Mellanox Technologies MTS3610Q-6UNC User manual

www.mellanox.com
324 PORT QDR InfiniBand Switch Platform
User’s Manual
PN: MTS3610Q-6UNC, MTS3610D-6UNC
Rev 1.7

Mellanox Technologies
350 Oakmead Parkway
Sunnyvale, CA 94085
U.S.A.
www.mellanox.com
Tel: [phone]
Fax: [phone]
Mellanox Technologies, Ltd.
PO Box 586 Hermon Building
Yokneam 20692
Israel
Tel: [phone]
Fax: [phone]
© Copyright 2009. Mellanox Technologies, Inc. All Rights Reserved.
Mellanox®, ConnectX®, InfiniBlast®, InfiniBridge®, InfiniHost®, InfiniRISC®, InfiniScale®, and InfiniPCI® are registered
trademarks of Mellanox Technologies, Ltd.
BridgeX, PhyX and Virtual Protocol Interconnect are trademarks of Mellanox Technologies, Ltd.
All other marks and names mentioned herein may be trademarks of their respective companies.
InfiniScale® IV 324-Port QDR InfiniBand Switch User’s Manual
Document Number: 2981
Rev 1.7
Mellanox Technologies
2
NOTE:
THIS HARDWARE, SOFTWARE OR TEST SUITE PRODUCT (“PRODUCT(S)”) AND ITS RELATED DOCUMENTATION ARE
PROVIDED BY MELLANOX TECHNOLOGIES “AS-IS” WITH ALL FAULTS OF ANY KIND AND SOLELY FOR THE PURPOSE
OF AIDING THE CUSTOMER IN TESTING APPLICATIONS THAT USE THE PRODUCTS IN DESIGNATED SOLUTIONS. THE
CUSTOMER'S MANUFACTURING TEST ENVIRONMENT HAS NOT MET THE STANDARDS SET BY MELLANOX
TECHNOLOGIES TO FULLY QUALIFY THE PRODUCTO(S) AND/OR THE SYSTEM USING IT. THEREFORE, MELLANOX
TECHNOLOGIES CANNOT AND DOES NOT GUARANTEE OR WARRANT THAT THE PRODUCTS WILL OPERATE WITH THE
HIGHEST QUALITY. ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT ARE
DISCLAIMED. IN NO EVENT SHALL MELLANOX BE LIABLE TO CUSTOMER OR ANY THIRD PARTIES FOR ANY DIRECT,
INDIRECT, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES OF ANY KIND (INCLUDING, BUT NOT LIMITED TO,
PAYMENT FOR PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY FROM THE USE OF THE PRODUCT(S) AND
RELATED DOCUMENTATION EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

19U QSFP SDR/DDR/QDR InfiniBand Switch Platform User’s Manual Rev 1.7
Mellanox Technologies 3
Table of Contents
Table of Contents 3
Table of Figures 5
Table of Lists 6
About this Manual 7
Intended Audience 7
Related Documentation 7
Revision History 8
Chapter 1 Overview 9
1.1 Serial Number and Product Version Information 9
Chapter 2 Safety Warnings and LED Indications 12
2.1 InstallationSafetyWarnings 12
2.2 LEDStatusIndicators 15
2.2.1 Power Supply Unit LEDs 15
2.2.2 Leaf Board LED Indicators 15
2.2.3 Spine Board LED Indicators 16
2.2.4 Management Module LED Indicators 18
Chapter 3 Installation 20
3.1 PackageContents 20
3.2 PhysicalInstallation 20
3.2.1 ESD Connection 21
3.2.2 Installing the Chassis 21
3.2.3 Ground Connections 26
3.2.4 Installing the Cable Holder 27
3.2.5 Power Connections 27
3.2.6 InfiniBand QSFP Cable Installation 30
Chapter 4 Switch Power Up 31
4.1 Power Supply and Spine Board Indicator Status at Power ON 31
4.2 InfiniBand Fabric Initialization and Management 31
Chapter 5 Insertion and/or Hotswap Extraction 33
5.1 Power Supply Units 33
5.2 Extracting and Inserting the Power Supply Unit 33
5.3 LeafBoards 34
5.3.1 Extracting a Leaf Board 34
5.3.2 Inserting a Leaf Board 35
5.4 SpineBoards 35
5.4.1 Extracting a Spine Board 35
5.4.2 Inserting a Spine Board 36
5.5 FanModules 37
5.5.1 Leaf Fan Module 37
5.5.2 Spine Fan Modules 38
5.6 ManagementModule 39
5.6.1 Extracting a Management Module 39
5.6.2 Inserting a Management Module 40
5.7 ReplacingtheBattery 40
5.8 Over-temperatureShutdownMechanism 41
Chapter 6 Disassembly and Disposal 42
6.1 DisassemblingtheChassis 42

Rev 1.7
Mellanox Technologies
4
6.1.1 Removing the Chassis 43
6.1.2 Removing the Bottom Shelf 44
6.2 Disposal 44
Chapter 7 Switch Management Tools 45
7.1 ChassisManagement 45
Chapter 8 FabricITManagement 46
8.1 Downloading FabricIT Software and Documents 46
8.2 InstallingLicenses 46
8.2.1 FabricIT Management and Inspection License 46
Chapter 9 TroubleShooting 47
9.1 Power Supply Unit 47
9.2 LeafBoard 47
9.3 ManagementModule 48
9.4 SpineBoard 48
9.5 ManagementModule 49
Appendix A 19U QSFP DDR/QDR IB Switch Specification Data 50
Appendix B Mechanical Drawing 53
Appendix C QSFP Interface 55
Appendix D Ethernet RJ 45 Connector 57
Appendix E Sample In-band FW Upgrade 58
Appendix F Replacement Parts Ordering Numbers 64
Appendix G Avertissements de sécurité d’installation (French) 67
Appendix H Installation - Sicherheitshinweise (German) 70
Appendix I Special Regulations Regarding Finland, Sweden, Denmark, and Norway 73

19U QSFP SDR/DDR/QDR InfiniBand Switch Platform User’s Manual Rev 1.7
Mellanox Technologies 5
Table of Figures
Figure 1: Generic Product label 9
Figure 2: Switch Views 11
Figure 3: Power Supply Unit Status Indications 15
Figure 4: Leaf Board Status Indications 15
Figure 5: Connector Physical and Logical Link Indications 16
Figure 6: LED Indications When the Leaf is Working Properly 16
Figure 7: Spine Board Status Indications 17
Figure 8: Management Module Status Indications 18
Figure 9: ESD Connector 21
Figure 10: Installation Kit Parts 22
Figure 11: Vertical Rails to Cabinet Measurement 23
Figure 12: Caged Nut Insertion 23
Figure 13: Rail Slide Installation 24
Figure 14: Shelf Installation 24
Figure 15: Mechanical Lifting Device 24
Figure 16: Face Plate Mounting Bolt Locations 25
Figure 17: Lock Down Bar 26
Figure 18: Ground Connection 26
Figure 19: Electrical Cable Clamp 28
Figure 20: Multiple Power Inlets - Electric Caution Notification 29
Figure 21: Power Supply with Cable Attached 34
Figure 22: Retaining Screw and Red Button 35
Figure 23: Spine Board Extraction 36
Figure 24: Leaf Fan Module Extraction 38
Figure 25: Spine Fan Module Extraction 39
Figure 26: Management Module 40
Figure 27: Lock Down Bar 42
Figure 28: Face Plate Mounting Bolt Locations 43
Figure 29: Mechanical Lifting Device 43
Figure 30: Shelf Removal 44
Figure 31: Rail Slide Removal 44
Figure 32: Front Panel 53
Figure 33: Rear Panel Leaf Side of the Switch 54
Figure 34: QSFP Connector Male and Female Views 56
Figure 35: Ethernet RJ45 Connector 57

Rev 1.7
Mellanox Technologies
6
Table of Lists
Table 1: Reference Documents and Web Sites 7
Table 2: Revision History of this User’s Manual 8
Table 3: Switch Rack Mechanical and Environmental Requirements (Fully Populated Chassis) 10
Table 4: LEDs Display for Normal Operation 18
Table 5: HCA Cards Certification Status 50
Table 6: Switch Specification Sheet MTS3610D and MTS3610Q 50
Table 7: InfiniBand QSFP Connector Pinout 55
Table 8: Replacement Parts Ordering Numbers 64

19U QSFP SDR/DDR/QDR InfiniBand Switch Platform User’s Manual Rev 1.7
Mellanox Technologies 7
About this Manual
This manual provides an overview of the 19U 18 slot QSFP Chassis InfiniBand Switch Platform
and guidelines for its operation.
Intended Audience
This manual is intended for users and system administrators responsible for installing and setting
up the switch platform.
The manual assumes familiarity with the InfiniBand®architecture specification.
Related Documentation
The documentation set accompanying the 19U 18 slot QSFP Chassis InfiniBand Switch platform
includes the following:
Table 1 - Reference Documents and Web Sites
Switch Firmware and Firmware Update Tools See
http://www.mellanox.com > Downloads > Firmware Tools.
Note that the Switch System described in this manual is based on
Mellanox Technologies’ InfiniScale®IV switch device.
FabricIT Enterprise Fabric Management Software
CLI User’s Manual Talk to your Mellanox representative for information regarding licensing and implementation of the FabricIT Enterprise Fabric
Management Software System.
Mellanox OFED Stack for Linux User’s Manual See
http://www.mellanox.com > Downloads > InfiniBand SW/Driv-
ers,
Click “Mellanox OpenFabrics Enterprise Distribution for Linux
(MLNX_OFED)”
Select the Linux User’s Manual
The embedded OS and tools on the CPU in the management
module is a subset of the Mellanox OFED stack.
IB Switch Platforms Embedded Management Tools
Document no. 2141UM Describes the Embedded Management Tools (EMGT) package,
which provides Out-of-Band management capabilities for Infini-
Band switches.
Available from http://docs.mellanox.com (requires a Mellanox
Technologies customer account).

Rev 1.7
Mellanox Technologies
8
Revision History
Table 2 - Revision History of this User’s Manual
Revision Date Details
1.7 Dec. 2009 Imported new template
Added Fabric IT Management Chapter 8.
Added “When first installed the chassis needs an initial configuration of the
management module. See the Installation Guide for instructions on Initail con-
figuration and remote management. After the inital configuration the chassis
will start up using an InfiniBand fabric standard compliant Subnet Manage-
ment software.” in Ch 3 on page 20
Added power cable type to parts list
1.6 May, 2009 Added WEEE Disposal section
Added Disassembly instructions
Explanation of the Mammoth Chassis GUID.
Minor formatting changes.
Removed line
5.Make sure the Leaf board and the HCA cards have the same version of the
FW.
1.5 May, 2009 Updated management module LEDs and Reset/Restore button.
1.4 May, 2009 Removed parts of section 6 and replaced with Fabric IT link
Photoshopped in new management module graphics
Added Cable holder installation
1.3 April,
2009 Updated installation with new parts
1.2 Mar, 2009 Updated installation with new parts
1.1 Feb, 2009 added max time a fan module can be removed, and LED reset of the fan leds
1.0 Jan, 2009 Added Installation instructions and added info on EMGT.

19U QSFP SDR/DDR/QDR InfiniBand Switch Platform User’s Manual Rev 1.7
Mellanox Technologies 9
1 Overview
This User’s Manual provides an overview of the 19U QSFP DDR/QDR Modular InfiniBand
Switch Platform (‘the switch’) and the operational environment.
Mellanox MTS3610 switch systems provide the highest performing fabric solution by delivering
high bandwidth and low latency to Enterprise Data Centers, High-Performance Computing and
Embedded environments. Networks built with MTS3610 systems can carry converged traffic with
the combination of assured bandwidth and granular quality of service. Built with Mellanox’s 4th
generation InfiniScale® IV InfiniBand switch device, MTS3610 systems provide up to 40Gb/s full
bidirectional bandwidth per port. With 324 ports, these systems are among the densest switching
systems available.
The switch platform comes pre-installed with all necessary firmware and configured for standard
operation within an InfiniBand fabric, and requires an InfiniBand compliant Subnet Manager run-
ning from one of the hosts. All that is required for normal operation is to follow the usual precau-
tions for installation and to connect the switch to the HCAs. Once connected, the Subnet
Management software automatically configures and begins utilizing the switch.
It is recommended that the Mellanox OpenFabrics software package be installed on all nodes con-
nected to the MTS3610. The software package provides a subnet manager and network manage-
ment tools as well as connectivity software for servers and storage, and is available on the
Mellanox web site.
Basic installation, hot-swapping components and hardware maintenance is covered in “Installa-
tion” on page 20.
1.1 Serial Number and Product Version Information
The serial number and product version information are found on the label seen in the figure below.
Figure 1: Generic Product label
Also on this label is the GUID identifier for the switch.
This is the System Image GUID according to the IB spec. It is burned on the board which is in the
chassis. All the boards and the management SW looks for this GUID in addition to their own Node
GUID.

OverviewRev 1.7
Mellanox Technologies
10
The switch ships in a minimum base configuration plus additional modules depending on the cho-
sen customer configuration. Optional modules include:
• Leaf boards
• Power supply units
• Management modules
Figure 2 shows the front and rear sides fully populated.
Table 3 - Switch Rack Mechanical and Environmental Requirements (Fully Populated Chassis)
Rack
Height Rack Width Rack Depth Weight Max. Power (324 x QSFP Ports) Ambient Temp.
19U
(842 mm) 19” (EIA- 310)
(482.6 mm)
25.7”
652.8mm 105.68 kg min configu- ration
233 lbs. min configura-
tion
153 kg full configura-
tion
347 lbs. full configura-
tion
DDR – 4765 [W] @ 220VAC
QDR – 5170 [W] @ 220VAC
Up to eight Power Supplies of 100-
240VAC, 50-60Hz, 13-6.3A
Max: 45ºC
Min: 10ºC

19U QSFP SDR/DDR/QDR InfiniBand Switch Platform User’s Manual Rev 1.7
Mellanox Technologies 11
Figure 2: Switch Views
Leafs
Each leaf has 18 Ports and up to 18 leafs
can fit in the chassis.
Spine Fan Module with four
internal fans.
Two management Modules.
Up to 8 Power Supply Units
6 Required and 2 for redundancy to allow
hotswapping.
The chassis needs all nine spines for the
switch system to run properly.
The leaf fan module contains 7 internal
fans.
Four spines to the right of the fan module
and five spines to the left of the fan mod-
ule.

Safety Warnings and LED IndicationsRev 1.7
Mellanox Technologies
12
2 Safety Warnings and LED Indications
2.1 Installation Safety Warnings
1. Installation Instructions
2. Bodily Injury Due to Weight
3. Over-temperature
4. Stacking the Chassis
5. Redundant Power Supply Connection - Electrical Hazard
6. During Lightning - Electrical Hazard
Read all installation instructions before connecting the equipment to the
power source.
This equipment is very heavy and should be moved using a mechanical
lift to avoid injuries.
This equipment should not be operated in an area with an ambient tem-
perature exceeding the maximum recommended: 45°C (113°F). More-
over, to guarantee proper air flow, allow at least 8cm (3 inches) of
clearance around the ventilation openings.
The chassis should not be stacked on any other equipment. If the chassis
falls, it can cause bodily injury and equipment damage.
This product includes a redundant power or a blank in its place. In case
of a blank power supply, do not operate the product with the blank cover
removed or not securely fastened.
During periods of lightning activity, do not work on the equipment or
connect or disconnect cables.

19U QSFP SDR/DDR/QDR InfiniBand Switch Platform User’s Manual Rev 1.7
Mellanox Technologies 13
7. Copper InfiniBand Cable Connecting/Disconnecting
8. Rack Mounting and Servicing
9. Equipment Installation
10. Equipment Disposal
11. Local and National Electrical Codes
12. Battery Replacement
Copper InfiniBand cables are heavy and not flexible, as such they should
be carefully attached to or detached from the connectors. Refer to the
cable manufacturer for special warnings/instructions.
When this product is mounted or serviced in a rack, special precautions
must be taken to ensure that the system remains stable. In general you
should fill the rack with equipment starting from the bottom to the top.
This equipment should be installed, replaced, and/or serviced only by
trained and qualified personnel.
Disposal of this equipment should be in accordance to all national laws
and regulations.
This equipment should be installed in compliance with local and national
electrical codes.
There is a risk of explosion should the battery be replaced with a battery of an
incorrect type.
Dispose of used batteries according to the instructions.

Safety Warnings and LED IndicationsRev 1.7
Mellanox Technologies
14
13. UL Listed and CSA Certified Power Supply Cord
14. Leakage >3.5mA
15. Add GND connection information
16. Installation codes
17. Interconnection of units
18.WEEE Directive
For North American power connection, select a power supply cord that is UL
Listed and CSA Certified, 3 - conductor, [18 AWG], terminated with a molded
plug rated at 125 V, [15 A], with a minimum length of 1.5m [six feet] but no
longer than 4.5m.
For European connection, select a power supply cord that is internationally
harmonized and marked "<HAR>", 3 - conductor, minimum 0,75 mm2 wire,
rated at 300 V, with a PVC insulated jacket. The cord must have a molded plug
rated at 250 V, 10 A."
WARNING: High leakage current; Earth connection essential before connect-
ing supply.
Before connecting this device to the power line, the protective earth terminal
screws of this device must be connected to the protective earth in the building
installation.
This device must be installed according to the latest version of the country
national electrical codes. For North America, equipment must be installed in
accordance to the applicable requirements in the US National Electrical Code
and the Canadian Electrical Code.
Cables for connecting to the unit RS232 and Ethernet Interfaces must be UL
certified type DP-1 or DP-2. (Note- when residing in non LPS circuit)
Overcurrent Protection: A readily accessible Listed branch circuit overcurrent
protective device rated 20 A must be incorporated in the building wiring.
According to the WEEE Directive 2002/96/EC, all waste electrical and
electronic equipment (EEE) should be collected separately and not dis-
posed of with regular household waste.
Dispose of this product and all of its parts in a responsible and environ-
mentally friendly way.

19U QSFP SDR/DDR/QDR InfiniBand Switch Platform User’s Manual Rev 1.7
Mellanox Technologies 15
2.2 LED Status Indicators
2.2.1 Power Supply Unit LEDs
Each Power Supply Unit has three indicator LEDs.
Figure 3: Power Supply Unit Status Indications
AC– When lit this LED indicates input voltage between 100 and 240 Volts.
DC FAIL –When lit this LED indicates a fault in the power supply.
DC OK – When lit this LED indicates that the output from the power supply is +48 VDC.
2.2.2 Leaf Board LED Indicators
Each leaf board has two Status LEDs (Green and Yellow), and 36 Connector LEDs (two per con-
nector).
When the Green, board status LED labelled PWR is on, this indicates that there is power to the leaf
board. If the Green LED is off, uninstall and reinstall the leaf board.
When the Yellow board status LED labelled ATTN is on, this indicates that there is a fault in the
leaf board. If the Yellow LED is on, uninstall and reinstall the leaf board.
For more information see Section 9, “TroubleShooting,” on page 47.
Figure 4: Leaf Board Status Indications
Each of the 18 connectors on the Leaf board has two LEDs that indicate if there is a physical and
logical connection. The figure below explains the connector status according to its LED display.
DC AC
OK FAIL OK
Power — When lit there
is a proper power supply
to the leaf board.
Fault — When lit there is
a fault in the leaf board.

Safety Warnings and LED IndicationsRev 1.7
Mellanox Technologies
16
Figure 5: Connector Physical and Logical Link Indications
Note: The switch does not provide a visual means that indicates the port speed configuration
(SDR, DDR, or QDR) and/or the link width (1X or 4X). The speed and link width configura-
tions can be retrieved using FabricIT management software.
Figure 6: LED Indications When the Leaf is Working Properly
2.2.3 Spine Board LED Indicators
Each spine has two status LEDs for the spine and 72 status LEDs for the leaf boards. Each leaf
board is connected by two links to each spine module. These are displayed on the spine as link A
and link B.
The two status LEDs for the spine have the configuration shown in Figure 7. The LEDs indicate as
follows:
Table 4 - Connector LEDs
LED Description
Physical Link - Green
Constant on indicates a good physical link
Blinking indicates a problem with the Physical link
Off indicates No Physical link. Cable may be unseated or unconnected
Data Activity - Yellow
Blinking indicates Data Transfer
Blinking rate is proportional to traffic rate
Constant on indicates no Data Transfer
Port number
This LED should be off.
This LED should be on.
The yellow connector
LEDs should be blinking.
The green connector
LEDs should be on.

19U QSFP SDR/DDR/QDR InfiniBand Switch Platform User’s Manual Rev 1.7
Mellanox Technologies 17
• ATTN – Yellow indicates fault in spine.
• PWR – Green indicates that the spine is receiving the proper voltage.
Figure 7: Spine Board Status Indications
The 72 status LEDs for the leafs have the configuration shown in Figure 7. The leaf number is fol-
lowed by four LEDs. These LEDs indicate the condition of the leaf as follows:
Link A and Link B
Each of the leafs is connected to each of the spines through two links.
• Yellow – indicates that there is a logical connection to the spines through this link.
• Green – indicates that there is a physical connection to the spines through this link.
Green – indicates Power OK
ATTN – Yellow indicates fault in
spine, normally off
Green – indicates that there is
a physical connection to the
spines through this link.
Yellow – indicates that there is a
logical connection to the spines
through this link.
Links A and B to each leaf
Leaf numbers

Safety Warnings and LED IndicationsRev 1.7
Mellanox Technologies
18
2.2.4 Management Module LED Indicators
The switch system requires at least one management module.The management module has three
interfaces to connect to the MTS3610. They are:
• 1 RS232 “CONSOLE” connector
•1USBport
• 1 Ethernet “MGT”connector
There is also a Reset/Restore button. This button resets all of the leafs in the chassis by bringing
them down and powering them up when the button is pushed. When the button is held down for 15
seconds the chassis is reset and the factory defualt values for the configuration are implemented.
Figure 8: Management Module Status Indications
The management module LEDs display the switch system operating conditions.
Table 5 - LEDs Display for Normal Operation
LED Description Normal
State
STATUS Off = No Power
Green = Unit is operating well- all temp. and voltages are OK.
Yellow = System warning. Attention needed (such as overheating).
Red = System not operational (Diagnostics fail, CPU hang,
HW fail, Overheat-critical)
Blinking Yellow=Restore factory defaults in progress.
Green
PS off = No power
Green = operational
Red = PS fault detected. User should check individual power supplies for
fault indications.
Green
FAN SPINE off = No power to fan
Green = operational
Red = Fault detected (fan broken, can't reach full RPMs)
Green

19U QSFP SDR/DDR/QDR InfiniBand Switch Platform User’s Manual Rev 1.7
Mellanox Technologies 19
FAN LEAF off = No power to fan
Green = operational
Red = Fault detected (fan broken, can't reach full RPMs)
Green
MASTER-
SLAVE off = no power Green = Management module is operating as a master (i.e., the other
management module is a Slave)
Yellow = Management module is operating as a slave (other management
module is the master).
When only one management is present in the system, default is Green
On.
LED Description Normal
State

InstallationRev 1.7
Mellanox Technologies
20
3Installation
Installation and initialization of the chassis is a simple process requiring attention to the normal
mechanical, power, and thermal precautions for rack-mounted equipment. When first installed the
chassis needs an initial configuration of the management module. See the Installation Guide for
instructions on Initail configuration and remote management. This ensures that OpenSM will be
running on the system. After the inital configuration the chassis will start up using an InfiniBand
fabric standard compliant Subnet Management software.
3.1 Package Contents
The package includes:
• 1 Chassis
• 1-18 leafs according to the amount ordered
• 18 - X leaf blanks X = the amount ordered
• 1 leaf fan module
• 1 spine fan module
•9spines
• 1- 2 management modules according to the amount ordered. If only 1 management module is
ordered then one management module blank will be in the package.
• 1) power cable for each PSU– Type B 13ft US 125V 15A Right angle chord.
• 6-8 PSUs depending upon your specific order
• (8 - X) PSU blanks X = the amount ordered
• RJ45 to DB9 cable
• 1 Installation kit
•CD
• Installation guide
Before you install your new MTS3610 Chassis, unpack the system and check to make sure that all
the parts have been sent, check this against the parts list. Check the parts for visible damage that
may have occurred during shipping.
Note: If anything is damaged or missing, contact your customer representative immediately.
3.2 Physical Installation
Note: You will need a mechanical lift, to move and insert the chassis into the rack.
Warning: This equipment is very heavy. Safety is the first concern. The fully
loaded chassis weighs ~350 lbs (155 kg). Make sure that proper manpower and
equipment is used for transporting and moving the chassis.