MD SPORTS 1625802 User manual

MODEL: 1625802
ASSEMBLY INSTRUCTIONS
TM
VM Innovations
ATTENTION
DO NOT RETURN
TO THE STORE
Contact
MD Sports
Customer Service
* For additional resources and Frequently
Ask Questions, please visit us at
themdsports.com

LIMITED 90 DAYS WARRANTY
NOTICE!
STAPLE YOUR RECEIPT HERE
This product is covered by a limited warranty that is effective for 90 days from the date of purchase. If, during
the limited warranty period, a part is found to be defective or breaks, we will offer replacement parts at no
cost to you, the customer. The only exceptions to the warranty include mainframes, table tops, playing
surfaces, batteries or tools.
The above warranty will not apply in cases of damages due to improper usage, alteration, misuse, abuse,
accidental damage or neglect.
This Limited Warranty gives you specific legal rights and you may also have other rights which vary from one
State (province) to another.
A PURCHASE RECEIPT (or other proof of purchase) will be required before any warranty service is initiated.
For all requests for warranty service, please feel free to contact our Consumer Service Department at :
Please be aware of your product’s Limited Warranty for the return/refund policy from the store, We, at Medal
Sports, can not handle the product which is out of product’s limited warranty since we only provide available
parts. Thank you!
PLEASE CONTACT US BEFORE RETURNING
THE PRODUCT TO THE STORE.
WEBSITE: www.themdsports.com
1 - Please leave your name, address, phone number, model number, parts needed on the answering
machine if there is no attendant. Failure to do so will result in a delay in shipping parts to you.
2 - Please review the replacement parts list and make sure that you have all of your parts before begin-
ning assembly. For questions that may arise or for missing/damaged parts, please contact us.
3 - Since you build all tables upside down, please inspect tabletops or playing surfaces right away before
putting together, all damaged table tops/playing surfaces need to be returned to the store. Please
contact with retailer for their return policy.
www.themdsports.com
1625802 1
(Continued on the next page.)

CAUTION !
ASSEMBLY TIPS
TOOLS REQUIRED
Phillips Screwdriver - Not Included
Standard (Flat Head Screwdriver) - Not Included
Allen Wrench - Included
WARNING:


WARNING: Adult Assembly Required.
IMPORTANT NOTICE!
Power Tools
-Set Low Torque
High Torque
over tightened
1 - Please read the instructions carefully, and follow all assembly, operation and safety
instructions properly in order to avoid damage and injury. For the assembly, at least two
adults are required.
2 - Some figures or drawings may not look exactly like your product. Please read and under-
stand the text before beginning each assembly step.
Do not use or keep product
outdoors. For indoor use only.
No wet/humid conditions.
Keep away from petsNo Children in
Assembly Area
Electric Screwdrivers may be helpful during assembly; however,
please set a low torque and use extreme caution.
1 - This product is intended for INDOOR use only.
2 - Please do not sit, climb or lean on the product.
3 - Please do not drag the product when moving it in order to avoid damaging the legs.
4 - Please only use spray furniture polish to clean the exterior surfaces of the product.
5 - This is not a child's toy, adult supervision is required for children playing this game.
X2
Strong Adults Needed
www.themdsports.com
1625802 2
(Continued on the next page.)

www.themdsports.com
1625802 3
(Continued on the next page.)
1625802 PARTS LIST
910 11 12
13 14 15 16
2 3 41
x2 x2 x1 x2
6 7 85
x2 x4 x2
x2 x2 x2 x2
x11 x11 x2 x4
x2
18 19 20
x16 x16 x2
21
x4
22
x8
23
x8
24
x4
25
x24
26
x16
27
x8
28
x36
29
x26
30
x26
17
x2
31
x4
32
x8
Side Apron
Left Leg
Inside Ball Cup Goal Box Ball Catcher Ball Return
Channel
Support Brace Leg Leveler Outside
Ball Cup
End Apron Playfield Right Leg
Player - Red/Black
Player - Blue/Black 5-Hole Rod
2-Hole Rod Rod Washer
Scorer Holder Rod End Cap Handle
“L” Bracket
3.5 x 38mm
Screw
M6 x 15mm
Bolt
4 x 25mm
Flat Head Screw
4 x 15mm
Screw
M6 x 35mm Bolt
T4 x 25mm Bolt T5 x 15mm Bolt4 mm Nut
Rod Bumper Slide Scorer
3-Hole Rod

www.themdsports.com
1625802 4
(Continued on the next page.)
1625802 PARTS LIST
1625802 PRE-INSTALLED PARTS
P1 P2
x4 x16 x2
P3
x2
P4
33
x14
34
x2
35 36
x1
P5 P6
x1 x8
4 x 12mm
Screw
37
x4
Plastic “L” Bracket
Rod Bushing Ball Return Cover Goal Cover
Soccer Ball Allen Key
M6 Nut
Logo Plate
38
x2
39
x4
Top Slat Board 4 x 25mm Round
Head Screw
40
x6
41
x4
Triangle Board
Cap
Triangle Board
x4
Stop Ring
x24
M6 Spring
Lock Washer
42
M6 Washer
x8
42 43
ASSEMBLY INSTRUCTIONS:
1. Find a clean, level place to begin the assembly of your Foosball Table. We recommend that two adults work
together to assemble this Foosball Table.
2. Remove all the parts from the box and verify that you have all of the listed parts as shown on the parts list page.
Carefully cut or tear the four corners of the box so that the bottom of the box can be used as your work surface.
P7
x4
Square Nut with
Screws
Top corner

www.themdsports.com
1625802 5
(Continued on the next page.)
FIG. 2
FIG. 1
FIG. 3
FIG.2
Note: Do not tighten the screws at this step.
FIG.3
X 8
X 2
1
25
X 2
P3
X 1
P5
X 8
P6
X 1
3
X 16
25
X 2
X 4
X 2
2
39
38
2
2
1
1
25
P3
P5
X 2
P4
2
38
39
FIG.1
3. Attach the End Aprons (#2) to the Top Slat Boards (#38) using two Screws (#39) per End Apron. See FIG. 1.
P4
P6
4. Attach the End Aprons (#2) to the Side Aprons (#1) using four Screws (#25) per End Apron. See FIG. 2.
5. Attach the Playfield (#3), with the graphics facing down, on the Side and End Aprons (#1 & #2) using Sixteen
Screws (#25). See FIG. 3.
2
25
3
1

www.themdsports.com
1625802 6
(Continued on the next page.)
FIG. 4
FIG. 5
FIG.4
FIG.5
X 2 X 24
X 6
6
7X 4
28
40
40
40
28
28
28
40
6
FIG. 5A
1
1
7
28
28
28
6
FIG. 5B
6. Attach the right and left legs (#4 & #5) to the end aprons (#2) using two bolts (#26), two spring lock washer (#42)
and two washer (#43) per leg.
7. Attach the metal “L” brackets (#24) to the side aprons (#1) using two bolts (#27) and two spring lock washer (#42) .
See FIG. 4A.
8. Attach the metal “L” brackets (#24) to the legs using two bolts (#26) and two spring lock washer (#42) . See FIG. 4.
9. Attach the L Bracket (#40) to Support Braces (#6) using six screws (#28) per Support Braces. See FIG.5A.
10. Attach the Support Braces (#6) to the Side Aprons (#1) using four Screws (#28) per support brace. Attach the
Support Braces (#6) to the Playfield (#3) using two Screws (#28) per support brace. See FIG. 5B.
11. Screw the Leg Levelers (#7) into the bottom of each leg.
X 16
X 2
X 2
26
X 4
24
X 8
27
X 24
42
X 8
43
4
5
X 4
P7
26
26
24
27
42
42
42
43
4
2
1
P7
FIG. 4A
5
5
4
4

www.themdsports.com
1625802 7
(Continued on the next page.)
FIG. 6
FIG.6
12. Attach the Ball Catchers (#11) to the inside of Side Aprons (#1) using four Screws (#28) per Ball Catcher.
13. Attach the Goal Boxes (#10) to the inside of End Aprons (#2) using two Screws (#28) per Goal Box.
14. Attach one end of the Ball Return Channel (#12) to the Ball Catcher (#11) and the other end to the
Goal Box (#10) as shown in FIG.6. Repeat for the other Ball Return Channel (#12).
15. Lift the table assembly from the floor with two strong adults, turn it over, and set table on its legs in the
location where you play. Go back and make sure that all connections are tight.
X 2
X 2
X 2
12
11
10
X 12
28
12
12
10 11
28
28

www.themdsports.com
1625802 8
(Continued on the next page.)
FIG.7
FIG. 7
16. Attach the Outside Ball Cup (#8) and Inside Ball Cup (#9) to Side Apron (#1) using five screws (#33) per side.
See FIG. 7A.
X 2
8
X 2
9
X 14
33
X 4
37
X 4
41
8
933
33
outside
inside
37
33
37
41
FIG. 7B
FIG. 7A
17. Attach the Triangle Board (#37) on to playfield (#3) using one screw (#33) per triangle board. Cover the
screw by inserting triangle board cap (#41) into the Triangle Board (#37) See FIG. 7 & 7B.
DO NOT LEAN THE
TABLE ON ITS LEGS
HOLD TABLE
HOLD TABLE DO NO T HOLD THE LEGS
CAUTION: Two strong adults are recommended to turn
the table over as shown.
1. Life the table off of the ground.
2. Turn the table over.
3. Place it on all four feet at the same time on the ground.

www.themdsports.com
1625802 9
(Continued on the next page.)
FIG.8
18. Slide the Player Rods (#15-17) through the Rod Bushings (#P2) on one Side Apron (#1) in the order
as shown in Fig.8 and 8A.
Note: The player Rods have a hole at their end where the Handles (#23) will go.
FIG. 8
Note: Players of the same team
color should have Handles on
the same side, and each team’s
players should be facing their
opponent.
X 11
X 2
X 2
X 16
X 16
X 26
X 26
X 11
X 4
17
18
19
29
30
14
13
15
16
X 4
35
X 16
P2
= Blue
= Red
ORDER OF PLAYERS
(Overhead View)
16
16
16
16
15
15
17
17
or/o
17
18
18
19
19
14
13
FIG. 8B
FIG. 8A
The Hole /
EI agujero
The Hole
P2
P2
19. Assemble (#15, #16 and #17)-Player Rods, place the Rod Bumpers (#19), Rod Washers (#18), and
Players (#13 and #14) onto the Player Rods (#15, #16 and #17) in the order as shown in Fig.8, 8A and 8B.
20. Now insert the Player Rods through the Rod Bushings (#P2) on the opposite Side Apron (#1).
21. Attach the Players (#13 or #14) to the Player Rods (#15 -17) using one Bolt (#29) and one Nut (#30) per Player.
See FIG.8C.
Note: The goalie should be at the left side of each player.
FIG. 8C 29
30 35 19
16
19
18
18
22. Attach the Stop Rings (#35) to the Rods (#16) using one Bolt (#29) and one Nut (#30) per Stop Ring. See FIG.8C.