MCZ PLASMA 75 LH WOOD User manual

CLOSED FIREPLACE
PLASMA 75 RH/LH WOOD
PLASMA 95 RH/LH WOOD
INSTALLATION GUIDE GB
Instructions in English

II
TABLE OF CONTENTS
TABLE OF CONTENTS .................................................................................................. II
INTRODUCTION ..........................................................................................................1
1WARNINGS AND WARRANTY CONDITIONS .................................................................2
2INSTALLATION.........................................................................................................7
3FLUE .......................................................................................................................8
4DIMENSIONS AND TECHNICAL FEATURES.................................................................16
5UNPACKING...........................................................................................................21
6POSITIONING ........................................................................................................23
7OPERATING MODE..................................................................................................26
8AIR INLETS............................................................................................................27
9CHOICE OF FUEL.....................................................................................................32
10OPERATION .........................................................................................................34
11EASY GOING.........................................................................................................38
12EASY SWITCH.......................................................................................................40
13ACCESSORIES.......................................................................................................44
14MAINTENANCE AND CLEANING..............................................................................47

1
INTRODUCTION
Technical Dept. - All rights reserved - Reproduction prohibited
Dear Customer,
our products are designed and manufactured in compliance with European reference standards for construction products (EN13240 for
wood-burning range cookers, EN14785 for pellet-burning appliances, EN13229 for replaces/wood-burning inserts and EN 12815 for
wood-burning range cookers), with high quality materials and extensive experience in transformation processes.
Carefully read the instructions in this manual to ensure the best performance.
This installation guide is an integral part of the product: ensure that the manual is always supplied with the appliance, even if it changes
owner. If the manual is lost, you can request another copy from the local Technical Dept. or download it directly from the company’s
website.
All local regulations, including those referring to national and European standards, must be observed when installing the appliance.
In Italy, for the installation of systems with a biomass below 35KW, refer to the Ministerial Decree 37/08 and the qualied installation
technician with the suitable requirements must issue a certicate of compliance for the system installed. (By system we intend
Stove+Flue+Air vent).
REVISIONS TO THE PUBLICATION
The content of this manual is strictly technical and the property of MCZ Group Spa.
No part of this manual may be translated into other languages, adapted and/or reproduced, even in part in other mechanical and/or
electronic form or media, for photocopies, recordings or other, without the prior written authorisation from MCZ Group Spa.
The company reserves the right to make changes to the product at any time without prior notice. The proprietary company reserves its
rights according to law.
CARE OF THE MANUAL AND HOW TO CONSULT IT
• Take care of this manual and store it in an easily and quickly accessible place.
• Should this manual be lost or destroyed, request a copy from your retailer or directly from the authorised Technical assistance
department. It can also be downloaded from the company’s website.
• “Bold text”requires special attention.
• “Text in italics”is used to draw attention to other paragraphs in the manual or for any additional clarications.
• “Note”provides the reader with additional information.
SYMBOLS USED IN THE MANUAL
ATTENTION:
carefully read the corresponding message as failure to comply with the information provided may result
in serious damage to the product and danger to the persons who use it.
INFORMATION:
failure to comply with these provisions will compromise use of the product.
OPERATING SEQUENCES:
sequence of buttons to be pressed to access the menus or perform adjustments.
MANUAL
carefully read this manual or the relative instructions.

2
1WARNINGS AND WARRANTY CONDITIONS
SAFETY WARNINGS
• Installation, electrical connection, operating check and maintenance
must only be carried out by authorised and qualied personnel.
• Install the product in accordance with all local and national legislation
and regulations in force in the region or state.
• Only use the fuel recommended by the manufacturer. The product must not be
used as an incinerator.
• It is strictly forbidden to use alcohol, petrol, liquid fuel for lanterns, diesel, bio-
ethanol, uids for lighting charcoal or similar liquids to light/rekindle the ame
in these devices. Keep these ammable liquids well away from the appliance
when in use.
• Do not insert fuel other than wood in the combustion chamber.
• The instructions provided in this manual must always be complied with to
ensure the product and any electronic appliances connected to it are used
correctly and accidents are prevented.
• The user, or whoever is operating the product, must read and fully understand
the content of this installation guide before performing any operation. Errors or
incorrect settings may cause hazardous conditions and/or incorrect operation.
• Do not climb on or lean on the product.
• Do not dry linen on the product. Any drying racks or the like must be kept at a
safe distance from the product. Fire hazard.
• All liability for improper use of the product is entirely borne by the user and relieves
the manufacturer of any civil and criminal liability.
• Any type of tampering or unauthorised replacement with non-original spare
parts may be hazardous for the operator’s safety and relieves the company of
any civil and criminal liability.

3
1WARNINGS AND WARRANTY CONDITIONS
Technical Dept. - All rights reserved - Reproduction prohibited
• Many surfaces of the product get very hot (door, handle, glass, smoke outlet
pipes, etc.). Avoid coming into contact with these parts, without
adequate protective clothing or suitable implements, such as gloves
with thermal protection or“cold handle”operating systems.
• It is forbidden to operate the product with the door open or the glass
broken.
• The product must be powered by an electrical system that is equipped with an
eective earthing system.
• Do not wash the product with water.
• Donot standforalongtime in frontoftheproduct in operation.Do not overheat
the room you are in and where the product is installed. This may cause injuries
and health problems.
• Install the product in a location that does not present a re hazard and is
equipped with power and air supplies and smoke outlets.
• Do not use water to put the re out.
• In the event the chimney catches re never open the fuel loading door. Then
contact the competent authorities.
• The product and the cladding must be stored in a dry place and must not be
exposed to weathering.
• It is recommended not to remove the feet that support the product in order
to ensure adequate insulation, especially if the ooring is made of ammable
materials.
• Special maintenance must only be performed by authorised and qualied
personnel.
• Assess the static conditions of the surface on which the weight of the product
will rest and provide suitable insulation if it is made of combustible material
(e.g. wood, tted carpet or plastic).

4
1WARNINGS AND WARRANTY CONDITIONS
INFORMATION:
Please contact the retailer or qualied personnel authorised by the company to resolve a problem.
• Only use the fuel specied by the manufacturer.
• When the product is switched on for the rst time, it is normal for it to emit smoke due to the paint heating for the rst time.
Therefore make sure the room in which it is installed is well ventilated.
• Check and clean the smoke outlet pipes regularly (chimney tting).
• The product is not a cooking appliance.
• Store this installation and user manual with care as it must accompany the product for the duration of its useful life. If the product is
sold or transferred to another user, always ensure the manual is also handed over.
INTENDED USE
The product only works with wood and must be installed indoors.
WARRANTY CONDITIONS
The company guarantees the product, with the exception of parts subject to normal wear (listed on the following page), for a
period of 2 (two) years from the date of purchase attested by:
• a document to serve as proof of purchase (invoice and/or receipt) that shows the name of the vendor and the date on which the
purchase was made;
• forwarding of the completed warranty certicate within 8 days of purchase.
Furthermore, in order for the guarantee to be valid, the device must be installed and calibrated by qualied personnel, and where
necessary, the user must be issued with a declaration of conformity and correct functioning of the product.
We recommend testing the product before completion with the relative nishes (cladding, painting of walls, etc.).
Installations that do not meet the current standards, improper use and lack of maintenance as expected by the manufacturer, void the
product warranty.
The warranty is valid on the condition that the instructions and warnings contained in the user and maintenance manual are observed,
and therefore the product is used correctly.
Replacement of the entire system or repair of one of its components does not extend the warranty period, and the original expiry date
remains unchanged.
The warranty covers the replacement or free repair of parts recognised as being faulty at source due to manufacturing defects.
In the event of a fault, to benet from the warranty, the customer must keep the warranty certicate and provide it along with the
document given at the time of purchase to theTechnical Service Centre.

5
1WARNINGS AND WARRANTY CONDITIONS
Technical Dept. - All rights reserved - Reproduction prohibited
EXCLUSIONS
The warranty does not cover malfunctions and/or damage to the appliance that arise due to the following causes:
• Damage caused during transport and/or handling
• all parts that develop faults due to negligence or improper use, incorrect maintenance, installation that does not comply with the
manufacturer’s instructions (always refer to the installation guide provided with the appliance)
• incorrect sizing with regard to the use or faults in the installation or failure to implement the necessary measures to ensure proper
execution
• improper overheating of the equipment, i.e. the use of fuels not conforming to the types and quantities indicated in the instructions
provided
• further damage caused by incorrect user operations in an attempt to x the initial fault
• worsening of the damage caused by the user continuing to operate the appliance even after the fault has been detected
• in the presence of a boiler, any corrosion, deposits or breakage caused by water ow, condensation, hardness or acidity of the water,
improperly performed descaling treatments, lack of water, mud or limescale deposits
• ineciency of chimneys, ues or parts of the system aecting the appliance
• damage caused by tampering with the appliance, atmospheric agents, natural disasters, vandalism, electrical discharges, res, faults
in the electric and/or hydraulic system.
The following are also excluded from this warranty:
• parts subject to normal wear such as gaskets, glass, cladding and cast iron grilles, painted, chrome-plated or gilded parts, handles
and electric cables, bulbs, indicator lights, knobs, all parts which can be removed from the rebox.
• Variations in colour of the painted or ceramic/serpentine parts and crazed ceramics as they are natural characteristics of the material
and product use.
• masonry work
• system parts (if present) not supplied by the manufacturer
Any technical operations on the product to remove the aforementioned defects and consequent damage must be agreed upon with the
Technical Service Centre, who reserves the right to accept the relative appointment or not. However, said operations shall not be carried
out under warranty but as technical support to be granted as part of any potentially and specically agreed conditions and in accordance
with the fees in force for the work to be carried out.
The user will also be charged for any costs incurred to remedy the incorrect technical operations, tampering or damage to the appliance,
not attributable to original faults.
Without prejudice to the legal or regulatory limits, the warranty does not cover the containment of atmospheric and acoustic pollution.
The company declines all liability for any damage which may be caused, directly or indirectly, to persons, animals or objects as
a consequence of non compliance with any provision specied in the manual, especially warnings regarding installation, use
and maintenance of the appliance.

6
1WARNINGS AND WARRANTY CONDITIONS
SPARE PARTS
In the event of a malfunction, consult the retailer who shall forward the call to the Technical Assistance Department.
Only use original spare parts. The retailer or service centre can provide all necessary information regarding spare parts.
We do not recommend waiting for the parts to get worn out before having them replaced. It is crucial to perform regular maintenance
checks.
The company declines all liability if the product and any other accessory is used improperly or modied without
authorisation.
All parts must be replaced with original spare parts.
WARNINGS FOR CORRECT DISPOSAL OF THE PRODUCT.
The owner is the sole party responsible for demolishing and disposing of the product.This must be performed in compliance with the laws
related to safety and environmental protection in force in their country.
At the end of its working life, the product must not be disposed of as urban waste.
It must be taken to a dierentiated waste collection centre set up by the local authorities or to a retailer that provides this service.
Separating and recycling prevents potential negative eects on the environment and health (often caused by inappropriately disposing of
product parts). It also allows materials to be recovered in order to obtain signicant savings of energy and resources.

7
2INSTALLATION
Technical Dept. - All rights reserved - Reproduction prohibited
INSTALLATION
FOREWORD
The installation position must be chosen according to the room, smoke extraction system and ue. Check with local authorities whether
there are any restrictive regulations in force regarding the combustion air inlet, the smoke outlet system, the ue or the chimneypot. The
manufacturer declines all responsibility in the event of installations that do not comply with the laws in force, incorrect room air exchange,
electrical connection non-compliant with the standards and inappropriate use of the appliance. The installation must be carried out by
a qualied technician, who must issue a declaration of conformity of the system to the purchaser and shall assume full responsibility for
nal installation and consequent good operation of the product.
In particular one must ensure that:
• there is a suitable combustion air inlet and smoke outlet in compliance with the type of product installed
• other stoves or devices installed do not cause depression in the room where the product is installed
• when the product is switched on there is no reux of smoke in the room
• smoke extraction takes place in full safety (sizing, smoke seal, distances from ammable materials...).
We especially recommend to check the data tags of the ue for the safety distances that must be observed in presence
of combustible materials and the type of insulating material to be used. These indications must be followed strictly
to prevent serious harm to people and to the integrity of the home. Installation of the appliance must ensure easy access to
clean the appliance itself, the smoke outlet pipes and the ue. It is forbidden to install the product in rooms with a re hazard.
Installation in studio ats, bedrooms and bathrooms is only permitted with sealed or closed appliances equipped with
suitable combustion air ducting directly outside. Always maintain adequate distance and protection in order to prevent
the product from coming into contact with water.
In the event there are several appliances installed, the external air inlet must be sized accordingly.
MINIMUM DISTANCES
We recommend installing the stove away from walls and furniture, with a minimum clearance to allow eective aeration of the appliance
and a good distribution of heat in the room. Observe the distances from ammable or heat-sensitive objects (sofas, furniture, wood
panelling, etc.) as specied.The front distance from combustible materials needs to be at least the measurement provided in the product
technical data.
If particularly delicate objects are present, such as furniture, curtains or sofas, increase the product clearance accordingly.
If the oor is made of combustible material, it is recommended to use a protection made of non-combustible material (steel, glass...) that
also protects the front from any falling combusted material during cleaning operations.
The appliance must be installed on a oor with adequate load capacity.
If the existing construction does not meet this requirement, one must take appropriate measures (for example a load distribution plate).

AP
(B)
8
3FLUE
FLUE
FOREWORD
This Flue chapter has been drawn up with reference to the provisions of European regulations (EN13384 - EN1443 - EN1856 - EN1457).
The chapter provides indications for installing an ecient and correct ue but is under no circumstances to substitute the regulations in
force, which the qualied manufacturer must be in possession of. Check with local authorities whether there are any restrictive regulations
in force regarding the combustion air intake, the smoke outlet system, the ue or the chimneypot.
The Company declines all liability relating to the poor functioning of the stove if this is due to the use of an insuciently sized ue in
violation of the standards in force.
FLUE
The ue or chimney is of great importance for the proper operation of a solid fuel-burning heating appliance with natural draught, as
modern heating appliances have high eciency with cooler ue gas and consequently less draught, it is therefore essential that the ue is
built to a high standard and always kept in perfect working order. A ue that serves a wood-burning appliance must be at least category
T400 (or greater if the appliance requires so) and resistant to soot res. Smoke must be extracted through a single ue made of insulated
steel or an existing ue that complies with the intended use (B).
A simple air shaft made of cement must be suitably piped. In both solutions there must be an inspection cap and/or inspection hatch (AP).
It is prohibited to connect more than one wood/pellet or any other type of appliance (vent cowling...) to the same ue.
FLUE

ABC
D
E
A
B
C
D
15° E
F
A
B
C
D
E
30°
F
9
3FLUE
Technical Dept. - All rights reserved - Reproduction prohibited
TECHNICAL CHARACTERISTICS
Have the eciency of the ue checked by an authorised technician.
The ue must be sealed against ue gases, in a vertical direction without narrowing, be made with materials impermeable to smoke,
condensation, thermally insulated and suitable to resist normal mechanical stress over time (we recommend replaces made of A/316
or refractory material with insulated round section double chamber). It must be suitably insulated externally to avoid condensation
and reduce smoke cooling. It must be separated from combustible or easily ammable materials via an air gap or insulating materials:
check the distance specied by the chimney manufacturer according to EN1443. The chimney opening must be in the same room as the
appliance, or at most in the adjoining room, and have a soot and condensation collection chamber beneath the opening, and be accessible
via a sealed metal hatch.
The ue needs to be safely connected to a ground contact in observance of regulations in force.
FLAT ROOF
ROOF AT 15°
ROOF AT 30°
A = 0.50 metres
B = DISTANCE > 2 metres
C = DISTANCE < 2 metres
D = 0.50 metres
E = TECHNICAL VOLUME
A = MIN. 1.00 metre
B = DISTANCE > 1.85 metres
C = DISTANCE < 1.85 metres
D = 0.50 metres ABOVE
HIGHEST POINT
E = 0.50 metres
F = REFLUX AREA
A = MIN. 1.30 metres
B = DISTANCE > 1.50 metres
C = DISTANCE < 1.50 metres
D = 0.50 metres ABOVE
HIGHEST POINT
E = 0.80 metres
F = REFLUX AREA
FIGURE 2
FIGURE 3
FIGURE 4

A
B
D
60°
E
C
F
A
B
C
D
E
45°
F
10
3FLUE
ROOF AT 60° ROOF AT 45°
SIZING
The negative pressure (draught) of a ue also depends on its height. Check the negative pressure with the values indicated in the technical
specications.The minimum height of the ue is 3.5 metres.
The interior cross-section of the ue can be round (best), square or rectangular (the ratio between the internal sides must be ≤1.5) with
the sides joined with a minimum radius of 20 mm. The size of the section must be at least equal to that of the appliance outlet (smaller
diameters must be conrmed by an adequate system sizing calculation).
The cross-sections/lengths of the chimneys shown in the technical data tables are indications for correct installation. Any alternative
congurations must be correctly sized in accordance with the general method of calculation of UNI EN13384-1 or other proven eciency
methods.
Some examples of ues available on the market are provided below:
AISI 316 steel chimney with
double chamber insulated with
ceramic bre or equivalent
resistant up to 400°C.
Refractory chimney with
double insulated chamber and
external lightweight concrete
cladding with cellular material
such as clay.
Traditional square-section clay
chimney with insulating empty
inserts.
Avoid products with an internal
rectangular section where the
larger side is 1.5 times the
smaller side (e.g. 20x40 or
15x30).
EXCELLENT GOOD POOR VERY POOR
A = MIN. 2.60 metres
B = DISTANCE > 1.20 metres
C = DISTANCE < 1.20 metres
D = 0.50 metres ABOVE HIGHEST POINT
E = 2.10 metres
F = REFLUX AREA
A = MIN. 2.00 metres
B = DISTANCE > 1.30 metres
C = DISTANCE < 1.30 metres
D = 0.50 metres ABOVE HIGHEST POINT
E = 1.50 metres
F = REFLUX AREA
FIGURE 5 FIGURE 6

1
9
9
2
3
4
5
6
7
8
11
3FLUE
Technical Dept. - All rights reserved - Reproduction prohibited
MAINTENANCE
The ue must be kept clean, since the deposit of soot or unburned oils reduces the cross-section reducing the draught, thus compromising
the ecient operation of the product and, if large build-ups accumulate, they can catch re. The ue and chimneypot must be cleaned
and checked by a qualied chimney sweep at least once a year. Once the maintenance has been performed, request a written declaration
that the device is safe.
Failure to clean the system jeopardises safety.
CHIMNEYPOT
The chimneypot is a crucial element for correct operation of the heating appliance: we recommend a windproof chimneypot (A), see
Figure 7.
The area of the opening for smoke
extraction must be at least double the
cross-section of the ue/piped system,
and arranged so that the smoke outlet
is ensured even in the presence of
strong wind. The chimneypot must
prevent rain, snow or animals from
entering the chimney. The height of
outow into the atmosphere must
be beyond the reux area caused by
the shape of the roof or any nearby
obstacles (see Figures 2-3-4-5-6).
CHIMNEY COMPONENTS
KEY:
(1) CHIMNEYPOT
(2) REFLUX CHANNEL
(3) SMOKE DUCT
(4) THERMAL INSULATION
(5) OUTSIDE WALL
(6) CHIMNEY FITTING
(7) SMOKE DUCT
(8) HEAT GENERATOR
(9) INSPECTION ACCESS PANEL
FIGURE 7
FIGURE 8

A
BB
A
CD
B
12
3FLUE
EXTERNAL AIR INLET
It is mandatory to provide an adequate external air inlet that supplies the combustion air required for the product to work properly. The
ow of air between the outside and the installation room may be direct, through an inlet in an external wall of the room (preferable
solution see Figure 9 c); or indirect, via air intake from adjoining rooms and connecting permanently with the installation room (see Figure
9 a/b). Adjoining areas may not include sleeping areas, bathrooms, garages or general areas with a re hazard. During installation it is
required to check the minimum clearances required to draw air from outside. Take into account the presence of doors and windows that
could interfere with the proper ow of air to the product (see diagram below).
The air inlet must have a minimum total net area of 180 cm2 (for replaces/inserts): the surface must be increased accordingly if within
the room there are other active generators (for example: electric fan for stale air extraction, range cooker hood, other stoves, etc...),
which could cause a depression in the room. One must verify that, with all the equipment on, the pressure drop between the room and
the outside does not exceed a value of 4 Pa. If required, increase the intake section of the air inlet, which must be made at oor level and
always protected with a bird-proof outer protection grid and in such a way that it cannot be obstructed by any object.
You can connect the air required for combustion directly to the external air inlet, with a non-compressible pipe (e.g. spiral). For air ducts
up to 3 m, increase the cross-section by approximately 5%, longer ducts increase it by 15%.
FIGURE 9 a - indirectly from inside the room FIGURE 9 b - indirectly from the adjacent
room
A=INTERNAL AIR INLET
B=ROOM TO BE VENTILATED
C=INCREASE OF THE GAP UNDER THE DOOR
D=EXTERNAL AIR INLET
FIGURE 9 c - directly from outside

13
3FLUE
Technical Dept. - All rights reserved - Reproduction prohibited
For closed replaces installed in studio ats, bedrooms and bathrooms (where allowed), it is mandatory to connect the combustion air to
the outside. In particular for sealed products the connection must be sealed in order not to compromise the overall sealed characteristic
of the system.
DISTANCE (metres) The air inlet must be at a distance of:
1.5 m BELOW Doors, windows, smoke outlets, cavities, ....
1.5 m HORIZONTALLY Doors, windows, smoke outlets, cavities, ....
0.3 m ABOVE Doors, windows, smoke outlets, cavities, ....
1.5 m AT A DISTANCE from smoke outlet
CONNECTION TO THE FLUE
The connection between the ue and the appliance must be via a smoke duct that complies with EN 1856-2. To connect the replace to
the chimney ue or to a ceiling connection that is not coaxial to the unit’s smoke outlet, changes of direction must be made using open
bends no greater than 45° with respect to the vertical. The same solution needs to be used to connect the replace to the chimney (see
gure below)
The diameter of the smoke duct must be equal to or greater than that of the appliance outlet. Any increase in the cross-section is only
allowed at the connection to the chimney
EXAMPLE OF CLOSED FIREPLACE FITTING
A. CERAMIC FIBRE INSULATION
B. SMOKE FITTING
C. CHIMNEY FLUE
D. HOOD GRID
TYPICAL DIAGRAM OF A CORRECTLY LAID CHIMNEY
FLUE WITH, AT THE FOOT OF THE EXTERNAL UPDRAFT
SECTION, THE POSITIONING OF A CHAMBER WITH A SEALED
HATCH TO COLLECT AND REMOVE THE SOLID MATERIALS
PRODUCED DURING COMBUSTION.

14
3FLUE
TYPE OF SYSTEM SMOKE DUCT (SMOKE FITTING)
Minimum vertical length 1.5 metres
Maximum length
(with 1 MAX 45° bend)
4.5 metres
Use smoke ducts that are able to withstand the unit operating temperatures (min. T400). The use of exible metal hoses made of
bre cement or aluminium is forbidden. For direction changes, we always recommend the use of a Tee tting with an
inspection cap ensuring easy access to clean the pipes. Always ensure that the inspection cap is put back in place and sealed hermetically
with the relevant seal intact after cleaning.
It is prohibited to connect more than one appliance to the same smoke duct, or the discharge from hoods above it. It is forbidden to extract
the combustion products directly through the wall, whether into indoor spaces or outdoors.
The smoke duct must be installed observing the safety distances from ammable materials as specied on its rating plate (e.g. G400=
400 mm).

P
2
U
1
s
P
s
U
P
3
15
3FLUE
Technical Dept. - All rights reserved - Reproduction prohibited
EXAMPLES OF CORRECT INSTALLATION
1. Installation of Ø200mm ue with hole for the passage
of the pipe increased by:
minimum 100mm around the pipe if next to non
ammable parts such as cement, brick, etc.; or
minimum 400mm around the pipe (or as required by data
tags) if next to ammable parts such as wood etc.
In both cases, install suitable insulation between the ue
and the ceiling.
Always check and comply with the plate data of the
ue, specically the minimum safety distances from
combustible materials.
The previous rules also apply for holes made in walls.
2. Old ue, minimum pipe Ø200mm with the inclusion of
an external access door for chimney cleaning.
3. External ue made of insulated stainless steel pipes,
i.e. with double walls minimum Ø200mm: all securely
mounted on the wall.With windproof chimneypot.
NOTE: with closed replaces maintain the safety distance
indications with the included insulation indications.
FIGURE 11
U = insulation
s = inspection access panel
P = air inlet

851
420 211
260
417
Ø200
151
240
605
834
1634
358 611 665
Ø150 C
A
Ø100-150
B
Ø100-150
B
A
B
SEMITRANCIO VENTILAZIONE NATURALE
SEMITRANCI Ø100-150
CINGRESSO ARIA COMBURENTE Ø 150
16
4DIMENSIONS AND TECHNICAL FEATURES
PLASMA 75 RH WOOD DIMENSIONS
NATURAL VENTILATION KNOCKOUT HOLE
KNOCKOUT HOLES Ø 100-150
COMBUSTION AIR INLET Ø 150

C
A
Ø200
A
B
SEMITRANCIO VENTILAZIONE NATURALE
SEMITRANCI Ø100-150
CINGRESSO ARIA COMBURENTE Ø 150
417
260
605
152
240
211 420
850
Ø100-150
B
Ø100-150
B
834 589 Ø150
358 611 665
1634
17
4DIMENSIONS AND TECHNICAL FEATURES
Technical Dept. - All rights reserved - Reproduction prohibited
PLASMA 75 LH WOOD DIMENSIONS
NATURAL VENTILATION KNOCKOUT HOLE
KNOCKOUT HOLES Ø 100-150
COMBUSTION AIR INLET Ø 150

Ø150 C
A
Ø100-150
B
Ø100-150
B
A
B
SEMITRANCIO VENTILAZIONE NATURALE
SEMITRANCI Ø100-150
CINGRESSO ARIA COMBURENTE Ø 150
515
Ø200
259
1046
265
500
154
240
605
589
1030
359 611 665
1634
18
4DIMENSIONS AND TECHNICAL FEATURES
PLASMA 95 RH WOOD DIMENSIONS
NATURAL VENTILATION KNOCKOUT HOLE
KNOCKOUT HOLES Ø 100-150
COMBUSTION AIR INLET Ø 150