McDantim Trumix TM300 User manual

McDantim, Inc. Limited One Year Warranty
Warranty not valid outside the Con nental USA
If the mechanics of this product are found to be defec ve in materials or workmanship within
one year from the date of purchase, McDantim, Inc. will repair or replace, at its op on, the
defec ve product or component part. If for any reason the original purchaser is unsa sfi ed with the
performance of this product, McDantim, Inc. will, at the purchaser’s op on, replace the product or
refund the original sale price upon return of this product to McDantim, Inc. Please retain receipt
for proof of purchase. Proof of purchase is required for any warranty service or claim. Your receipt is
your warranty card.
LIMITED WARRANTY
McDantim, Inc. warrants each product to be free from defects in material and workmanship under
normal use and service for one year from date of sale. The obliga on of McDantim, Inc. under this
warranty is limited to the replacement of defec ve parts. No ce of defec ve parts must be submi ed
to McDantim, Inc. within one year and 15 days of date of sale. This warranty does not cover
shipping, handling, or freight charges.
DISCLAIMER OF WARRANTY
WARRANTY IS INVALID IF PURCHASER FAILS TO PROPERLY OPERATE AND/OR MAINTAIN THE
PRODUCT. THIS WARRANTY IS NOT TRANSFERABLE TO THIRD PARTIES. THIS WARRANTY IS EXPRESSLY
IN LIEU OF ALL OTHER WARRANTIES AND REPRESENTATIONS, EXPRESSED OR IMPLIED EXCEPT AS
STATED ABOVE. THERE IS NO WARRANTY FOR FITNESS FOR A PARTICULAR PURPOSE OR WARRANTY
OF MERCHANTABILITY.
EXCEPT AS OTHERWISE AGREED HEREIN McDantim, Inc. SHALL NOT BE LIABLE FOR SPECIAL OR
CONSEQUENTIAL DAMAGES, SUCH AS, BUT NOT LIMITED TO DAMAGE TO OR LOSS OF OTHER
PROPERTY OR EQUIPMENT, LOSS OF PROFIT OR REVENUE, LOSS OF USE OF THE PRODUCT , COST
OR REPLACEMENT OF THE PRODUCT, OR CLAIMS BY CUSTOMERS FOR LOSS DUE TO SERVICE
INTERRUPTIONS. THE REMEDIES OF THE PURCHASER SET FORTH HEREIN ARE EXCLUSIVE, AND THE
LIABILITY OF McDantim, Inc. WITH RESPECT TO ANY CONTRACT SHALL NOT, EXCEPT AS EXPRESSLY
PROVIDED HEREIN, EXCEED THE PRICE OF THE EQUIPMENT OR PART ON WHICH SUCH LIABILITY IS
BASED.
This warranty applies only to the original registered purchaser. TAMPERING, ACCIDENT, ABUSE,
NEGLECT, UNAUTHORIZED REPAIRS OR OTHER CAUSES UNRELATED TO DEFECTIVE MATERIALS OR
WORKMANSHIP WILL VOID THIS WARRANTY. McDantim, Inc. neither assumes nor authorizes
any representa ve or other person to assume for us any liability in connec on with the sales or any
shipment of our products.
PLEASE KEEP INSTRUCTIONS WITH YOUR PURCHASE RECEIPT FOR YOUR RECORDS!
WARNING:
This product can expose you to chemicals including lead and lead compounds, which are known to
the State of California to cause cancer and birth defects or reproduc ve harm. For more informa on,
go to www.P65Warnings.ca.gov
Thank You for purchasing the McDantim, Inc. Trumix®Gas Blender Panel. Our goal is to give
you the most dependable, accurate and straight forward blender possible for food packaging,
welding or other related uses and products. We want you to be thoroughly happy with your new
system and would like to hear from you if for any reason you are, in any way, displeased.
The McDantim, Inc. Trumix®Gas Blender Panel is simple to install and use. It is extremely
accurate, reliable and requires li le maintenance. Properly installed, and supplied with clean, dry
gas, your Trumix®Gas Blender Panel will provide a perfect supply of mixed gas for many years.
Please take the  me to read and understand the instruc ons, the system and the cau ons.
While the system is simple there are inherent dangers in working with pressurized gases. Pressure
vessels and storage tanks, which contain both liquids and pressurized gases, can explode or
rupture and cause serious injury or death if over-pressurized or used incorrectly. Be 100% sure
you understand the implica ons of what you are doing whenever you set up, turn on or modify
this or any system. Check with your equipment supplier (in the case of storage tanks especially)
to be sure you are not exceeding any safety limits. If you have any doubt concerning the safety
of your system, get advice from or have the work done by a qualifi ed specialist.
Cau on
With the Trumix®Gas Blender Panel you are dealing with pressurized gases. Serious
injury or death can result from improper installa on, use or service. All work on these
systems should be carried out by qualifi ed personnel only! Before a emp ng any work
on this system be sure to read and understand these and any other instruc ons that relate
to the equipment involved in these systems! The dangers include, but are not limited to,
EXPLOSION if the maximum safe pressures for any of the individual components of the
system are exceeded or ASPHYXIATION if gases are released or leaked into a confi ned
area. If you have any ques ons regarding the safety of these systems do not proceed
with the installa on or opera on un l you are 100% certain as to their safety!
Installa on Instruc ons for the
Trumix®Gas Blender Panel
TM300 / TM900

Installa on Instruc ons
Step 1: Determine the best loca on for the blender! Please consider the following:
A) Select a loca on that minimizes the chance of accidental damage to the blender.
B) Select a loca on as near as is prac cal to both the supply sources and the supplied equipment.
C) Select a loca on allowing convenient access to the shut off valve for servicing.
D) Mount panel in a weather-proof area only.
Step 2: Mount panel to wall!
Step 3: Hook up gas supply and outlet!
A) Use only the gases shown on the panel label(s).
B) Make sure you are supplying the panel with clean, dry gases that are between the minimum and maximum pressures as
indicated on the panel label.
C) Turn shut-off valve(s) on panel to the off posi on.
D) Make sure the tubing from the gas sources is compa ble with the fi  ngs on the panel.
DO NOT ATTEMPT TO REMOVE INLET OR OUTLET FITTINGS.
E) Install appropriate tubing adaptors in the inlet fi  ngs. Be sure to use thread sealant and back-up wrenches. Connect
gases supply lines to inlet fi  ngs.
F) Confi rm that your system and related equipment is safe and ready for pressurized mixed gas.
G) Connect mixed gas supply tube to mixed gas outlet fi  ng.
H) Turn on the supply gases and check supply system and fi  ngs for leaks.
I) Adjust outlet pressure regulator to desired outlet pressure. Read outlet pressure on Outlet Pressure Gauge.
J) Open mixed gas supply shut off valve and check system for leaks.
Opera on Guidelines and Helpful Hints
NOTES:
1) Supply the panel with clean gases.
2) Be sure no liquid can get into the blender as this will render it useless and void the warranty.
3) Some fi  ngs on the panel do not have standard US threads, and should not be removed with out checking with
McDantim, Inc.!
4) NEVER EXCEED THE RECOMMENDED PRESSURES FOR ANY PART OF YOUR SYSTEM!
Adjus ng the outlet pressure.
1) Close shut-off valve. This allows you to read pressure changes quickly.
2) Pull out the adjus ng stem of regulator.
3) Read pressure on pressure gauge.
4) Adjust pressure. Increase by turning clockwise. Note: When decreasing pressure, always reduce pressure to below the
desired level and then increase to desired se ng.
5) Push in adjus ng stem of regulator to lock.
6) Open shut-off valve.
Trouble-shoo ng: No Outlet Gas
1) Close shut-off valve. Check pressure on pressure gauge. If pressure is low or zero, check:
a) Outlet regulator for adjustment. (See “Adjus ng the outlet pressure” above.)
b) Both supply gases. (One or both could be empty, turned off or out of adjustment.)
c) For blockage of either supply line or for a closed valve within the supply system. (The blender shuts off if either
supply gas is unavailable.)
If pressure is good:
d) Open shut-off valve completely.
2) If you con nue to have no gas, close shut-off valve, remove tubing from outlet, open shut-off valve and check for gas
fl o w .
3) If you s ll have no supply gas, call McDantim, Inc. or your gas supplier or service person. There are no user-
serviceable parts within the panel. Anything done to the internal parts will aff ect the blend and void the warranty.
If you encounter other ques ons or problems call:
McDantim, Inc. [phone] or [phone].
Warning
With this or any compressed gas system there
are certain dangers. If you do not have the
experience to understand these dangers use a
professional installer.
Trumix®Gas Blender Panel
Installaon Instrucons
Use primary regulators on your
gas source suitable for your panel
specicaons.
Example: If your inlet pressure
label states “Min. inlet pressure
120 psi” then you must provide at
least 120 psi to the Blender Panel.
Mixed Gas Out
Use reinforced tubing suitable for inlet pressure.
Gas #1 Gas #2
NOTE:
Gases can be a combinaon of any two of the
following: Argon, Helium, Nitrogen and CO2.
Your Trumix®Gas Blender is factory set to insure
a precise gas combinaon and blend. Please
reference the labels on your Trumix®TM300 or
TM900 for the exact gases and pressure required.
DO NOT SUBSTITUTE GASES.
Example shown on this page is a TM300
set for 25% CO2 with a Balance gas of N2. 1. Use thread sealant.
2. Do not remove ngs.
3. Use back-up wrenches.

Installa on Instruc ons
Step 1: Determine the best loca on for the blender! Please consider the following:
A) Select a loca on that minimizes the chance of accidental damage to the blender.
B) Select a loca on as near as is prac cal to both the supply sources and the supplied equipment.
C) Select a loca on allowing convenient access to the shut off valve for servicing.
D) Mount panel in a weather-proof area only.
Step 2: Mount panel to wall!
Step 3: Hook up gas supply and outlet!
A) Use only the gases shown on the panel label(s).
B) Make sure you are supplying the panel with clean, dry gases that are between the minimum and maximum pressures as
indicated on the panel label.
C) Turn shut-off valve(s) on panel to the off posi on.
D) Make sure the tubing from the gas sources is compa ble with the fi  ngs on the panel.
DO NOT ATTEMPT TO REMOVE INLET OR OUTLET FITTINGS.
E) Install appropriate tubing adaptors in the inlet fi  ngs. Be sure to use thread sealant and back-up wrenches. Connect
gases supply lines to inlet fi  ngs.
F) Confi rm that your system and related equipment is safe and ready for pressurized mixed gas.
G) Connect mixed gas supply tube to mixed gas outlet fi  ng.
H) Turn on the supply gases and check supply system and fi  ngs for leaks.
I) Adjust outlet pressure regulator to desired outlet pressure. Read outlet pressure on Outlet Pressure Gauge.
J) Open mixed gas supply shut off valve and check system for leaks.
Opera on Guidelines and Helpful Hints
NOTES:
1) Supply the panel with clean gases.
2) Be sure no liquid can get into the blender as this will render it useless and void the warranty.
3) Some fi  ngs on the panel do not have standard US threads, and should not be removed with out checking with
McDantim, Inc.!
4) NEVER EXCEED THE RECOMMENDED PRESSURES FOR ANY PART OF YOUR SYSTEM!
Adjus ng the outlet pressure.
1) Close shut-off valve. This allows you to read pressure changes quickly.
2) Pull out the adjus ng stem of regulator.
3) Read pressure on pressure gauge.
4) Adjust pressure. Increase by turning clockwise. Note: When decreasing pressure, always reduce pressure to below the
desired level and then increase to desired se ng.
5) Push in adjus ng stem of regulator to lock.
6) Open shut-off valve.
Trouble-shoo ng: No Outlet Gas
1) Close shut-off valve. Check pressure on pressure gauge. If pressure is low or zero, check:
a) Outlet regulator for adjustment. (See “Adjus ng the outlet pressure” above.)
b) Both supply gases. (One or both could be empty, turned off or out of adjustment.)
c) For blockage of either supply line or for a closed valve within the supply system. (The blender shuts off if either
supply gas is unavailable.)
If pressure is good:
d) Open shut-off valve completely.
2) If you con nue to have no gas, close shut-off valve, remove tubing from outlet, open shut-off valve and check for gas
fl o w .
3) If you s ll have no supply gas, call McDantim, Inc. or your gas supplier or service person. There are no user-
serviceable parts within the panel. Anything done to the internal parts will aff ect the blend and void the warranty.
If you encounter other ques ons or problems call:
McDantim, Inc. [phone] or [phone].
Warning
With this or any compressed gas system there
are certain dangers. If you do not have the
experience to understand these dangers use a
professional installer.
Trumix®Gas Blender Panel
Installaon Instrucons
Use primary regulators on your
gas source suitable for your panel
specicaons.
Example: If your inlet pressure
label states “Min. inlet pressure
120 psi” then you must provide at
least 120 psi to the Blender Panel.
Mixed Gas Out
Use reinforced tubing suitable for inlet pressure.
Gas #1 Gas #2
NOTE:
Gases can be a combinaon of any two of the
following: Argon, Helium, Nitrogen and CO2.
Your Trumix®Gas Blender is factory set to insure
a precise gas combinaon and blend. Please
reference the labels on your Trumix®TM300 or
TM900 for the exact gases and pressure required.
DO NOT SUBSTITUTE GASES.
Example shown on this page is a TM300
set for 25% CO2 with a Balance gas of N2. 1. Use thread sealant.
2. Do not remove ngs.
3. Use back-up wrenches.

McDantim, Inc. Limited One Year Warranty
Warranty not valid outside the Con nental USA
If the mechanics of this product are found to be defec ve in materials or workmanship within
one year from the date of purchase, McDantim, Inc. will repair or replace, at its op on, the
defec ve product or component part. If for any reason the original purchaser is unsa sfi ed with the
performance of this product, McDantim, Inc. will, at the purchaser’s op on, replace the product or
refund the original sale price upon return of this product to McDantim, Inc. Please retain receipt
for proof of purchase. Proof of purchase is required for any warranty service or claim. Your receipt is
your warranty card.
LIMITED WARRANTY
McDantim, Inc. warrants each product to be free from defects in material and workmanship under
normal use and service for one year from date of sale. The obliga on of McDantim, Inc. under this
warranty is limited to the replacement of defec ve parts. No ce of defec ve parts must be submi ed
to McDantim, Inc. within one year and 15 days of date of sale. This warranty does not cover
shipping, handling, or freight charges.
DISCLAIMER OF WARRANTY
WARRANTY IS INVALID IF PURCHASER FAILS TO PROPERLY OPERATE AND/OR MAINTAIN THE
PRODUCT. THIS WARRANTY IS NOT TRANSFERABLE TO THIRD PARTIES. THIS WARRANTY IS EXPRESSLY
IN LIEU OF ALL OTHER WARRANTIES AND REPRESENTATIONS, EXPRESSED OR IMPLIED EXCEPT AS
STATED ABOVE. THERE IS NO WARRANTY FOR FITNESS FOR A PARTICULAR PURPOSE OR WARRANTY
OF MERCHANTABILITY.
EXCEPT AS OTHERWISE AGREED HEREIN McDantim, Inc. SHALL NOT BE LIABLE FOR SPECIAL OR
CONSEQUENTIAL DAMAGES, SUCH AS, BUT NOT LIMITED TO DAMAGE TO OR LOSS OF OTHER
PROPERTY OR EQUIPMENT, LOSS OF PROFIT OR REVENUE, LOSS OF USE OF THE PRODUCT , COST
OR REPLACEMENT OF THE PRODUCT, OR CLAIMS BY CUSTOMERS FOR LOSS DUE TO SERVICE
INTERRUPTIONS. THE REMEDIES OF THE PURCHASER SET FORTH HEREIN ARE EXCLUSIVE, AND THE
LIABILITY OF McDantim, Inc. WITH RESPECT TO ANY CONTRACT SHALL NOT, EXCEPT AS EXPRESSLY
PROVIDED HEREIN, EXCEED THE PRICE OF THE EQUIPMENT OR PART ON WHICH SUCH LIABILITY IS
BASED.
This warranty applies only to the original registered purchaser. TAMPERING, ACCIDENT, ABUSE,
NEGLECT, UNAUTHORIZED REPAIRS OR OTHER CAUSES UNRELATED TO DEFECTIVE MATERIALS OR
WORKMANSHIP WILL VOID THIS WARRANTY. McDantim, Inc. neither assumes nor authorizes
any representa ve or other person to assume for us any liability in connec on with the sales or any
shipment of our products.
PLEASE KEEP INSTRUCTIONS WITH YOUR PURCHASE RECEIPT FOR YOUR RECORDS!
WARNING:
This product can expose you to chemicals including lead and lead compounds, which are known to
the State of California to cause cancer and birth defects or reproduc ve harm. For more informa on,
go to www.P65Warnings.ca.gov
Thank You for purchasing the McDantim, Inc. Trumix®Gas Blender Panel. Our goal is to give
you the most dependable, accurate and straight forward blender possible for food packaging,
welding or other related uses and products. We want you to be thoroughly happy with your new
system and would like to hear from you if for any reason you are, in any way, displeased.
The McDantim, Inc. Trumix®Gas Blender Panel is simple to install and use. It is extremely
accurate, reliable and requires li le maintenance. Properly installed, and supplied with clean, dry
gas, your Trumix®Gas Blender Panel will provide a perfect supply of mixed gas for many years.
Please take the  me to read and understand the instruc ons, the system and the cau ons.
While the system is simple there are inherent dangers in working with pressurized gases. Pressure
vessels and storage tanks, which contain both liquids and pressurized gases, can explode or
rupture and cause serious injury or death if over-pressurized or used incorrectly. Be 100% sure
you understand the implica ons of what you are doing whenever you set up, turn on or modify
this or any system. Check with your equipment supplier (in the case of storage tanks especially)
to be sure you are not exceeding any safety limits. If you have any doubt concerning the safety
of your system, get advice from or have the work done by a qualifi ed specialist.
Cau on
With the Trumix®Gas Blender Panel you are dealing with pressurized gases. Serious
injury or death can result from improper installa on, use or service. All work on these
systems should be carried out by qualifi ed personnel only! Before a emp ng any work
on this system be sure to read and understand these and any other instruc ons that relate
to the equipment involved in these systems! The dangers include, but are not limited to,
EXPLOSION if the maximum safe pressures for any of the individual components of the
system are exceeded or ASPHYXIATION if gases are released or leaked into a confi ned
area. If you have any ques ons regarding the safety of these systems do not proceed
with the installa on or opera on un l you are 100% certain as to their safety!
Installa on Instruc ons for the
Trumix®Gas Blender Panel
TM300 / TM900