray tip, and then flush
the gun and spray system with a compatible solvent. Always
flush the gun before the fluid being sprayed can dry in it.
Engage the gun safety latch.
Shut off the air to the pump.
Close the air inlet valve.
Disengage the gun safety latch.
Hold a metal part of the gun firmily to the
side of a grounded metal pail, and trigger
the gun safety latch.
Engage the gun safety latch.
Open the drain valve, having a grounded
metal container ready to catch the drainage.
Leave the drain valve open until you are
ready to spray again.
OPERATINGINSTRUCTIONS
Followallinstructionsabove,besurethatfittingsatpump
outlet and at gun are tight. Use two wrench to tighten the main
fitting. Do not install the spray tip at this time.
Fillthepackingnutwithoil to help prolongthepacking
life.
Put the suction tube into the paint container. Flush the
pump with a compatible solvent before using it.
Open the air inlet valve. Disengage the gun safety and
trigger the spray gun into a grounded metal pail, and slowly
open the air supply valve until the pump stars (about 3 or 4
bar). The lines are purged when the fluid emitted from the gun
is flowing in a steady stream. Engage the gun safety, shut off
the air inlet valve then install the spray tip in the gun.
Open the air inlet valve. When the pump and the lines
are primed, and adequate air pressure and volume are supplied,
the pump will start and stop as the spray gun is triggered and
released.
Disengage the gun safety and you are now ready to
spray!!
1.-
2.-
3.-
4.-
5.-
6.-
7.-
8.-
TYPICAL INSTALLATION
3

9
10
MBP
5
7
11 8
24
TEL
30
12 6
3
1
MAINTENANCE (CLEANING AND
FLUSHING)
It is recommended that at the end of each day, paint
should be flushed from unit with compatible solvent then
reflushed with mineralspirits.
1.-
2.-
3.-
4.-
5.-
Engage the gun safety and follow the Pressure
Relief Procedure.
Remove the spray tip and clean with a compatible
solvent and soft brush.
Disengage the gun safety and follow the pressure
relief procedure.Liftsuctiontubeabovepaintlevel
until tube is empty.
Introducingthesuctiontubeinapailwithcompatible
solvent. Disengage gun safety and trigger gun into
the pail until it runs clear. Close the air inlet valve.
Open the fluid drain valve. Remove the fluid filter
and the gun filter and clean them with solvent.
Flush the sprayer at the end of each work day and
fill it with solvent to help prevent pump corrosion.
4
SPRAYTIPS
When a tip is the wrong size, or becomes the wrong size
through wear, the spray pattern worsens, coverage decreases,
you have less control over the desired rate of coverage, and it
takes longer to finish the job. In the worst case, the pump
supplying the tip can be damaged. Because most architectural
coatingareabrasive,tipwearcanhappendquitequickly.Notice
as wear increases the orifice size, it decreases the fan width
which greatly affects coverage rates.
If tip shows excessive wear, replace it to maximize
productivityand save paint.
PARTSLIST
1.-
2.-
3.-
4.-
5.-
6.-
7.-
8.-
9.-
10.-
11.-
12.-
AIRMOTOR
DISPLACEMENTPUMP
AIRLINEFILTERANDAIRREGULATOR
FLUIDSUCCIONLINE
FLUIDDRAINVALVE
AIRINLETVALVE
FLUIDFILTER
PACKINGNUT
FLUIDHOSE
GUN
SAFETYKNOB
GROUND CONNECTION

DISPLACEMENT PUMP
5
*Included in KIT.001X
NOTE: Fix parts 11 and 14 with loctite 542 or
similar (wait 1 hour before start running the unit)
Nº REF. DESCRIPTION Q
PIN
TIE
PACKING NUT
FEMALE GLAND
PACKING
MALE GLAND
NUT
HOUSING
JOINT
SLEEVE
ROD
WASHER
BALL
PISTON
PIN
RETAINER
JOINT
BALL
VALVE
FLUID SUCCION
BODY
COVER
FILTER
SPRING
SCREW
SUPPORT
JOINT
BODY
RACORD
PLUG
RACORD
FILTER 60 MESH
FILTER 100 MESH
FILTER 200 MESH
1
2
3
*4
*5
*6
7
8
9
10
11
12
13
14
15
16
17
19
20
21
22
25
26
27
28
29
30
31
32
33
34
G.100.XX*
C.PA1.01
C.200.01X
B.120.00X
B.130.01X
B.130.02
B.130.03X
C.TU1.01
B.110.00X
B.100.01
B.100.02
B.100.03
B.140.01X
C.B01.01
B.150.00
B.100.05
B.100.04X
B.100.06
CBO.104
B.160.00X
D.100.00X
D.910.00
G.100.02X
G.100.XX*
G.100.04
C.TA9.01
G.100.03X
G.100.07
G.100.01X
G.100.06X
G.100.09X
G.100.08X
G.100.20
G.100.05
G.100.21
1
3
1
2
12
2
3
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
3
8
2
7
4
6
5
11
9
12
10
6
4
5
13 14
15 16
17
20
19
25
26
27
28
29
30
31
32
33
34
22
21

AIR MOTOR
6
1
2
3
10
6
21
13
15
22 23
4
25
7
8
9
11
12
14
29
16 26
20
30
24
27
28
5
17
19
18
CAP
JOINT
CYLINDER
ROD
SUPPORT
YOKE
ROD
SCREW
CLIP
PISTON
STEM
JOINT
ROD
JOINT
SLEEVE
JOINT
PLATE
BASE
SCREW
SCREW
ROCKER
SPRING
ROD
CLIP
NUT
JOINT
JOINT
JOINT
RETAINER
GROUND
1
1
1
2
1
1
1
2
2
1
2
1
1
1
1
1
2
1
6
16
2
2
2
2
4
1
2
2
1
1
Nº REF. DESCRIPCION Q
A.110.02
CJT.001
A.210.01
A.120.04
A.220.07
A.120.08
A.221.00
CTJ.002
A.240.02
A.240.01
A.122.00
CJT.005
A.220.11
CJT.007
CB2.015
CJT.006
A.130.02
A.250.01
CTA.001
CTC.001
A.120.01
A.120.02
A.120.03
A.120.05
A.120.06
A.150.02
A.120.10
A.220.09
CAR.125
TIE.GR
1
2
3
4
5
6
7
8
9
10
*11
*12
13
*14
15
*16
17
18
19
20
21
22
23
*24
25
26
*27
*28
29
30
*Included in KIT.054

TROUBLESHOOTINGGUIDE
Restricted line or inadequate air supply.
Insufficient air pressure, closed or clogged air valves, etc.
Exhausted fluid supply.
Obstructed fluid hose, gun or dispensing valve.
Clogged spray tip or filters.
Clogged filters.
Throat packings nut too tight or to loose.
Exhausted fluid supply.
Obstructed fluid hose or gun.
Worn spray tip.
Held open or worn intake valve.
Held open or worn fluid piston or packings.
Exhausted fluid supply.
Check valves need adjustment.
Held open or worn intake valve.
Held open or worn fluid piston or packings.
100-150
200-250
300-350
100-150
200-250
300-350
100-150
200-250
300-350
100-150
200-250
300-350
100-150
200-250
300-350
100-150
200-250
300-350
.021’’
21.20
21.40
21.60
.023’’
23.20
23.40
23.60
.025’’
25.20
25.40
25.60
.027’’
27.20
27.40
27.60
.029’’
29.20
29.40
29.60
.031’’
31.20
31.40
31.60
0.30
0.45
0.64
0.87
1.13
1.36
1.74
2.08
2.49
2.91
3.33
3.86
100-150
200-250
300-350
100-150
200-250
300-350
100-150
200-250
300-350
100-150
200-250
300-350
100-150
200-250
300-350
100-150
200-250
300-350
.009’’
9.20
9.40
9.60
.011’’
11.20
11.40
11.60
.013’’
13.20
13.40
13.60
.015’’
15.20
15.40
15.60
.017’’
17.20
17.40
17.60
.019’’
19.20
19.40
19.60
0.48 MM. 0.43 MM. 0.38 MM. 0.33 MM. 0.28 MM. 0.23 MM.
0.79 MM. 0.74 MM. 0.68 MM. 0.63 MM. 0.58 MM. 0.53 MM.
ORIFICE SIZE
MM / INCHES FLOW IN LITRES / MIN FAN WIDTH AT 300 MM. ORIFICE SIZE MM / INCHES FLOW IN LITRES / MIN FAN WIDTH AT 300 MM.
TECHNICALDATA
STANDARDSPRAYTIPS
Clear,increase air.
Open, clean.
Refill; purgeall air from pump and fluid lines.
Clear.
Clear or replace.
Clear or replace.
Adjust.
Refilandprime.
Clear.
Replace.
Clear.
Clear or replace.
Refillandprime.
Adjust.
Clear.
Clear or replace.
PROBLEM POSSIBLE CAUSE SOLUTION
Pump. fails
to operate.
Pump operates
but output low
on down stroke.
Erraticor
accelerated
operating.
For trouble free operation is absolutely essential that your sprayer be kept clean and free of residual paint buil-up on the internal parts. It
must be cleaned and lubricated after each use.
7
RECOMMENDEDMAXIMUMAIRSPEED: 60CYCLES/MIN.
FLOWAT60CYCLES/MIN.: 3,6LITRES/MIN.
PUMPRATIO: 30:1.
RECOMMENDEDAIRPRESSURE:FROM2TO7BAR.
MAXIMUMWORKINGPRESSURE: 250BAR.

IMP 005X-OCTUBRE 2019
MBP,S.L.
e-mail:[e-mail] www.mbpspray.com
WARRANTY
1.-
2.-
3.-
M.B.P., will any repairs necessary during the first 12 months after purchase of a new unit, with the exceptions shown
under 1 and 2 below, and under the conditions shown in item 3.
In no case will M.B.P.liability extend beyond repair or repalacement of the equipment. Such liability is limited to the
amount of the original purchase price paid for the unit, minus a reasonable deduction for the timethe unit has been in
service. It is the responsibility of the purchaser under this warranty to ship or deliver the failed paint sprayer to the
authorized service center at the purchaser’s expence. Parts or components covered under this warranty may either
be repaired or replaced at M.B.P. option.
Equipent not covered by M.B.P. warranty. Accessories or components of equipment sold by M.B.P. that are nort
manufactured by M.B.P. are subject to the warranty, if any, of their manufacturer. M.B.P. will provide purchaser with
reasonable assistance in making such claims.
The Industry Department of The Basque Goverment, states that all electric and pneumatic airless equipment
manufacture by M.B.P. S.L., follows the ’’CE’’ standards under the number 83/392/CEE.
MODELO / MODEL TEL - 30 INOX
Este producto cumple con la siguiente directiva de la Comunidad Europea.
This Product complies with the following European Comunity Directive.
Directiva 2014/34/EU Atex sobre máquinas. (Ex II 2G cT6 X)
Machinery Directive 2014/34/EUAtex Directive. (Ex II 2G c T6 X)
APROBADO POR /
APPROVED BY AITOR ORTIZ
FECHA / DATE
MBP, S.L. figura inscrita en el Registro Industrial del País Vasco con el Nº 01/8030 y cumple los
requisitos para el desarrollo de su actividad comercial.
MBP, S.L. is registered in the Industrial Register of the Basque Country with the Nº 01/8030.
DECLARACIONDECONFORMIDAD‘’CE’’
‘’EC’’DECLARATIONOFCONFORMITY
Damage caused by external abuse, customer negligence, or failure to operate the unit in accordance with the
instructionssuppliedwiththeunit.
Normal maintenance items.
Within the first 12 months after purchase, M.B.P. will pay 100% of the cost of covered repairs.