METREL EurotestXE User manual

EurotestXE
MI 3102H BT
MI 3102 BT
Instruction manual
Version 1.3, Code no. 20 752 130

2
Distributor:
Manufacturer:
METREL d.d.
Ljubljanska cesta 77
1354 Horjul
Slovenia
web site: http://www.metrel.si
e-mail: [e-mail]
Mark on your equipment certifies that it meets requirements of all subjected EU regulations
© 2018 METREL
The trade names Metrel, Smartec, Eurotest, Autosequence are trademarks registered or pending in
Europe and other countries.
No part of this publication may be reproduced or utilized in any form or by any means without
permission in writing from METREL.

MI 3102(H) BT EurotestXE Table of contents
3
Table of Contents
1Preface...............................................................................................................................6
2Safety and operational considerations ...........................................................................7
2.1 Warnings and notes ....................................................................................................7
2.2 Battery and charging.................................................................................................11
2.3 Standards applied.....................................................................................................13
3Instrument description...................................................................................................14
3.1 Front panel................................................................................................................14
3.2 Connector panel........................................................................................................15
3.3 Back side ..................................................................................................................16
3.4 Carrying the instrument.............................................................................................18
3.5 Instrument set and accessories.................................................................................18
3.5.1 Standard set MI 3102H BT –EurotestXE ..............................................................18
3.5.2 Standard set MI 3102 BT –EurotestXE.................................................................19
3.5.3 Optional accessories.............................................................................................19
4Instrument operation......................................................................................................20
4.1 Display and sound.....................................................................................................20
4.1.1 Terminal voltage monitor.......................................................................................20
4.1.2 Battery indication...................................................................................................20
4.1.3 Messages..............................................................................................................20
4.1.4 Results..................................................................................................................21
4.1.5 Sound warnings.....................................................................................................21
4.1.6 Help screens.........................................................................................................22
4.1.7 Backlight and contrast adjustments.......................................................................22
4.2 Function selection.....................................................................................................23
4.3 Instruments main menu.............................................................................................24
4.4Settings.....................................................................................................................24
4.4.1 Memory.................................................................................................................25
4.4.2 Language..............................................................................................................25
4.4.3 Date and time........................................................................................................25
4.4.4 Earthing system (MI 3102 BT only)........................................................................26
4.4.5 RCD testing...........................................................................................................26
4.4.6 Isc factor................................................................................................................28
4.4.7 Commander support..............................................................................................29
4.4.8 Initial settings ........................................................................................................29
4.4.9 Clamp Settings......................................................................................................31
4.4.10 Length units.......................................................................................................32
5Measurements.................................................................................................................33
5.1 Voltage, frequency and phase sequence...................................................................33
5.2 Insulation resistance..................................................................................................35
5.3 The DAR and PI diagnostic (MI 3102H BT only)........................................................37
5.4 Resistance of earth connection and equipotential bonding........................................39
5.4.1 R LOWΩ, 200 mA resistance measurement..........................................................39
5.4.2 Continuous resistance measurement with low current...........................................41
5.4.3 Compensation of test leads resistance..................................................................42
5.5 Testing RCDs............................................................................................................43
5.5.1 Contact voltage (RCD Uc).....................................................................................44
5.5.2 Trip-out time (RCDt)..............................................................................................45

MI 3102(H) BT EurotestXE Table of contents
4
5.5.3 Trip-out current (RCD I).........................................................................................46
5.5.4 RCD Auto-test.......................................................................................................47
5.6 Fault loop impedance and prospective fault current...................................................49
5.7 Line impedance and prospective short-circuit current / Voltage drop.........................51
5.7.1 Line impedance and prospective short circuit current............................................52
5.7.2 Voltage drop..........................................................................................................53
5.8 Earth resistance........................................................................................................56
5.8.1 Standard earthing resistance measurement..........................................................57
5.8.2 Contactless earthing resistance measurement (with two current clamps)..............58
5.8.3 Specific earth resistance measurement.................................................................59
5.9 PE test terminal.........................................................................................................60
5.10 Power........................................................................................................................62
5.11 Harmonics.................................................................................................................64
5.12 Current......................................................................................................................65
5.13 First fault leakage current –ISFL (MI 3102 BT only)..................................................66
5.14 Testing of insulation monitoring devices –IMD (MI 3102 BT only).............................68
5.15 PE conductor resistance ...........................................................................................71
5.16 Illumination................................................................................................................72
6Auto-sequences..............................................................................................................74
7Data handling..................................................................................................................79
7.1 Memory organization.................................................................................................79
7.2 Data structures..........................................................................................................79
7.3 Storing test results ....................................................................................................80
7.4 Recalling test results.................................................................................................81
7.5Clearing stored data..................................................................................................82
7.5.1 Clearing complete memory content.......................................................................82
7.5.2 Clearing measurement(s) in selected location.......................................................82
7.5.3 Clearing individual measurements.........................................................................83
7.5.4 Renaming installation structure elements (upload from PC) ..................................83
7.5.5 Renaming installation structure elements with serial barcode reader or RFID reader
84
7.6 Communication.........................................................................................................85
7.6.1 USB and RS232 communication...........................................................................85
7.6.2 Bluetooth communication......................................................................................86
8Upgrading the instrument ..............................................................................................87
9Maintenance....................................................................................................................88
9.1 Fuse replacement .....................................................................................................88
9.2 Cleaning....................................................................................................................88
9.3 Periodic calibration....................................................................................................88
9.4 Service......................................................................................................................88
10 Technical specifications.................................................................................................89
10.1 Insulation resistance..................................................................................................89
10.2 Diagnostic test (MI 3102H BT only)...........................................................................90
10.3 Continuity..................................................................................................................90
10.3.1 Resistance R LOW............................................................................................90
10.3.2 Resistance CONTINUITY..................................................................................90
10.4 RCD testing...............................................................................................................91
10.4.1 General data......................................................................................................91
10.4.2 Contact voltage RCD Uc....................................................................................92
10.4.3 Trip-out time......................................................................................................92
10.4.4 Trip-out current..................................................................................................92

MI 3102(H) BT EurotestXE Table of contents
5
10.5 Fault loop impedance and prospective fault current...................................................93
10.5.1 No disconnecting device or FUSE selected.......................................................93
10.5.2 RCD selected....................................................................................................93
10.6 Line impedance and prospective short-circuit current / Voltage drop.........................94
10.7 PE conductor resistance ...........................................................................................95
10.7.1 No RCD selected...............................................................................................95
10.7.2 RCD selected....................................................................................................95
10.8 Resistance to earth...................................................................................................96
10.8.1 Standard earthing resistance measurement –3-wire measurement ..................96
10.8.2 Contactless earthing resistance measurement using two current clamps..........96
10.8.3 Specific earth resistance measurements...........................................................97
10.9 Voltage, frequency, and phase rotation.....................................................................98
10.9.1 Phase rotation...................................................................................................98
10.9.2 Voltage..............................................................................................................98
10.9.3 Frequency .........................................................................................................98
10.9.4 Online terminal voltage monitor.........................................................................98
10.10 TRMS Clamp current.................................................................................................99
10.11 Power tests.............................................................................................................100
10.12 First fault leakage current –ISFL (MI 3102 BT only)................................................101
10.13 Calibrated resistance for IMD testing (MI 3102 BT only)..........................................101
10.14 Illumination..............................................................................................................102
10.14.1 Illumination (Luxmeter sensor, type B).............................................................102
10.14.2 Illumination (Luxmeter sensor, type C) ............................................................102
10.15 General data...........................................................................................................103
Appendix A –Fuse table –IPSC.........................................................................................104
Appendix B –Accessories for specific measurements.....................................................108
Appendix C –Country notes................................................................................................110
C.1 List of country modifications....................................................................................110
C.2 AT modification –G type RCD ................................................................................110
C.3 Modification of the chapter 5.5.1..............................................................................111
Appendix D –Commanders (A 1314, A 1401).....................................................................112
D.1 Warnings related to safety................................................................................112
D.2 Battery.....................................................................................................................112
D.3 Description of commanders.....................................................................................112
D.4 Operation of commanders.......................................................................................113

MI 3102(H) BT EurotestXE Preface
6
1 Preface
Congratulations on your purchase of the Eurotest instrument and its accessories from METREL.
The instrument was designed on a basis of rich experience, acquired through many years of
dealing with electric installation test equipment.
The Eurotest instrument is a professional, multifunctional, hand-held test instrument intended to
perform all the measurements on a.c. electrical LV installations.
The following measurements and tests can be performed:
Voltage and frequency,
Continuity tests,
Insulation resistance tests,
Diagnostic tests (MI 3102H BT only),
RCD testing,
Fault loop / RCD trip-lock impedance measurements,
Line impedance / Voltage drop,
Phase sequence,
Earth resistance tests,
Current measurements,
Power and harmonics measurements,
Illumination,
First fault current (MI 3102 BT only),
Testing of insulation monitoring devices –IMD (MI 3102 BT only) and
Pre-defined auto-sequences.
The graphic display with backlight offers easy reading of results, indications, measurement
parameters and messages. Two LED PASS/FAIL indicators are placed at the sides of the LCD.
The operation of the instrument is designed to be as simple and clear as possible and no
special training (except for the reading this instruction manual) is required in order to begin
using the instrument.
In order for operator to be familiar enough with performing measurements in general and their
typical applications it is advisable to read METREL handbook Guide for testing and
verification of low voltage installations.
The instrument is equipped with the entire necessary accessory for comfortable testing.

MI 3102(H) BT EurotestXE Safety and operational considerations
7
2 Safety and operational considerations
2.1 Warnings and notes
In order to maintain the highest level of operator safety while carrying out various tests and
measurements, METREL recommends keeping your Eurotest instruments in good condition
and undamaged. When using the instrument, consider the following general warnings:
General warnings related to safety:
The symbol on the instrument means »Read the Instruction manual with
special care for safe operation«. The symbol requires an action!
If the test equipment is used in a manner not specified in this user manual, the
protection provided by the equipment could be impaired!
Read this user manual carefully, otherwise the use of the instrument may be
dangerous for the operator, the instrument or for the equipment under test!
Do not use the instrument or any of the accessories if any damage is noticed!
Consider all generally known precautions in order to avoid risk of electric shock
while dealing with hazardous voltages!
In case a fuse has blown follow the instructions in this manual in order to replace
it! Use only fuses that are specified!
Do not use the instrument in AC supply systems with voltages higher than
550 Va.c.
Service, repairs or adjustment of instruments and accessories is only allowed to
be carried out by a competent authorized personnel!
Use only standard or optional test accessories supplied by your distributor!
Consider that protection category of some accessories is lower than of the
instrument. Test tips and Tip commander have removable caps. If they are
removed the protection falls to CAT II. Check markings on accessories!
cap off, 18 mm tip: CAT II up to 1000 V
cap on, 4 mm tip: CAT II 1000 V / CAT III600 V / CAT IV300 V
The instrument comes supplied with rechargeable Ni-MH battery cells. The cells
should only be replaced with the same type as defined on the battery
compartment label or as described in this manual. Do not use standard alkaline
battery cells while the power supply adapter is connected, otherwise they may
explode!
Hazardous voltages exist inside the instrument. Disconnect all test leads, remove
the power supply cable and switch off the instrument before removing battery
compartment cover.
Do not connect any voltage source on C1 input. It is intended only for connection
of current clamps. Maximal input voltage is 3 V!

MI 3102(H) BT EurotestXE Safety and operational considerations
8
All normal safety precautions must be taken in order to avoid risk of electric
shock while working on electrical installations!
Warnings related to safety of measurement functions:
Insulation resistance
Insulation resistance measurement should only be performed on de-energized objects!
Do not touch the test object during the measurement or before it is fully discharged! Risk
of electric shock!
When an insulation resistance measurement has been performed on a capacitive object,
automatic discharge may not be done immediately! The warning message and the
actual voltage are displayed during discharge until voltage drops below 30 V.
Do not connect test terminals to external voltage higher than 600 V (AC or DC) in order
not to damage the test instrument!
Continuity functions
Continuity measurements should only be performed on de-energized objects!
Parallel loops may influence on test results.
Testing PE terminal
If phase voltage is detected on the tested PE terminal, stop all measurements
immediately and ensure the cause of the fault is eliminated before proceeding with any
activity!
Notes related to measurement functions:
General
The indicator means that the selected measurement cannot be performed because
of irregular conditions on input terminals.
Insulation resistance, continuity functions and earth resistance measurements can only
be performed on de-energized objects.
PASS / FAIL indication is enabled when limit is set. Apply appropriate limit value for
evaluation of measurement results.
In the case that only two of the three wires are connected to the electrical installation
under test, only voltage indication between these two wires is valid.
Insulation resistance
The standard three-wire test lead, schuko test cable or Plug / Tip commanders can be
used for the insulation test with voltages ≤ 1kV.
The special two wire 2.5 kV test lead must be used for the insulation test with 2.5 kV. (MI
3102H BT only).
If a voltage of higher than 30 V (AC or DC) is detected between test terminals, the
insulation resistance measurement will not be performed.
The instrument automatically discharge tested object after finished measurement.
A double click of TEST key starts a continuous measurement.
Continuity functions

MI 3102(H) BT EurotestXE Safety and operational considerations
9
If a voltage of higher than 10 V (AC or DC) is detected between test terminals, the
continuity resistance test will not be performed.
Compensate test lead resistance before performing a continuity measurement, where
necessary.
Earth resistance - RE, two clamps, specific earth resistance ()
If voltage between test terminals is higher than 30 V the resistance to earth
measurement will not be performed.
If a noise voltage higher than approx. 5 V is present between the H and E or S test
terminals,“” (noise) warning symbol will be displayed, indicating that the test result may
not be correct!
For two clamps earth resistance measurement clamps A 1018 and A 1019 should be
used. Clamps A 1391 are not supported.
For specific earth resistance measurements Adaptor A 1199 should be used.
RCD functions
Parameters set in one function are also kept for other RCD functions!
The measurement of contact voltage does not normally trip an RCD. However, the trip
limit of the RCD may be exceeded as a result of leakage current flowing to the PE
protective conductor or a capacitive connection between L and PE conductors.
The RCD trip-lock sub-function (function selector in LOOP position) takes longer to
complete but offers much better accuracy of fault loop resistance (in comparison to the
RLsub-result in Contact voltage function).
RCD trip-out time and RCD trip-out current measurements will only be performed if the
contact voltage in the pre-test at nominal differential current is lower than the set contact
voltage limit!
The auto-test sequence (RCD AUTO function) stops when trip-out time is out of
allowable time period.
Z-LOOP
The low limit prospective short-circuit current value depends on fuse type, fuse current
rating, fuse trip-out time and impedance scaling factor.
The specified accuracy of tested parameters is valid only if the mains voltage is stable
during the measurement.
Fault loop impedance measurements will trip an RCD.
The measurement of fault loop impedance using trip-lock function does not normally trip
an RCD. However, the trip limit may be exceeded if a leakage current flows to the PE
protective conductor or if there is a capacitive connection between L and PE conductors.
Z-LINE / Voltage drop
In case of measurement of ZLine-Line with the instrument test leads PE and N connected
together the instrument will display a warning of dangerous PE voltage. The
measurement will be performed anyway.
Specified accuracy of tested parameters is valid only if mains voltage is stable during the
measurement.
L and N test terminals are reversed automatically according to detected terminal voltage
(except in UK version).
Power / Harmonics / Current

MI 3102(H) BT EurotestXE Safety and operational considerations
10
Before starting any power measurement the current clamp settings in Settings menu
should be checked. Select appropriate current clamp model and measuring range that
are best fitted to the expected current values.
Consider polarity of current clamp (arrow on test clamp should be oriented toward
connected load), otherwise result will be negative!
Illumination
For accurate measurement make sure that the milk glass bulb is lit without any shadows
cast by hand, body or other unwanted objects.
It is very important to know that the artificial light sources reach full power of operation
after a period of time (see technical data for light sources) and should be therefore
switched on for this period of time before the measurements are taken.
Testing PE terminal
PE terminal can be tested in RCD, LOOP and LINE function selector positions only!
For correct testing of PE terminal, the TEST key has to be touched for a few seconds.
Make sure to stand on non-isolated floor while carrying out the test, otherwise test result
may be wrong!
PE conductor resistance
The specified accuracy of tested parameters is valid only if the mains voltage is stable
during the measurement.
PE conductor resistance measurement will trip an RCD.
The measurement of PE conductor resistance using trip-lock function does not normally
trip an RCD. However, the trip limit may be exceeded if a leakage current flows to the
PE protective conductor or if there is a capacitive connection between L and PE
conductors.
Testing of Insulation monitoring devices (IMD) (MI 3102 BT only)
It is recommended to disconnect all appliances from the tested supply to receive regular
test results. Any connected appliance will influence the insulation resistance threshold
test.
The displayed resistances and currents are indicative only. Displayed resistance can
significantly differ from the actual resistance the Eurotest simulates. If IMD’s with very
low test currents (below 1mA) are checked the displayed resistance value is typically
lower (and current higher) than the actual simulated resistance. The difference is lower
for lower set resistances.
Auto-sequence tests
See notes related to tests / measurements of selected auto-sequence.

MI 3102(H) BT EurotestXE Safety and operational considerations
11
2.2 Battery and charging
The instrument uses six AA size alkaline or rechargeable Ni-MH battery cells. Nominal
operating time is declared for cells with nominal capacity of 2100 mAh. Battery condition is
always displayed in the lower right display part. In case the battery is too weak the instrument
indicates this as shown in figure 2.1. This indication appears for a few seconds and then the
instrument turns itself off.
Figure 2.1: Discharged battery indication
The battery is charged whenever the power supply adapter is connected to the instrument. The
power supply socket polarity is shown in figure 2.2. Internal circuit controls charging and
assures maximum battery lifetime.
+
-
Figure 2.2: Power supply socket polarity
Symbols:
Indication of battery charging
Figure 2.3: Charging indication
Warnings related to safety:
When connected to an installation, the instruments battery compartment can contain
hazardous voltage inside! When replacing battery cells or before opening the
battery/fuse compartment cover, disconnect any measuring accessory connected to the
instrument and turn off the instrument,
Ensure that the battery cells are inserted correctly otherwise the instrument will not
operate and the batteries could be discharged.
Do not recharge alkaline battery cells!
Use only power supply adapter delivered from the manufacturer or distributor of the test
equipment !
Notes:
The charger in the instrument is a pack cell charger. This means that the battery cells
are connected in series during the charging. The battery cells have to be equivalent
(same charge condition, same type and age).
If the instrument is not to be used for a long period of time, remove all batteries from the
battery compartment.
Alkaline or rechargeable Ni-MH batteries (size AA) can be used. METREL recommends
only using rechargeable batteries with a capacity of 2100mAh or above.
Unpredictable chemical processes can occur during the charging of battery cells that
have been left unused for a longer period (more than 6 months). In this case METREL
recommends repeating the charge/discharge cycle at least 2-4 times.
If no improvement is achieved after several charge / discharge cycles, then each battery
cell should be checked (by comparing battery voltages, testing them in a cell charger,
etc). It is very likely that only some of the battery cells are deteriorated. One different
battery cell can cause an improper behaviour of the entire battery pack!

MI 3102(H) BT EurotestXE Safety and operational considerations
12
The effects described above should not be confused with the normal decrease of battery
capacity over time. Battery also loses some capacity when it is repeatedly charged /
discharged. This information is provided in the technical specification from battery
manufacturer.

MI 3102(H) BT EurotestXE Safety and operational considerations
13
2.3 Standards applied
The Eurotest instruments are manufactured and tested in accordance with the following
regulations:
Electromagnetic compatibility (EMC)
EN 61326
Electrical equipment for measurement, control and laboratory
use –EMC requirements
Class B (Hand-held equipment used in controlled EM environments)
Safety (LVD)
EN 61010-1
Safety requirements for electrical equipment for measurement, control and
laboratory use –Part 1: General requirements
EN 61010-2-030
Safety requirements for electrical equipment for measurement, control and
laboratory use –Part 2-030: Particular requirements for testing and
measuring circuits
EN 61010-031
Safety requirements for electrical equipment for measurement, control and
laboratory use –Part 031: Safety requirements for hand-held probe
assemblies for electrical measurement and test
EN 61010-2-032
Safety requirements for electrical equipment for measurement, control, and
laboratory use - Part 2-032: Particular requirements for hand-held and hand-
manipulated current sensors for electrical test and measurement
Functionality
EN 61557
Electrical safety in low voltage distribution systems up to 1000 VAC and 1500
VAC –Equipment for testing, measuring or monitoring of protective measures
Part 1: General requirements
Part 2: Insulation resistance
Part 3: Loop resistance
Part 4: Resistance of earth connection and equipotential bonding
Part 5: Resistance to earth
Part 6: Residual current devices (RCDs) in TT and TN systems
Part 7: Phase sequence
Part 10: Combined measuring equipment
Part 12: Performance measuring and monitoring devices (PMD)
DIN 5032
Photometry
Part 7: Classification of illuminance meters and luminance meters
Reference standards for electrical installations and components
EN 61008
Residual current operated circuit-breakers without integral overcurrent
protection for household and similar uses
EN 61009
Residual current operated circuit-breakers with integral overcurrent
protection for household and similar uses
IEC 60364-4-41
Electrical installations of buildings Part 4-41 Protection for safety –
protection against electric shock
BS 7671
IEE Wiring Regulations (17th edition)
AS/NZS 3017
Electrical installations –Verification guidelines
Note about EN and IEC standards:
Text of this manual contains references to European standards. All standards of EN
6XXXX (e.g. EN 61010) series are equivalent to IEC standards with the same number
(e.g. IEC 61010) and differ only in amended parts required by European harmonization
procedure.

MI 3102(H) BT EurotestXE Instrument description
14
3 Instrument description
3.1 Front panel
Figure 3.1: Front panel
Legend:
1
LCD
128 x 64 dots matrix display with backlight.
2
UP
Modifies selected parameter.
3
DOWN
4
TEST
TEST
Starts measurements.
Acts also as the PE touching electrode.
5
ESC
Goes one level back.
6
TAB
Selects the parameters in selected function.
7
Backlight
Contrast
Changes backlight level and contrast.
8
ON / OFF
Switches the instrument power on or off.
The instrument automatically turns off 15 minutes after the last key
was pressed.
9
HELP / CAL
Accesses help menus.
Calibrates test leads in Continuity functions.
Starts ZREF measurement in Voltage drop sub-function.
10
Function selector
- RIGHT
Selects test / measurement function.
11
Function selector
- LEFT
12
MEM
Stores / recalls memory of instrument.
Stores clamp settings.
13
Green LEDs
Red LEDs
Indicates PASS / FAIL of result.

MI 3102(H) BT EurotestXE Instrument description
15
3.2 Connector panel
Figure 3.2: Connector panel
Legend:
1
Test connector
Measuring inputs / outputs.
2
Charger socket
3
USB connector
Communication with PC USB (1.1) port.
4
Protection cover
5
C1
Current clamp measuring input
6
PS/2 connector
Communication with PC serial port
Connection to optional measuring adapters
Connection to barcode / RFID reader
Warnings!
Maximum allowed voltage between any test terminal and ground is 600 V!
Maximum allowed voltage between test terminals on test connector is 600 V!
Maximum allowed voltage on test terminal C1 is 3 V!
Maximum short-term voltage of external power supply adapter is 14 V!

MI 3102(H) BT EurotestXE Instrument description
16
3.3 Back side
12
3
Figure 3.3: Back panel
Legend:
1
Battery / fuse compartment cover
2
Back panel information label
3
Fixing screws for battery / fuse compartment cover
Figure 3.4: Battery and fuse compartment
Legend:
1
Fuse F1
M 315 mA / 250 V
2
Fuses F2 and F3
F 4 A / 500 V (breaking capacity 50 kA)
3
Serial number label
4
Battery cells
Size AA, alkaline / rechargeable NiMH

MI 3102(H) BT EurotestXE Instrument description
17
3
1
2
R: 0.0 1999 Test current: max. 8.5mA
Open-circuit voltage: 6.5V
Continuity 7mA
R: 0.18M 199.9M , U =50V ,100 ,
R: 0.12M 999M , U = 500V , 1kV
U: 0V 1200V
Nominal voltages: 100V , 250V , 500V , 1kV
Measuring current: min. 1mA at R =U 1k /V
Short-circuit current: < 3mA
N
N
N N
Insulation resistance (EN 61557-2)
V 250V
Continuity
Tripping time
non-delayed (time-delayed) RCDs
1: 0ms 300ms (500ms)
2 : 0ms 150ms (200ms)
5 : 0ms 40ms (150ms), U : 0.0V 100.0V C
Tripping current
I : 0.2 I 1.1 I AC (
t : 0ms 300ms, U : 0.0V 100.0V C
N N N 1.5 I A)
Multiplier: 0.5, 1, 2, 5
Contact voltage
U : 0.0V 100.0V
R : 0.00 10.00k (R =U / I )
C
S S C N
R : 0. 1999 I : 0. A . kAL-N(L) PSC17 20 1 4
Nominal voltage: 100V 440V/ 15Hz 500Hz
Line impedance (EN 61557-3)
Fault loop (EN 61557-3)
R : 0. 1999
I : 0. A . kA PFC 14 1 4
Nominal voltage: 100V 264V/ 15Hz 500Hz
impedance
L-PE 17
Voltage, frequency
U: 0V 440V / f: 15Hz 500Hz
Phase rotation (EN 61557-7)
Nominal voltage: 100V 440V / 1 00
Results: 1.2.3 or 2.1.3
5Hz 5 Hz
RCD (EN 61557-6)
I : 10mA, 30mA, 100mA, 300mA, 500mA, 1A
Nominal voltage: 100V 264V/ 15Hz 500Hz
R Low (EN 61557-4)
R: 0.12 1999
Test current: min. ±200mA at 2
Open-circuit voltage: 6.5V 9.0V
Resistance to earth (EN 61557-5)
R: 0.04 9999
Open-circuit voltage:
Short-circuit current
< 45V
: < 20mA
RMS
Ljubljanska 77
SI - 1354 Horjul
Tel: [phone]
http://www.metrel.si
20 224 832
CAT III 600V
550V
Figure 3.5: Bottom
Legend:
1
Bottom information label
2
Neck belt openings
3
Handling side covers

MI 3102(H) BT EurotestXE Instrument description
18
3.4 Carrying the instrument
With the neck-carrying belt supplied in standard set, various possibilities of carrying the
instrument are available. Operator can choose appropriate one on basis of his operation, see
the following examples:
The instrument hangs around
operators neck
only –quick placing and
displacing.
The instrument can be used even when placed in soft
carrying bag –test cable connected to the instrument
through the front aperture.
3.5 Instrument set and accessories
3.5.1 Standard set MI 3102H BT –EurotestXE
Instrument
Soft carrying bag
Earth set 3-wire, 20 m
Plug commander
Test lead, 3 x 1.5 m
2.5 kV test lead, 2 x 1.5 m
Test probe, 3 pcs
Crocodile clip, 3 pcs
Set of carrying straps
RS232-PS/2 cable
USB cable
Set of Ni-MH battery cells
Power supply adapter
CD with instruction manual, “Guide for testing and verification of low voltage
installations” handbook and PC software EurolinkPRO.
Short instruction manual
Calibration Certificate

MI 3102(H) BT EurotestXE Instrument description
19
3.5.2 Standard set MI 3102 BT –EurotestXE
Instrument
Soft carrying bag
Earth set 3-wire, 20 m
Plug commander
Test lead, 3 x 1.5 m
Test probe, 3 pcs
Crocodile clip, 3 pcs
Set of carrying straps
RS232-PS/2 cable
USB cable
Set of Ni-MH battery cells
Power supply adapter
CD with instruction manual, “Guide for testing and verification of low voltage
installations” handbook and PC software EurolinkPRO.
Short instruction manual
Calibration Certificate
3.5.3 Optional accessories
See the attached sheet for a list of optional accessories that are available on request from your
distributor.

MI 3102(H) BT EurotestXE Instrument operation
20
4 Instrument operation
4.1 Display and sound
4.1.1 Terminal voltage monitor
The terminal voltage monitor displays on-line the voltages on the test terminals and information
about active test terminals in the a.c. installation measuring mode.
Online voltages are displayed together with test terminal indication. All three
test terminals are used for selected measurement.
Online voltages are displayed together with test terminal indication. L and N
test terminals are used for selected measurement.
L and PE are active test terminals; N terminal should also be connected for
correct input voltage condition.
Polarity of test voltage applied to the output terminals, L and N.
2.5 kV Insulation measurement terminal screen. (MI 3102H BT only)
4.1.2 Battery indication
The battery indication indicates the charge condition of battery and connection of external
charger.
Battery capacity indication.
Low battery.
Battery is too weak to guarantee correct result. Replace or
recharge the battery cells.
Charging in progress (if power supply adapter is connected).
4.1.3 Messages
In the message field warnings and messages are displayed.
Measurement is running, consider displayed warnings.
Conditions on the input terminals allow starting the measurement; consider
other displayed warnings and messages.
Conditions on the input terminals do not allow starting the measurement,
consider displayed warnings and messages.
RCD tripped-out during the measurement (in RCD functions).
Portable RCD selected (PRCD).
EV RCD selected (Electrical Vehicle RCD).
MI RCD selected (Mobile Installation RCD).