MEDCUORE Purocare Eco+ User manual

User Manual
Manufactured & Marketed by:
MedCuore Medical Solutions Private Limited
No 110, 1st Floor, East Madha Church Street, Royapuram, Chennai,
Tamil Nadu 600013
www.medcuore.com

Always unplug the power plug of the device before moving,
cleaning or carrying out other maintenance.
Do not turn on the device if the composite filter and front
cover panel are not installed properly.
Do not use the device if the power cord, the plug, or the
device itself is damaged.
Do not use the device in environment with high ambient
temperature, such as bathroom, toilet or kitchen.
Do not excessively twist, pull or bend the power cord, as it
may damage the power cord. When the power cord is
damaged, have it replaced with a genuine power cord
purchased from the manufacturer or after-sales service
department
Ensure a minimum distance of 20cm between the air inlets
and the wall or other objects.
Remove dust, hair and particles from the air inlet to prevent
the reduction of air intake. Cover the air inlet and outlet
when the device is not in use, to prevent dust, hair or other
particles from falling into the device.
Note: Before opening the product, please open the front
cover and remove all filter packing tapes.
WARNINGS
2 3
Table of Contents 1 Safety Information1.
1. Safety
1.1 Safety Information
1.2 Symbols Used
2. About device
2.1 Intended Use
2.2 Use Environment
2.3 Product Overview
2.4 Controls Overview
2.5 Product Features
2.6 Product Specifications
2.7 Nano Photocatalyst
2.8 Composite Filters
3. Using the device
3.1 Getting Started
3.2 Initial Operation
3.3 Front Cover Indicators
3.4 Remote Control
4. Maintenance
4.1 Cleaning
4.2 Filter Replacement
5. Troubleshooting
6. Warranty
3
3
5
6
6
6
7
8
8
9
10
11
12
12
12
15
16
18
18
18
20
21
21
Read this user manual carefully before you use
the device, and save it for future reference.

4 5
1.2 Symbols Used
Do not obstruct the air inlet and outlet by placing objects on
the outlet or in front of the air inlet.
Always move or lift the device only by using the handle
provided on top of the device.
Use only the original Purocare Eco+ filters specially
intended for this device. Do not use any other filters.
Do not insert fingers or objects into the air inlet or outlet to
prevent physical injury or malfunctioning of the device.
Do not insert or unplug the device/power plug with wet
hand to avoid electric shock.
This device is not a toy. This device shall not be used by
children less then 8 years of age without adult supervision.
Do not sit or stand on the device. Do not lean on or tilt the
device.
Do not use any acid and alkaline liquid for cleaning the
machine to prevent electric shock or damage.
Do not let water or any other liquid enter the device to
avoid electric shock or damage.
Use a soft cloth to gently wipe the device or use a small
brush to remove dust from the air inlet and outlet while
cleaning.
In case of abnormal operational condition, unplug the
power plug immediately and send it to the product
maintenance center for repair.
1.1 Safety Information
Symbol Symbol Description
Manufacturer
Device Serial Number
CE mark is a protected conformity
mark of European Community
Read User manual before
using the product
For indoor and household use only
ROHS Compliant Device
Device tested to comply with FCC
standards
Sleep mode
Child Lock
Icon Indicator/Wind Speed Indicator
This way up
Keep Dry
Handle with Care

6 7
2.3 Product Overview2.1 Intended Use
This device is intended to remove contaminants such as
particulate matter (soot, pollen, allergens), volatile components,
microbes and other harmful substances from the air inorder to
improve the indoor air quality.
2.2 Use Environment
This device is designed for use in indoor/enclosed spaces with
an applicable area of 30-50m and shall not be used for
outdoors or other inappropriate environments.
Operating Environment Conditions
Temperature
Humidity
Atmospheric Pressure
5 C - 40 C
15% - 95% non-condensing
700hPa - 1060hPa
1 - Front Cover and Panel
2 - Button Controls
3 - Remote Control Placement
4 - Air Outlet
5 - Air Inlet
6 - Composite Filter
7 - Nano Photocatalyst
8 - Negative Ion Generator
9 - Remote Control
10 - User Manual
Best suited for indoor applications
2
o o

8 9
2.6 Product Specifications2.4 Control Overview
11 - On/Off Button 12 - Wind Speed Button
13 - Automatic Mode Button 14 - Timing Button
2.5 Features
Specifications
Model Name
Rated Voltage
Rated Frequency
Purocare Eco+
220V AC
50Hz
11
12
13
14
Rated Power
Operating Power
Purification Efficiency
(Removal Rate)
Applicable Area
Clean Air Delivery Rate
Air Volume
Dimensions
Weight
35W
Four - Speed Operation:
High Speed: 35W
Medium Speed: 28W
Low Speed: 24W
Sleep: 10W
Particulate matter >0.3μm: 99.5%
Bacterial colony removal (%): 99.99%
PM2.5: 99.8%
Formaldehyde: 71.3%
TVOC: 91.8%
30 - 50 m
250 CFM/425 m /h
480 m /h
310 x 139x 394 mm
3.5 kg
UV-C Lamp for
Disinfection
Nano-Peco
Technology
Set Timer Composite
Filter
Controlled
Negative Ion
Energy Saving
Operation
2
3
Noise 38dB - 47dB
3

10 11
2.8 Composite Filter2.7 Nano Photocatalyst
Nano photocatalyst works on a high-tech frontier purification
technology, which is composed of nano spraying and special
ultraviolet-c lamp for disinfection.
Advantages of Nano photocatalyst
1. Thorough purification: It enables decomposition rather
than adsorption thereby implementing a qualitative change
rather than quantitative change.
2. Extensive purification: Ensures complete decomposition of
almost all the pollutants, especially bacteria and viruses that
are not easily perceived by human beings.
3. Practical purification: There is no saturation problem,
hence there is no need to replace the catalyst element making
it economic and practical, convenient maintenance, long life
and high efficiency.
4. Safe purification: The final products of purification are
harmless molecules such as carbon dioxide and water, which
are harmless to the human body and non-polluting to the
environment.
5. Safety protection: The UV lamp tube is covered with
Composite filter is composed of primary effect filter + HEPA
filter + activated carbon filter + zeolite + catalyst.
The primary effect filter screen is mainly used to filter larger
particles; HEPA filter is to remove soot, pollen, allergic
substances, viruses and other substances above 0.3 micron in
the air; Activated carbon filter has a property of strong
adsorption of toluene, formaldehyde and other odor in the air
and other harmful substances, and can catalyze the
decomposition of harmful substances.; Zeolite + catalyst can
balance the activated carbon that cannot filter the remaining
gas.
The filter changing cycle is about 8 months and is based on 8
hours of mid-range operation per day. When the filters needs
replacement, the device will remind the user by blinking the
Sleep mode/Filter timing indicator; Please reset after replacing
the new filter by pressing the wind speed button for 3 seconds
to reset.
Note: the primary effect filter is removable and washable.
Please clean or replace it after working for 100-500 hours.
multiple layers of
titanium dioxide spraying
net, which completely
solve the problem of UV
leakage.

12 13
3.1 Getting Started
3.2 Initial Operation
If the air purifier does not start when you press the On
button, please check if the filter and the front panel have
been installed properly. If the filter and the front panel are
not properly installed, the air purifier with the safety design
will not work normally.
Do not use this product in a humid environment, such as a
toilet, because use of the product in a humid environment
may accelerate filter loss and cause damage to
components.
If the product is used in an environment with smoke or oil
fumes, the filter of the product will be covered by the tar of
the cigarette or oil fumes. Clean the filter often with a
vacuum cleaner so as not to affect the filtering effect.
When using the remote controller for the first time, install
two AAA batteries before use
Precautions before use
Insert the power cord into
the electrical outlet.
1.
2. Press the power button on top of the device.
3. The device will be in standby mode by default when
powered on.
4. Press the Wind speed button to increase the speed of the
fan. Available Speed Settings: Low, Medium and High.
By Default, Low wind speed is enabled when powered on.
3.2 Initial Operation
Look for the LED wind speed indicator on the front panel to
know in which speed setting the device is working.
Low Wind Speed Medium Wind Speed High Wind Speed

14 15
3.3 Front Cover Indicators3.2 Initial Operation
5. Press the Automatic mode button to set the device operation
to automatic. i.e. when automatic mode is enabled, the device
will run in high wind speed for two hours, then in medium wind
speed for two hours and finally in low wind speed for two
hours.
6. Press the timing mode button to set timer for the device to
turn off automatically after the set timing.
Available timer for shutdown: 1 hour, 4 hours & 8 hours.
7. Press the power button again on top of the device to turn off
the device.
A
B
C
D E
F
A - Wind Speed Indicator/Icon Indicator
Turned off when the device is in standby mode. Indicates the
wind speed in which the device is currently operating.
B - Timing Indicator
Turned on when timer is enabled for 1H, 4H or 8H auto
shutdown respectively.
C - Remote Control Receiving Port
D - Sleep mode/Filter Change Indicator
Turned on when the device is working in sleep mode and
blinks when the filter needs replacement.
E - Automatic Mode Indicator
F - Child Lock Indicator

16 17
3.4 Remote Control
1. On/Off button 2. Wind speed button
3. Child lock button 4. Sleep mode button
5. Auto mode button 6. Timing button
1.On/Off button
Enter standby state when power is connected; Press the ON
button, the buzzer rings, and then the low wind speed, the
anion and nano photocatalyst are automatically turned on;
Press the OFF button, all functions stop and enter standby
state automatically.
2. Wind speed button
Wind speed is equipped with four grades, which are sleep, low,
middle and high. The default operation is low when starting up.
Press the wind speed selection button each time, the indicator
light will improve in turn, and the buzzer will ring once each
time.
3. Child lock button
The child lock can be set by remote control. In child lock mode,
the remote control and all the buttons on the machine do not
work but the machine still operates according to the previous
Settings. Unlocking method: Long press the child lock button
for 3 seconds, the child lock mode will be released.
4. Sleep mode button
The sleep mode can be set through the remote control. Press
the sleep mode button of the remote control, and the machine
directly enters the sleep mode.
5. Automatic mode button
Working status for high operation for 2 hours, then mid
operation for 2 hours, then low operation for 2 hours, cycle in
turn.
6. Timing button
Timing control is equipped with four gears, 1H, 4H, 8H and
continuous successively. The default is continuous operation
when starting up. Press the timing selection button each time,
the indicator light will improve in turn, and the buzzer will ring
once each time.
Keep the remote control and the receiving port without barrier,
and make sure the remote control and remote control
receiving window is vertical (vertical remote control distance
within 5 meters)
3.4 Remote Control

18 19
4.1 Cleaning
Be sure to cut off the power when cleaning, maintaining
and replacing the filter.
Wipe the outside of the machine with clean and soft towel.
Open the front panel, take out the filter and use the soft
brush to clean the air inlet grid.
Do not clean any part of the product with gasoline, alcohol,
bleach and other chemical solvents and corrosive cleaners.
To keep the machine running in best status, you are
recommended to regularly clean the machine.
4.2 Filter Replacement
4.2 Filter Replacement
Press the switch button on both
sides of the front cover with your
fingers and remove the front cover
Hold the white ribbon of the
filter with your fingers and
pull it out
Place the new filter with the
white HEPA side facing out
Cover the front panel from the top
down, then press the lower part of
the front panel with your hand until
the two buckles are in place
Long press the wind speed button
for 3 seconds, then complete the
reset.

20 21
5 Troubleshooting 6 Warranty
Problem Check for Solution
Connect the power supply
Whether the power is
turned on
Whether the plug is loose
or short-circuited
Connect or replace the plug
Install the rear panel
Whether the rear panel is
properly installed
Equipment
doesn't turn on
Replace the filter
The filter absorbs too
much odor or smoke
Replace the filterThe filter service time ends
Strange odour
from air outler
Whether the indoor air is
too dry
Increase indoor air
humidity appropriately
The product is placed in
an unventilated area or
there are obstacles nearby
Change placement
position and remove
obstacles
Poor Purification
effect
Removal of foreign matter
Foreign matter blocking
the air outlet or intake
No air outflow at
the air outlet
Install batteries correctly
Whether to install the
battery upside down
Equipped with batteriesBattery installed or not
Replace a new batteryThe battery is dead
Whether the distance and
Angle of remote control
are out of range
Please use within 5 meters
of the front of the machine
Remote control
is not working
6 Warranty
Warranty will be effective from the date of purchase.
Customer must provide the original purchase invoice and duly filled warranty card at the
time of requesting the warranty services, failing to produce the same by customer will
forfeit the right to claim the warranty. Original Purchase Invoice (Invoice with tax) with duly
filled warranty card is must to claim the warranty.
Total warranty period is limited as provided hereunder from the date of Purchase Invoice
irrespective of the period for which the Product was not in use, was not performing properly
or was under breakdown. In the event of repairs of any part or replacement of part (s) or
replacement of Product during the said warranty period, the warranty shall thereafter
continue only for the unexpired period of the original warranty period. The defective part(s)
or Product shall become property of the Company.
Warranty does not cover the replaceable Composite filters, wheels, plastic, and physical
structure of air purifier.
The Company or Company’s authorized Service Centre reserves the right to decide at its
sole discretion, for replacing any defective part with a substitute without affecting the
performance of the Product or of replacement of the Product.
This warranty shall not apply with respect to the Product or any part thereof which has
been subject to, repair/installation by any unauthorized person or use of any accessories
other than those specified by Company or Company’s authorized Service Centre; any
accident or damage during transit; mishandling; unauthorized modifications; input voltage
beyond specifications; riots; commercial use; lightning; use contrary to the operations
specified in the User Manual supplied with the Product; alteration; there is no Cerina
hologram; if unit/part(s) serial No. is mutilated, defaced, or altered; fire, flood or such
occurrences; water; presence of any foreign object or living creature (e.g., rat, lizard,
insect, ants, etc.) inside the product; use of harmful chemicals; usage of Product in an
abnormally corrosive alkaline/acidic atmosphere; and any change or defect resulting due to
improper maintenance or negligent operation of the Product.
The Company or Company’s authorized Service Centre shall not be liable or be deemed to
be in default for any delay or failure in performance resulting directly or indirectly from
causes beyond its reasonable control including delay in epair due to non-availability of any
component or accessory, labour problem, restrictions and regulations of the government,
public movement, war and any unavoidable circumstances, specially vis-à-vis the import of
supplies and raw material or if the Company’s authorized Service Centre is otherwise
prevented from performing its functions under this warranty.
The warranty extended herein is in lieu of implied conditions and warranties under the law
and is confined to the repair(s) of defective parts and does not cover any consequential or
resulting liability, damage or loss arising from such defects in whatsoever circumstance it
may be. Furthermore, the warranty in no case shall extend to the payment of any monetary
consideration in whatsoever circumstances.
This warranty shall be subject to the following terms and conditions:
1.
2.
3.
4.
5.
6.
7.
8.

6 Warranty
6 Warranty
22 23
6 Warranty 6 Warranty
Any physical damage deliberately made on the Air Purifier structure or
cabinet to take undue benefits from Warranty shall be excluded from the
right(s) to claim warranty under any circumstances.
Any Unauthorized Opening(s) and/or any attempt to reverse engineer the
product including but not limited to De-compilation, Reassembling or any
way to open the cabinet by any unauthorized person will waive the complete
rights(s) of customer to invoke this Contract of Warranty in any condition(s)
in whatsoever circumstances it may be.
9. Any defect in the electrical installation or wiring at site must be rectified by the
Customer as per the recommendation of Company’s authorized Service Centre
representative. Product power requirements are mentioned on the package and
technical specifications in User Manual. Customer is to contact Service Centre for
any query if site does not meet above requirements and is to get it corrected on their
own as per instructions from the Service Centre.
10. Exclusions of warranty:
11. In the event of any difference or dispute arising with reference to the terms and
conditions of this warranty or their interpretation, the same shall be referred to a sole
arbitrator, who shall be appointed by Company. The decision of the sole arbitrator
shall be final and binding on the parties. Such arbitration proceedings shall be held
at Hyderabad, Telangana, only, and provision of the Arbitration & Conciliation Act
1996 shall apply to the arbitration proceedings.
12. This warranty does not cover cost of labour, transportation of the product from
the place of installation to the Company’s authorized Service Centre and other
incidental expenditures, which shall be borne by the Customer. However, as
mentioned earlier, the Company or Company’s authorized service representative, at
its sole discretion, as the case may be, in compliance with listed terms and
conditions, will determine if it will bear the cost of repair or replacement of faulty
functional part(s) or replacement of the air purifier, including cost of one-time to and
fro transportation from place of installation to the Company’s authorized Service
Centre, if it is determined to be a genuine physical manufacturing defect.
13. While Company’s authorized Service Centre will make every effort to carry out
repairs at the earliest, it is however made explicitly clear that the Company or
Company’s authorized Service Centre is under no obligation to do so in a specified
period.