MD SPORTS 39003 User manual

Please contact us before returning the product to the store.
Toll Free: 877-472-4296
MODEL/MODÈLE: 39003
INSTRUCTIONS D`ASSEMBLAGE
S'il vous plaît nous contacter avant de retourner le produit
au magasin.
Numéro sans frais: 877-472-4296

LIMITED 90 DAYS WARRANTY
1
This product is covered by a limited warranty that is effective for 90 days
from the date of purchase. The warranty covers any defects in parts and
workmanship.
This Limited Warranty gives you specific legal rights and you may also have
other rights which very from one state (province) to another.
If, during the limited warranty period, a part is found to be defective or
breaks, we will offer replacement part at no cost to you, the customer. The
only exceptions to the warranty include main frames, tabletops, playing
surfaces, batteries or tools.
The above warranty will not apply in cases of damages due to improper
usage, alteration, misuse, abuse, accidental damage or neglect.
Attention: Since you build all tables upside down, please inspect table tops
and playing surfaces right away before putting together.
“PLEASE SAVE THESE INSTRUCTIONS
AND PURCHASE RECEIPT!”
A PURCHASE RECEIPT (or other proof of purchase date) will be required
before any warranty service is initiated. All requests for warranty service can
be submitted by email, in writing or by contacting our Consumer service
Department at:
TOLL FREE: 877-472-4296
WEBSITE: www.medalsports.com.tw
*Please do not call our 800 NUMBER as well as email us. This will result in
duplicate orders and charges will occur.
*Please note that all damaged table tops need to be returned to the store.
We do not replace any tabletops or playing surfaces.
PLEASE CONTACT US BEFORE RETURNING THE
PRODUCT TO THE STORE. THANK YOU VERY MUCH!

Phillips Screwdriver – Not Included
Standard (Flat Head Screwdriver) – Not Included
Allen Wrench - Included
TOOLS REQUIRED:
ASSEMBLY TIPS:
:

!



!
2
IMPORTANT NOTICE! Please contact us before returning the product to the store.
Please read the instructions carefully, and follow all assembly, operation or safety instructions
properly in order to avoid damage or injury. For the assembly, at least two adults are required.
Some figures or drawings may not look exactly like your product. Please read and understand
the text before beginning each assembly step.
1 -
2 -
Please Keep Your Instructions! Your Model number is necessary should you need to contact
us. Please read through this instruction manual book to familiarize yourself with all parts and
assembly steps. Kindly refer to the parts identifier below and be sure that all parts have been
included.
Although we are dedicated to giving our customers the best product possible, a question may
arise or parts may be missing. If you are missing parts, or, if you have any questions, please
contact our fast and friendly service centre on:
1 - This product is intended for INDOOR use only.
2 - Please Do Not sit, climb or lean on the game table.
3 - Please Do Not drag the table when moving it in order to avoid the damaged on the legs.
4 - Please only use spray furniture polish to clean the exterior surfaces on the game table.
5 - This is not a child's toy, adult supervision is required for children playing this game.
877-472-4296
Power Tools
- Set Low Torgue
High Torque
over tightened
CAUTION !
Electric Screwdrivers may be helpful during
assembly; however, please set a low torque
and use extreme caution.

3
39003 PARTS LIST
Main Cabinet
1 Piece
Lower Side Apron
2 Pieces
Lower End Apron
2 Pieces
Leg Cabinet - A
4 Pieces
Leg Cabinet - B
4 Pieces
Bottom Leg Base
4 Pieces
Decorative Plastic Panel
4 Pieces
8 x 38mm Bolt
16 Pieces
8 x 19mm Washer
28 Pieces
Plastic Screw Cap
8 Pieces
EVA Pad
12 Pieces
M6.5 T - Nut
16 Pieces
8 x 50mm Bolt
6 Pieces
M8 Nut
6 Pieces
4 x 32
Flat Head Screw
40 Pieces
Allen Key
1 Piece
Wrench
1 Piece
3 x 18
Flat Head Screw
8 Pieces
Triangle
1 Piece
6.5 x 38mm Bolt
16 Pieces Leg Leveler
4 Pieces
Cue
2 Pieces
Chalk
2 Pieces
Billiard Ball
1 Set
Plastic Brush
1 Piece
Plastic Barrel Nut
32 Pieces
Pre-installed Pre-installed
Pre-installed Pre-installed
Table Tennis Surface-A
2 Pieces
Table Tennis Surface-B
1 Piece
Plastic Net Post
2 Pieces
Table Tennis Net
1 Piece
Table Tennis Paddle
2 Pieces
Table Tennis Ball
2 Pieces
Plastic Screw Anchor
4 Pieces
Bottom Cue Rack
1 Piece
Top Cue Rack
1 Piece
4 x 50mm
Flat Head Screw
4 Pieces
Plastic Dowel
6 Pieces
Side Pocket
2 Pieces
Corner Pocket
4 Pieces
12345
6 7 8 9 10
11 12 13 14 15
16 17 18 19 20
21 22 23 24 25
26 27 28 29 30
31 32 33 34 35
36 37 38 4A
M8 T - Nut
20 Pieces
Pre-installed
5A

FIG. 1
4
FIG.1
ASSEMBLY INSTRUCTIONS
1. Find a clean, level place to begin the assembly of your 2 in 1 Multi Table. The table will be
assembled upside down and then turned over on its legs once the assembly completed.
This game table is heavy, and turning it over will require at least four strong adults.
2. Remove all the parts from the box and verify that you have all of the listed parts as shown
on the parts identifier below. Carefully cut or tear the four corners of the box so that the
bottom of the box can be used as your work surface.
3. Fold one Leg Cabinet - A (#4) and one Leg Cabinet - B (#5) into an L-shape and attach the two
sides together using six Screws (#12) per Leg Cabinet. See FIG.1.
4. Attach the Bottom Leg Base (#6) to the Leg Cabinet using four Screws (#12). See FIG.1.
5. Repeat the steps above for the other Legs.
12
12
4
5
5
6
4A 5A
36

FIG. 2
5
FIG.2
6. Attach the previous-assembled Legs onto the support frame of the Cabinet (#1) using
four Bolts (#8) and four Washers (#9) per Leg. See FIG.2.
NOTE: PLEASE DON’T LOCK THE BOLTS TOO TIGHT AT THIS STEP.
7. Screw the Leg Leveler (#15) into the Bottom Leg Base (#6). See FIG.2.
15
6
34
35

FIG. 3
6
FIG.3
8. Attach the Lower Side Apron (#2) to the Legs using two Bolts (#10), four Washers (#9), two
M8 Nuts (#11) and four Bolts (#14) per Lower Side Apron. See FIG.3.
NOTE: PLEASE DON’T LOCK THE BOLTS TOO TIGHT AT THIS STEP.
9. Attach the Lower End Apron (#2) to the Legs using one Bolt (#10), two Washers (#9), one
M8 Nut (#11) and four Bolts (#14) per Lower End Apron. See FIG.3.
NOTE: PLEASE DON’T LOCK THE BOLTS TOO TIGHT AT THIS STEP.
10. Repeat the steps above for the other Lower Side Apron and Lower End Apron.
11. Go back and make sure that all connections are closed tightly.
11 14
14
10
3
2
9
911
10
9
9

13
7
FIG. 4
7
FIG.4
12. Slide the Decorative Plastic Panel (#7) to the Leg using two Screws (#13) per Decorative
Plastic Panel. See FIG.4.
13. Repeat the steps above for the other Decorative Plastic Panels.

FIG. 5
8
FIG.5
15. Place two Screw Caps (#37) to cover the opening on the Decorative Plastic Panel (#7).
See FIG 5. And repeat the steps for the other Screw Caps.
14. Lift the table assembly from the floor with four strong adults, turn it over, and set table on
its legs in the location where you play.
37
7
37
37
HOLD TABLE CABINET DO NOT
HOLD THE
LEGS
DO NOT LEAN THE
TABLE ON ITS LEGS!
CAUTION: Four strong adults are recommended to turn the table over as shown.
1. Lift the table off the ground.
2. Turn the table over.
3. Place it on all four feet at the same time on the ground.

FIG.6
16. Tear off the backside paper of the EVA Pad (#38) and stick them at the bottom of the Table
Tennis Surface - A and B (#23 and #24). See FIG.6A.
17. Insert the Plastic Dowel (#33) into the holes on the Table Tennis Surface. See FIG.6B.
And assemble the Table Tennis Surface - A (#23) and Table Tennis Surface - B (#24)
together.
18. Place the Table Tennis Surface (#23 & #24) onto the billiard surface and insert the
Net Posts (#25) and Net (#27). See FIG.6.
38
38
23
23
23
24
33
33
25
25
27
FIG.6
FIG.6B
FIG.6A
9