Mestek R(B User manual

Form 43343350
Oct 2013
INSTALLATION AND OPERATION INSTRUCTIONS
OWNER / INSTALLER: For your afety thi manual mu t be carefully and thoroughly read and
under tood before in talling, operating or ervicing thi heater.
INFRARED RADIANT TUBE HEATER
Single and Two Stage Pu h Through Sy tem (Po itive Pre ure)
Model :
R (B,S,M) S SERIES: (040, 050, 075, 100, 125, 150, 175, 200) – N1/L1/N2/L2
R (B,S,M) U SERIES: (040, 050, 075, 100, 125, 150, 175, 200) – N1/L1/N2/L2
!
INSTALLER
:
Thi manual i the property of the owne
r. Plea e pre ent thi manual to the
owner when you leave the job ite.
▲WARNING: Improper in tallation, adju tment, alteration, ervice, or maintenance can
cau e property damage, injury or death. Read the in tallation, operation and maintenance
in truction thoroughly before in talling or ervicing thi equipment.
IF YOU SMELL GAS: FOR YOUR SAFETY
FOR YOUR SAFETYFOR YOUR SAFETY
FOR YOUR SAFETY
!
!!
!
DO NOT
DO NOTDO NOT
DO NOT try to light any appliance.
!
!!
!DO NOT
DO NOTDO NOT
DO NOT touch any electrical witch; DO NOT
DO NOTDO NOT
DO NOT u e any
telephone in your building.
!
!!
!IMMEDIATELY
IMMEDIATELYIMMEDIATELY
IMMEDIATELY call your ga upplier from a neighbor'
telephone. Follow the ga upplier' in truction . If you
cannot reach your ga upplier, call the fire department.
DO NOT
DO NOT DO NOT
DO NOT tore or u e ga oline or other
tore or u e ga oline or other tore or u e ga oline or other
tore or u e ga oline or other
flammable vapor and liquid in the vicinity of
flammable vapor and liquid in the vicinity of flammable vapor and liquid in the vicinity of
flammable vapor and liquid in the vicinity of
thi or any other appliance.
thi or any other appliance.thi or any other appliance.
thi or any other appliance.
!IMPORTANT:
!IMPORTANT:!IMPORTANT:
!IMPORTANT: SAVE THIS MANUAL FOR FUTURE REFERENCE.
SAVE THIS MANUAL FOR FUTURE REFERENCE.SAVE THIS MANUAL FOR FUTURE REFERENCE.
SAVE THIS MANUAL FOR FUTURE REFERENCE.
Me tek, Inc.
Me tek, Inc.Me tek, Inc.
Me tek, Inc.
260 North Elm St. • We tfield, MA 01085
Telephone [phone] • Fax [phone] • www.me tek.com

Form 43343350
Oct 2013 -1-
TABLE OF CONTENTS
SECTION DESCRIPTION PAGE
1.0) Safety ................................................................................................................................................... 2
2.0) In taller Re pon ibility ...................................................................................................................... 2
3.0) General Information........................................................................................................................... 2
4.0) Minimum Clearance to Combu tible ........................................................................................... 4
5.0) Specification ...................................................................................................................................... 5
6.0) Packing Li t ......................................................................................................................................... 5
6.1) Acce ory Package ........................................................................................................................ 11
7.0) Typical Layout – Straight and U Serie ....................................................................................... 13
7.1) Typical A embly Layout – Straight Serie Shown ..................................................................... 14
8.0) Dimen ion – Straight Serie ......................................................................................................... 15
8.1) Dimen ion – U Serie .................................................................................................................... 16
8.2) Heater A embly / Joining of Tube Section ............................................................................... 17
9.0) Typical Su pen ion Method .......................................................................................................... 19
10.0) A embly of Tube Section ............................................................................................................. 20
10.1) A embly of Exten ion Section ...................................................................................................... 21
10.2) In erting Turbulator ........................................................................................................................ 22
10.3) Adding Body Reflector ................................................................................................................... 23
11.0) Adding Optional 90º Elbow - Straight Serie Only ....................................................................... 24
11.1) Adding Optional Corner Reflector - Straight Serie Only ............................................................ 24
11.2) Adding 180º U-Bend - U Serie Only .............................................................................................. 25
11.3) Adding Optional U-Bend Reflector - U Serie Only....................................................................... 25
12.0) Attaching Burner Screen – 200M BTU Model Only ................................................................... 26
12.1) Attaching Burner Box A embly..................................................................................................... 27
12.2) Connecting the TISS Sy tem .......................................................................................................... 28
13.0) Ga Connection and Regulation ................................................................................................. 31
14.0) In truction for Pre ure Te t Gauge Connection ....................................................................... 33
15.0) Electrical Thermo tat Connection ................................................................................................ 35
16.0) Venting ............................................................................................................................................... 41
17.0) Air for Combu tion ........................................................................................................................... 45
17.1) Direct Out ide Air for Combu tion ................................................................................................. 45
18.0) Lighting and Shutdown In truction .............................................................................................. 47
19.0) Sequence of Operation .................................................................................................................... 47
20.0) Control Component Location .......................................................................................................... 48
21.0) Cleaning and Annual Maintenance ............................................................................................... 49
22.0) Trouble hooting Guide..................................................................................................................... 50
23.0) Replacing Part ................................................................................................................................ 53
23.1) Removal of Main Burner and Electrode ...................................................................................... 53
23.2) Removing Ga Valve and Manifold A embly ............................................................................. 54
23.3) Air Switch Pre ure Check .............................................................................................................. 54
23.4) Ignition Sy tem Check ................................................................................................................... 55
24.0) In tallation Data ............................................................................................................................... 56
25.0) Replacement Part Guide ............................................................................................................... 57
26.0) Warning Card .................................................................................................................................. 61
Thi heater complie with ANSI Z83.20 (current tandard) and CSA 2.34. Copie of the National Fuel Ga Code (ANSI
Z223.1-late t edition) are available from the CSA at 8501 Ea t Plea ant Valley Road, Cleveland, Ohio 44131 or 55 Scar dale
Road, Don Mill , Ontario M3B 2R3. All NFPA code are available from the National Fire Protection A ociation, Batterymarch
Park, Quincy, Ma achu ett 02269.

Form 43343350
-2- Oct 2013
1.0) SAFETY
Thi heater i a elf-contained infrared radiant tube heater. Safety information required during in tallation and
operation of thi heater i provided in thi manual and the label on the product. The in tallation, ervice and
maintenance of thi heater mu t be performed by a contractor qualified in the in tallation and ervice of ga
fired heating equipment.
All per onnel in contact with the heater mu t read and under tand all afety information, in truction and label
before operation. The following ymbol will be u ed in thi manual to indicate important afety information.
Warning
WarningWarning
Warning in truc
tion mu t be followed to prevent or avoid hazard which
may cau e eriou injury, property damage or death.
Caution
CautionCaution
Caution
in truction mu t be followed to prevent incorrect operation or
in tallation of
the heater which may cau e minor injury or property
damage.
2.0) INSTALLER RESPONSIBILITY
The in taller i re pon ible for the following:
•
••
•The heater and venting, a well a electrical and ga upplie mu t be in talled in accordance with the e
in tallation in truction and any applicable code and regulation .
•
••
•Every heater hall be located with re pect to building con truction and other equipment o a to permit
acce to the heater.
•
••
•Each in taller mu t follow the clearance to combu tible material for the heater .
•
••
•In tall the heater o that the upport and hanger are correctly paced in accordance with the e
in truction . The heater mu t be upported by material having a working load limit of at lea t 115lb .
•
••
•En ure that the tube integrity afety y tem TISS™ upplied i in talled in accordance with the e in truction
and that the ten ion i correct.
•
••
•Supply the owner with a copy of the e In tallation and Operation In truction .
•
••
•Where unvented heater are u ed, gravity or mechanical mean hall be provided to upply and exhau t at
lea t 4 CFM per 1,000 Btu/hr input of in talled heater .
•
••
•Never u e the heater a a upport for a ladder or other acce equipment. Do not hang anything from the
heater.
•
••
•Supply all in tallation material nece ary that are not included with the heater.
•
••
•Check the nameplate to make ure that the burner i correct for the ga type in the building and the
in tallation altitude.
3.0) GENERAL INFORMATION
Thi heater i a elf-contained infrared radiant tube heater for u e in location where flammable ga e or vapor
are not generally pre ent (a defined by OSHA acceptable limit ) and i intended for the heating of
nonre idential
nonre identialnonre idential
nonre idential pace .
INSTALLATION REQUIREMENTS
INSTALLATION REQUIREMENTSINSTALLATION REQUIREMENTS
INSTALLATION REQUIREMENTS
The in tallation mu t conform to local building code or in the ab ence of local code , with the National Fuel Ga
Code ANSI Z223.1/NFPA54 or the Natural Ga and Propane In tallation Code CSA B149.1. Heater hall be
in talled by a licen ed contractor or licen ed in taller. Clearance to combu tible a outlined in thi manual
hould alway be ob erved. In area u ed for torage of combu tible material where they may be tacked
below the heater, NFPA54 require that the in taller mu t po t ign that will “ pecify the maximum permi ible
tacking height to maintain the required clearance from the heater to combu tible .”
Every heater hall be located with re pect to building con truction and other equipment o a to permit acce
to the heater. Each in taller hall u e quality in tallation practice when locating the heater and mu t give
con ideration to clearance to combu tible material , vehicle parked below, light , overhead door , torage
area with tacked material , prinkler head , ga and electrical line and any other po ible ob truction or
hazard . Con ideration al o mu t be given to ervice acce ibility.

Form 43343350
Oct 2013 -3-
The heater, when in talled in aircraft hangar and public garage , mu t be in talled in accordance with
ANSI/NFPA 409-late t edition (Standard for Aircraft Hangar ), ANSI/NFPA 88a-late t edition (Standard for
Parking Structure ), and ANSI/NFPA 88b-late t edition (Standard for Repair Garage ) with the following
clearance :
a. At lea t 10 feet above the upper urface of wing or engine enclo ure of the highe t aircraft that may be
hou ed in the hangar and at lea t 8 feet above the floor in hop , office , and other ection of hangar
communicating with aircraft torage or ervice area .
b. At lea t 8 feet above the floor in public garage . ▲
▲▲
▲WARNING:
WARNING:WARNING:
WARNING: Minimum clearance marked on the heater
mu t be maintained from vehicle parked below the heater.
(FOR CANADA ONLY)
a.
In tallation of t
hi appliance i to be in accordance with late t edition of C
SA
B149.1 (
Natural Ga and
Propane In tallation Code).
b. For in tallation in public garage or aircraft hangar , the minimum clearance from the bottom of the
infrared heater to the upper urface of the highe t aircraft or vehicle hall be 50 percent greater than the
certified minimum clearance, but the clearance hall not be le than 8 feet.
Although the e heater may be u ed in many application other than pace heating (e.g., proce heating),
Me tek, Inc. will not recognize the warranty for any u e other than pace heating.
For indoor in tallation only. Not for u e in re idential dwelling .
For indoor in tallation only. Not for u e in re idential dwelling .For indoor in tallation only. Not for u e in re idential dwelling .
For indoor in tallation only. Not for u e in re idential dwelling .
Thi heater i for Indoor In tallation and Covered Patio In tallation only and can be u ed in either Vented or
Unvented mode. The term Unvented actually mean Indirect Vented. While the product of combu tion are
expelled into the building, national code require ventilation in the building to dilute the e product of
combu tion. Thi ventilation may be provided by gravity or mechanical mean .
Thi heater i not an explo ion proof heater.
Thi heater i not an explo ion proof heater.Thi heater i not an explo ion proof heater.
Thi heater i not an explo ion proof heater. Where the po ibility of expo ure to volatile and low fla h point
material exi t , it could re ult in property damage or death. Thi heater mu t not be in talled in a pray booth
where the heater can operate during the praying proce . Con ult your local fire mar hal or in urance company.
R(B,S,M) S
R(B,S,M) SR(B,S,M) S
R(B,S,M) S Serie Only:
Serie Only:Serie Only:
Serie Only: Since traight tube heater are alway hotter at the control end than at the flue terminal
Since traight tube heater are alway hotter at the control end than at the flue terminal Since traight tube heater are alway hotter at the control end than at the flue terminal
Since traight tube heater are alway hotter at the control end than at the flue terminal
end, alway ob erve t
end, alway ob erve tend, alway ob erve t
end, alway ob erve the minimum recommended mounting height hown on the pecification heet
he minimum recommended mounting height hown on the pecification heethe minimum recommended mounting height hown on the pecification heet
he minimum recommended mounting height hown on the pecification heet and in
Section 5.0) of thi manual. U e U-tube configuration in tead of traight tube for pot or area heating (e.g.,
where a ingle heater i utilized for pace heating).
WARM
HOT WARM
WARM
WARM
HOT
High Altitude:
High Altitude:High Altitude:
High Altitude:
Appliance are upplied a tandard for altitude of O to 2,000 feet (0-610 m). High-altitude rating are obtained
by a change in the orifice ize. When ordered for high altitude in tallation , burner are upplied by the factory
ready for high altitude in tallation. Check the nameplate for altitude before proceeding with the in tallation. In
Canada the adju tment for altitude i made in accordance with Standard CGA 2.17, Ga -Fired Appliance for U e
at High Altitude .

Form 43343350
-4- Oct 2013
4.0) MINIMUM CLEARANCES TO COMBUSTIBLES
Failure to do so may result in death, serious injury or
property damage.
Combustible material must be located outside the
clearance dimensions listed.
In tall the warning card (ordered eparately) and complete the blank pace u ing the clearance from
combu tible table below. See Section 26 for a printed copy of the warning card.
Minimum clearance to combu tible hall be mea ured from the outer urface a hown in the following
diagram:
End End
Ceiling
Below
Front
Rear
45° Angle (Maximum)
* Ceiling
Below
Side Side
Horizontal
MINIMUM CLEARANCES TO COMBUSTIBLES
MINIMUM CLEARANCES TO COMBUSTIBLESMINIMUM CLEARANCES TO COMBUSTIBLES
MINIMUM CLEARANCES TO COMBUSTIBLES
Model No.
Model No.Model No.
Model No.
Mounted Horizontally
Mounted HorizontallyMounted Horizontally
Mounted Horizontally
Angle Mounted at
Angle Mounted at Angle Mounted at
Angle Mounted at
45º
45º45º
45º
Side
SideSide
Side Ceiling*
Ceiling*Ceiling*
Ceiling* Below
BelowBelow
Below End
EndEnd
End 45º Front
45º Front45º Front
45º Front 45º Rear
45º Rear45º Rear
45º Rear
R(B,S,M) S/U 0
40
22
”
6”
52
”
15
”
40
”
1
2”
R(B,S,M) S/U 0
50
22
”
6”
56
”
15
”
48”
12”
R(B,S,M) S/U 0
75
22
”
6”
60”
15
”
52
”
12”
R(B,S,M) S/U 100 28” 6” 70” ** 15” 58” 12”
R(B,S,M) S/U 125 28” 6” 76” ** 20” 66” 12”
R(B,S,M) S/U
150
34
”
6”
81
” **
20
”
70
”
12
”
R(B,S,M) S/U
175
38
”
6”
86
” **
20
”
75
”
12
”
R(B,S,M) S/U
200
42
”
6”
93
” **
20
”
80
”
12
”
* When u ed indirect vented, minimum clearance for CEILING mu t be: 12” for R(B,S,M) S/U 050-075 and 18”
for R(B,S,M) S/U 100-200. If optional corner and u-bend reflector are not u ed, the clearance mu t be 18”.
** Maximum clearance below reduce by 50% once you are 25ft. down tream from the burner box.
▲WARNING:
▲WARNING:▲WARNING:
▲WARNING: Certain material or object , when tored under the heater, will be ubjected to radiant heat and
Certain material or object , when tored under the heater, will be ubjected to radiant heat and Certain material or object , when tored under the heater, will be ubjected to radiant heat and
Certain material or object , when tored under the heater, will be ubjected to radiant heat and
could be eriou ly damaged. Ob erve the Minimum Clearance to Combu tible li ted in the manual and on the
could be eriou ly damaged. Ob erve the Minimum Clearance to Combu tible li ted in the manual and on the could be eriou ly damaged. Ob erve the Minimum Clearance to Combu tible li ted in the manual and on the
could be eriou ly damaged. Ob erve the Minimum Clearance to Combu tible li ted in the manual and on the
heater at all time .
heater at all time .heater at all time .
heater at all time .
NOTE:
NOTE:NOTE:
NOTE:
1.
1. 1.
1. The clear
The clearThe clear
The clearance pecified above mu t be maintained to combu tible and other material that may be
ance pecified above mu t be maintained to combu tible and other material that may be ance pecified above mu t be maintained to combu tible and other material that may be
ance pecified above mu t be maintained to combu tible and other material that may be
damaged by temperature 90ºF above ambient temperature. Clearance to combu tible are po ted on the
damaged by temperature 90ºF above ambient temperature. Clearance to combu tible are po ted on the damaged by temperature 90ºF above ambient temperature. Clearance to combu tible are po ted on the
damaged by temperature 90ºF above ambient temperature. Clearance to combu tible are po ted on the
burner
burnerburner
burner box. In area u ed for torage of combu tible material w
box. In area u ed for torage of combu tible material wbox. In area u ed for torage of combu tible material w
box. In area u ed for torage of combu tible material where they may be tacked below the heater,
here they may be tacked below the heater, here they may be tacked below the heater,
here they may be tacked below the heater,
NFPA54 require that the in taller mu t po t ign that will “ pecify the maximum permi ible tacking height
NFPA54 require that the in taller mu t po t ign that will “ pecify the maximum permi ible tacking height NFPA54 require that the in taller mu t po t ign that will “ pecify the maximum permi ible tacking height
NFPA54 require that the in taller mu t po t ign that will “ pecify the maximum permi ible tacking height
to maintain the required clearance from the heater to combu tible .”
to maintain the required clearance from the heater to combu tible .” to maintain the required clearance from the heater to combu tible .”
to maintain the required clearance from the heater to combu tible .” Me tek, Inc.
Me tek, Inc.Me tek, Inc.
Me tek, Inc. recommend
recommendrecommend
recommend po ting
po ting po ting
po ting the e
the e the e
the e
ign adjacent to the heater thermo tat or other uitable location that will provide enhanced vi ibility.
ign adjacent to the heater thermo tat or other uitable location that will provide enhanced vi ibility.ign adjacent to the heater thermo tat or other uitable location that will provide enhanced vi ibility.
ign adjacent to the heater thermo tat or other uitable location that will provide enhanced vi ibility.
2.
2. 2.
2. The tated clearance to combu tible repre ent a urface temperature of 90 ºF (32 ºC) above room
The tated clearance to combu tible repre ent a urface temperature of 90 ºF (32 ºC) above room The tated clearance to combu tible repre ent a urface temperature of 90 ºF (32 ºC) above room
The tated clearance to combu tible repre ent a urface temperature of 90 ºF (32 ºC) above room
temperature. Building material with a low
temperature. Building material with a low temperature. Building material with a low
temperature. Building material with a low heat tolerance ( uch a pla tic , vinyle iding, canva , tri
heat tolerance ( uch a pla tic , vinyle iding, canva , triheat tolerance ( uch a pla tic , vinyle iding, canva , tri
heat tolerance ( uch a pla tic , vinyle iding, canva , tri-
--
-ply, etc.)
ply, etc.) ply, etc.)
ply, etc.)
may be ubject to degradation at lower temperature . It i the in taller’ re pon ibility to a ure that adjacent
may be ubject to degradation at lower temperature . It i the in taller’ re pon ibility to a ure that adjacent may be ubject to degradation at lower temperature . It i the in taller’ re pon ibility to a ure that adjacent
may be ubject to degradation at lower temperature . It i the in taller’ re pon ibility to a ure that adjacent
material are protected from degradation.
material are protected from degradation.material are protected from degradation.
material are protected from degradation.

Form 43343350
Oct 2013 -5-
5.0) SPECIFICATIONS
Model No.
Model No.Model No.
Model No.
Bt
BtBt
Btu/hr
u/hru/hr
u/hr
Input
InputInput
Input
Combu tion
Combu tion Combu tion
Combu tion
Air Plate
Air PlateAir Plate
Air Plate
Part #
Part #Part #
Part #
Orifice Size
Orifice SizeOrifice Size
Orifice Size
Minimum *
Minimum *Minimum *
Minimum *
Mounting Height
Mounting HeightMounting Height
Mounting Height
Turbulator
Turbulator Turbulator
Turbulator
Qty.
Qty.Qty.
Qty. Natural Ga
Natural GaNatural Ga
Natural Ga Propane Ga
Propane GaPropane Ga
Propane Ga
@
@@
@
Horizontal
HorizontalHorizontal
Horizontal
@
@@
@
45º Angle
45º Angle45º Angle
45º Angle
R(B,S,M) S/U 040
40,000
#44140061
#32
(0.116)
#49
(0.073)
10 ft.
9 ft.
4
R(B,S,M) S/U 050
50,000
#4414006
4
3.5mm
(0.138)
46
(0.081)
11 ft.
10 ft.
5
R(B,S,M) S/U 075
75,000
#44140063
#21
(0.159)
2.5mm
(0.098)
13 ft.
12 ft.
5
R(B,S,M) S/U 100 100,000 #44140062 #12 (0.189) #32 (0.116) 14 ft. 13 ft. 3
R(B,S,M) S/U 125 125,000 #44140066 #4 (0.209) #30 (0.129) 14 ft. 13 ft. 7
R(B,S,M) S/U 150 150,000 #44140067 “A” (0.234) #27 (0.144) 15 ft. 14 ft. 4
R(B,S,M) S/U 175
175,000
#44140067
“E”
(0.250)
#23
(0.154)
16 ft.
15 ft.
0
R(B,S,M) S/U 200
200,000
#44140068
6.9mm
(0.272)
4.1mm
(0.161)
18 ft.
16 ft.
1
* MOUNT HEATERS AS HIGH AS POSSIBLE. Minimum are hown a a guideline for human comfort and uniform
energy di tribution for complete building heating application . Con ult your Me tek, Inc. repre entative for the
particular of your in tallation requirement .
Ty
TyTy
Ty
pe
pepe
pe
Ga
GaGa
Ga
Ga Pipe
Ga PipeGa Pipe
Ga Pipe
Connection
Connection Connection
Connection
Tube
TubeTube
Tube
Diameter
DiameterDiameter
Diameter
Flue
FlueFlue
Flue
Connection
ConnectionConnection
Connection1
11
1
Fre h Air
Fre h Air Fre h Air
Fre h Air
Connection
ConnectionConnection
Connection1
11
1
Electrical
ElectricalElectrical
Electrical
Supply
SupplySupply
Supply
Current
CurrentCurrent
Current
Rating
RatingRating
Rating
Natural
or Propane
½” MPT
(Male) 4” 4” Round 4” Round
120 Volt,
60Hz,
1 Pha e 1.74 Amp
1 See Section 16.0) for vent ize when multiple heater are connected into a common vent
Module Electrical Rating:
Module Electrical Rating:Module Electrical Rating:
Module Electrical Rating: Ignition Sy tem (direct park):
Ignition Sy tem (direct park):Ignition Sy tem (direct park):
Ignition Sy tem (direct park):
Input Power
-
Control: 18
-
30 VAC 50/60 Hz (cla 2
tran former)
Input Power-Line: 120 VAC (L1, IND contact only)
Ga Valve Rating: 2.0 A @ 24 VAC (max.)
Combu tion Blower Rating: 3.0 FLA @ 120 VAC
0.0233 H.P. Motor
Flame Sen itivity: 0.7 microamp minimum
15 econd trial for ignition period
15 econd pre-purge period
60 econd inter-purge period
30 econd po t-purge period
3 trie for ignition ( eparate flame en or).
6.0) PACKING LIST
A.
A.A.
A. R(B,S,M) S/U
R(B,S,M) S/UR(B,S,M) S/U
R(B,S,M) S/U Burner Package
Burner PackageBurner Package
Burner Package
Part De cription
Part De criptionPart De cription
Part De cription
QTY
QTYQTY
QTY
Burner Box A embly (Refer to the following chart for Package Part Number )
..........................
1
4”ID x 4”Lg
Flue Adapter Collar (#30504500)
................................
................................
..................
1
Fa tener Kit
–
Burner Box Attachment/Flue Adapter Collar (#42907040)
................................
..
1
Containing:
#10 x 1/2” Self
-
Drilling Screw (#02189020)
................................
....................
2
¼
-
20 Locknut (#02167010)
................................
................................
..............
3
Tube Flange Ga ket
(#42921000)
................................
................................
...........
1
Turbulat
or 24” Long (#44152240) *See chart above for required quantitie .
..............................
*
In tallation & Operation In truction
................................
................................
................................
....
1
Turnbuckle
(#30545040)
................................
................................
................................
.........................
1
Ga connector 5/8” OD x 36”
(#30302360)
................................
................................
........................
1
Screen A embly – 2-5/8” ID x 5-1/2” Long (#44151010) 200M B
200M B200M B
200M BTU model only
TU model onlyTU model only
TU model only ................... 1
End Reflector Package (#43341000) .................................................................................................. 1

Form 43343350
-6- Oct 2013
BURNER PACKAGE NUMB
BURNER PACKAGE NUMBBURNER PACKAGE NUMB
BURNER PACKAGE NUMBERS
ERSERS
ERS
1
11
1
-
--
-
STAGE CONTROLS
STAGE CONTROLSSTAGE CONTROLS
STAGE CONTROLS
-
--
-
MESTEK
MESTEKMESTEK
MESTEK
2
22
2
-
--
-
STAGE CONTROLS
STAGE CONTROLSSTAGE CONTROLS
STAGE CONTROLS
-
--
-
MESTEK
MESTEKMESTEK
MESTEK
MODEL NO.
MODEL NO.MODEL NO.
MODEL NO. PART NO.
PART NO.PART NO.
PART NO. GAS TYPE
GAS TYPEGAS TYPE
GAS TYPE MODEL NO.
MODEL NO.MODEL NO.
MODEL NO. PART NO.
PART NO.PART NO.
PART NO. GAS TYPE
GAS TYPEGAS TYPE
GAS TYPE
RMS/U040N1U0
44490010
NATURAL
RMS/U040N2U0
44490510
NATUR
AL
RMS/U050N1U0
44490030
NATURAL
RMS/U050N2U0
44490530
NATURAL
RMS/U075N1U0
44490050
NATURAL
RMS/U075N2U0
44490550
NATURAL
RMS/U100N1U0
44490070
NATURAL
RMS/U100N2U0
44490570
NATURAL
RMS/U125N1U0
44490090
NATURAL
RMS/U125N2U0
44490590
NATURAL
RMS/
U150N1U0
44490110
NATURAL
RMS/U150N2U0
44490610
NATURAL
RMS/U175N1U0
44490130
NATURAL
RMS/U175N2U0
44490630
NATURAL
RMS/U200N1U0
44490150
NATURAL
RMS/U200N2U0
44490650
NATURAL
RMS/U040L1U0
44490020
PROPANE
RMS/U040L2U0
44490520
PROPANE
RMS/U050L1U0
44490040
PROPANE
RMS/U050L2U0
44490540
PROPANE
RMS/U075L1U0
44490060
PROPANE
RMS/U075L2U0
44490560
PROPANE
RMS/U100L1U0
44490080
PROPANE
RMS/U100L2U0
44490580
PROPANE
RMS/U125L1U0
44490100
PROPANE
RMS/U125L2U0
44490600
PROPANE
RMS/U150L1U0
4449012
0
PROPANE
RMS/U150L2U0
44490620
PROPANE
RMS/U175L1U0
44490140
PROPANE
RMS/U175L2U0
44490640
PROPANE
RMS/U200L1U0
44490160
PROPANE
RMS/U200L2U0
44490660
PROPANE
1
11
1
-
--
-
STAGE CONTROLS
STAGE CONTROLS STAGE CONTROLS
STAGE CONTROLS
-
--
-
STERLING
STERLINGSTERLING
STERLING
2
22
2
-
--
-
STAGE CONTROLS
STAGE CONTROLS STAGE CONTROLS
STAGE CONTROLS
-
--
-
STERLING
STERLINGSTERLING
STERLING
MODEL NO.
MODEL NO.MODEL NO.
MODEL NO. PART NO.
PART NO.PART NO.
PART NO. GAS TYPE
GAS TYPEGAS TYPE
GAS TYPE MODEL NO.
MODEL NO.MODEL NO.
MODEL NO. PART NO.
PART NO.PART NO.
PART NO. GAS TYPE
GAS TYPEGAS TYPE
GAS TYPE
RSS/U040N1U0
44488010
NATURAL
RSS/U040N2U0
44488510
NATURAL
RSS/U050N1U0
44488030
NATURAL
RSS/U050N2U0
44488530
NATURAL
RSS/U075N1U0
44488050
NATURAL
RSS/U075N2U0
44488550
NATURAL
RSS/U100N1U0
44488070
NATURAL
RSS/U100
N2U0
44488570
NATURAL
RSS/U125N1U0
44488090
NATURAL
RSS/U125N2U0
44488590
NATURAL
RSS/U150N1U0
44488110
NATURAL
RSS/U150N2U0
44488610
NATURAL
RSS/U175N1U0
44488130
NATURAL
RSS/U175N2U0
44488630
NATURAL
RSS/U200N1U0
44488150
NATURAL
RSS/U200N2U0
444
88650
NATURAL
RSS/U040L1U0
44488020
PROPANE
RSS/U040L2U0
44488520
PROPANE
RSS/U050L1U0
44488040
PROPANE
RSS/U050L2U0
44488540
PROPANE
RSS/U075L1U0
44488060
PROPANE
RSS/U075L2U0
44488560
PROPANE
RSS/U100L1U0
44488080
PROPANE
RSS/U100L2U0
44488580
PR
OPANE
RSS/U125L1U0
44488100
PROPANE
RSS/U125L2U0
44488600
PROPANE
RSS/U150L1U0
44488120
PROPANE
RSS/U150L2U0
44488620
PROPANE
RSS/U175L1U0
44488140
PROPANE
RSS/U175L2U0
44488640
PROPANE
RSS/U200L1U0
44488160
PROPANE
RSS/U200L2U0
44488660
PROPANE

Form 43343350
Oct 2013 -7-
1
11
1
-
--
-
STAGE CONTROLS
STAGE CONTROLS STAGE CONTROLS
STAGE CONTROLS
–
––
–
BEACON/MORRIS
BEACON/MORRISBEACON/MORRIS
BEACON/MORRIS
2
22
2
-
--
-
STAGE CONTROLS
STAGE CONTROLS STAGE CONTROLS
STAGE CONTROLS
–
––
–
BEACON/MORRIS
BEACON/MORRISBEACON/MORRIS
BEACON/MORRIS
MODEL NO.
MODEL NO.MODEL NO.
MODEL NO. PART NO.
PART NO.PART NO.
PART NO. GAS TYPE
GAS TYPEGAS TYPE
GAS TYPE MODEL NO.
MODEL NO.MODEL NO.
MODEL NO. PART NO.
PART NO.PART NO.
PART NO. GAS TYPE
GAS TYPEGAS TYPE
GAS TYPE
RBS/U040N1U0
44492010
NATURAL
RBS/U040N2U0
44492510
NATURAL
RBS/U050N1U0
44492030
NATURAL
RBS/U050N2U0
4449253
0
NATURAL
RBS/U075N1U0
44492050
NATURAL
RBS/U075N2U0
44492550
NATURAL
RBS/U100N1U0
44492070
NATURAL
RBS/U100N2U0
44492570
NATURAL
RBS/U125N1U0
44492090
NATURAL
RBS/U125N2U0
44492590
NATURAL
RBS/U150N1U0
44492110
NATURAL
RBS/U150N2U0
44492610
NATURA
L
RBS/U175N1U0
44492130
NATURAL
RBS/U175N2U0
44492630
NATURAL
RBS/U200N1U0
44492150
NATURAL
RBS/U200N2U0
44492650
NATURAL
RBS/U040L1U0
44492020
PROPANE
RBS/U040L2U0
44492520
PROPANE
RBS/U050L1U0
44492040
PROPANE
RBS/U050L2U0
44492540
PROPANE
RBS/U
075L1U0
44492060
PROPANE
RBS/U075L2U0
44492560
PROPANE
RBS/U100L1U0
44492080
PROPANE
RBS/U100L2U0
44492580
PROPANE
RBS/U125L1U0
44492100
PROPANE
RBS/U125L2U0
44492600
PROPANE
RBS/U150L1U0
44492120
PROPANE
RBS/U150L2U0
44492620
PROPANE
RBS/U175L1U0
44492140
PROPANE
RBS/U175L2U0
44492640
PROPANE
RBS/U200L1U0
44492160
PROPANE
RBS/U200L2U0
44492660
PROPANE
B.
B.B.
B. R(B,S,M) S 0
R(B,S,M) S 0R(B,S,M) S 0
R(B,S,M) S 040
4040
40-
--
-200 Body Package De cription
200 Body Package De cription200 Body Package De cription
200 Body Package De cription
(Package Part Number is indicated on the outside of each corresponding carton.)
Sy tem
Sy temSy tem
Sy tem
1
11
1
0Ft.
0Ft. 0Ft.
0Ft.
Sy
SySy
Sy tem
temtem
tem
2
22
2
0Ft.
0Ft. 0Ft.
0Ft.
Sy tem
Sy temSy tem
Sy tem
3
33
3
0Ft.
0Ft. 0Ft.
0Ft.
Sy tem
Sy temSy tem
Sy tem
4
44
4
0Ft.
0Ft. 0Ft.
0Ft.
Sy tem
Sy temSy tem
Sy tem
5
55
5
0Ft.
0Ft. 0Ft.
0Ft.
Sy tem
Sy temSy tem
Sy tem
R(B,S,M) S
R(B,S,M) SR(B,S,M) S
R(B,S,M) S Body Package
Body Package Body Package
Body Package –
––
– Aluminized/Hot Rolled or
Aluminized/Hot Rolled orAluminized/Hot Rolled or
Aluminized/Hot Rolled or
Alumi
AlumiAlumi
Alumi-
--
-Therm/Hot Rolled
Therm/Hot Rolled Therm/Hot Rolled
Therm/Hot Rolled
10 Ft.
10 Ft.10 Ft.
10 Ft. pkg
pkgpkg
pkg
44134020
4413402044134020
44134020
20 Ft. pkg
20 Ft. pkg20 Ft. pkg
20 Ft. pkg
44135000
4413500044135000
44135000
30 Ft. pkg
30 Ft. pkg30 Ft. pkg
30 Ft. pkg
44136000
4413600044136000
44136000
40 Ft. pkg
40 Ft. pkg 40 Ft. pkg
40 Ft. pkg
44137100
4413710044137100
44137100
50 Ft
50 Ft50 Ft
50 Ft. pkg
. pkg. pkg
. pkg
44138100
4413810044138100
44138100
Part #
Part #Part #
Part # Each Body Package Include :
Each Body Package Include :Each Body Package Include :
Each Body Package Include : Qty.
Qty.Qty.
Qty. Qty.
Qty.Qty.
Qty. Qty.
Qty.Qty.
Qty. Qty.
Qty.Qty.
Qty. Qty.
Qty.Qty.
Qty.
429121
80
10 Ft. Tube with 12
Hole Flange (Aluminized)
1
1
1
-
-
42912169
10 Ft. Tube with 6 Hole Flange (Alumi
-
Therm)
-
-
-
1
1
41932101
10 Ft. Tube le Flange (Hot Rolled)
-
1
2
3
4
43319100
Reflector, 9’ 11½”
1
2
3
4
5
30462980
Tube Coupling
-
1
2
3
4
43318000
Tube Hanger/Support Bracket, 13”
1
2
3
4
5
43980010
Wire Hanger
1
2
3
4
5
Body Fa tener Kit (included in body package )
Body Fa tener Kit (included in body package )Body Fa tener Kit (included in body package )
Body Fa tener Kit (included in body package ) 42907280
4290728042907280
42907280 42907190
4290719042907190
42907190 42907200
4290720042907200
42907200 42907210
4290721042907210
42907210 42907
4290742907
42907220
220220
220
42873000
U
-
Bolt
1
2
3
4
5
02127110
Hex Nut, 5/16
-
18
3
5
6
8
10
02189020
HWHSM Screw, #10
-
16 x ½” TEKS
4
8
10
14
18

Form 43343350
-8- Oct 2013
Sy tem
Sy temSy tem
Sy tem
60Ft. Sy tem
60Ft. Sy tem60Ft. Sy tem
60Ft. Sy tem
70Ft. Sy tem
70Ft. Sy tem70Ft. Sy tem
70Ft. Sy tem
R(B,S,M) S
R(B,S,M) SR(B,S,M) S
R(B,S,M) S Body Package
Body Package Body Package
Body Package –
––
– Alumi
AlumiAlumi
Alumi-
--
-Therm/Hot Rolled
Therm/Hot RolledTherm/Hot Rolled
Therm/Hot Rolled
40 Ft. Pkg
40 Ft. Pkg40 Ft. Pkg
40 Ft. Pkg
44137100
4413710044137100
44137100
20 Ft. Pkg
20 Ft. Pkg20 Ft. Pkg
20 Ft. Pkg
4413
44134413
44135010
50105010
5010
40 Ft. Pkg.
40 Ft. Pkg.40 Ft. Pkg.
40 Ft. Pkg.
44137100
4413710044137100
44137100
30 Ft. Pkg
30 Ft. Pkg30 Ft. Pkg
30 Ft. Pkg
44136040
4413604044136040
44136040
Part #
Part #Part #
Part # Each Body Package Include :
Each Body Package Include :Each Body Package Include :
Each Body Package Include : Qty.
Qty.Qty.
Qty. Qty.
Qty.Qty.
Qty. Qty.
Qty.Qty.
Qty. Qty.
Qty.Qty.
Qty.
42912169
10 Ft. Tube with 6 Hole Flange (Alumi
-
Therm)
1
-
1
-
41932101
10 Ft. Tube le Flange (Hot Rolled)
3
2
3
3
43319100
Reflector, 9’ 11½”
4
2
4
3
30462980
Tube Coupling
3
2
3
3
43318000
Tube Hanger/Support Bracket, 13”
4
2
4
3
43980010
Wire Hanger
4
2
4
3
Body Fa tener Kit (included in body package )
Body Fa tener Kit (included in body package )Body Fa tener Kit (included in body package )
Body Fa tener Kit (included in body package ) 42907210
4290721042907210
42907210 42907190
4290719042907190
42907190 42907210
4290721042907210
42907210 42907200
4290720042907200
42907200
42873000 U-Bolt 4 2 4 3
02127110 Hex Nut, 5/16-18 8 5 8 6
02189020
HWHSM Screw, #10
-
16 x ½” TEKS
14
8
14
10
C.
C.C.
C. R(B,S,M) S
R(B,S,M) SR(B,S,M) S
R(B,S,M) S 40
4040
40-
--
-200 Serie Body Package De cription
200 Serie Body Package De cription 200 Serie Body Package De cription
200 Serie Body Package De cription –
––
– ALC Option (Aluminized Heat Treated
ALC Option (Aluminized Heat TreatedALC Option (Aluminized Heat Treated
ALC Option (Aluminized Heat Treated)
))
)
(Package Part Number is indicated on the outside of each corresponding carton.)
Sy tem
Sy temSy tem
Sy tem
1
11
1
0Ft.
0Ft.0Ft.
0Ft.
Sy tem
Sy temSy tem
Sy tem
2
22
2
0Ft.
0Ft. 0Ft.
0Ft.
Sy tem
Sy temSy tem
Sy tem
3
33
3
0Ft.
0Ft. 0Ft.
0Ft.
Sy tem
Sy temSy tem
Sy tem
4
44
4
0Ft.
0Ft. 0Ft.
0Ft.
Sy tem
Sy temSy tem
Sy tem
5
55
5
0Ft.
0Ft. 0Ft.
0Ft.
Sy tem
Sy temSy tem
Sy tem
R(B,S,M) S
R(B,S,M) SR(B,S,M) S
R(B,S,M) S Body Package
Body Package Body Package
Body Package –
––
– Aluminized/
Aluminized/Aluminized/
Aluminized/ Aluminized
AluminizedAluminized
Aluminized or
oror
or
Alumi
AlumiAlumi
Alumi-
--
-Therm/
Therm/Therm/
Therm/ Aluminized
AluminizedAluminized
Aluminized
10 Ft.
10 Ft.10 Ft.
10 Ft. pkg
pkgpkg
pkg
44134020
4413402044134020
44134020
20 Ft. pkg
20 Ft. pkg20 Ft. pkg
20 Ft. pkg
44135020
4413502044135020
44135020
30 Ft. pkg
30 Ft. pkg30 Ft. pkg
30 Ft. pkg
44136020
4413602044136020
44136020
40 Ft. pkg
40 Ft. pkg 40 Ft. pkg
40 Ft. pkg
44137090
4413709044137090
44137090
50 Ft. pkg
50 Ft. pkg50 Ft. pkg
50 Ft. pkg
44138080
4413808044138080
44138080
Part #
Part #Part #
Part # Each Body Package Include :
Each Body Package Include :Each Body Package Include :
Each Body Package Include : Qty.
Qty.Qty.
Qty. Qty.
Qty.Qty.
Qty. Qty.
Qty.Qty.
Qty. Qty.
Qty.Qty.
Qty. Qty.
Qty.Qty.
Qty.
429121
80
10 Ft. Tube with 12
Hole Flange (Aluminized)
1
1
1
-
-
42912169
10 Ft. Tube with 6 Hole Flange (Alumi
-
Therm)
-
-
-
1
1
41932100
10 Ft. Tube le Flange (Aluminiz
ed)
-
1
2
3
4
43319100
Reflector, 9’ 11½”
1
2
3
4
5
30462980
Tube Coupling
-
1
2
3
4
43318000
Tube Hanger/Support Bracket, 13”
1
2
3
4
5
43980010
Wire Hanger
1
2
3
4
5
Body Fa tener Kit (included in body package )
Body Fa tener Kit (included in body package )Body Fa tener Kit (included in body package )
Body Fa tener Kit (included in body package ) 42907280
4290728042907280
42907280 42907190
4290719042907190
42907190 42907200
4290720042907200
42907200 42907210
4290721042907210
42907210 42907220
4290722042907220
42907220
42873000
U
-
Bolt
1
2
3
4
5
02127110
Hex Nut, 5/16
-
18
3
5
6
8
10
02189020
HWHSM Screw, #10
-
16 x ½” TEKS
4
8
10
14
18
Sy tem
Sy temSy tem
Sy tem
60Ft. Sy tem
60Ft. Sy tem60Ft. Sy tem
60Ft. Sy tem
70Ft. Sy tem
70Ft. Sy tem70Ft. Sy tem
70Ft. Sy tem
R(B,S,M) S
R(B,S,M) SR(B,S,M) S
R(B,S,M) S Body Package
Body Package Body Package
Body Package –
––
– Alumi
AlumiAlumi
Alumi-
--
-Therm/
Therm/Therm/
Therm/ Aluminized
AluminizedAluminized
Aluminized
40 Ft. Pkg
40 Ft. Pkg40 Ft. Pkg
40 Ft. Pkg
44137090
4413709044137090
44137090
20 Ft. Pkg
20 Ft. Pkg20 Ft. Pkg
20 Ft. Pkg
44135030
4413503044135030
44135030
40 Ft. Pkg.
40 Ft. Pkg.40 Ft. Pkg.
40 Ft. Pkg.
44137090
4413709044137090
44137090
30 Ft. Pkg
30 Ft. Pkg30 Ft. Pkg
30 Ft. Pkg
44136050
4413605044136050
44136050
Part #
Part #Part #
Part # Each Body Package Include :
Each Body Package Include :Each Body Package Include :
Each Body Package Include : Qty.
Qty.Qty.
Qty. Qty.
Qty.Qty.
Qty. Qty.
Qty.Qty.
Qty. Qty.
Qty.Qty.
Qty.
42912169
10 Ft. Tube with 6 Hole Flange (Alumi
-
Therm)
1
-
1
-
4193210
0
10 Ft. Tube le Flange (Aluminized)
3
2
3
3
43319100
Reflector, 9’ 11½”
4
2
4
3
30462980
Tube Coupling
3
2
3
3
43318000
Tube Hanger/Support Bracket, 13”
4
2
4
3
43980010
Wire Hanger
4
2
4
3
Body Fa tener Kit (included in body package )
Body Fa tener Kit (included in body package )Body Fa tener Kit (included in body package )
Body Fa tener Kit (included in body package ) 42907210
4290721042907210
42907210 42907190
4290719042907190
42907190 42907210
4290721042907210
42907210 42907200
4290720042907200
42907200
42873000 U-Bolt 4 2 4 3
02127110 Hex Nut, 5/16-18 8 5 8 6
02189020
HWHSM Screw, #10
-
16 x ½” TEKS
14
8
14
10

Form 43343350
Oct 2013 -9-
D.
D.D.
D. R(B,S,M) U
R(B,S,M) UR(B,S,M) U
R(B,S,M) U 0
00
040
4040
40-
--
-200 Body Package De cription
200 Body Package De cription200 Body Package De cription
200 Body Package De cription
(Package Part Number is indicated on the outside of each corresponding carton.)
Sy tem
Sy temSy tem
Sy tem
2
22
2
0Ft.
0Ft. 0Ft.
0Ft.
Sy tem
Sy temSy tem
Sy tem
3
33
3
0Ft.
0Ft. 0Ft.
0Ft.
Sy tem
Sy temSy tem
Sy tem
4
44
4
0Ft.
0Ft. 0Ft.
0Ft.
Sy tem
Sy temSy tem
Sy tem
5
55
5
0Ft.
0Ft. 0Ft.
0Ft.
Sy tem
Sy temSy tem
Sy tem
R
RR
R(B,S,M) U
(B,S,M) U(B,S,M) U
(B,S,M) U Body Package
Body Package Body Package
Body Package –
––
– Aluminized/Hot Rolled or
Aluminized/Hot Rolled orAluminized/Hot Rolled or
Aluminized/Hot Rolled or
Alumi
AlumiAlumi
Alumi-
--
-Therm/Hot Rolled
Therm/Hot Rolled Therm/Hot Rolled
Therm/Hot Rolled
20 Ft.
20 Ft.20 Ft.
20 Ft. pkg
pkgpkg
pkg
44135000
4413500044135000
44135000
30 Ft. pkg
30 Ft. pkg30 Ft. pkg
30 Ft. pkg
44136010
4413601044136010
44136010
40 Ft. pkg
40 Ft. pkg 40 Ft. pkg
40 Ft. pkg
44137100
4413710044137100
44137100
50 Ft. pkg
50 Ft. pkg50 Ft. pkg
50 Ft. pkg
44138110
4413811044138110
44138110
Part #
Part #Part #
Part # Each Body Package Include :
Each Body Package Include :Each Body Package Include :
Each Body Package Include : Qty.
Qty.Qty.
Qty. Qty.
Qty.Qty.
Qty. Qty.
Qty.Qty.
Qty. Qty.
Qty.Qty.
Qty.
429121
80
1
0 Ft. Tube with 12
Hole Flange (Aluminized)
1
1
-
-
42912169
10 Ft. Tube with 6 Hole Flange (Alumi
-
Therm)
-
-
1
1
41932101
10 Ft. Tube le Flange (Hot Rolled)
1
1
3
3
41932051
5 Ft. Tube le Flange (Hot Rolled)
-
2
-
2
43319100
Reflector, 9’
11½”
2
2
4
4
43319050
Reflector, 4’ 11½”
-
2
-
2
30462980
Tube Coupling
1
3
3
5
43318000
Tube Hanger/Support Bracket, 13”
2
4
4
6
43980010
Wire Hanger
2
4
4
6
Body Fa tener Kit (included in body package )
Body Fa tener Kit (included in body package )Body Fa tener Kit (included in body package )
Body Fa tener Kit (included in body package ) 42907190
4290719042907190
42907190 42907210
4290721042907210
42907210 42907210
4290721042907210
42907210 42907221
4290722142907221
42907221
42873
000
U
-
Bolt
2
4
4
6
02127110
Hex Nut, 5/16
-
18
5
8
8
1
3
02189020
HWHSM Screw, #10
-
16 x ½” TEKS
8
1
4
14
24
U
UU
U-
--
-Bend Package
Bend PackageBend Package
Bend Package 43208020
4320802043208020
43208020 43208020
4320802043208020
43208020 43208020
4320802043208020
43208020 43208020
4320802043208020
43208020
42913020
U
-
Bend
1
1
1
1
43318500
31” Tube Support/Hanger Bracket
1
1
1
1
30462980
Tube Coupl
ing
1
1
1
1
02189020
HWHSM Screw, #10
-
16 x ½” TEKS
2
2
2
2
Sy tem
Sy temSy tem
Sy tem
60Ft. Sy tem
60Ft. Sy tem60Ft. Sy tem
60Ft. Sy tem
70Ft. Sy tem
70Ft. Sy tem70Ft. Sy tem
70Ft. Sy tem
R(B,S,M) U
R(B,S,M) UR(B,S,M) U
R(B,S,M) U Body Package
Body Package Body Package
Body Package –
––
– Alumi
AlumiAlumi
Alumi-
--
-Therm/Hot Rolled
Therm/Hot RolledTherm/Hot Rolled
Therm/Hot Rolled
40 Ft. Pkg
40 Ft. Pkg40 Ft. Pkg
40 Ft. Pkg
44137
4413744137
4413710
1010
100
00
0
20 Ft. Pkg
20 Ft. Pkg20 Ft. Pkg
20 Ft. Pkg
441350
441350441350
4413501
11
10
00
0
40 Ft. Pkg.
40 Ft. Pkg.40 Ft. Pkg.
40 Ft. Pkg.
44137
4413744137
4413712
1212
120
00
0
30 Ft. Pkg
30 Ft. Pkg30 Ft. Pkg
30 Ft. Pkg
441360
441360441360
4413604
44
40
00
0
Part #
Part #Part #
Part # Each Body Packag
Each Body PackagEach Body Packag
Each Body Package Include :
e Include :e Include :
e Include : Qty.
Qty.Qty.
Qty. Qty.
Qty.Qty.
Qty. Qty.
Qty.Qty.
Qty. Qty.
Qty.Qty.
Qty.
42912169
10 Ft. Tube with 6 Hole Flange (Alumi
-
Therm)
1
-
1
-
4193210
1
10 Ft. Tube le Flange (
Hot Rolled
)
3
2
2
3
41932051
5 Ft. Tube le Flange (Hot Rolled)
-
-
2
-
43319100
Reflector, 9’ 11½”
4
2
3
3
433
19050
Reflector, 4’ 11½”
-
-
2
-
30462980
Tube Coupling
3
2
4
3
43318000
Tube Hanger/Support Bracket, 13”
4
2
5
3
43980010
Wire Hanger
4
2
5
3
Body Fa tener Kit (included in body package )
Body Fa tener Kit (included in body package )Body Fa tener Kit (included in body package )
Body Fa tener Kit (included in body package ) 42907210
4290721042907210
42907210 42907190
4290719042907190
42907190 429072
429072429072
4290722
22
20
00
0 42907200
4290720042907200
42907200
42873000 U-Bolt 4 2 5 3
02127110 Hex Nut, 5/16-18 8 5 10 6
02189020
HWHSM Screw, #10
-
16 x ½” TEKS
14
8
18
10
U
UU
U-
--
-Bend Package
Bend PackageBend Package
Bend Package 43208020
4320802043208020
43208020 43208020
4320802043208020
43208020
42913020 U-Bend 1 1
43318500 31” Tube Support/Hanger Bracket 1 1
30462980 Tube Coupling 1 1
02189020
HWHSM Scr
ew, #10
-
16 x ½” TEKS
2
2

Form 43343350
-10- Oct 2013
E.
E.E.
E. R(B,S,M) U
R(B,S,M) UR(B,S,M) U
R(B,S,M) U 0
00
040
4040
40-
--
-200 Serie Body Package De cription
200 Serie Body Package De cription 200 Serie Body Package De cription
200 Serie Body Package De cription –
––
– ALC Option (Aluminized Heat Treated
ALC Option (Aluminized Heat TreatedALC Option (Aluminized Heat Treated
ALC Option (Aluminized Heat Treated)
))
)
(Package Part Number is indicated on the outside of each corresponding carton.)
Sy tem
Sy temSy tem
Sy tem
2
22
2
0Ft.
0Ft. 0Ft.
0Ft.
Sy tem
Sy temSy tem
Sy tem
3
33
3
0Ft.
0Ft. 0Ft.
0Ft.
Sy tem
Sy temSy tem
Sy tem
4
44
4
0Ft.
0Ft. 0Ft.
0Ft.
Sy tem
Sy temSy tem
Sy tem
5
55
5
0Ft
0Ft0Ft
0Ft
.
. .
.
Sy tem
Sy temSy tem
Sy tem
R(B,S,M) U
R(B,S,M) UR(B,S,M) U
R(B,S,M) U Body Package
Body Package Body Package
Body Package –
––
– Aluminized/Aluminized or
Aluminized/Aluminized orAluminized/Aluminized or
Aluminized/Aluminized or
Alumi
AlumiAlumi
Alumi-
--
-Therm/Aluminized
Therm/AluminizedTherm/Aluminized
Therm/Aluminized
20 Ft.
20 Ft.20 Ft.
20 Ft. pkg
pkgpkg
pkg
44135020
4413502044135020
44135020
30 Ft. pkg
30 Ft. pkg30 Ft. pkg
30 Ft. pkg
44136030
4413603044136030
44136030
40 Ft. pkg
40 Ft. pkg 40 Ft. pkg
40 Ft. pkg
44137090
4413709044137090
44137090
50 Ft. pkg
50 Ft. pkg50 Ft. pkg
50 Ft. pkg
44138090
4413809044138090
44138090
Part #
Part #Part #
Part # Each Body Package Include :
Each Body Package Include :Each Body Package Include :
Each Body Package Include : Qty.
Qty.Qty.
Qty. Qty.
Qty.Qty.
Qty. Qty.
Qty.Qty.
Qty. Qt
QtQt
Qty.
y.y.
y.
429121
80
10 Ft. Tube with 12
Hole Flange (Aluminized)
1
1
-
-
42912169
10 Ft. Tube with 6 Hole Flange (Alumi
-
Therm)
-
-
1
1
41932100
10 Ft. Tube le Flange (Aluminized)
1
1
3
3
41932050
5 Ft. Tube le Flange (Aluminized)
-
2
-
2
43319100
Refl
ector, 9’ 11½”
2
2
4
4
43319050
Reflector, 4’ 11½”
-
2
-
2
30462980
Tube Coupling
1
3
3
5
43318000
Tube Hanger/Support Bracket, 13”
2
4
4
6
43980010
Wire Hanger
2
4
4
6
Body Fa tener Kit (included in body package )
Body Fa tener Kit (included in body package )Body Fa tener Kit (included in body package )
Body Fa tener Kit (included in body package ) 42907190
4290719042907190
42907190 42907210
4290721042907210
42907210 42907210
4290721042907210
42907210 42907
4290742907
42907221
221221
221
42873000
U
-
Bolt
2
4
4
6
02127110
Hex Nut, 5/16
-
18
5
8
8
1
3
02189020
HWHSM Screw, #10
-
16 x ½” TEKS
8
1
4
14
24
U
UU
U-
--
-Bend Package
Bend PackageBend Package
Bend Package 43208020
4320802043208020
43208020 43208020
4320802043208020
43208020 43208020
4320802043208020
43208020 43208020
4320802043208020
43208020
42913020
U
-
Bend
1
1
1
1
43318500
31” Tube Support/Hanger Bracket
1
1
1
1
30462980
Tube Coupling
1
1
1
1
02189020
HWHSM Screw, #10
-
16 x ½” TEKS
2
2
2
2
60Ft. Sy tem
60Ft. Sy tem60Ft. Sy tem
60Ft. Sy tem 70Ft. Sy tem
70Ft. Sy tem70Ft. Sy tem
70Ft. Sy tem
R(B,S,M) U
R(B,S,M) UR(B,S,M) U
R(B,S,M) U Body P
Body PBody P
Body Package
ackage ackage
ackage –
––
– Alumi
AlumiAlumi
Alumi-
--
-Therm/Aluminized
Therm/AluminizedTherm/Aluminized
Therm/Aluminized
40 Ft. Pkg
40 Ft. Pkg40 Ft. Pkg
40 Ft. Pkg
44137
4413744137
4413709
0909
090
00
0
20 Ft. Pkg
20 Ft. Pkg20 Ft. Pkg
20 Ft. Pkg
441350
441350441350
4413503
33
30
00
0
40 Ft. Pkg.
40 Ft. Pkg.40 Ft. Pkg.
40 Ft. Pkg.
441371
441371441371
4413711
11
10
00
0
30 Ft. Pkg
30 Ft. Pkg30 Ft. Pkg
30 Ft. Pkg
441360
441360441360
4413605
55
50
00
0
Part #
Part #Part #
Part # Each Body Pac
Each Body PacEach Body Pac
Each Body Package Include :
kage Include :kage Include :
kage Include : Qty.
Qty.Qty.
Qty. Qty.
Qty.Qty.
Qty. Qty.
Qty.Qty.
Qty. Qty.
Qty.Qty.
Qty.
42912169
10 Ft. Tube with 6 Hole Flange (Alumi
-
Therm)
1
-
1
-
4193210
0
10 Ft. Tube le Flange (
Aluminized
)
3
2
2
3
4193205
0
5 Ft. Tube le Flange (
Aluminized
)
-
-
2
-
43319100
Reflector, 9’ 11½”
4
2
3
3
43319050
Reflector, 4’ 11½”
-
-
2
-
30462980
Tube Coupling
3
2
4
3
43318000
Tube Hanger/Support Bracket, 13”
4
2
5
3
43980010
Wire Hanger
4
2
5
3
Body Fa tener Kit (included in body package )
Body Fa tener Kit (included in body package )Body Fa tener Kit (included in body package )
Body Fa tener Kit (included in body package ) 42907210
4290721042907210
42907210 42907190
4290719042907190
42907190 429072
429072429072
4290722
22
20
00
0 42907200
4290720042907200
42907200
42873000 U-Bolt 4 2 5 3
02127110 Hex Nut, 5/16-18 8 5 10 6
02189020
HWHSM Screw, #10
-
16 x ½” TEKS
14
8
18
10
U
UU
U-
--
-Bend Package
Bend PackageBend Package
Bend Package 43208020
4320802043208020
43208020 43208020
4320802043208020
43208020
42913020 U-Bend 1 1
43318500 31” Tube Support/Hanger Bracket 1 1
30462980 Tube Coupling 1 1
02189020
HWHSM
Screw, #10
-
16 x ½” TEKS
2
2

Form 43343350
Oct 2013 -11-
6.1) ACCESSORY PACKAGES
A.
A.A.
A.
End Reflector
End Reflector End Reflector
End Reflector
Acce ory Package, Part #4334100
Acce ory Package, Part #4334100Acce ory Package, Part #4334100
Acce ory Package, Part #4334100
0
00
0
(1 pkg. per S - Straight Series or 2 pkgs. per U - Series)
Contains:
End Reflector, #43320000……QTY–2
Speed Clip , #02266010……QTY–8
6
(15cm)
12
(30cm)
END REFLECTOR
B.
B.B.
B.
Elbow Acce ory
Elbow Acce oryElbow Acce ory
Elbow Acce ory
Package, Part #43208010
Package, Part #43208010Package, Part #43208010
Package, Part #43208010
( ption for S - Straight Series nly)
Contains:
Elbow, #43175000……QTY–1
#10-16 x ½ Self-Drilling Screw , #02189020……QTY–2
Tube Coupling, #30462980……QTY–1
13
(33cm)
13
(33cm)
C.
C.C.
C.
Corner Reflector Acce ory Package, Part #43342000
Corner Reflector Acce ory Package, Part #43342000Corner Reflector Acce ory Package, Part #43342000
Corner Reflector Acce ory Package, Part #43342000
( ption for S - Straight Series nly)
Contains:
Corner Reflector A embly, #43345000……QTY–1
Speed Clip , #02266010……QTY–4
24
(61cm)
24
(61cm)
D.
D.D.
D.
U
UU
U
-
--
-
Bend Package, Part #43208020
Bend Package, Part #43208020Bend Package, Part #43208020
Bend Package, Part #43208020
( ption for U - Series nly)
Contains:
U-Bend, #42913020……QTY–1
#10-16 x ½ Self-Drilling Screw , #02189020……QTY–2
Tube Coupling, #30462980……QTY–1
31” Tube Support/Hanger Bracket, #43318500……QTY–1
18
(46cm)

Form 43343350
-12- Oct 2013
E.
E.E.
E.
U
UU
U
-
--
-
Bend Reflector Package, Part #43488000
Bend Reflector Package, Part #43488000Bend Reflector Package, Part #43488000
Bend Reflector Package, Part #43488000
( ption for U - Series nly)
Contains:
U-Bend Reflector, #43490000……QTY–1
U-Bend End Reflector, #43490050……QTY–1
Speed Clip , #02266010……QTY–11
#10-16 x ½ Self-Drilling Screw , #02189020……QTY–4
In tallation Form, #43489000……QTY-1
30 3/4 (78cm)
Length = 24 (61cm)
F.
F.F.
F.
31” Hanger/Tube Support, Part #43318500
31” Hanger/Tube Support, Part #4331850031” Hanger/Tube Support, Part #43318500
31” Hanger/Tube Support, Part #43318500
( ption for Angle Mounting of U – Series nly)
18
(46cm)
Tube Centers
31
(79cm)
G.
G.G.
G.
Exhau t Hood Pack
Exhau t Hood PackExhau t Hood Pack
Exhau t Hood Pack
age, Part #42924000
age, Part #42924000age, Part #42924000
age, Part #42924000
Contains:
Exhau t Hood A embly, #42925550……QTY–1
#8-18 x ½ Self-Drilling Screw , #02189030……QTY–2
4 (10cm)
7 1/2
(19cm)
3 3/4 (10cm)
3 1/2 (9cm)
6
(15cm)
Bird
Screen
Side View Front View

Form 43343350
Oct 2013 -13-
7.0) TYPICAL LAYOUTS – STRAIGHT AND U SERIES
Burner Box
Flue Termination
10 FT. Body Section
30 FT.
SYSTEM
40 FT.
SYSTEM
20 FT.
SYSTEM
50 FT.
SYSTEM
60 FT.
SYSTEM
10FT.
SYSTEM
5 FT. Body Section
90 Deg. Elbow *
180 Deg. U-Bend
LEGEND
* Minimum Distance Permitted
Between Burner and 90 Elbow
R(B,S,M) S/U 040 to 100 10 FT.
R(B,S,M) S/U 125 to 175 15 FT.
R(B,S,M) S/U 200 20 FT.
70 FT.
SYSTEM
MODEL
MODELMODEL
MODEL
EMITTER LENGTH
EMITTER LENGTHEMITTER LENGTH
EMITTER LENGTH
MODEL
MODELMODEL
MODEL
BODY LENGTH
BODY LENGTHBODY LENGTH
BODY LENGTH
Min.
Min.Min.
Min.
Max.
Max.Max.
Max.
Min.
Min.Min.
Min.
Max.
Max.Max.
Max.
R
(B,S,M) S
040
10 Ft.
20 Ft.
R
(B,S,M)
U 040
10 Ft.
10 Ft.
R(B,S,M)
S
050
20 Ft
4
0 Ft.
R(B,S,M)
U 050
10 Ft.
20
Ft.
R(B,S,M) S
075
20 Ft.
4
0 Ft.
R(B,S,M)
U 075
10 Ft.
20
Ft
R(B,S,M)
S
100
30 Ft.
5
0 Ft.
R(B,S,M) U 100
15 Ft.
25
Ft.
R(B,S
,M) S
125
30 Ft
6
0 Ft.
R(B,S
,M)
U 125
1
5 Ft.
30
Ft.
R(B,S,M) S
150
40 Ft.
60 Ft.
R(B,S,M)
U 150
20 Ft.
30 Ft.
R(B,S,M) S
175
50 Ft.
70 Ft.
R(B,S,M)
U 175
25 Ft.
35 Ft.
R
(B,S,M) S
200
50 Ft.
70 Ft.
R
(B,S,M)
U 200
25 Ft.
35 Ft.
NOTES:
NOTES:NOTES:
NOTES:
1. In all configuration , the control unit mu t be connected directly to either a) the 12-radial hole flange of the
10 ft. aluminized teel tarting body ection (for 10 ft., 20 ft., and 30 ft. y tem ) or b) the 6-hole flange of
the 10 ft. alumi-therm teel tarting body ection (for 40 ft., 50 ft., 60 ft., and 70 ft. y tem ).
2. Joining of two 90º elbow directly together to form a “Z” hape IS NOT permitted.
3. 5 Ft. Body Package may be utilized on any of the e heater to yield heater length from 15 ft. to 70 ft.
4. Any configuration of component not hown in the illu tration may be u ed except a noted in 1 and 2
above.

Form 43343350
-14- Oct 2013
7.1) TYPICAL ASSEMBLY LAYOUT – STRAIGHT SERIES SHOWN
Failure to do so may result in death, serious injury, property damage or illness
from Carbon Monoxide poisoning.
The heater must be assembled with the correct number of turbulator sections
and tube length for the rated heat input.
The turbulator must be installed in the last tube section as shown.
POISONOUS GAS AND SOOT HAZARD
60 FT. SYSTEM
50 FT. SYSTEM
20 FT. SYSTEM
30 FT. SYSTEM
40 FT. SYSTEM
LEGEND
Burner Box 10ft Aluminized Tube
12 Radial Hole Flange
or
10ft Alumi-Therm Tube
6 Hole Flange
Coupling 10ft Aluminized or HRS
Tube model dependent
2ft Aluminized
Steel
Turbulator
sections
70 FT. SYSTEM
10 FT. SYSTEM
2ft Stainless
Steel
Turbulator
sections
Stainless Steel Turbulator closest
to burner R (B,S,M) S/U 040 only. Model
R(B,S,M) S/U 040
R(B,S,M) S/U 050
R(B,S,M) S/U 075
R(B,S,M) S/U 100
R(B,S,M) S/U 125
R(B,S,M) S/U 150
R(B,S,M) S/U 175
R(B,S,M) S/U 200
2 Ft. Turbulator
Sections
4
5
5
3
7
4
0
1

Form 43343350
Oct 2013 -15-
8.0) DIMENSIONS – STRAIGHT SERIES
Typical Dimen ion Up to 60 Ft. Shown.
Burner Box
13 Tube Support/ Hanger Bracket
Wire Hanger
4 Tube Coupling (typical)
Bottom View
Wire Hanger
Wire Hanger 13 Tube Support/
Hanger Bracket
13 Tube Support/ Hanger Bracket
108
(274cm)
720
(1829cm)
108
(274cm)
108
(274cm) 108
(274cm)
108
(274cm)
12
(30cm)
12
(30cm) 12
(30cm)
Wire Hanger
Wire Hanger 13 Tube Support/
Hanger Bracket
13 Tube Support/ Hanger Bracket Wire Hanger
13 Tube Support/ Hanger Bracket
108
(274cm)
12
(30cm)
12
(30cm)
4 Tube Coupling (typical)
Bottom View
108
(274cm)
600
(1524cm)
108
(274cm)
108
(274cm) 108
(274cm)
108
(274cm)
12
(30cm)
12
(30cm) 12
(30cm)
12
(30cm)
108
(274cm)
Models: R(B,S,M) S 040 - 075
14
(36cm) 108
(274cm)
240
(610cm)
12
(30cm)
108
(274cm)
480
(1219cm)
108
(274cm)
12
(30cm)
108
(274cm)
108
(274cm)
12
(30cm)
Models: R(B,S,M) S 050 - 125
360
(914cm)
108
(274cm)
12
(30cm)
12
(30cm)
108
(274cm)
108
(274cm)
Flue Terminal
10 FT Tube Assembly (typical)
Models: R(B,S,M) S 040
14
(36cm) 108
(274cm)
120
(305cm)
10
(25cm)
14-1/2
(37cm)
Fresh Air Inlet
1/2 MPT Gas Connection
9-1/4
(24cm)
End View
Flue Terminal Burner
Box
120VAC Power Supply Cord
Models: R(B,S,M) S 050 - 150
Models: R(B,S,M) S 100 - 200
Models: R(B,S,M) S 125 - 200

Form 43343350
-16- Oct 2013
8.1) DIMENSIONS – U SERIES
Typical Dimen ion Up to 50 Ft. Shown.
Models:
R(B,S,M) U 040 - 075
Models:
R(B,S,M) U 050 - 125
Models:
R(B,S,M) U 050 - 175
Models:
R(B,S,M) U 100 - 200
300
(762cm)
108
(274cm)
12
(30cm)
12
(30cm)
Bottom View
Wire Hangers
(typical)
108
(274cm)
12
(30cm)
240
(610cm) 108
(274cm)
180
(457cm) 108
(274cm)
12
(30cm)
48
(122cm)
5 FT Tube
Assembly
14
(36cm)
120
(305cm)
108
(274cm)
Burner
Box
Flue
Terminal
10 FT Tube
Assembly
(typical)
15
(38cm)
108
(274cm)
48
(122cm)
31 Tube Support/
Hanger Brackets
(typical at control end)
Shipped with
U-Bend Package
Wire Hangers
(typical)
U-Bend
13 Tube Support/
Hanger Brackets
(typical)
4 Tube Coupling
(typical)
13 Tube Support/
Hanger Brackets
(typical)
6
(16cm)
Flue Terminal 18 (46cm)
31 (79cm)
End View
Burner
Box
U-Bend
31 Tube Support/
Hanger Bracket
10
(25cm)
14-1/2
(37cm)
Fresh Air
Inlet
1/2 MPT Gas
Connection
120VAC
Power Supply Cord

Form 43343350
Oct 2013 -17-
8.2) HEATER ASSEMBLY / JOINING OF TUBE SECTIONS
Typical Assembly Overview
R
(B,S,M) S
40FT
- Straight
Shown
4"OD x 10Ft.
Tube
See section
7
for required tubes.
Tube Support Bracket
U-Bolt Clamp & 5/16" Hex Nuts
Mounting
Flange
12 Radial Hole for Aluminized Steel Tubes 6 Hole for Alumi-Therm Steel Tubes
Wire Hanger
Gasket
Burner Box
Flue Terminal
5 hanging points to be used for suspension for a typical 40ft long system. There must be two hanging points on the first tube and one on each of the other tubes
Maximum 6 distance from control box to the tube support/hanger bracket.
8 to 9 ¼
8 to 10
8 to 10
Not Less Than 10
#10 Self-Drill Screws (Typical all tube supports, tube couplings and flue terminal.)
Typical Overlap
Turbulator (See specifications section 5 for required quantities.)
Tube Coupling (Typical each tube joint
.
)
Burner Box Suspension Chain
3 (
burner
box to reflector)
2

overlap
1

overlap
1

overlap

Form 43343350
-18- Oct 2013
Typical Assembly Overview
R(B,S,M) U 40FT U-Tube Shown
Wire Hanger
Flue
Terminal
#10 Self-Drill Screws
(Typical all tube supports,
tube couplings and flue
terminal.)
4"OD x 10Ft. Tube
See section 7
for required tubes.
13 Tube Support Brk.
with U-Bolt Clamp
& 5/16" Hex Nuts
Mounting Flange
12 Radial Hole for Aluminized Steel Tubes
6 Hole for Alumi-Therm Steel Tubes
Gasket
Burner Box
Typical
Overlap
U-Bend
Tube Coupling
(Typical each tube joint.)
Reflector
31 Tube Support Brk.
with U-Bolt Clamp
& 5/16" Hex Nuts
8 - 10
6 hanging points to be used for suspension for a typical
40ft long system. There must be two hanging points
on the first tube and one on each of the other tubes
Maximum 6 distance
from burner box to the
tube support/hanger
bracket.
8 - 9 ¼
#10 Self-Drill
Screws
(2 each)
Turbulator
(See specifications
section 5 for required
quantities.)
Burner Box
Suspension
Chain

Form 43343350
Oct 2013 -19-
9.0) TYPICAL SUSPENSION METHODS
Burner must be secured to the mounting flange with nuts.
All materials used to suspend the heater must have a minimum working load
of 115 lbs.
All S Hooks must be crimped closed.
Never use the heater to support a ladder or other access equipment.
Failure to do so may result in death, serious injury or property damage.
SUSPENSION HAZARD
Variou mean of u pending the heater can be u ed. See the following drawing for typical example .
1. U e only noncombu tible material for u pending hanger and bracket .
2. A minimum No. 2 chain with a working load limit of 115 lb . i required.
3. Turnbuckle can be u ed with chain to allow leveling of the heater. All “S” hook and eye bolt mu t be
manually crimped clo ed by the in taller.
4. When u ing rigid mean for heater u pen ion (rod, flat bar, etc.) provide ufficient length or wing joint to
compen ate for expan ion. See Figure b and c.
5. Heater ubject to vibration mu t be provided with vibration i olating hanger .
6. Heater mu t not be upported by ga or electric upply line and mu t be u pended from a permanent
tructure with adequate load capacity.
Me tek, Inc. recommend that the body ection be u pended u ing chain with turnbuckle . Thi will allow
light adju tment after a embly and heater expan ion/ contraction during operation.
If a “trapeze” method i u ed for tube upport/hanger bracket ( hown below), the minimum chain length for the
two connecting chain i 36” to minimize any vibration that might be generated by the burner box. If the e
chain mu t be le than 36”, then do not u e the trapeze method and, in tead, u e individual chain on each
tube upport/hanger bracket.
Eyebolt
Turnbuckle
Minimum
No. 2 Chain
Eyebolt
c.
Threaded
Rod
Turnbuckle
Eyebolt
b.
3/16 x 1
wideFlat Bar
Minimum
No. 2 Chain
a.
S-Hook crimped
closed (typical)
Wire Hanger
Wire
Hanger
Burner Box Suspension
36 (91cm) Minimum
Tube Support/
Hanger Bracket
d.
Eye bolt
Turnbuckle
Failure to install the burner box suspension
chain will void the manufacturers warranty.