Medion LIFE P13290 User manual

Operating instructions
MEDION® LIFE®P13290 (MD 31290)
80 cm (32“) Full HD Smart-TV

2
Contents
1. Information about these operating instructions............................................................... 4
1.1. Key to symbols..........................................................................................................................................4
1.2. Proper use...................................................................................................................................................5
2. Package contents.................................................................................................................. 5
3. Safety information ............................................................................................................... 6
3.1. Operating safety.......................................................................................................................................6
3.2. Installation location ................................................................................................................................7
3.3. Ambient temperature ............................................................................................................................8
3.4. Repairs .........................................................................................................................................................8
3.5. Safety when connecting .......................................................................................................................9
3.6. Handling batteries................................................................................................................................ 10
4. EU – Declaration of Conformity ......................................................................................... 11
5. Overview of the device....................................................................................................... 12
5.1. Front .......................................................................................................................................................... 12
5.2. Rear and right-hand side.................................................................................................................... 13
5.3. Remote control...................................................................................................................................... 14
6. Using the device for the first time..................................................................................... 16
6.1. Unpacking ............................................................................................................................................... 16
6.2. Mounting ................................................................................................................................................. 17
6.3. Inserting batteries in the remote control..................................................................................... 18
6.4. Connecting the antenna .................................................................................................................... 18
6.5. Connecting the power supply ......................................................................................................... 18
6.6. Switching the smart TV on and off ................................................................................................. 18
6.7. Channel search when switching on for the first time.............................................................. 19
6.8. Using the multimedia connections................................................................................................ 23
7. Operation ............................................................................................................................ 25
7.1. Channel selection ................................................................................................................................. 25
7.2. Sound settings....................................................................................................................................... 25
7.3. Screen settings....................................................................................................................................... 25
7.4. Displaying information ....................................................................................................................... 26
7.5. Opening the favourites list................................................................................................................26
7.6. Selecting the source ............................................................................................................................27
7.7. Wireless display ..................................................................................................................................... 27
8. Teletext................................................................................................................................ 28
8.1. Using the teletext ................................................................................................................................. 28
9. Using the On-Screen Display menu (OSD menu) ............................................................. 29
9.1. Navigating in the menu...................................................................................................................... 29
10. The menu system in detail ................................................................................................. 29
10.1. Home page.............................................................................................................................................. 29
10.2. Source menu........................................................................................................................................... 36
10.3. Search menu........................................................................................................................................... 36
10.4. Settings menu........................................................................................................................................ 37
10.5. TV menu................................................................................................................................................... 57
10.6. Media browser menu ..........................................................................................................................60
11. HbbTV system ..................................................................................................................... 62
12. MEDION® Life Remote app................................................................................................. 62
13. Data protection MEDION® Smart TV ................................................................................. 64
14. Troubleshooting ................................................................................................................. 65

EN
3
14.1. Do you need more help?.................................................................................................................... 67
14.2. Smart TV pixel faults ............................................................................................................................ 67
15. Cleaning .............................................................................................................................. 68
16. Storing the device when not in use................................................................................... 68
17. Disposal............................................................................................................................... 69
18. Technical specifications ..................................................................................................... 70
19. Product data sheet ............................................................................................................. 72
19.1. Trademark information....................................................................................................................... 72
20. Service information............................................................................................................ 73
21. Legal Notice ........................................................................................................................ 73
22. Privacy statement............................................................................................................... 74
23. Index .................................................................................................................................... 75

4
1. Information about these operating instructions
Thank you for choosing our product. We hope you enjoy using this device.
Read the safety instructions carefully before using the device for the first time. Note the
warnings on the device and in the operating instructions.
Always keep the operating instructions close to hand. If you sell the device or give it away,
please ensure that you also pass on these operating instructions. They are an essential component
of the product.
1.1. Key to symbols
If a block of text is marked with one of the warning symbols listed below, the hazard described in
that text must be avoided to prevent the potential consequences described there from occurring.
DANGER!
Warning: risk of fatal injury!
WARNING!
Warning: risk of possible fatal injury and/or serious irreversible injuries!
CAUTION!
Warning: risk of minor and/or moderate injuries!
NOTICE!
Follow with these instructions to prevent damage to the device!
More detailed information about using the device.
Comply with the notes in the operating instructions.
Due to the 5 GHz frequency range of the wireless LAN solution used, the device may
only be used inside buildings in the EU.
WARNING!
Warning: risk of electric shock!
WARNING!
Warning: danger due to loud volume!
• Bullet point/information on steps when the device is in use
Instruction to be carried out
Declaration of Conformity (see "EU declaration of conformity" section): Products that feature
this symbol meet the requirements of the EC directives.

EN
5
Protection class II
Electrical devices in protection class II are devices that have double and/or reinforced in-
sulation throughout, and do not have the option of connecting a protective earth. The
housing of an electrical device in protection class II, with surrounding insulating material,
may either form all of the additional or reinforced insulation, or part of it.
Symbol for direct current
Symbol for AC current
1.2. Proper use
This is an entertainment electronics device and is also suitable for multimedia applications. This de-
vice is designed to receive and play back television channels. The various connection options enab-
le the additional extension of the reception and playback sources (receiver, DVD player, DVD recor-
der, video recorder, PC etc.). Your device can be used in a variety of ways.
The device is only intended for private use and not for industrial/commercial use.
• Please note that we shall not be liable in cases of improper use.
• Do not modify the device without our express agreement and do not use any accessories that
have not been supplied or approved by us.
• Only use replacement parts or accessories that we have supplied or approved.
• Comply with all the information in these operating instructions, especially the safety information. Any other
use is considered improper and can cause personal injury or property damage.
• Do not use the device in extreme environmental conditions.
• This device is only suitable for use in dry interior rooms.
• This device is not suitable for use as a data monitor for office workstations.
2. Package contents
Please check your purchase to ensure that all the items are included and contact us within 14 days
of purchase if any parts are missing.
The following items are supplied with your product:
• Smart TV
• Remote control (RC1822) incl. 2 x 1.5 V batteries (type LR03/AAA)
• Stands including fastening screws
• Power cord
• Documentation
DANGER!
Risk of suffocation!
Packaging film can be swallowed or used improperly. Therefore, there is a risk of
suffocation!
Keep packaging material such as plastic film or plastic bags away from children.

6
3. Safety information
3.1. Operating safety
– Before using the device for the first time, check the device for damage. A defective or
damaged device may not be operated.
– This device may be used by children over the age of 8 and by persons with limited
physical, sensory or mental abilities or by those without experience and knowledge, if
they are supervised or have been instructed in the safe use of the device and have un-
derstood the dangers that result from it.
– Children must not be allowed to play with the device. Cleaning and maintenance by
purchasers must not be carried out by children unless they are supervised.
DANGER!
Risk of choking and suffocation!
The packaging material is not a toy! Packaging film can be swallowed or used im-
properly, creating a risk of choking and suffocation.
Keep packaging material such as plastic film or plastic bags away from children.
DANGER!
Risk of electric shock!
Risk of electric shock, short circuit and fire!
Never open the housing of the Smart TV and do not push objects inside the
Smart TV through the slots and openings.
WARNING!
Overheating! Risk of fire!
Overheating may result in damage to the Smart TV and the risk of fire!
The slots and openings on the TV set are for ventilation purposes. Do not cover
these openings, for example with newspapers, table cloths, curtains etc.
– Do not subject the display to pressure. There is a risk of the screen glass breaking.
– The remote control has a Class 1 infrared diode. Never use optical equipment to look
at the LED.
CAUTION!
Risk of injury!
Risk of injury due to broken display!
Do not touch the display with fingers or sharp objects to avoid damage.
Use protective gloves when wrapping up cracked parts.
Wash your hands with soap afterwards, as the risk of chemicals escaping cannot be exclu-
ded.
Send the broken parts to your Service Centre for proper disposal.
Disconnect the device from the mains supply immediately and only use it again after it
has been checked by a qualified person or customer services. It is an emergency situation
if, for example, the device produces smoke or unusual noises, water has penetrated the
device, the mains cable or housing is damaged.
Contact customer services if:
– the mains cable is burnt or damaged
– liquid has penetrated the device
– the device is not operating correctly

EN
7
– the device has fallen or its housing is damaged
– The device produces smoke
3.2. Installation location
– The wall mounting of the TV device must not exceed a height of 2 m. The device need
to be mounted on rigid surfaces such as cement or concrete.
– Place the TV set on a sturdy, level surface. Some aggressive varnishes can corrode the
rubber feet on the device.
– When used for the first time, new devices may give off a typical, unavoidable but com-
pletely harmless odour. This will fade over time. We recommend you ventilate the
room regularly to help dissipate this odour.
We have taken appropriate measures during
the development of this product to ensure that levels
are well below legal limits.
– Keep your Smart TV and all connected devices away from moisture and avoid dust,
heat and direct sunlight. Non-compliance with these instructions can cause faults or
damage to the Smart TV.
– Do not use the device outdoors as it could be damaged by weather such as rain, snow
etc.
– The device may not be exposed to water droplets or spray. Do not place any liquid-filled
containers (vases or similar) on or next to the device. Such containers could tip over and
the liquid could impair the electrical safety of the device.
NOTICE!
Risk of damage!
Risk of injury due to candles and other open flames.
Keep candles and other open flames away from this product at all times, to pre-
vent fire from spreading.
– Make sure that there is enough clearance between the device and any surrounding
furniture or walls. Ensure a minimum clearance of 10 cm around the device for suffi-
cient ventilation.
– Avoid glare, reflections and extreme dark-light contrasts to protect your eyes.
– The optimal viewing distance is 3 times the screen diagonal.
DANGER!
Risk of injury! Risk of fatal injury!
Only place the TV set on stable surfaces. Falling televisions may cause serious inju-
ries and even death. Many injuries, particularly for children, can be avoided by ta-
king the following precautions.
Only operate the Smart TV and its components on a sturdy, level and vibrati-
on-free surface to prevent it from falling.
– Only use the TV with the supplied feet and screws.
– Only use furniture that ensures that the TV is positioned safely.
– Take care to ensure that the TV does not protrude over the edges of the furniture.

8
– Do not place the TV on suspended furniture, such as wall cupboards or shelves, wi-
thout safely and securely fixing both the furniture and the TV set. Take care to ensure
that the furniture is mounted correctly and do not exceed its maximum load.
– Do not place any covers or similar beneath the TV to ensure that it is securely positi-
oned.
– Warn children of the dangers of climbing on furniture when trying to reach the TV set
or its controls.
If you store or change your TV, also observe the safety instructions specified above.
3.3. Ambient temperature
– The device can be operated at an ambient temperature of +5 °C to +35 °C and at a re-
lative humidity of 20% to 85% (non-condensing).
– When switched off, the Smart TV can be stored at temperatures of between -20 °C and
+60 °C.
– Keep the device at least one metre away from sources of high-frequency or magnetic
interference (televisions, loudspeakers, mobile telephones, etc.) to avoid malfunctions.
– Remove the plug from the mains outlet and the antenna cable from the antenna so-
cket during a thunderstorm or if the device is not going to be used for a long period.
NOTICE!
Risk of damage!
Major changes in temperature or fluctuations in humidity can cause moisture to
build up within the Smart TV due to condensation – this can cause an electrical
short circuit.
After transporting the Smart TV, wait until it has reached ambient temperature
before switching it on.
3.4. Repairs
– Repairs to your Smart TV should only be carried out by qualified specialists.
– If a repair must be carried out, please contact only our authorised service partners.
– Take care to ensure that only spare parts specified by the manufacturer are used. The
use of unsuitable spare parts can cause damage to the device or the risk of fire.

EN
9
3.5. Safety when connecting
3.5.1. Power supply
– Even when deactivated, some of the device components are live. To disconnect the
power to your Smart TV or to completely isolate the device from voltage sources, dis-
connect the device from the power supply completely. To do so, remove mains plug
from the socket.
DANGER!
Risk of electric shock!
Risk of death due to electric shock when the housing is open.
Do not open the device housing. It does not contain any parts for maintenance
by the user.
– Only operate the Smart TV from an earthed 220 to 240 V~ 50 Hz socket. Contact your
local energy supplier if you have any questions about the power supply at the installa-
tion location.
– The socket must always be easily accessible so that the plug can be quickly removed
from the socket in an emergency.
– To disconnect the power supply from your TV, pull the plug from the socket.
– For additional safety, we recommend using a surge protection device to protect your
Smart TV against damage due to voltage spikes or lightening strike from the power
supply.
– Position the cables so that no one can tread on them or trip over them.
– Do not place any objects on the cables as they may be damaged.
– Never touch the plug with wet hands.
– Always hold the housing and never pull on the cable when removing the plug from
the socket.
– Please note that the TV set continues to use power when in standby mode.
If the device switches off and restarts due to electrical discharge while in USB mode
(media player), optional HbbTV mode or optional LAN/WLAN mode (media player/
portal), it may not be able to independently restore the last operating mode. Please
start the respective media or applications again.
The last user settings entered may not be restored following an electrical discharge
that causes the TV to switch off because these settings are only saved 5 minutes af-
ter switching channels.
All multimedia devices that can be connected to the corresponding connections of
the TV must comply with the requirements of the Low Voltage Directive.

10
3.6. Handling batteries
WARNING!
Risk of explosion!
Batteries may contain combustible materials and leak, heat up excessively, ignite or
even explode.
Avoid improper handling of the batteries to prevent damage to your device and
your health.
Please follow the safety advice below closely:
– Keep batteries away from children.
Consult a doctor immediately if batteries are swallowed.
– Never charge batteries (unless they are designed to be recharged).
– Never discharge batteries by means of high power output.
– Never short-circuit the batteries.
– Never expose the batteries to excessive heat (such as direct sunlight, fire or similar).
– Do not dismantle or deform the batteries.
You could injure your hands or fingers, or battery fluid could get into your eyes or onto
your skin. If you do come into contact with battery fluid, rinse the affected area with
plenty of water and consult a doctor immediately.
– Avoid heavy impacts and vibrations.
– Always observe the correct polarity.
– Take care to ensure that the plus (+) and minus (−) poles are correctly inserted to avoid
short circuits.
– Do not mix up new and old batteries or different types of batteries.
This could cause your remote control to malfunction. In addition, the weaker batteries
would discharge too much.
– Remove used batteries from the device immediately. There is an increased risk of lea-
kage with flat batteries.
– Remove the batteries from the remote control if it is not going to be used for a long
period of time.
– Replace all used batteries in the remote control at the same time with new batteries of
the same type.
– Cover the contacts of the batteries with sticky tape if you want to store or dispose of them.
– If necessary, clean the battery and device contacts before insertion.
– If the batteries have leaked, wear protective gloves and clean the contacts thoroughly.

EN
11
4. EU – Declaration of Conformity
Medion AG hereby declares that this device complies with the required regulations in the EU and
the fundamental requirements and the other relevant provisions of the following:
• Radio Equipment Directive 2014/53/EU
• Ecodesign Directive 2009/125/EC
• RoHS Directive 2011/65/EU
You can download the complete EU Declaration of Conformity at www.medion.com/conformity.
Due to the 5 GHz frequency range of the integrated wireless LAN solution, the device may only be
used inside buildings in the EU (see table).
AT BE BG CZ DK
EE FR DE IS IE
IT EL ES CY LV
LI LT LU HU MT
NL NO PL PT RO
SI SK TR FI SE
CH UK(NI) HR
AT = Austria, BE = Belgium, BG = Bulgaria, CZ = Czech Republic, DK = Denmark, EE = Estonia,
FR = France, DE = Germany, IS = Iceland, IE = Ireland, IT = Italy, EL = Greece, ES = Spain, CY = Cyprus,
LV = Latvia, LI = Liechtenstein, LT = Lithuania, LU = Luxembourg, HU = Hungary, MT = Malta,
NL = Netherlands, NO = Norway, PL = Poland, PT = Portugal, RO = Romania, SI = Slovenia,
SK = Slovakia, TR = Turkey, FI = Finland, SE = Sweden, CH = Switzerland, UK(NI) = Northern Ireland,
HR = Croatia

12
5. Overview of the device
5.1. Front
1
2
1) LCD screen
2) Infrared sensor: Reception field for the infrared TV signals.
Operating light: Lights up when the device is in standby mode.

EN
13
5.2. Rear and right-hand side
14
(ARC)
6
8
9
11
12
SPDIF
Optic. out
10
L
RVideo
BACK AV IN
13 Vdc/18 Vdc
300mA Max.
7
USB
5Vdc
Max. 500mA
1
2
3
4
5
13
1) COMMON INTERFACE (CI+): Card slot for connecting pay TV cards
2) USB (5V , 500 mA max.): USB connection for media playback/recording (PVR)
3) HDMI 1: HDMI connection for devices with a HDMI output
4) : For connecting headphones with 3.5 mm jack
5) : Multifunction button for standby function, switching channels, selecting input source or
controlling volume. When the device is in standby mode, you can switch on the device by
briefly pressing the button. Briefly press the button when the device is in use to open the fun-
ction menu. Then briefly press the button again to select the desired function. Press and hold
the button to open the menu for the selected function. In the case of the standby function,
the device then switches to standby mode. You can change the setting in the menu by briefly
pressing the button. Then press and hold the button to apply the settings made. The function
menu closes automatically after a few seconds of inactivity.
6) HDMI 2-3: HDMI connection for devices with a HDMI output (HDMI 2 can be used for CEC/
ARC)
7) LNB (13 V/18 V , 300 mA max.): For connecting the antenna (satellite)
8) ANT.: For connecting an aerial (analogue, DVB-T or DVB-C)
9) VGA: VGA port for connecting a PC or a YUV adapter (optional)
10) BACK AV IN: Audio/video input (cinch)
11) SPDIF Optic. OUT: Digital audio output (optical)
12) LAN: Network connection to connect to the Internet
13) Mains connection socket

14
14) Fixing holes for a wall mount1
Vesa standard, hole spacing 75 x 75 mm
The wall mounting of the TV device must not exceed a height of 2 m. The device need to
be mounted on rigid surfaces such as cement or concrete.
5.3. Remote control


  
MEDION



 
1

1
21
2
3
4
6
8
9
11
12
13
14
15
17
18
20
7
16
5
19
10
1Wall mount not supplied. When mounting the device, make sure that you use M4 screws. The length of the screws corresponds to the thickness
of the wall bracket plus 7 mm.

EN
15
1) (SOURCE): Select input signal of connected devices
2) Number buttons:
TV: programme selection, teletext: page selection
3) TXT : Activate teletext
Press 2 x = set transparent;
Press 3 x = close
4) P/: Programme selection buttons
TV: select next (+) / previous (−) programme;
teletext: select next (+) / previous (−) page
5) (MENU): Open and close menu
6) INFO: Digital TV: show information (e.g. current channel number)
7) Direction button : Move up in menu
Digital TV: Select info bar for the current programme, teletext: select next page;
Direction button : Move down in menu
Digital TV: Select info bar for the current programme, teletext: select previous page;
Direction button : Move left in menu
Teletext: Call up subpages;
Direction button : Move right in menu
Teletext: Call up subpages
8) EXIT: Exiting the menu
9) MEDION: Open the MEDION® portal
10) PRIME VIDEO: Open the Amazon Prime Video portal
11) Red button: For teletext or menus
Green button: For teletext or menus
Yellow button: For teletext or menus
Blue button: For teletext or menus
12) Media buttons
: Fast rewind;
: Fast forward;
: Start recording (PVR);
: Stop playback;
: Start playback;
: Pause playback
13) 1: YouTube / multifunction button for programme channel or input source
14) NETFLIX: Call up Netflix site
15) BACK: Go one level back in menus; TV: switch to previous program (Swap function)
16) OK: Confirm selection in certain menus
17) EPG: Digital TV: call up the electronic programme guide
18) V/+ : Increase (+) or decrease (−) volume.
19) : Mute
20) LANG.: Analogue TV: stereo/mono;
Digital TV: select audio language (if available)
21) : Switch smart TV on/off (switch standby mode on/off)

16
5.3.1. Programming the multifunction button 1
The 1button can be programmed to any channel position or a particular input source
Start by selecting the function you require and then hold down the button for 5 seconds until
MY BUTTON IS SET appears on the screen. This confirms the new programming.
After each INITIAL INSTALLATION your customised button programming is deleted and re-
set to the factory defaults
6. Using the device for the first time
Before using for the first time, be sure to read the section “Safety instructions”.
6.1. Unpacking
• Select a suitable place for setting up the device before unpacking.
• Open the box very carefully to avoid damaging the device. The device could be damaged if you
use a knife with a long blade to open the box.
• The box contains a number of small items (including batteries). Keep these out of the reach of
children as they represent a choking hazard.
• Store the packaging material in a safe place; only use this box to transport the TV.
DANGER!
Risk of suffocation!
Packaging film can be swallowed or used improperly. Therefore, there is a risk of
suffocation!
Keep packaging material such as plastic film or plastic bags away from children.

EN
17
6.2. Mounting
Attach the stands as shown in the illustration. Carry out this step before connecting the smart TV.
2 x

18
6.3. Inserting batteries in the remote control
Loose the screw of the battery compartment cover on the back of the remote control and remo-
ve the cover.
Insert two LR03 (AAA) 1.5 V batteries in the battery compartment of the remote control. Check
the battery polarity (inscribed on the bottom of the battery compartment).
Close the battery compartment by fixing the cover with the screw.
NOTICE!
Risk of damage!
The remote control can be damaged by leaking batteries if not used for a long pe-
riod of time!
Remove the batteries from the remote control if the device is not going to be
used for a long period.
6.4. Connecting the antenna
Your smart TV supports different antenna signals.
You can feed the following picture signals via the connection labelled ANT.
• via analogue cable/an analogue house antenna,
• via a DVB-T/ DVB-T 22antenna or
• via a DVB-C2connector (digital cable)
Connect the antenna cable from either the house aerial/the analogue cable connection, the
DVB-T antenna or the DVB-C connection to the antenna connection on the smart TV
You also have the option of connecting a digital satellite system to the connection labelled LNB.
Screw the F connector of a coaxial antenna cable onto the connection on the smart TV.
To receive encrypted/subscription channels you will need to use a CI module and
an appropriate card. Insert a CI module (available in specialist shops) into the slot
provided for this purpose on the left-hand side of the device (Common Interface).
You can then insert the card from your provider into the CI module.
6.5. Connecting the power supply
Connect the mains plug on the device to an easily accessible 220 - 240 V ~ 50 Hz mains socket.
6.6. Switching the smart TV on and off
The device will be in standby mode as soon as you have connected the mains plug to the mains
socket.
To switch on the device, press
– on the remote control: the Standby/On button , one of the number buttons or one of the
P/buttons;
– on the device: the multifunction button .
Use the Standby/On button on the remote control to switch the device back into standby
mode. Although the device has been switched off, it will continue to consume electricity.
If the device is not receiving an input signal, it will automatically switch to stand-
by mode after five minutes. A countdown timer will appear on the screen until this
time. This function is not available for all sources.
2This service must be available in your region.

EN
19
6.7. Channel search when switching on for the first time
When settings for various menu items are changed, a message indicating increa-
sed energy consumption may appear.
When you switch the device on for the first time, you will be guided through the FIRST TIME INSTAL
LATION menu.You can call up and carry out the first-time installation again at any time via the menu
INSTALLATION > FIRST TIME INSTALLATION .
OK BACK EXIT HOME
Welcome please select your language!
Set the language used in menus.
12345
Dansk
Français
Magyar
Română
Svenska
Deutsch
Gaeilge
Nederlands
Shqiptar
Türkçe
Eesti
Hrvatski
Norsk
Slovenski
Česky
English
Italiano
Polski
Slovenčina
Укрaїнськa
Español
Latviešu
Português
Srpski
Бблгapски
Crnogorski
Eλληυικά
Lietuvių k.
Pyсский
Suomi
Azәrbaycanca
Use the buttons to select the language and press OK to confirm.
If you wish, you can now set the menu view (HIGH CONTRAST, MAGNIFICATION and MINIMAP) to
your preferred settings
Use the  keys to select the language..
After confirming the selected language with OK the initial installation will begin
OK BACK EXIT HOME
Choose your country
You can configure country settings to activate country specific features.
12345
Hungary
Israel
Luxembourg
Norway
San Marino
Italy
Macedonia
Iran
Kingdom of Sau...
India
Jordan
Malta
Poland
Serbia
Iraq
Latvia
Montenegro
Portugal
Slovakia
Ireland
Lebanon
Netherlands
Romania
Slovenia
Turkey
Isle of Man
Lithuania
New Zealand
Russia
South Africa
Spain Sweden Switzerland Thailand Ukraine
UK Other
Iceland
Use  to select the desired country. The country setting will influence the order in which
the channels are stored. Also, there are a number of options preset for the individual countries.
Afterwards, press OK to continue.
You will be asked to agree to the MEDION® Smart TV Privacy Policy. This is necessary if you intend
to use the Network / Internet / HbbTV services. Read the privacy settings carefully. Select the in-
dividual points with  and confirm them with OK, if necessary. If you have any ques-
tions, complaints or comments regarding this privacy policy or its enforcement, please contact
by email at [e-mail].
Then confirm with YES. If you choose NO, you will not be able to use these services without later
agreeing to the terms.
Finally, press the NEXT button with  and press OK to go to the next point.

20
6.7.1. Network/Internet settings
OK BACK EXIT HOME
Network/Internet Settings
12345
NetworkType
PressWPS on your wifi router
Internet SpeedTest
Advanced Settings
Networked Standby Mode
Wireless Device
On
Next
You can configure network settings to access content on your home network and the internet. Select„Next“ to scan
Disconnected
MAC:
< >
N
etworkT
y
pe
Wireless Device
<>
Wireless Device
wireless networks.
Network settings
NETWORK TYPE
Here you select the network type: WIRELESS DEVICE or WIRED DEVICE. After ma-
king a selection NEXT with the direction buttons  and confirming with
the OK button, an overview of all available networks appears. Make a selecti-
on and confirm with the OK button. If a password is required for a network, a
virtual keyboard appears which you can use to enter this with the help of the
direction buttons  and the OK button. After entering the password,
select OK on the keyboard and confirm with the OK button.
PRESS WPS ON
YOUR WIFI ROU
TER
(only for WLAN)
This option enables you to quickly establish a WPS connection via a wireless
network (Wi-Fi). Hold down the WPS button on your router and confirm this
option OK using the OK button. Then the WPS connection will be made.
INTERNET SPEED
TEST Press the OK button in order to test the Internet speed.
ADVANCED SET
TINGS
Press the OK button to call up further network configuration options.
CONFIGURATION
Choose the setting AUTOMATIC IP or MANUAL IP. If you
select MANUAL IP, three additional lines appear in
which you can manually enter the data for the IP AD
RESS, SUBNET MASK and DEFAULT GATEWAY using the di-
rection buttons  and the number buttons.
CONFIGURATION
Select here between AUTOMATIC DNS or MANUAL DNS.
If you select MANUAL DNS, two additional lines appear
in which you can manually enter the data for the DNS
SERVER 1 and DNS SERVER 2 using the direction buttons
 and the number buttons.
An existing network connection can be terminated by pressing
the red button.