Metabo HPT UU 240R Troubleshooting guide

– 1 –
English
Model
Modelo
Modèle
Universal Miter Saw Stand
Support Universel Pour Scie À Onglet
Soporte Universal De Ingletadora
UU 240R
SAFETY INSTRUCTIONS AND INSTRUCTION MANUAL
Improper or unsafe use of this miter saw stand can result in death or serious bodily injury!
This manual contains important information about product safety. Please read and understand this manual
BEFORE using the miter saw stand. Please keep this manual available for users and owers before they use
the miter saw stand. This manual should be stored in a safe place.
WARNING
INSTRUCCIONES DE SEGURIDAD E MANUAL DE INSTRUCCIONES
AVERTISSEMENT
¡El uso inadecuado o inseguro de este soporte para sierra ingletadora puede causar lesiones corporales
serias o la muerte!
Este manual contiene información importante acerca de la seguridad del producto. Lea y entienda este
manual ANTES de utilizar el soporte para sierra ingletadora. Mantenga este manual disponible para los
usuarios y propietarios antes de utilizar el soporte para sierra ingletadora. Este manual se debe guardar en
un lugar seguro.
INSTRUCTIONS DE SECURITE ET MODE D’EMPLOI
L’usage inapproprié ou dangereux de ce support pour scie à onglet peut entraîner la mort ou des blessures
corporelles graves!
Ce manuel contient des informations importantes liées à la sécurité du produit. Veillez à lire et comprendre
ce manuel AVANT d’utiliser le support pour scie à onglet. Conservez ce manuel pour que les utilisateurs et
propriétaires le consultent avant d’utiliser le support pour scie à onglet. Ce manuel doit être conservé dans
un endroit sûr.
ADVERTENCIA

– 2 –
English
CONTENTS
SECTION PAGE SECTION PAGE
Denition of Signal Words .................................. 3Know Your Stand ................................................ 7
General Safety .................................................... 3Assembly .............................................................. 8
Miter Saw Stand Safety ...................................... 4Adjustment .......................................................... 13
Carton Contents ................................................. 5Operation ............................................................. 15
Product Specications ........................................ 7Maintenance ......................................................... 16
English
ÍNDICE
Español
TABLE DES MATIERES
Français
SECTION PAGE SECTION PAGE
Dénition des symboles ......................................17 Connaître votre support ...................................... 21
Sécurité générale ................................................ 17 Assemblage .......................................................... 22
Sécurité du support pour scie à onglet ................ 18 Réglage ................................................................ 28
Contenu de l'emballage ...................................... 19 Utilisation ..............................................................30
Caractéristiques du produit ................................. 21 Maintenance ......................................................... 31
SECCIÓN PÁGINA SECCIÓN PÁGINA
Denición de las palabras de señalización ......... 33 Conozca su soporte ........................................... 37
Seguridad general .............................................. 33 Ensamblaje ......................................................... 38
Seguridad del soporte para sierra ingletadora .... 34 Ajustes ................................................................ 44
Contenido de la caja ........................................... 35 Operación ............................................................ 46
Especicaciones del producto ............................ 37 Mantenimiento ..................................................... 47

– 3 –
English
GENERAL SAFETY
WARNING
WARNING
●Failure to follow these rules may result in serious personal injury.
●To reduce the risk of injury, keep both hands on stand handles when raising and lowering the stand.
●Before folding the stand, miter saw MUST be removed from the stand.
●Use only with metabo HPT mounting brackets. Mounting brackets offered by other than metabo HPT have not been
tested with this stand and use of them could be hazardous.
Please read and understand this entire manual before attempting to assemble, operate or install the product. These
safety instructions are not meant to cover every possible condition that could occur.
DEFINITION OF SIGNAL WORDS
● WARNING indicates a hazardous situation that if not avoided, could result in death or serious injury.
● CAUTION indicates a hazardous situation that if not avoided, could result in minor or moderate injury, or
may cause machine damage.
● NOTE emphasizes essential information.
GENERAL SAFETY INFORMATION
Read and understand all warnings and operating instructions before using any tool or equipment. When using
tools or equipment, basic safety precautions should always be followed to reduce the risk of personal injury.
Improper operation, maintenance or modication of tools or equipment could result in serious injury and
property damage. There are certain applications for which tools and equipment are designed. Do not modify
the stand in any manner, or use the stand for unintended purpose.

– 4 –
English
MITER SAW STAND SAFETY
SAFETY INSTRUCTIONS FOR USING THE MITER SAW STAND
●Keep children away. All visitors should be kept at a safe distance from the work area.
● Always keep work area clean. Cluttered areas and benches invite accidents.
●Before you use the stand, make sure no parts of the stand are damaged or deformed.
●Before you use the stand, make sure all the parts or components of the stand are properly installed.
●Do not use in dangerous environment. Do not use the stand in damp or wet locations, or expose them to rain. Keep
work area well lighted.
● Always use the stand on a at and level surface. Do not use it at an uneven or unstable surface. Also, do not use
the stand on slippery surface. It will greatly reduce the stand loading capacity.
●The stand is designed to be used as a stand for metabo HPT miter saws and has a capacity of up to 300 lbs (136
kgs). The total weight of the miter saw and workpiece must not exceed the capacity of this stand. Any misuse or
abuse can result in product damage or personal injury.
● Do not sit or stand on the stand. Do not hang or put anything on it other than the miter saw on the stand.
● Do not modify the stand in any manner, or do not use the stand for any purpose other than for mounting a
metabo HPT miter saw.
●The stand should be used only for metabo HPT miter saws with a blade diameter up to 12” (305 mm). However, the
stand will not work with C12FSA.
●The miter saw should be rmly mounted with the stand as per the instruction manual.
●Align the position and balance of the miter saw as per this instruction manual after mounting the miter saw on the
stand.
●Take care during the raising and lowering of the stand to reduce the hazard of pinching hands and ngers.
● Disconnect the power plug from the receptacle when mounting or dismounting the miter saw from the stand.
●Mount the miter saw on the stand with the help of two or more people for your safety.
●When you mount the miter saw on the stand, hold the miter saw rmly by hands until the mounting bracket cam
latches are tightly secured to prevent the miter saw from falling down from the stand rails.
●After mounting the miter saw on the stand, make sure the stand will not fall over or be unintentionally moved by
vibration, wind, impact or other foreseeable external forces. If this cannot be fullled, then stability shall be obtained
by special safety measures. For example, securely anchor the stand to the ground or foundation.
●Occasionally check the stand and the miter saw, making sure the mounting of the miter saw is still tight. A loose
stand is unstable and may shift while in use causing serious injury.
● Before operating the mounted miter saw, read carefully the instruction manual for the miter saw.
●Before operating the miter saw, conrm that the cam latches on the both mounting brackets are rmly fastened so
that the miter saw is securely mounted on the stand.
● To prevent the miter saw from falling over from the stand, neatly layout the power cable on the ground to prevent
operator or by standers from getting caught up by the cable.
● Wear proper apparel. Do not wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry which may get
caught in moving parts. Nonslip footwear is recommended. Wear protective hair covering to contain long hair.
● Always wear eye protection with side shields that meets the requirements of ANSI Z87.1 when working with the
miter saw to prevent eye injury. Ordinary eyeglasses do not provide adequate protection because they do not
contain impact resistant safety glass. Also, use a face mask for additional safety and wear a dust mask if the cutting
operation produces dust.
● Do not overreach. Keep proper footing and balance at all times.
● When cutting a long piece of wood, be careful about the material supporting position because the cut material may
lose its balance and fall down from the stand. Also, if workpiece is placed beyond the work support, the leg on the
other side of the stand may be suddenly lifted up due to unbalance of weight. To prevent such occurrence, rmly
hold the opposite side and use extra support before starting cutting operation.
●
To detach the miter saw from the stand, conrm the cutting head is pulled forward and locked in the down position, then
unlock the mounting bracket cam latches while holding the miter saw rmly by hands to prevent the miter saw from

– 5 –
English
SAVE THESE INSTRUCTIONS AND MAKE THEM AVAILABLE TO OTHER USERS AND
OWNERS OF THIS STAND.
UNPACKING YOUR STAND
This product requires assembly.
1. Remove the stand and all parts from the carton.
2. Place the stand on the ground.
3. Separate all parts from the packing material. Check each one with the list below and the illustration on page 6 to
make certain all items are accounted before discarding any packing material.
If any part is missing or damaged, do not attempt to assemble the stand until the missing or damaged part is correctly
replaced.
TABLE OF LOOSE PARTS
CARTON CONTENTS
ITEM DESCRIPTION QUANTITY
AStand 1
BRight stand leg assembly 1
CStand handle tube 2
DStand leg tube with foot pad 1
EMiter saw mounting bracket 2
FAuxiliary mounting bracket 2
GStand leg tube with adjustable foot pad 1
H Left extension support 1
I Right extension support 1
JFence (left and right) 2
KExtension support assembly lock knob hardware bag 1
LStand handle assembly hardware bag 1
MStand leg assembly hardware bag 1
N Link bar assembly hardware bag 1
OBumper assembly hardware bag 1
PAnchor plates 1
QAuxiliary mounting brackets assembly hardware bag 1
RWheel mounting assembly hardware bag 1
S Wheel 2
WARNING
NOTE: In case of missing or damaged parts, please contact metabo HPT at [phone] for assistance.
falling down from the stand rails. Remove the miter saw with the mounting brackets carefully by two or more people.
● When transporting the stand in a vehicle, securely tie it down to prevent movement and possible damage.
● To reduce the risk of injury, periodically check that all fasteners are attached and adjusted according to the assembly
instructions included in this manual.
● If any part of the stand is not operating properly, the stand must be serviced before use. When servicing the stand,
use only identical metabo HPT replacement parts. Repairs should be conducted only by a metabo HPT authorized
service center.

– 6 –
English
L
R
UNPACKING AND CHECKING CONTENTS
A
TOP
LEFT RIGHT
BOTTOM
B C
FD
G
E
K-Extension Support L-Stand Handle M-Stand legs
H
N-Link Bar O-Bumper Assembly P-Anchor Plates
IJ
Q-Auxiliary Mounting Brackets R-Wheel Mounting S

– 7 –
English
KNOW YOUR STAND
PRODUCT SPECIFICATIONS
Stand height (ground to saw mounting brackets) 33-15/16 in. (862 mm)
Stand bed size 18 in. x 36 in. (457 mm x 915 mm)
Size of the folded stand 51-11/32 in. (L) x 24-19/32 in. (W) x 30-1/2 in. (H)
(1,304 mm x 626 mm x 775 mm)
Size of the extended stand 60-1/4 in. (L) x 24-19/32 in. (W) x 35-5/8 in. (H)
(1,531 mm x 626 mm x 906 mm)
Diameter of wheel 8 in. (203 mm)
Maximum weight load of stand 300 lbs (136 kgs)
*Do not place heavier load on this stand.
Maximum extension of supports 98 in. (2,489 mm)
*Do not apply a longer material.
Weight of stand 63.1 lbs (28.6 kgs)
The stand should be used only for metabo HPT miter saws with a blade diameter up to 12” (305 mm). However,
the stand will not work with C12FSA.
LEFT
REAR
RIGHT
REAR
Left extension
support assembly
Stand locking
levers Power cord hooks
Stand bed
Stand handles
Auxiliary mounting brackets
Foot pedal
Foot pad
Anchor plate
REAR VIEW
RIGHT
FRONT
LEFT
FRONT
FRONT VIEW
Wheels
Work stop plate
adjustment knob
Work stop plate Right extension
support assembly
Stand legs
Adjustable foot pad
Cam latch
Locking button
Height adjustment knob
of extension support
Miter Saw mounting brackets
Bumper
Link bars

– 8 –
English
ASSEMBLY INSTRUCTIONS
For your own safety, never connect the miter saw
plug to any power source outlet until all assembly and
adjustment steps are completed, and you have read
and understood the safety and operating instructions
for both this stand and your miter saw.
Use the box cutter to carefully open the carton and cut
the cable ties. Place the main stand assembly on a
large, at surface with the top facing down. Open the
stand legs by releasing the green ‘foot’ pedal.
INSTALLING THE BUMPERS (FIG. A)
1. Hardware Bag “O” - Attach one bumper (1) to the
stand with a screw (2) and a nut (3) and tighten
using a Phillips screwdriver and a 10 mm wrench.
Do not overtighten.
2. Repeat the same installation procedure for the
other bumper (4).
Fig. A
INSTALLING THE TWO LINK BARS (FIG. B)
NOTE: One end of the link bar (4) is attached to the
stand assembly. You need to attach the other end to
the stand.
1. Hardware Bag “N” - Insert the bolt (1) and curved
washer (6) through the hole on the stand tube (2),
into the at washer (3) and the link bar (4).
WARNING
ASSEMBLY
NOTE: The at washer (3) should be placed
between the tube (2) and the link bar (4).
2. Tighten the bolt (1) with the lock nut (5) using two
13 mm wrenches or two adjustable wrenches. Do
not overtighten.
NOTE: Make sure the curved washers are ush
against the stand leg before tightening.
3. Repeat the same installation procedure for the
other link bar.
Fig. B
INSTALLING THE RIGHT STAND LEG ASSEMBLY
(FIG. C)
1. Hardware Bag “M”- Insert the right stand leg (1)
into the stand (2).
NOTE: Align the four holes of the right stand leg
with the holes on the stand.
2. Insert the bolt (3) through a curved washer (4) and
into one of the holes (5) in the stand. Place another
curved washer (4) and then a lock nut (6). Tighten
using two 13 mm or adjustable wrenches.
3. Repeat for the three other holes. There are two
mounting holes on each side for securing the right
stand leg assembly to the stand.
NOTE: Make sure the curved washers are ush with
against the stand leg before tightening.
Fig. C
1
2
3
6
5
4
4
TOOLS NEEDED FOR ASSEMBLY
The stand needs to be assembled by the user.
Tools needed for assembly are (not supplied):
10 mm wrench, two 13 mm wrenches, two 17 mm
wrenches, two adjustable wrenches, 5 mm hex wrench,
a box cutter and a Phillips screwdriver.
1
2
36
4
5
2
4
1
3

– 9 –
English
INSTALLING THE WHEELS (FIG. D, D-1)
NOTE: Verify that the front side of the wheel with three
ribs is facing out. (Fig. D)
Fig. D
1. Hardware Bag “R”- Attach one wheel (1) to the
outer side of the right stand leg (2) using the hex
bolt (3), two at washers (4), sleeve (5) and the
nut (6), as shown in Fig. D-1.
NOTE: The sleeve (5) goes inside the opening in
the wheel.
2. Tighten the nut and bolt using two 17 mm or
adjustable wrenches.
NOTE: Do not overtighten or the wheel will not turn.
3. Spin the wheel to make sure it moves properly.
4. Repeat the above steps for the other wheel.
Fig. D-1
NOTE: If you plan to use the anchor plates to
attached the stand to the ground, please see section
on page 12.
INSTALLING THE STAND LEG TUBES (FIG. E)
With assistance, turn the stand so that the stand bed is
facing up.
1. Hardware Bag “M”- Insert one stand leg tube (1)
into the stand (2). Align the two holes of the stand
leg tube (1) with the holes on the stand.
2. Insert bolt (3) though a curved washer (4), onto one
of the holes (5) on the stand and then though
another curved washer (4). Then, tighten the
bolt (3) with lock nut (6) using two 13 mm or
adjustable wrenches.
NOTE: There are two mounting holes for securing
the leg tube to the stand on each side. One is from
the vertical direction; the other one is the horizontal
direction.
3. Repeat steps 1-2 for the other leg tube.
Fig. E
INSTALLING THE STAND HANDLE TUBES (FIG. F)
With assistance, raise the stand up so that it is
standing upright.
1. Hardware Bag “L”- Attach one stand handle (1) to
one side of the stand using two screws (2) and two
nuts (3). Tighten with a phillips screwdriver and a
10 mm or adjustable wrench. Repeat this step for
assembling the other stand handle tube.
NOTE: Both stand handles are the same. There are
two mounting holes for securing each handle tube to
the stand. One is from the vertical direction; the other
one is the horizontal direction.
Fig. F
Be sure to perform a folding test at this stage by
following the instruction in section “FOLDING THE
STAND” on page 15. If the stand can not be fully
folded and locked, please check if the bumpers are
installed properly and retighten screws and nuts for the
bumpers again. If the stand cannot be locked after the
adjustment, the stand must be serviced before use.
3
1
4
65
2
4
12
3
2
3
FRONT BACK
1
2
3
4
4
6
6
5
3
WARNING

– 10 –
English
INSTALLING THE SAW MOUNTING BRACKETS
(FIG. I)
NOTE: The cam latches of the saw mounting brackets
should point toward the user (front) as shown in Fig. I.
1. Press the locking button (1) and lift up on the cam
latch (2).
2. Place the rear holding clamp (3) on the rear rail of
the stand, and then lower the front end of the saw
mounting bracket over the front rail of the stand.
3. Slide the saw mounting bracket to the desired
position, and then push down the cam latch (2)
to lock.
4. Repeat the above steps for the other saw mounting
bracket.
NOTE: If either mounting bracket does not slide
smoothly on the stand bed when unlocked, see page 13
on “ADJUSTING THE SAW MOUNTING BRACKETS”.
Fig. I
POWER CORD HOOKS (FIG. J)
NOTE: These power cord hooks are pre-assembled at
the factory.
Storage for the power cord is located on the ends of the
saw mounting brackets (1). Wrap the power cord onto
the hooks (2) when the saw is not in use. This can help
prevent damage to the power cord.
Fig. J
INSTALLING THE EXTENSION SUPPORT ASSEMBLY
(FIG. G, H)
NOTE: The longer side of the horizontal tube (1) should
point toward the user (front) as shown in Fig. G.
1. Hardware Bag “K”- Attach the left fence (2) to the
left extension support (3) and secure by the lock
knob (4) with the shorter length threads and a at
washer (5). (Fig. G)
NOTE: There is a “L” mark on the inner side of the
left fence and a “R” mark on the inner side of the
right fence, not shown in the gure.
2. Repeat the above steps for installing the right fence
to the right extension support.
Fig. G
3. Insert the right extension support assembly (6) into
the right extension support arm (7) and secure with
the height adjustable knob (8) with the longer length
threads. (Fig. H)
4. Repeat the above steps for installing the left
extension support assembly.
Fig. H
1
2
1 2
3
8
7
6
423
1
5
left extension support right extension support
11
Long
side

– 11 –
English
Fig. L
5. Make sure the cam latches (6) of the saw mounting
brackets (4) are in the unlocked position. (Fig. M)
6. Lower the rear and front ends of the mounting
brackets assembly onto the rear and front rails of the
stand. The front holding clamps of the saw mounting
brackets (4) must seat fully on the front rail. Make
sure that the saw mounting brackets are positioned
at right angle to the front and rear rail.
7. Lock the mounting brackets assembly in position by
pressing down on the two cam latches (6).
● Ensure that the saw mounting brackets are clamped
securely on the stand before mounting the miter saw.
● Stay alert. The stand and miter saw may fall down
during the procedure and cause serious injury.
● To reduce the risk of injury, ensure all bolts and nuts
are properly tightened and all mechanisms properly
function after completing assembling and before
each use.
Fig. M
3
5
1
2
4
insert
insert
2
1
MOUNTING THE SAW TO THE STAND
● Do not mount the miter saw to the stand without
rst ensuring the stand is extended fully and locked
securely. To set up the stand, follow the instruction
in section “SETTING UP THE STAND” on page 15.
Failure to do so may result in possible injury and
damage to the stand and the miter saw.
● Always use the saw mounting brackets and auxiliary
mounting brackets together when mounting the miter
saw to the stand.
● Before operating the mounted miter saw, read
carefully the instruction manual for the miter saw.
USING THE AUXILIARY MOUNTING BRACKETS
(FIG. K, L, M, N)
1. Hardware Bag “Q”- Insert two square nuts (1)
into the slot on each end of both auxiliary mounting
brackets (2) and slide them to the middle of the
auxiliary mounting brackets (2). (Fig. K)
Fig. K
2. Insert two large washers (3) into the auxiliary
mounting bracket (2) and align with the holes at the
end of the auxiliary mounting bracket (2). (Fig. L)
3.
To mount the auxiliary mounting bracket (2) onto
the saw mounting brackets (4), insert the screw (5)
through the inserted washer (3) and the square nut (1)
below the saw mounting bracket (4) for xing each end
of the auxiliary mounting bracket (2) by using 5 mm
hex wrench.
4. Repeat the above steps of 2 & 3 for assembling the
other auxiliary mounting bracket.
NOTE: Do not tighten the four screws (5) securely at
this time.
WARNING
WARNING
6
4
mounting brackets
assembly

– 12 –
English
Fig. N
INSTALLING THE ANCHOR PLATE (FIG. O)
Hardware Bag “P” - Please follow the steps to
assemble the anchor plate to make the stand stable for
operation.
1. Move the stand to a desired place and make sure it
is on a at surface.
2. Loosen the nut (1) at the inner side of the sleeve (2),
using two 17 mm wrenches.
3. Locate the anchor plate (3) onto the sleeve (2) and
tighten the nut (1) again.
4. Repeat above steps for assembling the other anchor
plate.
5. Fix both anchor plates (3) to the at surface with
anchors (screw, bolt, peg etc. (not supplied)) which
are suitable for the type of ground surface (soil, wood
ooring, concrete etc.).
● Ensure that both anchor plates are xed rmly to the
ground and the stand is stable.
● Appropriate way to x the anchor plates may differ
according to the type of ground surface. If the anchor
plates are not rmly xed and the stand is unstable,
please take appropriate measures to x the anchor
plates.
Fig. O
● The cutting head of all sliding miter saw must be
locked in both the forward and down positions before
any attempt is made to mount to the stand. Failure to
do so may result in serious personal injury.
● Do not use the miter saw on the stand when the legs
of stand are folded.
● Layout the power cable neatly to prevent the power
cable causing the stand to tip over when performing
cutting operations.
8. Unplug the miter saw and lock the cutting head to its
down position. If the miter saw has a sliding rail, lock
the cutting head at down and forward position. Put
the miter saw on the mounting brackets assembly.
NOTE: For your own safety, position the miter saw
on the brackets with the help of two or more people.
9. Slide the square nuts (1) to the slots of the auxiliary
mounting brackets (2) and align to the mounting
holes of the miter saw. (Fig. N)
10. Insert the bolt (7) through the small washer (8),
the mounting hole of the miter saw, the slot of the
auxiliary mounting bracket (2) into the square
nut (1) to mount and lock the miter saw to the
auxiliary mounting bracket. (Fig. N) Repeat the above
steps for the other three mounting holes to lock the
miter saw onto the mounting bracket assembly.
NOTE: Adjust the position of the auxiliary mounting
brackets as close as possible to the front end of the
saw mounting brackets.
11.
Tighten all screws (5) and bolts (7) using a 5 mm hex
wrench.
12. After securely mounting the miter saw, unlock the
hold-down latch of the miter saw and carefully
move the cutting head up and down. If the stand tends
to fall down, reposition the miter saw.
13. Unlock the slide carriage lock knob of the miter saw
and carefully slide the cutting head forward. If the
stand tends to fall down, reposition the miter saw for
more stable position on the brackets.
14. Carefully perform sliding movement test at the
maximum miter and bevel angles to ensure the stability
of the stand and the miter saw.
● Do not mount the miter saw with the front of the saw
on the back side of the stand. The miter saw should
be mounted with the wheels of the stand to the right
when facing the front of the miter saw as shown in
Fig. N.
● When you dismount the miter saw, remove the miter
saw together with the mounting brackets assembly,
so that you can put the miter saw and the mounting
brackets assembly all together from next time. For
your own safety, mount or dismount the miter saw by
two or more people.
WARNING
7
8
2
1
Left side
of stand
Right side
of stand
not included
3
21
WARNING
WARNING

– 13 –
English
To reduce the risk of serious personal injury, turn off
and disconnect the miter saw from power source outlet
before installing and removing mounting brackets,
making adjustment or doing repairs. An unintentional
start-up can cause injury.
ADJUSTMENT INSTRUCTIONS
ADJUSTING FOOT PAD (FIG. P)
NOTE: The adjustable foot pad is used to level the
stand.
1. Loosen the wing nut (1), turn the adjustable foot
pad (2) clockwise to raise and counterclockwise to
lower the stand, then tighten the wing nut (1).
Fig. P
ADJUSTING THE EXTENSION SUPPORTS (FIG. Q)
The extension support assembly helps keep the
workpiece level and stable during cutting operations.
1. Lift the cam locking handle (1) up to loosen the
extension support
and slide the extension arm (2) to
the desired length. Press down on the cam locking
handle (1) to lock the extension support in place.
2. Loosen the height adjustment knob (3) to adjust the
extension support assembly (4) to the desired height
and then tighten the height adjustment knob (3).
3. If repetitive cutting is required, loosen the plate
adjustment knob (5) to adjust the work stop plate (6)
to the desired height, and then tighten.
4. The adjustment steps for other side of the extension
support assembly is the same as the above steps.
Fig. Q
ADJUSTING THE SAW MOUNTING BRACKETS
(FIG. R)
If the saw mounting brackets can slide over the top rails
or be removed from the top rails when the bracket cam
latches (1) are locked, the bracket adjustment screws (2)
need to be tightened. If the saw mounting brackets do not
t over the top rails, the bracket adjustment screws need
to be loosened.
NOTE: The miter saw should be removed from the
mounting brackets before attempting to tighten or loosen
the bracket adjustment screws (2).
1. Loosen the lock nut (3) using a 10 mm wrench.
2. Go through the hole (4) of the power cord clamp (5)
by using a Phillips screwdriver to turn the adjustment
screw for the saw mounting bracket. Turn the screw
clockwise to tighten the bracket, or counterclockwise
to loosen it.
NOTE: If the cam latch of the saw mounting bracket
cannot easily be pushed down into the lock position,
the adjustment screw is too tight. Do not force
the cam latch into the lock position. Loosen the
adjustment screw (2) to adjust it.
3. Press the locking button (6) and lift up the cam
latch (1) so the rear holding clamp is fully extended.
4. Install the rear holding clamp on the back rail of the
stand, then lower the front end of the saw mounting
bracket over the front rail of the stand to seat the
bracket fully over the rails.
5. Lock the bracket into place and make sure there is
no movement.
Ensure the saw mounting brackets is placed perpendicular
to the top rails to prevent potential loosening of the
adjustment screw when performing a cutting operation.
ADJUSTMENT
3
4
5
6
1
2
WARNING
WARNING
raise the stand lower the stand
21 2
1

– 14 –
English
6. When the tension adjustment is completed, tighten
the lock nut (3) using a 10 mm or adjustable wrench
to secure.
7. Repeat the above steps for the other saw mounting
bracket.
NOTE: The power cord clamp (5) is removed for better
illustration.
Fig. R
1
52
3
4
6

– 15 –
English
OPERATION INSTRUCTIONS
Take care during setting up and folding the stand to
reduce the hazard of pinching hands and ngers.
SETTING UP THE STAND (FIG. S)
1. Lift the stand to its upright position.
2. Unfold the stand by stepping on the foot pedal (1)
to release the locking treadle hook, and press down
on stand handles (2) until the stand is in its lowest
position.
NOTE: You should hear a click when locked in place.
● Do not mount the miter saw unless the stand top is
securely locked.
● To reduce the risk of pinching hands and ngers,
be aware of doing every operation while raising or
lowering the stand.
● To prevent injury, be sure to grab the stand handles
BY BOTH HANDS while raising or lowering the
stand.
Fig. S
FOLDING THE STAND (FIG. T)
1. Hold the stand handles with BOTH HANDS and
press two stand locking levers (3) to release the
locking treadle hook.
2. Slowly lift the stand handles up until you hear a
click from the foot pedal (1) locked in place so that
the stand is folded in its upright position as shown
in Fig. T.
● Before folding the stand, remove the miter saw from
the stand together with the mounting brackets by two
or more people.
● Be sure to hear a click when locked in place before
you move the stand.
● If the stand cannot be locked, check the installation
of the bumper and re-install it. If the lock is still not
working, please contact a metabo HPT authorized
service center.
Fig. T
OPERATION
WARNING
WARNING
1
2
Upright position Lowest position
WARNING
3
1
Upright position

– 16 –
English
GENERAL MAINTENANCE
Remove the miter saw when servicing or cleaning the
stand. Use clean cloths to remove dirt, dust, oil, grease
etc. Avoid using solvents when cleaning plastic parts.
Most plastics are susceptible to damage from various
types of commercial solvents and may be damaged by
their use.
Do not use the brake uids, gasoline, petroleum-based
products, penetrating oils and so on to contact with
plastic parts. Chemical can damage, weaken or destroy
plastic which may cause serious personal injury.
● If any part of the stand is not operating properly,
stop using the stand and have it serviced by a
metabo HPT authorized service center.
●When servicing the stand, use only identical
metabo HPT replacement parts. Use any other parts
may cause hazards or product damage.
● Repairs should be conducted only by a metabo HPT
authorized service center.
●Always wear safety goggles or safety glasses
with side shields and dust mask during miter saw
operation or when blowing dust.
● Occasionally check the saw mounting brackets,
making sure the mounting brackets are tight by
following “ADJUSTING THE SAW MOUNTING
BRACKETS” on page 13.
TRANSPORTATION AND STORAGE (FIG. T, U)
For transportation and storage usage, follow the
instruction in section “FOLDING THE STAND” on page
15. Be sure to hear a click when the stand is folded up
and hold the stand handles with both hands securely.
The stand should be in its upright position as shown in
Fig. T. To be ready for storage or transportation, please
refer to Fig. U for proper transporting position.
● Do not transport the unfolded stand with a miter saw
mounted on it.
● Before transporting or storing the stand, you MUST
remove the miter saw from the stand.
● When carrying the stand in a vehicle, securely tie it
down to prevent movement and possible damage.
● When storing the stand, never lean the stand against
wall.
WARNING
Fig. U
MAINTENANCE
WARNING
WARNING

– 17 –
Français
SÉCURITÉ GÉNÉRALE
AVERTISSEMENT
●Le non-respect de ces règles peut provoquer des blessures corporelles graves.
●Pour réduire tout risque de blessure, gardez vos deux mains sur les poignées du support lorsque vous levez ou
abaissez le support.
●Avant de plier le support, la scie à onglet DOIT être retirée du support.
●Utiliser uniquement avec des supports de xation metabo HPT. Les supports de xation proposés par d'autres
marques que metabo HPT n'ont pas été testés avec ce support et leur utilisation peut être dangereuse.
Veillez à lire et comprendre la totalité de ce manuel avant toute tentative de montage, d'utilisation ou d'installation du
produit. Ces consignes de sécurité ne couvrent pas de façon exhaustive toutes les situations possibles.
DÉFINITION DES SYMBOLES
● AVERTISSEMENT indique une situation de risque qui, sans l'éviter, peut entraîner la mort ou des blessures
graves.
● ATTENTION indique une situation de risque qui, sans l'éviter, peut entraîner des blessures mineures ou
graves, ou peut endommager la machine.
● REMARQUE indique une information importante.
INFORMATIONS GÉNÉRALES DE SÉCURITÉ
Veillez à lire et comprendre tous les avertissements et les instructions avant d'utiliser un outil ou de
l'équipement. L'utilisation d'outils ou d'équipement exige toujours de respecter les précautions de sécurité de
base an de réduire le risque de blessure corporelle. L'utilisation, l'entretien et toute modication inappropriés
des outils ou de l'équipement peuvent entraîner des blessures graves et causer des dégâts matériels. Les
outils et l'équipement sont conçus pour certaines applications spéciques. N'altérez pas le support et ne
l'utilisez pas à toute n autre que l'usage qui en est prévu.
AVERTISSEMENT

– 18 –
Français
SÉCURITÉ DU SUPPORT POUR SCIE À ONGLET
CONSIGNES DE SÉCURITÉ RELATIVES À L'UTILISATION DU SUPPORT POUR SCIE À ONGLET
●Tenir hors de portée des enfants. Tous les visiteurs doivent se tenir à une distance sûre de l'espace de travail.
● Toujours nettoyer l'espace de travail. Les zones de travail et les établis encombrés sont propices aux accidents.
●Avant d'utiliser le support, s'assurer qu'aucune pièce n'est endommagée ou déformée.
●Avant d'utiliser le support, s'assurer que toutes les pièces et les composants sont correctement installés.
●Ne pas utiliser dans un environnement dangereux. Ne pas utiliser le support dans des endroits humides, mouillés
ou exposés à la pluie. L'espace de travail doit être bien éclairé.
● Toujours utiliser le support sur une surface plane et à niveau. Ne pas l'utiliser sur une surface irrégulière ou instable.
Ne pas utiliser le support sur une surface glissante. Ceci réduira signicativement la capacité de charge du support.
●Le support est conçu pour servir de support aux scies à onglet metabo HPT et tolère une charge maximale de
136 kg (300 lb). Le poids total de la scie à onglet et de la pièce à couper ne doit pas dépasser la capacité de ce
support. Une mauvaise utilisation ou un usage abusif peut endommager le matériel ou entraîner des blessures
corporelles.
● Ne pas s'asseoir ou monter sur le support. Ne pas suspendre ou insérer tout objet autre que la scie à onglet.
● Ne pas altérer le support, et ne pas l'utiliser à toute autre n qu'au montage d'une scie à onglet metabo HPT.
●Le support doit uniquement être utilisé avec des scies à onglet metabo HPT dont la lame possède un diamètre
maximal de 305 mm (12 po). Toutefois, le support est incompatible avec C12FSA.
●La scie à onglet doit être solidement xée au support, conformément aux consignes du manuel d'instructions.
●Aligner la position et ajuster l'équilibre de la scie à onglet conformément au manuel d'instructions après avoir xé la
scie à onglet au support.
●En levant et en abaissant le support, veiller à réduire tout risque de pincement des mains et des doigts.
● Débrancher la prise d'alimentation du réceptacle lors du montage ou du démontage de la scie à onglet du support.
●Pour votre sécurité, xer la scie à onglet au support avec l'aide de deux personnes ou plus.
●Lors de la xation de la scie à onglet sur le support, maintenir la scie à onglet fermement entre les mains jusqu'à
ce que les verrous du support de xation soient sécurisés pour éviter que la scie à onglet ne tombe des rails du
support.
●Après avoir xé la scie à onglet sur le support, veiller à ce que le support ne se renverse pas ou ne soit pas
accidentellement déplacé par les vibrations, le vent, les chocs ou autres forces externes. Si cela est impossible, la
stabilité peut être obtenue en suivant des mesures de sécurité spéciques. Par exemple, en ancrant solidement le
support au sol ou dans les fondations.
●Contrôler régulièrement le support et la scie à onglet, en vériant le montage approprié de la scie à onglet. Un
support mal serré est instable et peut se renverser en causant des blessures graves.
● Avant d'utiliser la scie à onglet montée, lire attentivement le manuel d'instructions de la scie à onglet.
●Avant d'utiliser la scie à onglet, vérier que les loquets des deux supports de xation sont bien attachés et que la
scie à onglet est correctement xée au support.
● Pour éviter que la scie à onglet ne tombe du support, disposer proprement le cordon d'alimentation au sol pour
empêcher qu'un opérateur ou un visiteur ne trébuche sur le câble.
● Porter des vêtements de travail appropriés. Ne pas porter de vêtements amples, de gants, de cravates, de
bagues, de bracelets, ou autres bijoux pouvant être pris dans les pièces en mouvement. Le port de chaussures
antidérapantes est recommandé. Recouvrir les cheveux longs d'un accessoire de protection.
● Toujours porter une protection oculaire à écrans latéraux conforme à la norme ANSI Z87.1, pour éviter toute
blessure aux yeux lors de l'utilisation de la scie à onglet. Les lunettes de vue ordinaires ne constituent pas une
protection adéquate, car elles ne contiennent pas de verre de sécurité résistant aux impacts. Porter un masque
protecteur ou antipoussière si la découpe engendre la production de poussière.
● Ne pas se pencher. Toujours se tenir bien campé et en équilibre.
● Lors de la découpe d'une grande pièce en bois, vérier la bonne position de support du matériau, car le matériau
coupé peut perdre son équilibre et tomber du support. Si la pièce s'étend au-delà du support de travail, le pied
opposé du support risque de se soulever soudainement en raison de la mauvaise répartition du poids. Pour éviter
cette situation, tenir fermement le côté opposé et utiliser un support additionnel avant de commencer la découpe.

– 19 –
Français
CONSERVEZ CES INSTRUCTIONS ET METTEZ-LES À LA DISPOSITION DES AUTRES
UTILISATEURS ET PROPRIÉTAIRES DE CE SUPPORT.
DÉBALLAGE DU SUPPORT
Ce produit doit être assemblé.
1. Retirez le support et toutes ses pièces de leur emballage.
2. Placez le support au sol.
3. Séparez les pièces de l'emballage. Comparez chaque pièce avec la liste ci-dessous et l'illustration de la page 20
pour vérier que tous les éléments sont présents avant de jeter l'emballage.
Si une pièce est manquante ou endommagée, n'essayez pas de monter le support tant que cette pièce n'est pas
remplacée.
TABLEAU DES PIÈCES DÉTACHÉES
CONTENU DE L'EMBALLAGE
REMARQUE : si des pièces sont manquantes ou endommagées, veuillez contacter metabo HPT au 1 800 546-
1666 pour obtenir de l'aide.
● Pour détacher la scie du support, vérier que la tête de coupe est tirée vers l'arrière et verrouillée en position
inférieure, puis débloquer les verrous du support de xation tout en maintenant la scie à onglet fermement entre les
mains pour éviter que celle-ci ne tombe des rails du support. Retirer soigneusement la scie à onglet et les supports
de xation avec l'aide d'au moins deux personnes.
● Lors du transport du support en véhicule, attacher fermement celui-ci pour empêcher tout mouvement et tout
dommage éventuel.
● Pour réduire tout risque de blessure, vérier régulièrement que les attaches sont bien xées et ajustées
conformément aux instructions de montage incluses dans ce manuel.
● En cas de malfonction d’une pièce de l’établi, il doit être réparé avant son utilisation. Lors de la réparation du
support, utiliser uniquement des pièces de rechange metabo HPT identiques. Les réparations doivent uniquement
être effectuées par un centre de réparation metabo HPT agréé.
AVERTISSEMENT
ÉLÉMENT DESCRIPTION QUANTITÉ
A Support 1
B Pied droit du support 1
C Poignée du support 2
DTube de pied d’établi avec garniture de pied 1
ESupport de xation de la scie à onglet 2
FSupport de xation auxiliaire 2
GTube de pied d’établi avec garniture réglable de pied 1
H Support d’extension gauche 1
ISupport d’extension droit 1
J Guide (gauche et droit) 2
KPoignée de verrouillage de l'ensemble du support d'extension 1
LSac d’accessoires de montage de la poignée d’établi 1
MSac d’accessoires de montage du pied d’établi 1
NSac d’accessoires de montage de la barre de jonction 1
OSac d’accessoires de montage de la pare-chocs 1
PPlaque d'ancrage 1
QSac d’quincaillerie du support de xation auxiliaire 1
RSac d’quincaillerie de montage des roues 1
S Roue 2

– 20 –
Français
DÉBALLAGE ET CONTRÔLE DU CONTENU
L
R
A
HAUT
GAUCHE DROITE
BAS
B C
FD
G
E
K-Support d’extension L-Poignée d’établi M-Pied d’établi
H
N-Barre de jonction O-Montage de la pare-chocs P-Plaque d’ancrage
I J
Q-Support de xation auxiliaire R-Montage des roues S