Memorex Mi1200 - CD Micro Stereo System User manual

1
SAFETY PRECAUTIONS
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL. (This Caution Marking with Rating Label is located at the
bottom and rear enclosure of the unit.)
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
DANGEROUS VOLTAGE:
The lightning flash with arrowhead symbol within an
equilateral triangle is intended to alert the user to the
presence of uninsulated dangerous voltage within the
product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
ATTENTION:
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
FCC WARNING: This equipment may generate or use radio frequency
energy. Changes or modifications to this equipment may cause harmful
interference unless the modifications are expressly approved in the
instruction manual. The user could lose the authority to operate this
equipment if an unauthorized change or modification is made.
DANGER:
Invisible and hazardous laser radiation when open and
interlock failed or defeated. Avoid direct exposure
to beam.
iPod is a trademark of Apple Computer, Inc., registered in the U.S. and
other countries.

2
SAFETY PRECAUTIONS
INFOR ATION
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy, and if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO
NOT EXPOSE THIS UNIT TO RAIN OR OISTURE.
SURGE PROTECTORS:
It is recommended to use a surge protector for AC connection. Lightning
and power surges ARE NOT covered under warranty for this product.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003
du Canada.
LASER SAFETY: This unit employs a laser. Only qualified service
personnel should attempt to service this device due to possible eye injury.
CAUTION: USE OF CONTROLS, AD USTMENTS, OR
PERFORMANCE PROCEDURE HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.
ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA
LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE
CORRESPONDANTE DE LA PRISES ET POUSSER USQU’AU FOND.

3
Dear Customer:
Selecting fine audio equipment such as the unit you’ve just purchased is only the start of
your musical enjoyment. Now it’s time to consider how you can maximize the fun and
excitement your equipment offers. This manufacturer and the Electronic Industries
Association’s Consumer Electronics Group want you to get the most out of your equipment
by playing it at a safe level: one that lets the sound come through loud and clear without
annoying blaring or distortion, and most importantly, without affecting your
sensitive hearing.
Sound can be deceiving. Over time your hearing “comfort level” adapts to higher volumes
of sound, so what sounds “normal” can actually be loud and harmful to your hearing. Guard
against this by setting your equipment at a safe level BEFORE your hearing adapts.
To establish a safe level:
• Start your volume control at a low setting.
• Slowly increase the sound until you can hear it comfortably, clearly, and
without distortion.
Once you have established a comfortable sound level:
• Set the dial and leave it there.
Taking a minute to do this now will help to prevent hearing damage or loss in the future.
After all, we want you listening for a lifetime.
We Want You Listening For A Lifetime
Used wisely, your new sound equipment will provide a lifetime of fun and enjoyment. Since
hearing damage from loud noise is often undetectable until it is too late, this manufacturer
and the Electronic Industries Association’s Consumer Electronics Group recommend you
avoid prolonged exposure to excessive noise. This list of sound levels is included for
your protection.
Decibel
Level Example
30 Quiet library, soft whispers
40 Living room, refrigerator, bedroom away from traffic
50 Light traffic, normal conversation, quiet office
60 Air conditioner at 20 feet, sewing machine
70 Vacuum cleaner, hair dryer, noisy restaurant
80 Average city traffic, garbage disposals, alarm clock at two feet
THE FOLLOWING NOISES CAN BE DANGEROUS UNDER
CONSTANT EXPOSURE:
90 Subway, motorcycle, truck traffic, lawn mower
100 Garbage truck, chain saw, pneumatic drill
120 Rock band concert in front of speakers, thunderclap
140 Gunshot blast, jet engine
180 Rocket launching pad
Information courtesy of the Deafness Research Foundation.
A
S
S
O
C
I
A
T
I
O
N
EST. 1924
E
L
E
C
T
R
O
N
I
C
I
N
D
U
S
T
R
I
E
S
EIA
We
LISTENING
For A Lifetime
Want You

4
Before using the unit, be sure to read all
operating instructions carefully. Please note
that these are general precautions and may
not pertain to your unit. For example, this unit
may not have the capability to be connected
to an outdoor antenna.
1. READ INSTRUCTIONS
All the safety and operating instructions
should be read before the product
is operated.
2. RETAIN INSTRUCTIONS
The safety and operating instructions should be
retained for future reference.
3. HEED WARNINGS
All warnings on the product and in the oper-
ating instructions should be adhered to.
4. FOLLOW INSTRUCTIONS
All operating and use instructions should
be followed.
5. CLEANING
Unplug this product from the wall outlet
before cleaning. Do not use liquid cleaners or
aerosol cleaners. Use a dry cloth for cleaning.
6. ATTACH ENTS
Do not use attachments not recommended
by the product's manufacturer as they may
cause hazards.
7. WATER AND OISTURE
Do not use this product near water–for
example: near a bathtub, washbowl, kitchen
sink or laundry tub; in a wet basement; or
near a swimming pool.
8. ACCESSORIES
Do not place this product on an unstable cart,
stand, tripod, bracket or table. The product
may fall, causing serious injury and serious
damage to the product. Use only with a cart,
stand, tripod, bracket or table recommended
by the manufacturer or sold with the product.
Any mounting of the product should follow the
manufacturer’s instructions, and should use a
mounting accessory recommended by
the manufacturer.
8A. An appliance and cart combination should be
moved with care. Quick stops, excessive
force and uneven surfaces may cause the
appliance and cart combination to overturn.
9. VENTILATION
Slots and openings in the cabinet and in the
back or bottom are provided for ventilation, to
ensure reliable operation of the product and
to protect it from overheating. These
openings must not be blocked or covered.
The openings should never be blocked by
placing the product on a bed, sofa, rug or
other similar surface. This product should
never be placed near or over a radiator or
heat source. This product should not be
placed in a built-in installation such as a
bookcase or rack unless proper ventilation is
provided or the manufacturer's instructions
have been adhered to.
10. POWER SOURCES
This product should be operated only from
the type of power source indicated on the
marking label. If you are not sure of the type
of power supply to your home, consult your
appliance dealer or local power company. For
products intended to operate from battery
power, or other sources, refer to the
operating instructions.
11. GROUNDING OR POLARIZATION
This product is equipped with a polarized
alternating-current line plug (a plug having
one blade wider than the other). This plug will
fit into the power outlet only one way. This is
a safety feature. If you are unable to insert
the plug fully into the outlet, try reversing the
plug. If the plug should still fail to fit, contact
your electrician to replace your obsolete
outlet. Do not defeat the safety purpose of the
polarized plug.
12. POWER-CORD PROTECTION
Power-supply cords should be routed so that
they are not likely to be walked on or pinched
by items placed upon or against them, paying
particular attention to cords at plugs,
convenience receptacles, and the point
where they exit from the appliance.
13. LIGHTNING
To protect your product from a lightning
storm, or when it is left unattended and
unused for long periods of time, unplug it
from the wall outlet and disconnect the
antenna or cable system. This will prevent
damage to the product due to lightning and
power-line surges.
14. POWER LINES
An outside antenna system should not be
located in the vicinity of overhead power lines
or other electric light or power circuits, or
where it can fall into such power lines or
circuits. When installing an outside antenna
system, extreme care should be taken to
I PORTANT SAFETY INSTRUCTION

5
keep from touching such power lines or
circuits as contact with them might be fatal.
15. OVERLOADING
Do not overload wall outlets and extension
cords as this can result in a risk of fire or
electric shock.
16. OBJECT AND LIQUID ENTRY
Never push objects of any kind into this product
through openings as they may touch dangerous
voltage points or short out parts that could result
in fire or electric shock. Never spill or spray any
type of liquid on the product.
17. OUTDOOR ANTENNA GROUNDING
If an outside antenna is connected to the
product, be sure the antenna system is
grounded so as to provide some protection
against voltage surges and built-up static
charges. Section 810 of the National Electric
Code, ANSI/NFPA 70, provides information
with respect to proper grounding of the mast
and supporting structure, grounding of the
lead-in wire to an antenna discharge product,
size of grounding conductors, location of
antenna discharge product, connection to
grounding electrodes and requirements for
grounding electrodes.
18. SERVICING
Do not attempt to service this product
yourself as opening or removing covers may
expose you to dangerous voltage or other
hazards. Refer all servicing to qualified
service personnel.
19. REPLACE ENT PARTS
When replacement parts are required, be
sure the service technician uses replacement
parts specified by the manufacturer or those
that have the same characteristics as the
original part. Unauthorized substitutions may
result in fire, electric shock, or other hazards.
20. SAFETY CHECK
Upon completion of any service or repairs to
this product, ask the service technician to
perform safety checks to determine that the
product is in proper operating condition.
21. WALL OR CEILING OUNTING
The product should be mounted to a wall or
ceiling only as recommended by
the manufacturer.
22. DA AGE REQUIRING SERVICE
Unplug the product from the wall outlet and
refer servicing to qualified service personnel
under the following conditions:
a. When the power-supply cord or plug is
damaged.
b. If liquid has been spilled or objects have
fallen into the product.
c. If the product has been exposed to rain or
water.
d. If the product does not operate normally
by following the operating instructions.
Adjust only those controls that are
covered by the operating instructions, as
an adjustment of other controls may result
in damage and will often require
extensive work by a qualified technician
to restore the product to its normal
operation.
e. If the product has been dropped or the
cabinet has been damaged.
f. When the product exhibits a distinct
change in performance–this indicates a
need for service.
23. HEAT
The product should be situated away from
heat sources such as radiators, heat
registers, stoves, or other products (including
amplifiers) that produce heat.
24. NOTE TO CATV SYSTE INSTALLER
This reminder is provided to call the CATV
system installer's attention to Article 820-40
of the NEC that provides guidelines for
proper grounding and, in particular, specifies
that the cable ground shall be connected to
the grounding system of the building, as
close to the point of cable entry as practical.
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE
I PORTANT SAFETY INSTRUCTION

6
LOCATION OF CONTROLS
2
1
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
1. REPEAT/Mem Down
Button
2. VOLUME Up/Down Buttons
3. STANDBY/Power button
4. Headphones ack
5. EQ Button
6. FUNCTION Button
7. SLEEP Button
8. LCD Display
9. RADIO Indicator
10. CD Indicator
11. iPod Indicator
12. Left Speaker
13. iPod Dock with Connector,
Dock Adapter & Inter-
changeable Docks
14. STOP/BAND (X) Button
15. Tune/Skip/Search o/n
Buttons
16. CD OPEN/CLOSE Button
17. PLAY/PAUSE (®p)/Mem
Up Button
18. Clock Set/Memory Button
19. iPod/AUX Button
20. Right Speaker
21. CD Door
22. CD Compartment (Under
CD Door)
23. Remote Sensor
24. Stand
FRONT/TOP

7
LOCATION OF CONTROLS (CONTINUED)
1
3
2
4
5
6
1. Carrying Handle
2. AUX OUT ack
3. AUX IN ack
4. FM Wire Antenna
5. AC Cord
6. Battery Compartment (Bottom of Unit)
(PART NO. G T207-100010)*
*Consumer Replaceable Part (See page 33 to order.)
REAR

8
LOCATION OF CONTROLS (CONTINUED)
2
1
4
3
6
5
8
7
10
9
12
11
14
13
16
15
18
17
20
19
22
21
23
F
1. MUTE Button
2. STANDBY/Power Button
3. MENU/Prog/Memory/
Clock Set Button
4. DISPLAY Button
5. Tune/Skip/Search o
Button
6. SHUFFLE Button
7. TIMER Button
8. SLEEP Button
9. ALBUM Up/Down
Buttons
10. CHAPTER Up/Down
Buttons
11. STOP/BAND (X) Button
12. REPEAT/Mem Down
13. iPod/Aux Button
14. CD OPEN/CLOSE
Button
15. MENU Up Button
16. Function Button
17. SELECT Button
18. Tune/Skip/Search n
Button
19. MENU Down Button
20. EQ Button
21. PLAYLIST Up/Down
Button
22. VOLUME Up/Down
Buttons
23. PLAY/PAUSE
(®p)/Mem Up Button
RE OTE
NOTE: The remote buttons function
in the same way as the buttons on
the main unit.
RE OTE CONTROL PART NO.
G T207-1000001*
*Consumer Replaceable Part (See page
33 to order.)

Two (2) “AA” size batteries can also be used
to provide a backup for the clock, timer
times, and the presets as follows:
1. Open the battery door on the bottom of
the unit by pushing in on the tab, then
removing the door.
2. Insert two (2) “AA” batteries as shown.
Alkaline batteries are recommended for
the longest playing time.
3. Place the battery door back on the compartment.
NOTE: The batteries are used to back-up the clock, timer times, and
presets when the AC cord is disconnected or there is a power failure.
I PORTANT! See BATTERY PRECAUTIONS on the next page.
9
POWER SOURCE
INSERTING THE BATTERIES
AC CONNECTION
Unwind the AC cord and extend it to its full
length. Insert the AC plug into any
convenient 120V 60Hz household outlet.
Please note that this unit is equipped with a
polarized AC plug which has one blade wider
than the other. This is a safety feature to
reduce the likelihood of electric shock. This
polarized AC plug will only fit in a polarized
AC outlet. If you find that you cannot insert
this plug into your outlet, you may have an
obsolete non-polarized outlet. Please do not
try to defeat this safety feature by using a non-polarized adapter or by filing the wider
blade to make it fit into your outlet. If this plug does not fit into your outlet, you should
contact a qualified licensed electrician to replace your obsolete outlet.
I PORTANT NOTE: If there is a power failure or the AC cord is disconnected for a
short period of time, the clock will stop, but the time and radio presets will be saved.
When the power is resumed or the AC cord is connected again, the clock time will
continue running and the radio presets will have been saved. However, if the power
failure lasts or the AC cord is disconnected long enough for the battery to weaken
too much, the clock will be reset and you will need to set the clock and radio presets
again.
AC Plug
AC Outlet

10
POWER SOURCE (CONTINUED)
RE OTE BATTERY INSTALLATION
BATTERY PRECAUTIONS
Follow these precautions when using batteries in this device:
1. Warning–Danger of explosion if battery is incorrectly replaced. Replace only
with the same or equivalent type.
2. Use only the size and type of batteries specified.
3. Be sure to follow the correct polarity when installing the batteries as indicated
in the Battery Compartment. A reversed battery may cause damage to
the device.
4. Do not mix different types of batteries together (e.g. Alkaline, Rechargeable,
and Carbon-zinc) or old batteries with fresh ones.
5. If the device is not to be used for a long period of time, remove the batteries
to prevent damage or injury from possible battery leakage.
6. Do not try to recharge a battery not intended to be recharged; it can overheat
and rupture. (Follow battery manufacturer’s directions.)
1. Remove the Battery Compartment by
pressing in on the tab and then sliding the
compartment out.
2. Install a CR2025 battery, by popping it in
through the back of the compartment,
paying attention to the polarity diagram in
the compartment (positive side up).
3. Replace the Battery Compartment.

11
OPTIONAL CONNECTIONS
AUX IN JACK (REAR OF UNIT)
Insert one end of the audio cable (not included) into the LINE
OUT jack on your external audio unit and the other end into the
AUX IN jack on the rear of this unit.
To listen to the external audio unit, turn this unit on using the
STANDBY/Power button, and turn on the external unit as well.
Press the iPod/AUX button to select AUX IN mode; the iPod
indicator will appear in the display. The external audio unit’s
output sound will be heard through this unit’s speakers.
NOTE: It is suggested that the audio cable be unplugged when
not listening to the external audio unit.
AUX OUT JACK (REAR OF UNIT)
Insert one end of the audio cable (not included) into the LINE IN
jack on your external audio unit and the other end into the AUX
OUT jack on the rear of this unit. Play this unit as described in
the manual and the sound will be heard through the extrernal
unit’s speakers.
HEADPHONES JACK
For private listening, connect 3.5mm (32 ohm) stereo
headphones (not included) to this jack. The speakers are
automatically disconnected when the headphone plug is inserted
in the jack.

12
With the power off, press and hold
the Clock Set/Memory button until
“12” or “24” Hour blinks in the
display.
1
Press the Tune/Skip/Search o1
or Up n2button to set the
current hour. (If you selected 12
hour mode, be sure to observe
the AM or PM indicators to make
sure you have set the hour
correctly.) Press the Clock
Set/Memory button 3again; the
minute digits will blink.
3
2
1
3
Press the Tune/Skip/Search o1
or Up n2button to set the
current minute. Press the Clock
Set/Memory button 3and the
time will blink four times and will
be set.
3
2
1
4
TO SET OR RESET THE ACTUAL TI E
Press the Tune/Skip/Search o1
or Up n2button to set the unit to
the 24 hour mode (also known as
military time) or 12
hour mode. Press the Clock
Set/Memory button 3and the
hours will blink.
3
2
1
2
NOTES:
• The time will appear in the display when the unit is turned off.
• Press the DISPLAY button to view the time.
OPERATION

13
OPERATION (CONTINUED)
To adjust the main volume:
Press the VOLUME Up 1and/or
Down 2button to increase and/or
decrease the volume.
21
1
ADJUSTING THE VOLU E AND EQ (Equalizer)
To mute the sound, press the
MUTE button once; “MUTE” will
blink in the display. Press again
to restore the volume; “MUTE”
will disappear from the display.
F
1
UTING THE SOUND
NOTES:
• After you have adjusted the
volume setting, if you turn the
unit off and then on again, the
volume level will be set to the
level you selected prior to
turning the unit off.
• For private listening, plug in
headphones into the
Headphones jack on the rear
of this unit. The speakers will
be disconnected when
headphones are plugged in.
• To turn this unit off, press the
STANDBY/Power button
To adjust the EQ (Equalizer):
Press the EQ button to cycle
through the following options:
ROCK, CLASSIC, AZZ, POP or
Normal (without indicator).
2

14
OPERATION (CONTINUED)
Locate the correct iPod dock to
use as shown on pages 28-29.
Insert the dock (A) into the iPod
compartment (as shown), making
sure the dock’s two tabs are
facing front, and slip the tabs into
place.
(A)
1
The iPod will charge until it is full.
Please see the next page for
instructions on using an iPod with
this unit.
3
Insert the iPod (A) onto the
connector (as shown). Gently
push down so the connector on
the iPod slides onto the
connector on this unit. Push the
iPod compartment back in gently.
(A) (B)
2
NOTES:
• When the iPod is connected to
this unit, it will be in the
Pause mode.
• To remove the Dock, insert your
finger (or other object) into the
gap in the Dock, then gently pull
the Dock out to remove it.
•CHARGING: When the iPod is
inserted into the dock, whether
this unit is on or off, the iPod’s
battery will charge until it is full.
• For the iPod nano 1st
generation, make sure to slide
the connector to the left before
inserting the included dock
(No.8).
INSERTING AN iPod

15
OPERATION (CONTINUED)
If this unit is not already on, turn
this unit on by pressing the
STANDBY/Power button 1. With
an iPod connected (see previous
page), press the iPod/AUX button
2to select iPod mode; the iPod
indicator will light and the music
will playback automatically.
2
1
1
You can operate the iPod using
its own controls, as per its
owner’s manual, or you can use
the controls on this unit to
operate the iPod.
2
USING AN iPod WITH THIS UNIT
To play/pause the iPod:
Press the PLAY/PAUSE (®p)/
Mem Up button to start playback
on your iPod. Press again to
pause playback, and press yet
again to resume playback.
3
To skip forward or backward on
the iPod: Press the Tune/
Skip/Search o 1 or n2button to
skip to the beginning of the current
track/previous or next track.
To search forward or backward
on the iPod: Press and hold the
Tune/Skip/Search o 1 or n 2
button to search within the
currently-playing track.
2
1
4
NOTES: See page 13 for how to adjust the volume.

OPERATION (CONTINUED)
16
With an iPod inserted, press the
REPEAT/Mem Down button to
cycle through the following iPod
Repeat modes: Repeat One (will
playback the current track
continuously or Repeat All (will
playback all tracks on the iPod
continuously).
1
When the Repeat mode is
selected, press the PLAY/PAUSE
(®p)/Mem Up button.
NOTE: To stop Repeat playback,
press the STOP/Band(X) button.
To cancel Repeat playback, press
the REPEAT button until the
Repeat indicators disappear from
the iPod’s display.
2
REPEAT PLAYBACK
To randomly play the tracks on
the iPod, with an iPod inserted,
press the SHUFFLE button on
the remote; Random playback will
begin automatically and the
Shuffle indicator will appear in the
iPod’s display.
F
1
To stop Random playback, press
the STOP/Band (X) button 1. To
cancel Random playback, press
the SHUFFLE button; the Shuffle
idicator will disappear from the
display.
F
2
1
2
RANDO PLAYBACK

OPERATION (CONTINUED)
17
While playing back an iPod, use
the ALBUM and PLAYLIST
Up/Down buttons as follows
ALBU : Press the ALBUM Up 1
or Down 2button to select a
desired album; the iPod will go to
the next or previous Album.
1
2
1
PLAYLIST: Press the PLAYLIST
Up 1or Down 2button to select
a desired playlist; the iPod will go
to the next or previous Playlist.
NOTE: You must have more than
one playlist.
1
2
2
ALBU AND PLAYLIST
While listening to an Audio-book,
press the CHAPTER Up 1or
Down 2button to select a desired
chapter; the iPod will go to the
next or previous Chapter.
F
1
2
1
CHAPTER
The MENU/Prog/Memory/Clock
Set button 1operates just like the
MENU button on the iPod. Press
the MENU Up 2/Down 3buttons
to move the menu option up or
down and the SELECT button 4
to select on the iPod’s display.
F
1
4
2
3
1
iPod ENUS
NOTES: When listening to an Audiobook, the controls on the remote
control will operate as per the controls on the iPod.

18
OPERATION (CONTINUED)
USING THE RADIO
Turn this unit on by pressing the
STANDBY/Power button 1.
Repeatedly press the FUNCTION
button 2to select the Radio mode;
the RADIO indicator will light.
12
1
Repeatedly press the STOP/
BAND (X) button to select AM or
FM mode; “AM” or “FM” will
appear in the display.
2
Repeatedly press the Tune/
Skip/Search o 1 or n2button
to manually advance the
frequency in the display up or
down until the desired frequency
appears.
For auto tuning, press and hold
the Tune/Skip/Search o 1 or n
2button until the frequency in the
display starts to scan and then
release; the tuner will search and
then stop on the next strong
station it finds. Repeat this step
until the desired frequency
appears in the display.
2
1
3NOTES:
• When set to FM, and a strong
FM Stereo station is received,
“ST” will appear in the display.
• See the previous page for how
to adjust the volume and set the
EQ.
• To turn this unit off, press the
STANDBY/Power button.
• Press the DISPLAY button on
the remote to show the time on
the display for a few seconds.
Antennas
FM: Unravel and extend the FM
wire antenna for best reception.
AM: Turn the unit for better AM
reception.

19
OPERATION (CONTINUED)
Follow Steps 1-3 on the previous
page to tune a station. Press and
hold the Clock Set/Memory
button; “P” and the preset number
will blink in the display.
1
Press the Tune/Skip/Search o 1
or n2button to select a desired
Preset (1-10). Press the Clock
Set/Memory 3again to confirm,
the station will be saved into
memory. Repeat to program up to
10 Presets, as desired.
3
2
1
2
SETTING THE RADIO PRESETS (10 for each band)
Follow Steps 1-2 on the previous
page to turn the unit on and select
AM or FM mode.
1
Press the REPEAT/Mem Down
button 1to decrease or the PLAY/
PAUSE (®p)/Mem Up button 2to
increase the preset number until
the desired Preset number appears
in the display.
12
2
RETRIEVING RADIO PRESETS (10 for each band)
NOTE: The preset memories will be erased if the unit is without power (no
batteries/AC cord isn't connected/power failure) for a long period of time.

OPERATION (CONTINUED)
20
Turn this unit on by pressing the
STANDBY/Power button 1; the
display’s backlight will light blue.
If you are not already in CD
mode, press the FUNCTION
button 2to select CD mode; the
CD indicator will light.
12
1
Press the OPEN/CLOSE button and
gently press a CD onto the center
spindle with the label side facing
you. Close the CD compartment.
The total number of tracks will
appear in the display.
NOTE: 3 inch single, standard CDs
and, CD-R/RWs discs can be used
with this unit.
2
USING A CD WITH THIS UNIT
Press the PLAY/PAUSE (®p)/
Mem Up button to begin playback;
the current track will appear in the
display.
3
When the disc is through playing,
it will stop. Press the STOP/Band
(X) button to stop the disc before it
is finished.
4