Medion P15109 User manual

N26968
AUS
80 cm (31.5“) Full HD Direct LED LCD TV
MEDION®P15109 (MD 30612)
Instruction Manual
07/2013
MEDION Australia Pty Ltd
St Leonards, NSW 2065
Australia
Hotline: [phone]
Opening hours: Mon - Fri 08:30AM to 06:00PM EST
Internet
www.medion.com.au
E-mail Support
[email protected]
30612 Aldi AUS RC1 Cover.indd 130612 Aldi AUS RC1 Cover.indd 1 15.04.2013 09:23:1115.04.2013 09:23:11

1
Telephone: [phone]
Internet: www.medion.com.au
After Sales Support
80 cm (31.5“) Full HD Direct LED LCD TV
Warranty Details
The product is guaranteed to be free from defects in workmanship and parts for a
period of 12 months from the date of purchase. Defects that occur within this warranty
period, under normal use and care, will be repaired, replaced or refunded at our
discretion. The benefits conferred by this warranty are in addition to all rights and
remedies in respect of the product that the consumer has under the Competition and
Consumer Act 2010 and similar state and territory laws.
Our goods come with guarantees that cannot be excluded under the Australian
Consumer Law. You are entitled to a replacement or refund for a major failure and for
compensation for any other reasonably foreseeable loss or damage. You are also entitled
to have the goods repaired or replaced if the goods fail to be of acceptable quality and
the failure does not amount to a major failure.

2
Telephone: [phone]
Internet: www.medion.com.au
After Sales Support
Device Overview
D-LED LCD TV
Front view
INPUT MENU CH- CH+ VOL- VOL+ POWER
1
234
567
1) Direct LED LCD Display
2) D-LED LCD Mode indicator: Press RQYGT to turn on and off.
Infrared sensor: reception field for the infrared TV signals.
3) RQYGT: Standby on/off
4) XQN"-1XQN - : Adjust the volume or navigate in the menu
5) EJ"-"1EJ"/": Channel up/down or navigate in the menu
6) OGPW: Call up on-screen menu to change settings on your device
7) KPRWV: Change input source

3
Telephone: [phone]
Internet: www.medion.com.au
After Sales Support
Rear view
SPDIF
COAX OUT HDMI1 HDMI2 Y Pb Pr
VGA
audio in VGA RF
Video R in L in HDMI3 USB Headphone out
1
2
3
4
5
67
8
9
310
11
12
5V--- ,500mA max
1) JGCFRJQPG"QWV: Earphone connection
2) WUD"7X "722oC"OCZ: USB connection
3) JFOK"3/5<"HDMI connection: to connect a device with HDMI out
4) CWFKQ"N"T<"Audio inputs (red/white) for AV and Component IN
5) XKFGQ"Video input 1 (yellow)
6) TH: Antenna connection
7) XIC: VGA connection: to connect a PC or Notebook
8) XIC"CWFKQ"KP"*RE"CWFKQ"KP+: Audio input for PC or Notebook
9) [RdRt: to connect to the component (YPbPr) output of a source device (e.g. DVD Player).
10) URFKH"EQCZ"QWV: Digital coaxial output.
11) CE"RQYGT"KP: Connect to the mains supply with the power cable (AC 100-240V~ 50/60Hz)
12) Mounting holes for a wall bracket.
Important!
Wall bracket not included in the delivery. Make sure to use M5 screws for mounting. The length
of the screws results from the thickness of the wall bracket plus 8 mm.

4
Telephone: [phone]
Internet: www.medion.com.au
After Sales Support
Remote control
POWER MUTE
PICTURE ASPECT SOUND
SLEEPSUBTITLE CH.LIST
REC.LISTREC
123
456
789
0
VOL CH
INPUTDISPLAY
EPG
TV/RADIO
FAV
MENU
TV/TXT CANCEL REVEAL NICAM/A2
INDEX HOLD SIZE SUBPAGE
EXIT
1
3
4
5
6
7
8
9
10
11
12
13
14
16
17
1819
20
21
22
23
24
25
26
27
28
29
30
31
32
33
35
36
37
15
2
34

5
Telephone: [phone]
Internet: www.medion.com.au
After Sales Support
1) : Mute
2) CURGEV: Change picture format
3) UQWPF: Choose sound mode
4) EJ0NKUV: Display the programs list.
5) TGE0NKUV: Record list
6) : Return to the previous channel viewed.
7) HCX: Open favourites list.
8) EJ : Channel up/down navigating
9) KPRWV: Select input signal of connected devices.
10)  : Direction buttons.
11) GZKV: Exit menu.
12) [GNNQY"DWVVQP: Short cuts - follow the coloured links in the text.
13) DNWG"DWVVQP: Short cuts - follow the coloured links in the text.
14) PKECO1C4: TV Nicam/A2 select.
15) TGXGCN: Reveal any hidden text.
16) UWDRCIG: Press to enter subpages, press again to cancel.
: Next chapter.
17)
: Stop program.
18) UK\G: Press to see top half of page double size, press again to see the bottom half of page double
size. Press again for normal size.
: Previous chapter.
19) JQNF: No function.
: Fast forward.
20) : Pause/play program.
21) KPFGZ: Go to index.
: Fast reverse.
22) ECPEGN: No function.
23) VX1VZV: Switch between TV and radio stations.
24) TGF"DWVVQP: Short cuts - follow the coloured links in the text.
25) ITGGP"DWVVQP: Short cuts - follow the coloured links in the text.
26) OGPW: Open and close menu.
27) QM: Confirm selection in specific menus. Also used as ENTER.
28) FKURNC[: Press to display the current mode’s information.
29) VX1TCFKQ: Change from TV to radio programs.
30) XQN"-1/: Increase (+) or reduce (-) volume.
31) GRI: To show the Electronic Program Guide during no-menu state only in DTV mode.
32) PWOGTKE"DWVVQPU: Channel selection.
33) : Press to start record the program in DTV mode.
34) UNGGR: Sleep timer.
35) UWDVKVNG: Turn on/off the subtitle display in DTV mode.
36) RKEVWTG: Choose picture mode.
37) <"STANDBY, i.e. switch off the LED LCD TV temporarily.

6
Telephone: [phone]
Internet: www.medion.com.au
After Sales Support
Table of Contents
Warranty Details..................................................................................................................... 1
Device Overview ..................................................................................................................... 2
D-LED LCD TV........................................................................................................................................2
About these Instructions ........................................................................................................ 8
Target Group .........................................................................................................................................8
Full HD...................................................................................................................................................8
Contents................................................................................................................................................8
Safety Instructions.................................................................................................................. 9
Operating Safety .................................................................................................................................... 9
Set-Up Location .....................................................................................................................................9
Repairs................................................................................................................................................. 10
Intended Environment ......................................................................................................................... 10
Power Supply....................................................................................................................................... 10
Battery Handling.................................................................................................................................. 10
Information about Conformity ............................................................................................................. 11
Start of Operation ................................................................................................................................ 11
Unpacking ........................................................................................................................................... 11
Installation........................................................................................................................................... 11
Inserting the Batteries in the Remote Control ....................................................................................... 12
Connect TV aerial................................................................................................................................. 12
DVB-T Mode (Standard Definition and High Definition)........................................................................ 12
Connecting a DVB-T aerial ................................................................................................................... 12
Connecting Power Supply ................................................................................................................... 12
Switching the D-LED LCD TV on and off............................................................................................... 12
After Switching on the Unit for the First Time....................................................................................... 13
Channel Selection................................................................................................................................ 13
Setting the Volume .............................................................................................................................. 13
Picture Setting...................................................................................................................................... 14
Displaying Information ........................................................................................................................ 14
Favourites List ...................................................................................................................................... 14
Input Source Selection ......................................................................................................................... 14
Media Mode .......................................................................................................................... 15
Media Mode and USB Connectivity...................................................................................................... 15
Recording via Record Button (PVR or Red Button) ................................................................................15
Switching between TV Mode and Media Mode.................................................................................... 16
Media Menu System ............................................................................................................................ 16
Basic OSD Menu Settings....................................................................................................... 17
Navigating within the Menu ................................................................................................................ 17
Tuning the Video Recorder (VCR) Manually.......................................................................................... 19
EPG - Program Guide ............................................................................................................23
Connecting External Devices................................................................................................. 24
Connecting Headphones ..................................................................................................................... 24
Digital Amplifier via Coaxial Connection .............................................................................................. 24
2. Component Video Cable (3 x Cinch/RCA)........................................................................................ 24
3. HDMI Cable ..................................................................................................................................... 24
Connecting a Video Recorder (VCR) ..................................................................................................... 24
Connecting a DVD Recorder ................................................................................................................ 24
Connecting a Set Top Box (SAT, SD/HD DVB-T, Decoder, Etc.) ............................................................. 25
1. Stereo Cinch/RCA Cable and a Video Cinch/RCA Cable ....................................................................25
2. Component Video Cable (3 x Cinch/RCA)........................................................................................25
3. HDMI Cable .....................................................................................................................................25

7
Telephone: [phone]
Internet: www.medion.com.au
After Sales Support
Connecting a Camcorder.....................................................................................................................25
Device with HDMI or DVI Output.........................................................................................................25
Connecting an External Device with HDMI Output ..............................................................................25
Connecting an External Device with DVI Output..................................................................................25
Connecting a PC or Notebook..............................................................................................................26
Troubleshooting ................................................................................................................... 27
Do You Need More Help?.....................................................................................................................28
D-LED LCD TV pixel faults...................................................................................................... 29
Cleaning ............................................................................................................................... 30
Disposal ................................................................................................................................ 30
Technical Data ...................................................................................................................... 31

8
Telephone: [phone]
Internet: www.medion.com.au
After Sales Support
About these Instructions
Before using the device for the first time, you should read these operating instructions
thoroughly and follow the safety advice. This device may only be used as described in the
operating instructions.
Always keep these operating instructions at hand but store them safely so that you can pass them
on to a new owner should you sell the unit.
Target Group
• This unit is to be used only for receiving and playing back TV programmes. The range of connections
supplied makes it possible to expand the input and output sources (e.g. receiver, DVD player, DVD
recorder, video recorder, PC, etc.).
• This unit is intended for use in dry, indoor areas only.
• It is not suitable for use as a data monitor for office workstations.
• The unit is intended for private use only and not for industrial or commercial use. Using the device in
extreme environmental conditions may result in it being damaged.
Full HD
Your D-LED LCD TV is equipped with the feature “Full HD”. This means that it is capable of
displaying high-resolution television programmes (HDTV). The prerequisite for this is a HDTV
signal.
Contents
Please check the items received in the box and inform us within 7 days from purchase if anything is
missing. Your statutory rights are not affected.
You should receive the following items:
• 80cm (31.5”) Full HD Direct LED LCD TV
• Remote Control incl. Batteries (2 x R03/AAA/1.5V)
• Stand (including 4 screws)
• Stand Adapter
• Instruction Manual
• 1 x Warranty Certificate
• 2 x Warranty Sticker

9
Telephone: [phone]
Internet: www.medion.com.au
After Sales Support
Safety Instructions
Operating Safety
• Children should be supervised to ensure they do not play with this unit. This unit is not intended for use
by people (including children) with reduced physical, sensory or mental abilities or for those without
experience and/or knowledge, unless they are supervised by a person responsible for their safety or they
have been instructed on its use.
• Keep packaging material such as plastic film away from children. There is a risk of suffocation if used
improperly.
• Never open the housing of the D-LED LCD TV (electrical shock, short circuit and fire hazard)!
• Never insert any objects through the slots and openings of the Direct LED LCD TV (electrical shock,
short circuit and fire hazard)!
• The slots and openings on the D-LED LCD TV are for ventilation purposes. Do not cover these openings
(overheating, fire risk)!
• Do not put any pressure on the display. There is a risk that the screen may break.
• The remote control has a class 1M infrared diode. Never use optical devices to look at the LED.
• Caution! There is a risk of injury if the screen is damaged! Recover all broken pieces using protective
gloves and send them to your Service Centre for proper waste disposal. Then wash your hands with
soap because chemicals may have leaked out.
• To avoid damaging the screen do not touch it with fingers or sharp objects.
• Contact customer services on 1300 884 987 if:
− the power cable is burnt or damaged
− liquid has penetrated the device
− the device is not operating correctly
− the device has fallen, or the casing is damaged
Set-Up Location
• In the first hours of operation, new devices may emit a typical, unavoidable but completely harmless
smell, which will decline increasingly in the course of time. We recommend that you ventilate the room
regularly, in order to counteract the formation of the smell.
• Keep your D-LED LCD TV and all connected devices away from moisture and avoid dust, heat and direct
sunlight.
• Do not use the device outdoors because other effects such as rain, snow etc. can also damage the
device.
• The device must not be exposed to water droplets or spray. Do not place objects that are filled with
water (such as vases) on the device. The container may tip over and the liquid will impair the electrical
safety.
• Do not operate the device near water and do not set it up near a wash-hand basin or bath, etc.
• Do not place any exposed sources of ignition (candles or similar) on or near the device.
• Make sure that there is enough clearance in the wall units! Ensure a minimum separation of 10 cm
around the device for sufficient ventilation.
• Operate all components on a stable, level and vibration-free base, to prevent the D-LED LCD TV from
falling over.
• Avoid dazzle, reflections and strong bright-dark contrast in order to protect your eyes.
• The optimal viewing distance is 5 times the screen diagonal.

10
Telephone: [phone]
Internet: www.medion.com.au
After Sales Support
Repairs
• Repairs to your Direct LED LCD TV should only be carried out by qualified specialists.
• Please contact the MEDION Help Desk at 1300 884 987 if you have any problems with your Direct LED
LCD TV. ALWAYS have repairs completed only by our authorised service centre.
• Make sure to use only replacement parts provided by the manufacturer. The device may sustain damage
if unsuitable replacement parts are used.
Intended Environment
• The device can be operated at an ambient temperature of +5° C to +40° C and a relative humidity of
20% - 85% (non condensing).
• In the switched-off state the Direct LED LCD TV can be stored from -20° C to +60° C.
• Keep the device at a distance of at least one metre from high frequencies and magnetic sources of
interference (television, loudspeaker boxes, mobile telephones etc.) to avoid malfunctioning.
• After transporting the Direct LED LCD TV wait until the device has reached ambient temperature before
switching it on.
• Large changes in temperature or fluctuations in humidity can cause moisture to build up due to
condensation within the Direct LED LCD TV, which can cause an electrical short circuit.
• During thunderstorms or if the device is not going to be used for long periods, remove the plug from
the mains socket and the aerial cable from the aerial socket.
Power Supply
Please note
Even when the mains switch is off some components of the device are live. In order to
disconnect the power to your Direct LED LCD TV or to completely isolate the device from
voltage sources remove the mains plug from the mains socket.
• Only plug the Direct LED LCD TV into an earthed socket with 100-240 V~ 50/60 Hz. Contact you
electricity provider if you are not sure if the socket is earthed or not.
• The socket must be near the Direct LED LCD TV and easily accessible.
• In order to disconnect the power to your Direct LED LCD TV or to completely isolate the device from
voltage sources remove the mains plug from the mains socket. Always grab the plug firmly when
unplugging it from the socket. Never pull on the lead.
• For extra safety, we recommend using an over-voltage protection device to prevent your Direct LED LCD
TV sustaining damage as a result of power surges or lightning strikes.
• If you are using an extension cable, make sure that it complies with Australian safety requirements. If in
doubt, contact your electrician.
• Position the cable so that nobody is able to step on it or trip over it.
• Do not place any objects on the cable to avoid damaging it.
Battery Handling
Batteries can contain combustible materials. If not handled correctly batteries can leak, become very hot,
ignite or even explode, which could damage your device or/and your health.
Please ensure compliance with the following advice:
• Keep batteries away from children. Contact your doctor immediately if a battery is swallowed.
• Never charge batteries (unless it is clearly indicated).
• Never discharge batteries by high power output.
• Never short-circuit the batteries.
• Never expose the batteries to excessive heat such as sunshine, fire or similar.
• Do take apart or deform the batteries. Your hands or fingers could get injured or battery fluids could get
into your eyes or onto your skin. If this should happen then rinse the affected areas immediately with a
large amount of clean water and contact your doctor immediately.
• Avoid heavy impacts and vibrations.
• Always observe the correct polarity.
• Make sure that the plus (+) and minus (-) poles are correctly inserted in order to avoid short circuits.

11
Telephone: [phone]
Internet: www.medion.com.au
After Sales Support
• Never mix new and old batteries or different types of batteries. This could cause your device to
malfunction. In addition, the weaker batteries would discharge too much.
• Immediately remove used batteries from the device.
• Remove the batteries from the device if you do not intend to use it for a long period of time.
• Replace all the old batteries in a device with new batteries of the same type.
• Isolate the contacts of the batteries with sticky tape if you want to store or dispose of them.
• Clean the contacts on the battery and device before inserting.
Information about Conformity
The device fulfils electromagnetic compatibility and electricity safety requirements.
Your device complies with the basic requirements and the relevant Australian EMC guidelines
[electromagnetic compatibility] and the Australian electrical safety guidelines.
This device fulfils the basic requirements and the relevant regulation of the Ecodesign Guideline 2009/125/
EG (Commission Regulation 1275/2008).
Start of Operation
Note
Before starting up please make sure that you read the “Safety instructions”section
Unpacking
• Select a suitable place for setting up the device.
• Open the box very carefully to avoid damaging the device. The device could be damaged if you use a
knife with a long blade to open the box.
• The box contains a number of small items (including batteries). Keep these items out of reach of
children; the parts are easy to swallow.
• Store the packaging material in a safe place; only use this box to transport the TV.
CAUTION!
Do not let children play with the plastic film. There is a risk of suffocation!
Installation
Attach the base stand as shown in the drawing. Carry out this step before connecting the D-LED LCD TV.

12
Telephone: [phone]
Internet: www.medion.com.au
After Sales Support
When using the wall mount brackets (not included) to mount the D-LED
LCD TV on a wall, please remove the stand and its adapter from the
bottom of the TV by loosening the four screws.
Now insert the included cover which covers the hole left by the stand.
Please fix it in place with the four screws. This cover assures that no dust
or objects will get inside the D-LED LCD TV and cause any damage.
Inserting the Batteries in the Remote Control
Open the battery compartment cover on the back of the remote control.
Insert two (AAA) 1.5-V batteries in the battery compartment of the remote control. Check the battery
polarity (inscribed on the bottom of the battery compartment).
Replace the cover.
Note
Remove the batteries if the device will not be used for long periods. The remote control can be damaged by
leaking batteries.
Connect TV aerial
To connect to the house antenna or cable system, connect a double-screened cable from the antenna
socket to the D-LED LCD TV.
DVB-T Mode (Standard Definition and High Definition)
You will have the possibility of receiving DVB-T by means of a corresponding aerial, if it is offered at your
location. An additional receiver will not be necessary to receive DVB-T channels.
Connecting a DVB-T aerial
Plug the connector of a DVB-T aerial into the aerial socket of the device.
Connecting Power Supply
Plug the power cable of the device into a 100 - 240 V - 50 Hz mains socket.
Switching the D-LED LCD TV on and off
Connect to the power supply with a power cord. The unit will switch to standby off mode when
connected to the mains.
To switch on the unit either press the button on the remote control or the RQYGT button of the
unit.
Press the button on the remote control or the RQYGT button of the unit to switch the device over
to standby mode again. The unit continues to consume power in this mode.
Disconnect the power cord from the mains to switch it off completely.

13
Telephone: [phone]
Internet: www.medion.com.au
After Sales Support
After Switching on the Unit for the First Time
You will be guided through the FIRST TIME INSTALLATION menu after you switch the device on for the
first time.
You can always access the first-time installation screen again via SETUP > FIRST TIME INSTALLATION
and go through the settings again.
Select a language with the directional buttons and press QM.
Select the country required with the directional buttons. The country setting will have an influence on
the sequence in which the channels are stored. Press QM.
Searching occurs in the order of the various program types. Wait for it to finish. You can use the OGPW
button to cancel the search prematurely.
Note
Consider a DVB-T aerial if you are searching for digital channels.
Channel Selection
• To select a channel, either press the buttons EJ/(on the device or on the remote control) or select
the channel directly by pressing the appropriate numbers.
To enter a two or three-digit number press the EJ/- button twice or three times and then enter the
two- or three-digit channel number.
• Press the button to select the last channel played.
Setting the Volume
You can increase or decrease the volume by pressing the volume buttons on the remote control
or on the device.
Use the button to switch the volume fully off and on again.
Use the UQWPF button to switch between the following sound modes: STANDARD, MUSIC,
MOVIE, SPORTS, PERSONAL. The Personal setting is defined under the menu option SOUND >
SOUND MODE.

14
Telephone: [phone]
Internet: www.medion.com.au
After Sales Support
Picture Setting
Use the RKEVWTG button to switch between the following picture modes: STANDARD, DYNAMIC,
MILD, PERSONAL. The PERSONAL setting is defined under the menu option PICTURE > PICTURE
MODE.
Depending on the program, the pictures are displayed in the formats 4:3 or 16:9. Use the CURGEV
button to adjust the picture format:
:
AUTO: The format displayed is automatically adjusted to match the input signal.
4:3: For undistorted screen display in 4:3 format.
16:9: A 16:9 picture (“letterbox“) is zoomed to the full screen size.
ZOOM1: For undistorted screen display in 14:9 format.
ZOOM2: A picture in 14:9 format (“letterbox“) is stretched at the top and
bottom margins of the screen.
You can also change these settings in SETUP > ASPECT RATIO
Note:
Please note that not all picture formats will be available depending on the image source setting.
Displaying Information
Press the FKURNC[ button to display the following current settings:
− Channel position
− Color System
− Sound System
You can get the same information when you switch over to a different channel.
Favourites List
You can enter a list of your favourite channels under the menu options CHANNEL > PROGRAMME
EDIT.
Press HCX to display your list of favourite channels.
Use the direction buttons  to select a channel.
Input Source Selection
Use KPRWV to call up the source selection list. The following sources are available:
ATV TV mode (analogue signal)
DTV TV mode (digital signal)
MEDIA Playback of media via USB
AV Device on AV input
PC Device on PC input
COMPONENT Device on the video and audio input components
HDMI1 Device on HDMI 1 input
HDMI2 Device on HDMI 2 input
HDMI3 Device on HDMI 3 input
Use the direction arrows  to go to the desired source.
Confirm your selection with QM.

15
Telephone: [phone]
Internet: www.medion.com.au
After Sales Support
Media Mode
The D-LED LCD TV comes with 1 USB port (rear) that can be accessed via Media mode.
Media Mode and USB Connectivity
Plug in your external USB device (USB stick, external hard disk drive) into the USB port of the TV. Drive
numbers (C:\, D:\, E:\ etc) will be allocated depending on the partitions of the USB device (e.g. an
external hard disk drive might have several partitions). For the definition of how drive numbers are
assigned, please see “Drive Assignment Definition” below. (Please note that external USB memory
devices of a capacity of up to 1 TB are supported. However, not all brands and drivers of external USB
memory devices might be compatible with this D-LED LCD TV)
You can select the drive for your recording session.
Please note that the external USB device needs to be formatted first before the recording can be done.
To do this, under DTV mode, in the OSD, go to SETUP page then select “PVR FILE SYSTEM”.
Select disk drive by pressing “QM”.
At the next screen you will have option to select USB device if there is more then one and to select drive
with directional pad on the remote control (C:\, D:\ etc)
Press “QM” to format.
You can select to format the USB device into FAT32 file system or High Speed FS system by using
directional pad on the remote control:
− FAT32 is suitable for USB thumb drive (USB memory sticks) that will format the entire USB drive
completely. (Attention: All data currently on the USB memory stick will be lost. Please save your data
on your external USB memory stick prior to using it as a recording device)
− High Speed FS is suitable for external USB hard disk drives that will allow choosing how large a new
partition allocated for recording will be.
− While recording, on your external USB device a new folder will be created labelled “MSTPVR”.
The OSD will show the file format and size selected, how many minutes of the TV program can be
recorded in either SD quality or HD quality from the source media.
After selecting the system type and size, press OK again will start the formatting.
After the USB device has been formatted, it can be used for recording under DTV mode.
The default recording drives will always be C:\, unless different drive is selected using method from 2-7.
(Please also refer to the part “PVR Function and Drive Assignment” of this manual).
The recording function can be achieved in 2 ways:
− Press the TGEQTF button (PVR = TGF"EQNQWT"DWVVQP) directly while watching DTV
programs.
− Through GRI scheduling function.
Recording via Record Button (PVR or Red Button)
While watching DTV programs, press the RXT button (TGF"DWVVQP) on the remote control.
A symbol for recording will be shown in the upper left-hand corner of your screen.
Make sure that the allocated capacity for the recording is sufficient to complete the recording of the
program you want to save. (The capacity is determined by how large the formatted PVR file folder is
allocated, or how large the USB thumb drive can support.)
Recording via EPG Scheduling
In DTV mode, press GRI button to call out the EPG interface.
Select the program that you wish to record via the date and time inside the EPG, and then press the
TGF"DWVVQP"*TGEQTF+.
The interface will show the start time and end time of the recording.
Select the recording mode. The options are:
− AUTO Mode: The time will be fixed according to the selected program. Only the selected program
will be recorded from start time to end time.
− ONCE Mode: Allows setting the timer. Date and time of the recording can be set manually. The
recording will be done only once.

16
Telephone: [phone]
Internet: www.medion.com.au
After Sales Support
− EVERY DAY Mode: Allow setting the timer yourself. Date and time of the recording can be set
manually. The recording will be repeated every day accordingly during the set time frame.
− WEEKLY Mode: Allow setting the time. Date and time of the recording can be set manually. The
recording will be repeated once every week on the day and time that has been set manually.
Press QM after the setting to save the scheduling time
Please note that recording schedule via the EPG interface will only work when the TV is not switched off
(has to be on or in standby mode).
The recording schedule will continue to work in the background in Standby mode.
The TV will switch from Standby mode to operational mode (ON) to start the programmed EPG
scheduled recording session.
After the recording has been completed the TV will stay in operational mode (ON).
If you want the TV to switch back to Standby mode after the recording has been completed (switching
back from ON to Standby) please use the “AUTO STANDBY” function in the TIME OSD menu to set
the “Auto Standby” time (starting from 3 hours).
Using the “AUTO STANDBY” function will ensure that the TV will switch back from operational mode
(ON) to Standby mode according to the set time.
Please ensure that the time set via the “AUTO STANDBY” timer is longer than the time set for the
recording session to allow that your program has been fully recorded.
The scheduled recording can be checked via the EPG interface any time. For this, please press the
[GNNQY"DWVVQP (schedule button) on the remote control.
Time Shift Function
During any recording, you can press the “RNC[” button to start watching the program that is being
recorded. The recording itself will continue in the background while you can watch the recorded
program from the start.
While watching/playing the recording program this way, you can use all the media functions (fast
forward, fast backward and pause etc) for the playback.
Press the UVQR button to stop the watching session and return to the recording interface.
Switching between TV Mode and Media Mode
Use KPRWV to call up the source selection list.
Use the direction buttons  to go to Media.
Confirm your selection by pressing QM.
Repeat this process to return to TV mode but, instead of selecting Media, choose the option ATV or
DTV, depending on the type of signal.
Media Menu System
As soon as you have connected an external USB device to the TV and have switched the source to Media,
you can choose between the following four media to be played back:
• PHOTO - To play back photo files
• MUSIC - To play back music files
• MOVIE - To play back movie files
• TEXT - To display texts (*.txt)
Depending on the selected option you will have various available functions. These will be shown in the
lower part of the screen.

17
Telephone: [phone]
Internet: www.medion.com.au
After Sales Support
Basic OSD Menu Settings
You can customise certain functions of the OSD (On-Screen Display) menu.
Navigating within the Menu
Press the OGPW button to activate the OSD.
The available options are displayed on the lower edge of the screen.
You can use the direction keys  to select the options from the main menu.
Use to switch over to the menu entries.
You can use the direction keys  to select the options from any of the menus.
Press OGPW to return to the main menu.
Use the direction button to access a sub-menu (not every menu has a sub-menu option).
Press OGPW to return to the next-higher menu.
Use the direction buttons  to enter a desired value or make another selection.
Press OGPW to close the menu and also confirm your selection.
Please remember that the menu will close automatically after a couple of seconds if you don’t press a
button.
You can select the following main menus:
• Menu CHANNEL
• Menu PICTURE
• Menu SOUND
• Menu TIME
• Menu LOCK
• Menu SETUP
Note
Technical changes to the device means the menus described here may differ from the menus actually displayed
on the screen.
Not all menus will be available, depending on the source you have selected. Switch to a different source to
access all available menus.

18
Telephone: [phone]
Internet: www.medion.com.au
After Sales Support
CHANNEL Menu
CHANNEL
Auto Tuning
ATV Manual Tuning
DTV Manual Tuning
Programme Edit
Signal Information
Move Return Select Exit
0(18 2. (;,7
Menu item Setting
AUTO TUNING Perform the search here.
ATV MANUAL TUNING You can program individual channels in ATV mode manually here.
CURRENT CH Use this to select the channel you would like to address.
COLOUR
SYSTEM
PAL, SECAM, AUTO. For Australia, the colour system is
set to PAL.
SOUND
SYSTEM
BG, DK, L, I. For Australia, the sound system is set to BG.
FINE-TUNE Press  to carry out the fine adjustment.
AFC Set the automatic fine adjustment to On if this is your
continuous choice.
SEARCH Start the channel search with 
DTV MANUAL TUNING You can program individual channels in DTV mode manually here.
PROGRAMME EDIT You will see the currently saved channel here. Each channel can be
customised as follows:
DELETE
Select the program you would like to delete and press the TGF button on
the remote control.
Press the YES key if you are sure that you wish to reset the transmitter.
Press the NO key if you wish to stop the process.
RENAME (only available for ATV)
Select the transmitter that you wish to rename and press the ITGGP key.
Now, you will be able to change the first letter; you will be able to scroll up
and down through the letters with the  direction keys.
Move to the next drive letter with direction key, etc.
Press the ITGGP key again at the end to save the name.
MOVE (Available only in ATV mode)
Select the program and press the [GNNQY button. Move the channel with
 to the desired position and press the [GNNQY button again. The
other channels will be rearranged accordingly.
SKIP
Select the channel you would like to skip while scrolling through the
channels using the buttons CH/and then press the DNWG button.
You can still select this channel by using the number buttons.
FAV
To save a station to a favourites list, highlight it and press the button HCX.
Call up the favourites list by using the remote control buttons.
SIGNAL
INFORMATION
The signal information of the set station is displayed here.
This option is only available in the DTV mode.

19
Telephone: [phone]
Internet: www.medion.com.au
After Sales Support
Tuning the Video Recorder (VCR) Manually
You can use ATV Manual Tuning, for example, to tune a video recorder (VCR) to the Direct LED LCD TV.
Connect the TV and the video reorder via the antenna cable and set the video recorder to the test signal.
Perform a manual channel search with the Direct LED LCD TV.
PICTURE Menu
PICTURE
Picture Mode Personal
Contrast 50
Brightness 50
Colour 50
Tint 50
Sharpness 50
Colour Temp Normal
Noise Reduction Middle
Dynamic CR Off
Move Return Select Exit
0(18 2. (;,7
Menu item Setting
PICTURE
MODE
Select picture mode: STANDARD, MILD, PERSONAL, DYNAMIC. This function
corresponds to the RKEVWTG button.
The Personal setting lets you set the CONTRAST, BRIGHTNESS, COLOUR, TINT
and SHARPNESS yourself. The other parameters are defined.
CONTRAST Increase or decrease contrast (on a scale of 0 – 100).
BRIGHTNESS Increase or decrease brightness (on a scale of 0 – 100).
COLOUR Increase or decrease colour (on a scale of 0 – 100).
TINT Hue settings only available for NTSC reception.
SHARPNESS Increase or decrease sharpness (on a scale of 0 – 10).
COLOUR
TEMPERATURE
Select colour temperature: COLD, NORMAL and WARM.
NOISE
REDUCTION
This function reduces picture noise and improves image quality when the signal is
weak. Choose between OFF, LOW, MIDDLE, HIGH and DEFAULT.
DYNAMIC CR Switch the dynamic contrast ON or OFF.