Meicheng EX-G013A / EX-G013BEX-G015 User manual

EX-G013A / EX-G013B
EX-G015/EX-G017B / EX-G016
EX-G076A / EX-G076B
HDMI over Single CAT5 Distribution Series
User Manual
EX-G016
EX-G017A/ EX-G017B / EX-G015
EX-G013A EX-G013B
EX-G076A EX-G076B
Page 1 of 23

Safety and Notice
The HDMI over Single CAT5 Distribution Series, including
EX-G013A 1x2 HDMI over Single CAT5 Distribution Amplifier,
EX-G017A 1x9 HDMI over Single CAT5 Distribution Amplifier,
EX-G017B 1x9 HDMI over Single CAT5 Distribution Amplifier with 7.1ch audio,
EX-G015 2x8 HDMI 1.3 over Single CAT5 Matrix Switch,
EX-G013B 1x2 HDMI over Single CAT5 Cascading Distribution Amplifier,
EX-G016 2x8 HDMI 1.3 over Single CAT5 Cascading Distribution Amplifier,
EX-G076A HDMI over Single CAT5 Receiver, and
EX-G076B HDMI over Single CAT5 Mini-Receiver
has been tested for conformance to safety regulations and requirements, and has been certified
for international use. However, like all electronic equipments, the HDMI over CAT5 Distribution Series
should be used with care. Please read and follow the safety instructions to protect yourself from
possible injury and to minimize the risk of damage to the unit.
zFollow all instructions and warnings marked on this unit.
zDo not attempt to service this unit yourself, except where explained in this manual.
zProvide proper ventilation and air circulation and do not use near water.
zKeep objects that might damage the device and assure that the placement of this unit is on a
stable surface.
zUse only the power adapter and power cords and connection cables designed for this unit.
zDo not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device
before cleaning.
Page 2of 23

Introduction
The HDMI over Single CAT5 Distribution Series provides the most flexible solution by which the
high definition video and high quality audio can be transmitted to different locations over a long
distance. The devices are cascadable, allowing you to extend HDMI/DVI compliant displays almost
anywhere.
Diagram 1
EX-G076A
EX-G013A
HDTV Speaker
HDMI cable
Speaker Audio cable
HDMI cable
Speaker Audio cable
CAT5 cable
HDMI
cable EX-G076B
CAT5 cable
Audio cable
CAT5 cable
HDMI cable
CAT5 cable
HDMI source
HDTV
EX-G013B
HDTV
EX-G013B
HDTV
EX-G076B
Page 3of 23

Diagram 2
EX-G076A
CAT5e cable up to 25m (80ft)
up to 60m (200ft)
EX-G017A/
EX-G017B
HDTV#1
EX-G076B EX-G076B
HDTV#2
HDMI cable
CAT5e cable
HDMI cable
CAT5e cable
EX-G076A
HDTV#5
HDMI cable
HDTV#6
HDMI cable
EX-G076A
EX-G076A
HDTV#8
EX-G076B
HDTV#7
EX-G076B
CAT5e cable
HDMI cable
HDTV#4
HDTV#3
HDMI cable
HDMI source
Page 4of 23
CAT5e cable

Features
zState-of-the-art Silicon Image (founder of HDMI) chipset embedded for upmost compatibility and
reliability
zHDMI 1.2a compliant (EX-G015 & EX-G016 are HDMI 1.3c compliant)
zHDCP compliant
zRegenerates the HDMI signal
zSupports audio output
zSupports default HDMI EDID and has the ability to learn the EDID of displays
zExtends up to 15m (50ft) of input HDMI cable
zExtends up to 15m (50ft) of output HDMI cable
zExtends up to 60m (200ft) (720p / 1080i) of output CAT5 cable
zExtends up to 40m (130ft) (1080p) of output CAT5 cable
zMinimize the cable skew by adjustable 8-level equalization control [EX-G015/EX-G017) / EX-G013B /
EX-G016]
zPure unaltered uncompressed 7.1ch digital HDMI over LAN cable transmission
zAllows
cascading
zPerfectly integrated with other HDMI over CAT5 series products
z1U rack mountable [EX-G017A / EX-G015 / EX-G017B / EX-G016]; wall mountable [EX-G013A /
EX-G013B]
The length depends on the characteristics and quality of the cables. Higher resolutions and
longer transmission distances require low skew cables (<25ns/100m) for best performance.
Unshielded CAT6 with metal RJ-45 connectors is recommended.
Page 5of 23

Technical Specifications and Package Content
Model Name EX-G013A EX-G013B
Technical
1x2 distribution amplifier
Role of usage Transmitter [TX] Transceiver [TRX]
HDMI compliance HDMI 1.2a
HDCP compliance Yes
Video bandwidth Single-link 165MHz [4.95Gbps]
Video support 480i / 480p / 720p / 1080i / 1080p60
HDMI over LAN cable
transmission range
Full HD (1080p)-40m (130ft) [CAT5e] / 50m (165ft) [CAT6]
HD (720p/1080i)-50m (165ft) [CAT5e] / 60m (200ft) [CAT6]
Audio support Surround sound (up to 7.1ch) or stereo digital audio
Equalization None 8-level digital control
Input TMDS signal 1.2 Volts [peak-to-peak]
Input DDC signal 5 Volts [peak-to-peak, TTL]
ESD protection
[1] Human body model — ±15kV [air-gap discharge] & ±8kV [contact
discharge]
[2] Core chipset — ±8kV
PCB stack-up 4-layer board [impedance control — differential 100Ω; single 50Ω]
Input 1x HDMI 1x RJ-45
Output
1x HDMI
1x RJ-45
1x 3.5mm audio socket
1x HDMI
1x RJ-45
1x 3.5mm audio socket
HDMI connector Type A [19-pin female]
RJ-45 connector WE/SS 8P8C with 2 LED indicators
3.5mm connector Earphone jack for stereo audio
DIP switch 2-pin for EDID/audio mode None
Mechanical
Housing Metal case
Model 180 x 108 x 27mm [7”x4.3”x1.1”]
Package 330 x 200 x 95mm [1’1”x7.9”x3.7”]
Dimensions
[L x W x H] Carton 495 x 440 x 380mm [1’7.5”x1’5.3”x1’3”]
Model 430g [15.2oz] 430g [15.2oz]
Weight Package
Fixedness Wall-mounting case
Power supply 5V 4A DC
Power consumption 3 Watts [max]
Operation temperature 0~40°C [32~104°F]
Storage temperature -20~60°C [-4~140°F]
Relative humidity 20~90% RH [no condensation]
Package Contents 1x EX-G013A or EX-G013B
1x 5V power adapter
1x User Manual
Page 6of 23

Model Name EX-G017A / EX-G017B EX-G015 EX-G016
Technical
1x9 distribution amplifier 2x8 matrix switch
Role of usage Transmitter [TX] Transceiver [TRX]
HDMI compliance HDMI 1.2a HDMI 1.3c
HDCP compliance Yes
Video bandwidth Single-link 165MHz
[4.95Gbps] Single-link 340MHz [10.2Gbps]
Video support 480i / 480p / 720p / 1080i / 1080p60
HDMI over LAN cable
transmission range
Full HD (1080p)-40m (130ft) [CAT5e] / 50m (165ft) [CAT6]
HD (720p/1080i)-50m (165ft) [CAT5e] / 60m (200ft) [CAT6]
Audio support Surround sound (up to 7.1ch) or stereo digital audio
Equalization None 8-level digital rotary control
Input TMDS signal 1.2 Volts [peak-to-peak]
Input DDC signal 5 Volts [peak-to-peak, TTL]
ESD protection
[1] Human body model — ±15kV [air-gap discharge] & ±8kV [contact
discharge]
[2] Core chipset — ±8kV
PCB stack-up 4-layer board [impedance control — differential 100Ω; single 50Ω]
Input 1x HDMI 2x HDMI 1x HDMI
1x RJ-45
Output 1x HDMI
8x RJ-45 8x RJ-45 7x HDMI
1x RJ-45
HDMI connector Type A [19-pin female]
RJ-45 connector WE/SS 8P8C with 2 LED indicators
DIP switch 8-pin DIP 6-pin DIP 2-pin DIP
Mechanical EX-G017A / EX-G017B EX-G015 EX-G016
Housing Metal case
Model 438 x 158 x 44mm [1’5.2”x6.2”x1.7”] 340x110x44mm
[1’1.4”x4.3”x1.7”]
Package 545 x 230 x 110mm [1’9.5”x9.1”x4.3”]
Dimensions
[L x W x H]
Carton 570 x 580 x 260mm [1’10.5”x1’10.9”x10.2”]
Model 1.4kg [3.1 lbs] 1.4kg [3.1 lbs] 1.4kg [3.1 lbs]
Weight Package 2.2kg [4.8 lbs] 2.2kg [4.8 lbs] 2.2kg [4.8 lbs]
Fixedness 1U rack-mount with ears
Power supply 5V 4A DC
Power consumption 13 Watts [max]
Operation
temperature 0~40°C [32~104°F]
Storage temperature -20~60°C [-4~140°F]
Relative humidity 20~90% RH [no condensation]
Package Contents
1x EX-G017A / EX-G017B / EX-G015 / EX-G016
2x Rack-mounting ears
1x 5V power adapter
1x User Manual
Page 7of 23

Model Name EX-G076A EX-G076B
Technical
Role of usage Receiver [long range RX] Receiver [short range RX]
HDMI compliance HDMI 1.2a
HDCP compliance Yes
Video bandwidth Single-link 165MHz [4.95Gbps]
Video support 480i / 480p / 720p / 1080i / 1080p60
HDMI over LAN cable
transmission range
Full HD (1080p)-40m (130ft) [CAT5e] / 50m (165ft) [CAT6]
HD (720p/1080i)-50m (165ft) [CAT5e] / 60m (200ft) [CAT6]
Audio support Surround sound (up to 7.1ch) or stereo digital audio
Equalization 8-level digital control None
Input TMDS signal 1.2 Volts [peak-to-peak]
Input DDC signal 5 Volts [peak-to-peak, TTL]
ESD protection
[CV-715]
[1] Human body model — ±15kV [air-gap discharge] & ±8kV [contact
discharge]
[2] Core chipset — ±8kV
PCB stack-up 4-layer board [impedance control — differential 100Ω; single 50Ω]
Input 1x RJ-45 1x RJ-45
Output 1x HDMI 1x HDMI
HDMI connector Type A [19-pin female] Type A [19-pin male]
RJ-45 connector WE/SS 8P8C with 2 LED indicators
Mechanical
Housing Metal case Plastic mold
Model 85 x 60 x 25mm [3.3”x2.4”x1”] 45 x 25 x 20mm [1.8”x1”x0.8”]
Package 270 x 175 x 80mm
[10.6”x6.9”x3.2”] 170 x 115 x 40mm [6.7”x4.5”x1.6”]
Dimension
s
[L x W x H]
Carton 450 x 370 x 300mm [1’5.7”x1’2.6”x11.8”]
Model 154g [5.4oz] 22g [0.8oz]
Weight Package 453g [1 lb] 90g [3.2oz]
Fixedness Wall-mount case upon request Direct plug-in
Power supply 5V 2A DC None
Power consumption 1 Watt [max] 0.5 Watt [max]
Operation temperature 0~40°C [32~104°F]
Storage temperature -20~60°C [-4~140°F]
Relative humidity 20~90% RH [no condensation]
Package Contents 1x EX-G076A
1x 5V power adapter
1x User Manual
1x EX-G076B
1x User Manual
Page 8of 23

Panel Descriptions
EX-G013A 1x2 HDMI over Single CAT5 Distribution
Amplifier
76
54
32
1
1. Power indicator
2. DIP switch [see table below]
3. HDMI In: Connect a HDMI source with a HDMI M-M cable here
4. Audio out: Plug in a local speaker here
5. HDMI Out: Connect to a HDMI display with a HDMI M-M cable here
6. RJ-45 Out: Link to EX-G013A for cascading; or link to CV-715 or CV-715s to another HDMI
display with a CAT5e/6 LAN cable
7. +5V DC: Connect to 5V 4A DC power supply
DIP Switch
Position
Pin#1 Pin#2 Video Audio Description
OFF
[©]OFF [©]1080p Stereo
1
Default Mode2– 1080p & stereo audio output for most
HDTVs
OFF
[©]ON [ª] 720p 1080i Stereo Safe Mode3– Enforce the system output at 720p/1080i video
and stereo audio for basic compatibility among HDTVs
ON [ª] OFF [©]Bypas
s4Bypas s4
EDID Learning Mode5– for learning EDID from the display
while playing any received HDMI audio format
ON [ª] ON [ª]Bypas
s Stereo
EDID Learning & Stereo mode5– for learning EDID from
the display while enforcing stereo output if any HDTV cannot
play surround sound normally
Note for EDID (Extended Display Identification Data) learning
1. Don’t plug in HDMI cable to [HDMI In] when you want to restore default EDID or learn the display’s
EDID.
2. Please connect the display which you want to read EDID to HDMI Out so the EX-G013A can learn the
EDID information from the connected HDTV.
3. To learn EDID from HDMI display, pull up-and-down the DIP switch 1 from OFF to ON, the green light
will dim and light to indicate the EDID learning process is complete. You DON’T NEED to pull up the
DIP switch again unless you want to learn another EDID by pulling DIP switch 1 up and down.
Page 9of 23

Note
1If the HDTV shows video but without audio, please try to set audio mode to stereo.
2Factory default: Pin#1-OFF[©], Pin#2- OFF[©]for 1080p with stereo.
3If you encounter any unsolved audio/video output problem during system installation, please turn to
Safe Mode (Pin#1-OFF[©]& Pin#2-ON[ª]) to enforce the most compatible 720p stereo output for
system check.
4Bypass means the matrix will maintain playing the original format of HDMI signals in video and
perhaps audio. By setting at this mode, the users may encounter compatibility issue among different
kinds of HDMI sources and displays. If you cannot get the audio and/or video output normally at the
system installation, please change the DIP switch setting to default mode or even safe mode to verify
the functionality of the device.
5Set Pin#1 at ON[ª]first then connect the HDMI Input to HDTV through a HDMI cable. Wait for 20
seconds. The EDID learning procedure will be finished. If you want to learn the EDID from another
HDTV, you must set Pin#1 at OFF first and repeat this procedure.
EX-G013B 1x2 HDMI over Single CAT5 Cascading
Distribution Amplifier
1 2 3 4 5 6 7
1. Power indicator
2. 16-level rotary control: Adjust the 16-level equalization control corresponding to the
transmission distance of receiving HDMI signals. For surround sound audio output, please
adjust from 0-to-7 (longest-to-shortest transmission length). For stereo audio output, please
adjust from 8-to-F (longest-to-shortest transmission length). It is recommended to adjust
from 7-to-0 or from F-to-8 to find the optimal visual experience.
3. RJ-45 In: Link to EX-G007-TX, EX-G013A, or EX-G013B with a CAT-5e/6 cable
4. Audio out: Plug in a local speaker here
5. HDMI Out: Connect to a HDMI display with a HDMI M-M cable here
6. RJ-45 Out: Link to another EX-G013B for cascading; or link to EX-G076A or EX-G076B to
another HDMI display with a CAT5e/6 cable
7. +5V DC: Connect to 5V 4A DC power supply
Page 10of 23

EX-G017A/B 1x9 HDMI over Single CAT5 Distribution Amplifier with
7.1ch audio
4 5 6
3
21
1. Power jack 5V DC
2. HDMI input: connect a HDMI source here
3. HDMI output: connect a local HDMI display here
4. DIP switch: see the definition below
5. Rotary controller: see the definition below
6. Out1-Out8: RJ45 output 1-8: link to the HDMI over CAT5 receiver EX-G076A or EX-G076B; or
cascade to EX-G016
DIP switch
The EX-G017A & EX-G017B can display HDMI signals on DVI devices by configuring each DIP
switch.
DIP Switch: OFF[©] for HDMI display / ON[ª] for DVI display
Green LED: Bright when HDMI input signal is detected; dim when DVI input signal is detected.
For example: Output 1 to HDMI TV and Output 2 to DVI monitor. Set DIP switch at Pin#1- OFF[©] and
Pin#2- ON[ª] position.
Page 11of 23

Video Patterns
The Rotary controller on EX-G017A allows you to send several test patterns.
Mode 0 (EX-G017A): Stereo audio mode
Mode 0 (EX-G017B): Surround sound audio mode
Mode 1 (EX-G017A): Running circles Mode 2: Running circles with changing radius
Mode 1 (EX-G017B): Stereo audio mode
Mode 3: White running circle with black background Mode 4: Black running circle with white
background
Mode 5:Colorbar Mode 6: Mosaic
Mode 7: Check board I Mode 8: Check board II
Page 12of 23

Mode 9:Purered Mode A: Pure green
Mode B: Pure blue Mode C: Pure black
Mode D:Purewhite Mode E: Write default EDID
Mode F: Save EDID from the display connected to HDMI Out
Note for EDID (Extended Display Identification Data) learning
1. Don’t plug in HDMI cable to HDMI input connector while processing writing default EDID or
writing display’s EDID.
2. Please connect the display which you want to read EDID to HDMI Out and turn Mode to F
for 5-10 seconds so the BTM18 can learn the EDID information from the connected HDTV.
3. Turn Mode clockwise from Mode F to Mode 0 and enjoy the experience. DO NOT let the
rotary arrow pass by Mode E which will erase the EDID just learned and set back to default
EDID.
EX-G076A HDMI over Single CAT5 Receiver
HDMI-OUT
EQ
HDMI-OUT: Connect to a HDMI display with a HDMI M-M cable here.
EQ: Adjust the 8-level equalization control knob to the received HDMI signals. 0 – 7 = strongest –
weakest. It is recommended to switch from 7 to 0 to find the optimal visual experience.
Page 13of 23

EX-G015 2x8 HDMI over Single CAT5 Matrix Switch
5
4321
1. +5V DC: Power jack for 5V4A DC
2. HDMI In1: HDMI Input1 for connecting to a HDMI source here
3. HDMI In2: HDMI Input2 for connecting to a HDMI source here
4. EDID: DIP Switch (see the definition in the next section)
5. Out1 – Out8: RJ-45 Output 1-8 to link to the HDTV through HDMI over CAT5 receiver
EX-G076A or EX-G076B
DIP Switch
Switch
Position OFF [©]ON [ª]
Pin#1 Input HDMI source #1 Input HDMI source #2
Pin#2 Source 1 use default EDID Source 1 use learned EDID1
Pin#3 Source 2 use default EDID Source 2 use learned EDID2
Pin#4 7.1 Channel32 Channel
Pin#5 HDMI 1.2 output HDMI 1.3 output
Pin#6 HDMI mode output DVI mode output
1Set pin#2-ON [ª]firstly and then connect the HDMI Input to HDMI display through HDMI
cable. Waiting for 20 seconds, the learning procedure will be accomplished. When update
the EDID content with another display, you must set pin#2-OFF[©]and repeat this
procedure again.
2Set pin#3-ON [ª]firstly and then connect the HDMI Input to HDMI display through HDMI
cable. Waiting for 20 seconds, the learning procedure will be accomplished. When update
the EDID content with another display, you must set pin 3 off and repeat this procedure
again
3While 7.1 channel option is selected for the HDMI signal with only stereo audio, the
HDMI display may show video without audio. In this case, please set audio to stereo
audio.
Page 14of 23

EX-G016 2x8 HDMI over Single CAT5 Cascading Distribution
Amplifier
Front Panel
43
1
2
1. 1.2a/1.3a: Output format LED indicator [Green: HDMI 1.3 / Red: HDMI 1.2]
2. Format Sel: Push button for HDMI output format selection
3. IN 1/IN 2: Input LED indicator [Green: HDMI input / Red: RJ-45 input]
4. IN Sel: Push button for input HDMI source selection
Rear Panel
5678 9 10 1112
5. Dip Switch: EDID/Audio setting [see following section]
6. EQ: Rotary control for equalizer setting [see following section]
7. RJ-45 IN 1: for cascading from another EX-G016 or EX-G013B
8. HDMI IN 2: for connecting to video source, EX-G013A, EX-G017A, or another EX-G016
9. RJ-45 OUT: for connecting to display through EX-G076A or EX-G076B; or for cascading to
another EX-G013B or EX-G016
10. HDMI OUT1-HDMI OUT7: for connecting to display through HDMI cable or through Cat-5e cable
with EX-G076B attached; or for cascading to another EX-G013A, EX-G017A, or EX-G016.
11. +5V DC power: connect to 5V 4A DC interlocking power adapter
12. Power ON/OFF switch
Page 15of 23

DIP Switch
Pin#1
Position OFF [©]ON [ª]Pin#2 Position OFF [©]ON [ª]
EDID Mode Use Default
EDID Use learned
EDID1Audio Mode 7.1 Channel2Stereo
Note
1 Set pin#1-ON[ª]first and then connect the HDMI Input to HDMI display thru HDMI cable. Wait
for 20 seconds. The Recording Procedure will be finish. If you want to learn the EDID for
another equipped display, you must set pin#1-OFF[©]and repeat the procedure.
2 If the equipped display shows video but without audio, please try to set audio to 2 channel.
Rotary Control
In order to adapt the CAT5 cable, EX-G016 offers 8 level equalization control on the
received HDMI signal. The strongest equalization is applied while the knob stops at
number 0, while the weakest equalization happens at number 7. It is recommended to
switch from 7 to 0 to find the optimal visual experience.
HDMI Output Format Selection
When input signal exists, the output format LED turns on. If the input HDMI source is HDMI 1.3
format, you can set the output format to HDMI 1.2 mode and Red LED will be on. If the input HDMI
source is HDMI 1.2, the output format is always set to HDMI 1.2.
Page 16of 23

Hardware Installation
EX-G013A
Extends HDMI signals to next cascading device with one local display
1.Switch off all devices, including monitors.
2.Connect a local HDMI display to the HDMI out of the EX-G013A and then connect a speaker to the
3.5mm audio socket.
3.Connect to a HDMI source (such as a Blu-Ray Disc player)
4.Connect EX-G013A to EX-G013B (for cascading), to EX-G076A (to HDTV at long range), or
EX-G076B (to HDTV at mid range) via RJ-45 Out by a CAT5 cable.
5.Plug in 5V 4A DC power supply.
6.Power on the HDTV.
7.Power on the HDMI source.
HDMI source
EX-G076B
HDTV
HDMI cable
CAT5 cable
Audio cable
EX-G076A
EX-G013B
EX-G013A
HDMI cable
Speaker
Page 17of 23

EX-G013B
Relays HDMI signals to next cascading device with one local display
1.Switch off all devices, including monitors.
2.Connect a local HDMI display to the HDMI Out of the EX-G013B and then connect a speaker to the
3.5mm audio socket.
3.Connect to EX-G013B via RJ-45 in by a CAT5 cable.
4.Connect to next EX-G013B (for cascading), to EX-G076A (to HDTV at long range), or EX-G076B
(to HDTV at mid range) via RJ-45 out by a CAT5 cable.
5.Plug in 5V 4A DC power supply.
6.Power on the HDTV.
EX-G013A
EX-G013B
CAT5 cable
Speaker
HDMI cable
HDTV EX-G076B
EX-G076A
EX-G013B
CAT5 cable
Audio cable
Page 18of 23

EX-G017A / EX-G017B
Broadcasts HDMI signals to 8 remote displays and one local display
1.Switch off all devices, including monitors.
2.Connect a local HDMI display to the HDMI Out of the EX-G017A or connect to EX-G013A for
cascading.
3.Connect a HDMI source (such as a Blu-ray Disc player) to the HDMI In.
4.Connect to the receivers (EX-G076A or EX-G076B) via RJ45 connectors by a CAT5e cable.
5.Plug in 5V 4A DC power supply.
6.Power on the HDMI monitors.
7.Power on the HDMI source.
HDMI source
HDMI cable
EX-G017A
EX-G017B
HDTV
EX-G076A
EX-G076B
HDMI cable
HDTV
HDTV
Page 19of 23

EX-G015
Broadcasts HDMI signals to 8 remote displays from either of two HDMI
sources
CAT5 cable up to 25m (80ft)
CAT5 cable
up to 60m (200ft)
EX-G015
HDTV#1
EX-G076B EX-G076B
HDTV#2
CAT5 cable
HDMI source #2
HDMI cable
HDMI cable
CAT5 cable
HDTV#4
HDMI cable
EX-G076B
HDMI cable
HDMI cable
EX-G076A
EX-G076A
EX-G076A
EX-G076A
HDTV#7
HDTV#8
EX-G076B
CAT5 cable
HDTV#3
HDMI cable
HDMI source #1
HDTV#6
HDTV#5
Page 20 of 23