Metabo HPT DS18DSDL Troubleshooting guide

Designed for operating in USA & Canada only.
When this product is used in areas other than the USA & Canada,
we cannot guarantee the product quality and performance.
SAFETY INSTRUCTIONS AND INSTRUCTION MANUAL
WARNING
IMPROPER OR UNSAFE use of this power tool can result in death or serious bodily injury!
This manual contains important information about product safety. Please read and understand
this manual BEFORE operating the power tool. Please keep this manual available for other
users and owners before they use the power tool. This manual should be stored in safe place.
INSTRUCTIONS DE SECURITE ET MODE D’EMPLOI
AVERTISSEMENT
Une utilisation INCORRECTE OU DANGEREUSE de cet outil motorisé peut entraîner la mort
ou de sérieuses blessures corporelles!
Ce mode d’emploi contient d’importantes informations à propos de la sécurité de ce produit.
Prière de lire et de comprendre ce mode d’emploi AVANT d’utiliser l’outil motorisé. Garder ce
mode d’emploi à la disponibilité des autres utilisateurs et propriétaires avant qu’ils utilisent
l’outil motorisé. Ce mode d’emploi doit être conservé dans un endroit sûr.
INSTRUCCIONES DE SEGURIDAD Y MANUAL DE INSTRUCCIONES
ADVERTENCIA
¡La utilización INAPROPIADA O PELIGROSA de esta herramienta eléctrica puede resultar
en lesiones de gravedad o la muerte!
Este manual contiene información importante sobre la seguridad del producto. Lea y
comprenda este manual ANTES de utilizar la herramienta eléctrica. Guarde este manual para
que puedan leerlo otras personas antes de utilizar la herramienta eléctrica. Este manual debe
ser guardado en un lugar seguro.
Model
Modèle
Modelo
DS 18DSDL
DV 18DSDL
Cordless Driver Drill
Perceuse-visseuse sans fil
Taladro atornillador a batería
Cordless Hammer Drill
Perceuse à percussion sans fil
Taladro de percusión a batería
DS18DSDL DV18DSDL
000BookDS18DSDLmetabo.indb1000BookDS18DSDLmetabo.indb1 2018/11/0111:52:092018/11/0111:52:09

IMPORTANT SAFETY INFORMATION
Read and understand all of the safety precautions, warnings and operating instructions in the Instruction Manual before
operating or maintaining this power tool.
Most accidents that result from power tool operation and maintenance are caused by the failure to observe basic safety
rules or precautions. An accident can often be avoided by recognizing a potentially hazardous situation before it occurs,
and by observing appropriate safety procedures.
Basic safety precautions are outlined in the “SAFETY” section of this Instruction Manual and in the sections which
contain the operation and maintenance instructions.
Hazards that must be avoided to prevent bodily injury or machine damage are identified by WARNINGS on the power
tool and in this Instruction Manual.
NEVER use this power tool in a manner that has not been specifically recommended by metabo HPT.
MEANINGS OF SIGNAL WORDS
WARNING indicates a potentially hazardous situations which, if ignored, could result in death or serious injury.
CAUTION indicates a potentially hazardous situations which, if not avoided, may result in minor or moderate injury, or
may cause machine damage.
NOTE emphasizes essential information.
SAFETY
GENERAL POWER TOOL SAFETY WARNINGS
WARNING
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated
(cordless) power tool.
1) Work area safety
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust.
Power tools create sparks which may ignite the
dust or fumes.
c) Keep children and bystanders away while
operating a power tool.
Distractions can cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet.
Never modify the plug in any way.
Do not use any adapter plugs with earthed
(grounded) power tools.
Unmodified plugs and matching outlets will reduce
risk of electric shock.
b) Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators.
There is an increased risk of electric shock if your
body is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions.
Water entering a power tool will increase the risk
of electric shock.
d) Do not abuse the cord. Never use the cord
for carrying, pulling or unplugging the power
tool.
Keep cord away from heat, oil, sharp edges or
moving parts.
Damaged or entangled cords increase the risk of
electric shock.
e) When operating a power tool outdoors, use
an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces the
risk of electric shock.
f) If operating a power tool in a damp location
is unavoidable, use a residual current device
(RCD) protected supply.
Use of an RCD reduces the risk of electric shock.
2
English
000BookDS18DSDLmetabo.indb2000BookDS18DSDLmetabo.indb2 2018/11/0111:52:092018/11/0111:52:09

3) Personal safety
a) Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired
or under the influence of drugs, alcohol or
medication.
A moment of inattention while operating power
tools may result in serious personal injury.
b) Use personal protective equipment. Always
wear eye protection.
Protective equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protection used
for appropriate conditions will reduce personal
injuries.
c) Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool.
Carrying power tools with your finger on the switch
or energising power tools that have the switch on
invites accidents.
d) Remove any adjusting key or wrench before
turning the power tool on.
A wrench or a key left attached to a rotating part of
the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and
balance at all times.
This enables better control of the power tool in
unexpected situations.
f) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts.
Loose clothes, jewellery or long hair can be caught
in moving parts.
g) If devices are provided for the connection
of dust extraction and collection facilities,
ensure these are connected and properly
used.
Use of dust collection can reduce dust-related
hazards.
4) Power tool use and care
a) Do not force the power tool. Use the correct
power tool for your application.
The correct power tool will do the job better and
safer at the rate for which it was designed.
b) Do not use the power tool if the switch does
not turn it on and off.
Any power tool that cannot be controlled with the
switch is dangerous and must be repaired.
c) Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools.
Such preventive safety measures reduce the risk
of starting the power tool accidentally.
d) Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool.
Power tools are dangerous in the hands of
untrained users.
e) Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool’s operation.
If damaged, have the power tool repaired
before use.
Many accidents are caused by poorly maintained
power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are easier
to control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed.
Use of the power tool for operations different
from those intended could result in a hazardous
situation.
5) Battery tool use and care
a) Recharge only with the charger specified by
the manufacturer.
A charger that is suitable for one type of battery
pack may create a risk of fire when used with
another battery pack.
b) Use power tools only with specifically
designated battery packs.
Use of any other battery packs may create a risk of
injury and fire.
c) When battery pack is not in use, keep it away
from other metal objects like paper clips,
coins, keys, nails, screws, or other small
metal objects, that can make a connection
from one terminal to another.
Shorting the battery terminals together may cause
burns or a fire.
d) Under abusive conditions, liquid may be
ejected from the battery; avoid contact. If
contact accidentally occurs, flush with water.
If liquid contacts eyes, additionally seek
medical help.
Liquid ejected from the battery may cause irritation
or burns.
6) Service
a)Have your power tool serviced by a
qualified repair person using only identical
replacement parts.
This will ensure that the safety of the power tool is
maintained.
3
English
000BookDS18DSDLmetabo.indb3000BookDS18DSDLmetabo.indb3 2018/11/0111:52:092018/11/0111:52:09

12. Handle tool correctly.
Operate the tool according to the instructions provided
herein. Do not drop or throw the tool. Never allow the
tool to be operated by children, individuals unfamiliar
with its operation or unauthorized personnel.
13. Keep all screws, bolts and covers tightly in place.
Keep all screws, bolts, and plates tightly mounted.
Check their condition periodically.
14. Do not use power tools if the plastic housing or
handle is cracked.
Cracks in the tool’s housing or handle can lead to
electric shock. Such tools should not be used until
repaired.
15. Blades and accessories must be securely
mounted to the tool.
Prevent potential injuries to yourself or others. Blades,
cutting implements and accessories which have been
mounted to the tool should be secure and tight.
16. Never use a tool which is defective or operating
abnormally.
If the tool appears to be operating unusually, making
strange noises, or otherwise appears defective, stop
using it immediately and arrange for repairs by a
metabo HPT authorized service center.
17. Carefully handle power tools.
Should a power tool be dropped or struck against
hard materials inadvertently, it may be deformed,
cracked, or damaged.
18. Do not wipe plastic parts with solvent.
Solvents such as gasoline, thinner benzine, carbon
tetrachloride, and alcohol may damage and crack
plastic parts. Do not wipe them with such solvents.
Wipe plastic parts with a soft cloth lightly dampened
with soapy water and dry thoroughly.
19. Always wear eye protection that meets the
requirement of the latest revision of ANSI
Standard Z87.1.
20. This product contains a strong permanent magnet in
the motor.
Observe the following precautions regarding adhering
of chips to the tool and the effect of the permanent
magnet on electronic devices.
CAUTION
1
Do not place the tool on a workbench or work area
where metal chips are present.
The chips may adhere to the tool, resulting in injury or
malfunction.
– WARNING –
To reduce the risk of injury, user must read
instruction manual.
SPECIFIC SAFETY RULES AND SYMBOLS
1. Wear ear protectors with impact drills.
Exposure to noise can cause hearing
loss.
2. Use auxiliary handle(s), if supplied with the tool.
Loss of control can cause personal injury.
3. Hold power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring.
Cutting accessory contacting a “live” wire may make
exposed metal parts of the power tool “live” and could
give the operator an electric shock.
4. Hold power tool by insulated gripping surfaces,
when performing an operation where the
fastener may contact hidden wiring.
Fasteners contacting a “live” wire may make exposed
metal parts of the power tool “live” and could give the
operator an electric shock.
5. Never place hands or other body parts near the drill
bit or chuck during operation. Hold the drill by its
handle only.
6. Because the cordless driver drill operates by battery
power, be aware of the fact that it can begin to operate
at any time.
7. When working at elevated locations, clear the area
of all other people and be aware of conditions below
you.
8. Never touch moving parts.
Never place your hands, fingers or other body parts
near the tool’s moving parts.
9. Never operate without all guards in place.
Never operate this tool without all guards or safety features
in place and in proper working order. If maintenance or
servicing requires the removal of a guard or safety feature,
be sure to replace the guard or safety feature before
resuming operation of the tool.
10. Use right tool.
Don’t force small tool or attachment to do the job of a
heavy-duty tool.
Don’t use tool for purpose not intended —for
example— don’t use circular saw for cutting tree
limbs or logs.
11. Never use a power tool for applications other
than those specified.
Never use a power tool for applications other than
those specified in the instruction manual.
4
English
000BookDS18DSDLmetabo.indb4000BookDS18DSDLmetabo.indb4 2018/11/0111:52:092018/11/0111:52:09

2 If chips have adhered to the tool, do not touch it.
Remove the chips with a brush.
Failure to do so may result in injury.
3 If you use a pacemaker or other electronic medical
device, do not operate or approach the tool.
Operation of the electronic device may be affected.
4 Do not use the tool in the vicinity of precision devices
such as cell phones, magnetic cards or electronic
memory media.
Doing so may lead to misoperation, malfunction or
loss of data.
21. Definitions for symbols used on this tool
V ............ volts
—
---
......... direct current
no.......... no load speed
---/min.... revolutions or reciprocation per minute
IMPORTANT SAFETY INSTRUCTIONS
FOR BATTERY CHARGER
WARNING
Death or serious bodily injury could result from
improper or unsafe use of battery chargers.
To avoid these risks, follow these basic safety
instructions:
READ ALL INSTRUCTIONS
1. This manual contains important safety and operating
instructions for battery charger Model UC18YRSL/
UC18YFSL.
2. Before using battery charger, read all instructions
and cautionary markings on (1) battery charger, (2)
battery, and (3) product using battery.
3. To reduce risk of injury, charge metabo HPT
rechargeable battery type: for UC18YRSL/
UC18YFSL---BSL14 and BSL18 series. Other type
of batteries may burst causing personal injury and
damage.
4. Use of an attachment not recommended or sold by
the battery charger manufacturer may result in a risk
of fire, electric shock, or injury to persons.
5. To reduce risk of damage to electric plug and cord,
pull by plug when disconnecting battery charger.
6. Make sure cord is located so that it will not be stepped
on, tripped over, or otherwise subjected to damage or
stress.
7. An extension cord should not be used unless
absolutely necessary. Use of improper extension
cord could result in a risk of fire and electric shock.
If extension cord must be used make sure:
a. That blades of extension cord are the same
number, size, and shape as those of plug on
battery charger:
b. That extension cord is properly wired and in good
electrical condition; and
c. That wire size is large enough for AC ampere
rating of battery charger as specified in Table 1.
Table 1
RECOMMENDED MINIMUM AWG SIZE FOR
EXTENSION CORDS FOR BATTERY CHARGERS
AC Input Rating Amperes* AWG Size of Cord
Equal to or
greater than but less than
Length of Cord, Feet (Meter)
25 (7.5) 50 (15) 100 (30) 150 (45)
0 2 18 18 18 16
2 3 18 18 16 14
3 4 18 18 16 14
* If the input rating of a battery charger is given in watts
rather than in amperes, the corresponding ampere
rating is to be determined by dividing the wattage
rating by the voltage rating–for example:
1,250 watts = 10 amperes
125 volts
8. Do not operate battery charger with damaged cord or
plug-replace them immediately.
9. Do not operate battery charger if it has received a
sharp blow, been dropped, or otherwise damaged in
any way; take it to a qualified serviceman.
10. Do not disassemble battery charger; take it to a
qualified serviceman when service or repair is
required. Incorrect reassembly may result in a risk of
electric shock or fire.
5
English
000BookDS18DSDLmetabo.indb5000BookDS18DSDLmetabo.indb5 2018/11/0111:52:092018/11/0111:52:09

15. ALWAYS disconnect the power cord from its receptacle
when the charger is not in use.
CAUTION ON LITHIUM-ION BATTERY
To extend the lifetime, the lithium-ion battery equips with
the protection function to stop the output.
In the cases of 1 to 3 described below, when using this
product, even if you are pulling the switch, the motor may
stop. This is not the trouble but the result of protection
function.
1. When the battery power remaining runs out, the motor
stops.
In such case, charge it up immediately.
2. If the tool is overloaded, the motor may stop. In this
case, release the switch of tool and eliminate causes of
overloading. After that, you can use it again.
3. If the battery is overheated under overload work, the
battery power may stop.
In this case, stop using the battery and let the battery
cool. After that, you can use it again.
Furthermore, please heed the following warning and
caution.
WARNING
In order to prevent any battery leakage, heat generation,
smoke emission, explosion and ignition beforehand,
please be sure to heed the following precautions.
1. Make sure that swarf and dust do not collect on the
battery.
○ During work make sure that swarf and dust do not fall
on the battery.
○ Make sure that any swarf and dust falling on the power
tool during work do not collect on the battery.
○ Do not store an unused battery in a location exposed
to swarf and dust.
○ Before storing a battery, remove any swarf and dust
that may adhere to it and do not store it together with
metal parts (screws, nails, etc.).
2. Do not pierce battery with a sharp object such as a
nail, strike with a hammer, step on, throw or subject
the battery to severe physical shock.
3. Do not use an apparently damaged or deformed
battery.
4. Do not use the battery in reverse polarity.
5. Do not connect directly to an electrical outlets or car
cigarette lighter sockets.
6. Do not use the battery for a purpose other than those
specified.
7. If the battery charging fails to complete even when a
specified recharging time has elapsed, immediately
stop further recharging.
8. Do not put or subject the battery to high temperatures
or high pressure such as into a microwave oven,
dryer, or high pressure container.
11. To reduce risk of electric shock, unplug charger from
receptacle before attempting any maintenance or
cleaning. Removing the battery will not reduce this
risk.
IMPORTANT SAFETY INSTRUCTIONS
FOR USE OF THE BATTERY AND
BATTERY CHARGER
You must charge the battery before you can
use the power tool. Before using the model
UC18YRSL/UC18YFSL battery charger, be sure to read all
instructions and cautionary statements on it, the battery
and in this manual.
REMEMBER: USE ONLY metabo HPT BATTERY TYPES:
FOR UC18YRSL/UC18YFSL---BSL14 AND BSL18
SERIES. OTHER TYPES OF BATTERIES MAY BURST
AND CAUSE INJURY!
Follow these instructions to avoid the risk of injury:
WARNING: Improper use of the battery
or battery charger can lead to
serious injury. To avoid these
injuries:
1. NEVER disassemble the battery.
2. NEVER incinerate the battery, even if it is damaged or
is completely worn out. The battery can explode in a
fire.
3. NEVER short-circuit the battery.
4. NEVER insert any objects into the battery charger’s
air vents. Electric shock or damage to the battery
charger may result.
5. NEVER charge outdoors. Keep the battery away
from direct sunlight and use only where there is low
humidity and good ventilation.
6. NEVER charge when the temperature is below 32°F
(0°C) or above 104°F (40°C).
7. NEVER connect two battery chargers together.
8. NEVER insert foreign objects into the hole for the
battery or the battery charger.
9. NEVER use a booster transformer when charging.
10. NEVER use an engine generator or DC power to
charge.
11. NEVER store the battery or battery charger in places
where the temperature may reach or exceed 104°F
(40°C) such as inside metal box or car.
12. NEVER expose the battery or battery charger to rain
or wet conditions.
13.
ALWAYS operate charger on standard household
electrical power (120 volts). Using the charger on any
other voltage may overheat and damage the charger.
14.
ALWAYS wait at least 15 minutes between charges to
avoid overheating the charger.
6
English
000BookDS18DSDLmetabo.indb6000BookDS18DSDLmetabo.indb6 2018/11/0111:52:092018/11/0111:52:09

9. Keep away from fire immediately when leakage or foul
odor are detected.
10. Do not use in a location where strong static electricity
generates.
11. If there is battery leakage, foul odor, heat generated,
discolored or deformed, or in any way appears
abnormal during use, recharging or storage,
immediately remove it from the equipment or battery
charger, and stop use.
12. Do not immerse the battery or allow any fluids to flow
inside. Conductive liquid ingress, such as water, can
cause damage resulting in fire or explosion. Store your
battery in a cool, dry place, away from combustible
and flammable items. Corrosive gas atmospheres
must be avoided.
CAUTION
1. If liquid leaking from the battery gets into your eyes,
do not rub your eyes and wash them well with fresh
clean water such as tap water and contact a doctor
immediately.
If left untreated, the liquid may cause eye-problems.
2. If liquid leaks onto your skin or clothes, wash well with
clean water such as tap water immediately.
There is a possibility that this can cause skin irritation.
3. If you find rust, foul odor, overheating, discolor,
deformation, and/or other irregularities when using
the battery for the first time, do not use and return it to
your supplier or vendor.
WARNING
If an electrically conductive foreign object enters the
terminals of the lithium ion battery, a short-circuit may
occur resulting in the risk of fire. Please observe the
following matters when storing the battery.
○ Do not place electrically conductive cuttings,
nails, steel wire, copper wire or other wire in the
storage case.
○ Either install the battery in the power tool or store
by securely pressing into the battery cover until
the ventilation holes are concealed to prevent
short-circuits (See Fig. 1).
SAVE THESE INSTRUCTIONS
AND
MAKE THEM AVAILABLE TO OTHER USERS
AND
OWNERS OF THIS TOOL!
7
English
000BookDS18DSDLmetabo.indb7000BookDS18DSDLmetabo.indb7 2018/11/0111:52:092018/11/0111:52:09

FUNCTIONAL DESCRIPTION
NOTE
The information contained in this Instruction Manual is designed to assist you in the safe operation and maintenance
of the power tool.
NEVER operate, or attempt any maintenance on the tool unless you have first read and understood all safety
instructions contained in this manual.
Some illustrations in this Instruction Manual may show details or attachments that differ from those on your own
power tool.
NAME OF PARTS
1. Cordless Driver Drill / Cordless Hammer Drill (DS18DSDL / DV18DSDL)
Switch panel
Clutch dial
Keyless chuck
Shift knob
Side handle
Selector button
Housing
Switch trigger
Battery
Hook
Handle
Nameplate
LED Light
Ventilation holes
Latch
Terminals
Battery cover
Battery
○ Battery <BSL1830 >
Fig. 1
2. Battery Charger
Nameplate
Pilot lamp
Guide rail
Cord
Nameplate
Pilot lamp
Guide rail
Cord
<UC18YRSL> <UC18YFSL>
Fig. 2
8
English
000BookDS18DSDLmetabo.indb8000BookDS18DSDLmetabo.indb8 2018/11/0111:52:092018/11/0111:52:09

SPECIFICATIONS
1. Cordless Driver Drill / Cordless Hammer Drill
Model DS18DSDL DV18DSDL
Motor DC motor
No-load
speed
Low 0 – 350/min 0 – 400/min
High 0 – 1,600/min 0 – 1,800/min
Capacity
Drilling
Brick (Depth
1-1/4 in. (30 mm)) 5/8 in. (16 mm)
Wood (Thickness
11/16 in. (18 mm)) 2 – 9/16 in. (65 mm)
Metal (Thickness
1/16 in. (1.6 mm)) 1/2 in. (13 mm)
Screw
Driver
Wood screw #20 × 4 in.
(8 mm × 100 mm)
Small screw 1/4 in. (6 mm)
Drill chuck capacity Maximum gripping
diameter 1/2 in. (13 mm)
Battery
Model BSL1830
Type Li-ion battery
Voltage DC 18 V
Weight 4.6 lbs. (2.1 kg) 4.8 lbs. (2.2 kg)
2. Battery Charger
Model UC18YRSL UC18YFSL
Input power source Single phase: AC 120 V 60 Hz
Charging time
(At a temperature of 68°F (20°C)) Approx. 45 min
Charging voltage DC 14.4 – 18 V
Charging current DC 3.5 A
Weight 1.3 lbs. (0.6 kg) 1.1 lbs. (0.5 kg)
9
English
000BookDS18DSDLmetabo.indb9000BookDS18DSDLmetabo.indb9 2018/11/0111:52:102018/11/0111:52:10

ASSEMBLY AND OPERATION
1. Connect the charger’s power cord to a receptacle.
When the power cord is connected, the charger’s pilot
lamp will blink in red. (At 1-second intervals)
WARNING
Do not use the electrical cord
if damaged. Have it repaired
immediately.
2. Insert the battery to the battery charger.
Insert the battery into the battery charger as shown in
Fig. 4.
<UC18YRSL>
Pilot lamp
Charger
Battery
<UC18YFSL>
Pilot lamp
Charger
Battery
Fig. 4
3. Charging
When the battery is connected to the battery charger,
charging will commence and the pilot lamp will light in
red. (See Table 2)
NOTE
If the pilot lamp flikers in red, pull out the plug from
the receptacle and check if the battery is properly
mounted.
When the battery is fully charged, the pilot lamp
will blink in red slowly. (At 1-second intervals) (See
Table 2)
APPLICATIONS
<DV18DSDL>
○ Use as a hammer drill
Drilling of soft bricks and concrete blocks.
<DS18DSDL / DV18DSDL>
○ Use as a drill
Drilling of soft steel, wood, plastic and aluminum
materials.
○ Use as a screwdriver
Tightening and loosening of machine screws, wood
screws and tapping screws.
REMOVAL AND INSTALLATION METHOD
OF BATTERY
○
How to install the battery.
Align the battery with the groove in tool handle and
slip it into place.
Always insert it all the way until it locks in place with a
little click, If not, it may accidentally fall out of the tool,
causing injury to you or someone around you (Fig. 3).
○ How to remove the battery.
Withdraw battery from the tool handle while pressing
the latch (2 pcs) of the battery (Fig. 3).
Battery
Push
Pull out
Insert
Handle
Latch
Fig. 3
CHARGING METHOD
NOTE
Before plugging into the receptacle, make sure the
following points.
○ The power source voltage is stated on the
nameplate.
○ The cord is not damaged.
WARNING
Do not charge at voltage higher than indicated
on the nameplate.
If charged at voltage higher than indicated on the
nameplate, the charger will burn out.
10
English
000BookDS18DSDLmetabo.indb10000BookDS18DSDLmetabo.indb10 2018/11/0111:52:102018/11/0111:52:10

(1) Pilot lamp indication
The indications of the pilot lamp will be as shown in
Table 2, according to the condition of the charger or
the rechargeable battery.
Table 2
Indications of the pilot lamp
The pilot
lamp lights
or blinks.
Before
charging Blinks (red)
Lights for 0.5 seconds. Does not light for
0.5 seconds. (offfor 0.5 seconds)
While
charging Lights (red) Lights continuously
Charging
complete Blinks (red)
Lights for 0.5 seconds. Does not light for
0.5 seconds. (offfor 0.5 seconds)
Charging
impossible Flickers (red)
Lights for 0.1 seconds. Does not light for
0.1 seconds. (offfor 0.1 seconds) Malfunction in the battery or
the charger
Overheat
standby
Lights
(green)
<UC18YRSL>
Lights continuously
Battery overheated.
Unable to charge.
(Charging will commence
when battery cools)
Blinks
(red)
<UC18YFSL>
Lights for 1 second. Does not light for
0.5 seconds. (offfor 0.5 seconds)
(2) Regarding the temperature of the rechargeable
battery.
The temperatures for rechargeable batteries are as
shown in Table 3, and batteries that have become hot
should be cooled for a while before being recharged.
Table 3
Rechargeable
batteries Temperatures at which the
battery can be recharged
BSL1830 32°F–122°F (0°C–50°C)
4. Disconnect battery charger from the receptacle.
CAUTION
Do not pull the plug out of the receptacle by
pulling on the cord.
Make sure to grasp the plug when removing from
receptacle to avoid damaging cord.
5. Remove the battery from the battery charger.
Supporting the battery charger with hand, pull out the
battery from the battery charger.
Regarding electric discharge in case of new
batteries, etc.
As the internal chemical substance of new batteries
and batteries that have not been used for an extended
period is not activated, the electric discharge might
be low when using them the first and second time.
This is a temporary phenomenon, and normal time
required for recharging will be restored by recharging
the batteries 2 – 3 times.
How to make the batteries perform longer.
(1) Recharge the batteries before they become
completely exhausted.
When you feel that the power of the tool becomes
weaker, stop using the tool and recharge its battery.
If you continue to use the tool and exhaust the electric
current, the battery may be damaged and its life will
become shorter.
(2) Avoid recharging at high temperatures.
A rechargeable battery will be hot immediately after
use. If such a battery is recharged immediately after
use, its internal chemical substance will deteriorate,
and the battery life will be shortened. Leave the
battery and recharge it after it has cooled for a while.
11
English
000BookDS18DSDLmetabo.indb11000BookDS18DSDLmetabo.indb11 2018/11/0111:52:102018/11/0111:52:10

CAUTION
●
When the battery charger has been continuously
used, the battery charger will be heated, thus
constituting the cause of the failures. Once the
charging has been completed, give 15 minutes
rest until the next charging.
● If the battery is rechraged when it is warm due
to battery use or exposure to sunlight, the pilot
lamp may light in green.
The battery will not be recharged. In such a case,
let the battery cool before charging.
● When the pilot lamp flickers rapidly in red (at
0.2–second intervals), check for and take out
any foreign objects in the charger’s battery
installation hole. If there are no foreign objects,
it is probable that the battery or charger is
malfunctioning. Take it to your authorized
Service Center.
NOTE
Charging times may be longer depending on the
surrounding temperature and battery conditions.
BEFORE USE
Check the work area to make sure that it is clear of debris
and clutter.
Clear the area of unnecessary personnel. Ensure that
lighting and ventilation is adequate.
OPERATION
1. Mounting and dismounting of the bit.
(1) Mounting the bit.
Loosen the sleeve by turning it toward the left (in the
counterclockwise direction as viewed from the front)
to open the clip on the keyless chuck. After inserting
a driver bit, etc., into the keyless drill chuck, and
tighten the sleeve by turning it toward the right (in the
clockwise direction as viewed from the front). (See
Fig. 5).
Tighten
Loosen
Sleeve
Fig. 5
NOTE
If the sleeve becomes loose during operation, tighten
it further.
The tightening force becomes stronger when the
sleeve is tightened.
(2) Dismounting the bit
Loosen the sleeve by turning it toward the left (in the
counterclockwise direction as viewed from the front),
and then take out the bit etc. (See Fig. 5)
NOTE
○ If the sleeve is tightened in a state where the clip of the
keyless chuck is opened to a maximum limit, a click
noise may occur. This is the noise that occurs when
the loosening of the keyless chuck is prevented and is
not a malfunction.
○ When it is no longer possible to loosen the sleeve,
use a vise or similar instrument to secure the bit. Set
the clutch mode between 1 and 11 and then turn the
sleeve to the loose side (left side) while operating the
clutch. It should be easy now to loosen the sleeve.
2. Confirm that the battery is mounted correctly.
3. Installing/Removing the side handle.
CAUTION
Firmly install the side handle. If loose, the side
handle may gyrate or fall out and cause bodily
injury.
(1) Install the side handle so that the protrusions on the
main unit and grooves on the side handle interlock.
Tighten the grip after checking that the side handle is
not riding on the slip prevention protrusion. (Fig. 6).
(2) Loosen the grip to remove the side handle.
Tighten
Loosen
Concave
Side handle
Rotate preventing
protrusion
Slip
preventing
protrusion
Grip
Fig. 6
4. Check the rotational direction.
The bit rotates clockwise (viewed from the rear side)
by pushing the R-side of the selector button.
12
English
000BookDS18DSDLmetabo.indb12000BookDS18DSDLmetabo.indb12 2018/11/0111:52:102018/11/0111:52:10

Shift knob
High speed
Fig. 9
Operate the shift knob to change the rotational speed.
Move the shift knob in the direction of the arrow (See
Figs. 8 and 9).
When the shift knob is set to “LOW”, the drill rotates at
a low speed. When set to “HIGH”, the drill rotates at a
high speed.
CAUTION
●
When changing the rotational speed with the
shift knob, confirm that the switch is off.
Changing the speed while the motor is rotating
will damage the gears.
● When a large force is required for operation
(operations indicated in the following chart) set
the shift knob to “LOW”. If “HIGH” is set and the
unit is used, it may cause the motor to burn out
or malfunction prematurely.
6. The scope and suggestions for uses
The usable scope for various types of work based
on the mechanical structure of this unit is shown in
Table 4.
The L-side of the selector button is pushed to turn the
bit counterclockwise (See Fig. 7). (The and
marks are provided on the body.)
marks marks
Trigger
switch
Selector
button
Fig. 7
○ When the trigger switch is depressed, the tool rotates.
When the trigger is released, the tool stops.
○ The rotational speed of the drill can be controlled by
varying the amount that the trigger switch is pulled.
Speed is low when the trigger switch is pulled slightly
and increases as the trigger switch is pulled more.
CAUTION
The push button can not be switched while the
power tool is turning. To switch the push button,
stop the power tool, then set the push button.
○ When releasing the trigger of the switch, the brake will
be applied for immediate stopping.
5. Change rotation speed.
Shift knob
Low speed
Fig. 8
Table 4
Work Cap position Suggestions
Drilling
Brick
(DV18DSDL) Use for drilling purpose
Wood
Use for drilling purpose.Steel
Aluminum
Screw
tightening
Small screw 1 – 22 Use the bit and socket matching the screw diameter.
Wood screw 1 – Use after drilling a pilot hole.
13
English
000BookDS18DSDLmetabo.indb13000BookDS18DSDLmetabo.indb13 2018/11/0111:52:102018/11/0111:52:10

(3) When using this unit as a hammer drill, align the clutch
dial hammer mark “ ” with the triangle mark on the
outer body.
Hammer mark
Triangle mark
Drill mark
Clutch dial Weak
Strong
Fig. 12
CAUTION
●
The clutch dial cannot be set between the
number “1, 3, 5 ... 22” or the black dot.
● Do not use with the clutch dial number at “22”
and the black line at the middle of the drill mark.
Doing so may cause damage. (See Fig. 13)
Line
Drill mark Triangle mark Hammer mark
Fig. 13
8. Rotation to Hammer changeover (DV18DSDL)
The "Rotation (Rotation only)" and "Hammer (Hammer
+ Rotation)" can be switched by aligning the drill mark
"" or the hammer mark " " with the triangle mark
on the outer body.
○ To make holes in the metal, wood or plastic, switch to
"Rotation (Rotation only)".
○ To make holes in the bricks or concrete blocks, switch
to "Hammer (Hammer + Rotation)".
CAUTION
Do not use the Cordless hammer drill in the
"Hammer" setting if the material can be bored
by rotation only. Such action will not only reduce
drill efficiency, but may also damage the drill tip.
7. Confirm the clutch dial position (See Fig. 10).
<DS18DSDL>
The tightening torque of this unit can be adjusted
according to the clutch dial position, at which the
clutch dial is set.
Clutch dial
Triangle mark
Strong
Weak
Drill mark
Fig. 10
(1) When using this unit as a screwdriver, line up the one
of the numbers “1, 3, 5 ... 22” on the clutch dial, or the
black dot, with the triangle mark on the outer body.
(2) When using this unit as a drill, line up the clutch dial
drill mark “ ” with the triangle mark on the outer
body.
CAUTION
●
The clutch dial cannot be set between the
numbers “1, 3, 5 ... 22” or the black dot.
● Do not use with the clutch dial set at the line
between the number “22” and the drill mark
“”. Doing so may cause damage (See Fig. 11).
Line
Triangle mark
Drill mark
Fig. 11
<DV18DSDL> (Fig. 12)
The three modes of screwdriver, drill and hammer drill
can be switched by the position of the clutch dial in
this unit.
(1) When using this unit as a screwdriver, line up the one
of the numbers “1, 3, 5 ... 22” on the clutch dial, or the
black dot, with the triangle mark on the outer body.
(2) When using this unit as a drill, line up the clutch dial
drill mark “ ” with the triangle mark on the outer
body.
14
English
000BookDS18DSDLmetabo.indb14000BookDS18DSDLmetabo.indb14 2018/11/0111:52:102018/11/0111:52:10

9. Tightening torque adjustment.
(1) Tightening torque
Tightening torque should correspond in its intensity to
the screw diameter. When too strong power is used,
the screw head may be broken or be injured.
Be sure to adjust the clutch dial position according to
the screw diameter.
(2) Tightening torque indication (See Fig. 10, 12)
The tightening torque differs depending on the type of
screw and the material being tightened.
The unit indicates the tightening torque with the
numbers “1, 3, 5 ... 22” on the clutch dial, and a dot.
The tightening torque at position “1” is the weakest
and the torque is strongest at the highest number.
(3) Adjusting the tightening torque (See Fig. 10, 12)
Rotate the clutch dial and line up the numbers “1, 3,
5, ... 22” on the clutch dial, or the dot, with the triangle
mark on the outer body. Adjust the clutch dial in the
weak or the strong torque direction according to the
torque you need.
CAUTION
●
The motor rotation may be locked to cease while
the unit is used as drill. While operating the
driver drill, take care not to lock the motor.
● When setting the shift knob to “HIGH” (high
speed) and the position of the clutch dial is “17”
to “22”, it may happen that the clutch does not
engaged and that the motor is locked. In such
a case, please set the shift knob to “LOW” (low
speed).
● If the motor is locked, immediately turn the
power off. If the motor is locked for a while, the
motor or battery may be burnt.
● Too long hammering may cause the screw
broken due to excessive tightening.
● A buzzing noise is produced when the motor
is about to rotate; This is only a noise, not a
machine failure.
Table 5
Use Cap Position Rotating speed selection (Position of the shift knob)
LOW (Low speed) HIGH (High speed)
Screw
tightening
Machine screw 1 – 22 For 1/4 in. (6 mm) or smaller
diameter screws. For 5/32 in. (4 mm) or smaller
diameter screws.
Wood screw 1 – For 5/16 in. (8 mm) or smaller
nominal diameter screws.
For 3/16 in. (4.8 mm) or smaller
nominal
diameter screws.
Drilling
Brick (DV18DSDL) For 5/8 in. (16 mm) or
smaller diameters. For 15/32 in. (12 mm) or smaller diameters.
Wood For 2 – 9/16 in. (65 mm) or
smaller diam-eters. For 15/16 in. (24 mm) or smaller diameters.
Metal For drilling with a metal
working drill bit.
10. About Remaining Battery Indicator
When pressing the remaining battery indicator switch,
the remaining battery indicator lamp lights and the
battery remaining power can be checked. (Fig. 14)
When releasing your finger from the remaining battery
indicator switch, the remaining battery indicator lamp
goes off. The Table 6 shows the state of remaining
battery indicator lamp and the battery remaining
power.
Table 6
State of lamp Battery Remaining Power
The battery remaining power is
enough.
The battery remaining power
is a half.
The battery remaining power is
nearly empty.
Re-charge the battery soonest
possible.
As the remaining battery indicator shows somewhat
differently depending on ambient temperature and
battery characteristics, read it as a reference.
15
English
000BookDS18DSDLmetabo.indb15000BookDS18DSDLmetabo.indb15 2018/11/0111:52:112018/11/0111:52:11

Remaining battery
indicator switch
Remaining battery
indicator lamp
Fig. 14
NOTE
○ Do not give a strong shock to the switch panel or
break it. It may lead to a trouble.
○ To save the battery power consumption, the
remaining battery indicator lamp lights while pressing
the remaining battery indicator switch.
11. How to use the LED light
Every time you press the light switch on the switch
panel, the LED light lights or goes off. (Fig. 15)
To prevent the battery power consumption, turn offthe
LED light frequently.
Light switch
Fig. 15
CAUTION
Do not expose directly your eye to the light by
looking into the light.
If your eye is continuously exposed to the light,
your eye will be hurt.
NOTE
To prevent the battery power consumption caused by
forgetting to turn offthe LED light, the light goes off
automatically in about 15 minutes.
12. Using the hook
The hook is used to hang up the power tool to your
waist belt while working.
CAUTION
●
When using the hook, hang up the power tool
firmly not to drop accidentally.
If the power tool is dropped, it may lead to an
accident.
● When carrying the power tool with hooked to
your waist belt, do not fit any bit to the tip of
power tool. If the sharp bit such as drill is fitted
to the power tool when carrying it with hooked to
your waist belt, you will be injured.
● Install securely the hook. Unless the hook is
securely installed, it may cause an injury while
using.
(1) Removing the hook.
Remove the screws fixing the hook with Philips screw
driver. (Fig. 16)
Hook Screw
Fig. 16
(2) Replacing the hook and tightening the screws.
Install securely the hook in the groove of power
tool and tighten the screws to fix the hook firmly.
(Fig. 17)
Screw
Hook
Groove
Fig. 17
OPERATIONAL CAUTIONS
1. Resting the unit after continuous work
(1) The power tool is equipped with a temperature
protection circuit to protect the motor.
Continuous bolt-tightening work may cause the
temperature of the unit to rise, activating the
temperature protection circuit and automatically
stopping operation.
If this happens, allow the power tool to cool before
resuming use.
(2) After use for continuous tightening wood screw works,
rest the unit for 15 minutes or so when replacing the
battery. The temperature of the motor, switch, etc.,
will rise if the work is started again immediately after
battery replacement, eventually resulting in burnout.
16
English
000BookDS18DSDLmetabo.indb16000BookDS18DSDLmetabo.indb16 2018/11/0111:52:112018/11/0111:52:11

MAINTENANCE AND INSPECTION
CAUTION: Pull out battery before doing any inspection or maintenance.
1. Checking the condition of the bit
The bits should be checked regularly. If worn or
broken bits can slip or decrease the efficiency of the
motor and burn it out.
Replace worn bits with new ones.
CAUTION
If you use a driver bit of which point is worn or
broken, it will be dangerous since it slips. So
replace it with a new one.
2. Check the Screws
Loose screws are dangerous. Regularly inspect them
and make sure they are tight.
CAUTION
Using this power tool with loosened, screws is
extremely dangerous.
3. Maintenance of the motor
The motor unit winding is the very “heart” of the power
tool.
Exercise due care to ensure the winding does not
become damaged and/or wet with oil or water.
4. Inspecting the carbon brushes (Fig. 18)
The motor employs carbon brushes which are
consumable parts. Since and excessively worn
carbon brush can result in motor trouble, replace the
carbon brush with new ones when it becomes worn
to or near the “wear limit”. In addition, always keep
carbon brushes clean and ensure that they slide
freely within the brush holders.
NOTE
When replacing the carbon brush with a new one, be
sure to use the metabo HPT Carbon Brush Code No.
999054.
Wear limit
0.12" (3mm)
0.45"
(11.5mm)
Fig. 18
Nail of carbon brush
Protrusion of
carbon brush
Fig. 19
5. Replacing carbon brushes
Take out the carbon brush by first removing the brush
cap and then hooking the protrusion of the carbon
brush with a flat head screw driver, etc., as shown in
Fig. 20.
When installing the carbon brush, choose the
direction so that the nail of the carbon brush agrees
with the contact portion outside the brush tube. Then
push it in with a finger as illustrated in Fig. 21. Lastly,
install the brush cap.
CAUTION
●
Be absolutely sure to insert the nail of the carbon
brush into the contact portion outside the brush
tube. (You can insert whichever one of the two
nails provided.)
● Caution must be exercised since any error in this
operation can result in the deformed nail of the
carbon brush and may cause motor trouble at an
early stage.
Fig. 20
17
English
000BookDS18DSDLmetabo.indb17000BookDS18DSDLmetabo.indb17 2018/11/0111:52:112018/11/0111:52:11

Contact portion
outside brush tube
Fig. 21
6. Check for Dust
Dust may be removed with a soft cloth or a cloth
dampened with soapy water.
Do not use bleach, chlorine, gasoline or thinner, for
they may damage the plastics.
7. Disposal of the exhausted battery
WARNING
Do not dispose of the exhausted battery. The
battery must explode if it is incinerated. The
product that you have purchased contains a
rechargeable battery. The battery is recyclable.
At the end of it’s useful life, under various state
and local laws, it may be illegal to dispose of this
battery into the municipal waste stream. Check
with your local solid waste officials for details
in your area for recycling options or proper
disposal.
8. Storage
Storing in a place below 104°F (40°C) and out of the
reach of children.
NOTE
Storing lithium-ion batteries
Make sure the lithium-ion batteries have been fully
charged before storing them.
Prolonged storage (3 months or more) of batteries with
a low charge may result in performance deterioration,
significantly reducing battery usage time or rendering
the batteries incapable of holding a charge.
However, significantly reduced battery usage time
may be recovered by repeatedly charging and using
the batteries two to five times.
If the battery usage time is extremely short despite
repeated charging and use, consider the batteries
dead and purchase new batteries.
9. Service and repairs
All quality power tools will eventually require servicing
or replacement of parts because of wear from normal
use. To assure that only authorized replacement parts
will be used, all service and repairs must be performed
by a metabo HPT AUTHORIZED SERVICE CENTER,
ONLY.
CAUTION
In the operation and maintenance of power tools,
the safety regulations and standards prescribed
in each country must be observed.
Important notice on the batteries for the
metabo HPT cordless power tools
Please always use one of our designated genuine
batteries. We cannot guarantee the safety and
performance of our cordless power tool when used
with batteries other than these designated by us, or
when the battery is disassembled and modified (such
as disassembly and replacement of cells or other
internal parts).
18
English
000BookDS18DSDLmetabo.indb18000BookDS18DSDLmetabo.indb18 2018/11/0111:52:112018/11/0111:52:11

TROUBLESHOOTING GUIDE
WARNING
• To avoid injury from an accidental start, turn the switch OFF and remove the plug from the power source or remove
the battery from the main body before making any adjustments.
• All electrical or mechanical repairs should be done only by qualified service technicians. Contact metabo HPT
Authorized Service Center.
Problem Possible Cause Possible Solution
Tool will not start. Battery not installed properly. Check the battery installation.
Battery not charged. Charge battery using appropriate charger.
Battery overheated. Remove battery from tool and let battery
cool for while.
Battery will not charged. Battery pack not installed into Charger
properly. Insert battery into charger until charge status lamp (red) appears.
Charger not plugged in. Plug charger into a working receptacle.
Battery temperature too hot Remove battery from charger, cool battery.
For more detail, refer to “Charging
Method”.
Battery temperature too cold Remove battery from charger, move
battery and charger to a surrounding air
temperature of above 32°F (0°C)
For more detail, refer to “Changing
Method”.
19
English
000BookDS18DSDLmetabo.indb19000BookDS18DSDLmetabo.indb19 2018/11/0111:52:112018/11/0111:52:11

ACCESSORIES
WARNING
ALWAYS use Only authorized metabo HPT replacement parts and accessories. NEVER use replacement
parts or accessories which are not intended for use with this tool. Contact metabo HPT if you are not sure
whether it is safe to use a particular replacement part or accessory with your tool.
The use of any other attachment or accessory can be dangerous and could cause injury or mechanical
damage.
NOTE
Accessories are subject to change without any obligation on the part of the metabo HPT.
STANDARD ACCESSORIES
DS18DSDL
DV18DSDL
3
5
2
4
1
6
3
1
Phillips bit (No. 2 × 65L) (Code No. 983006) .........................................1
2 Battery (BSL1830) .................................................................................2
3 Battery Charger (UC18YRSL or UC18YFSL).........................................1
4 Plastic Case (Code No. 323230) ...........................................................1
5 Battery cover (Code No. 329897)..........................................................1
6 Side Handle (Code No.331906).............................................................1
OPTIONAL ACCESSORIES.....sold separately
○
Battery (BSL1830)
NOTE
Specifications are subject to change without any obligation on the part of the metabo HPT.
20
English
000BookDS18DSDLmetabo.indb20000BookDS18DSDLmetabo.indb20 2018/11/0111:52:112018/11/0111:52:11