Omntec Proteus Series Owner's manual

SYSTEM PROGRAMMING
MANUAL
PART NO. OEL8000III-B, OEL8000III-K, & OEL8000III-X
SOFTWARE RELEASE 9.0 / 9.1
1. Open the camera app
2. Focus the camera on
the QR code by gently
tapping the code
3. Follow the instructions
on the screen to view
PDF file
PROTEUS
®
Series
TANK GAUGING SYSTEM
Revision 1.1
Document No. DOC00007 rev1.1
OMNTEC Mfg., Inc. has been certified
by DQS Inc. to ISO 9001:2015
OMNTEC Mfg., Inc. | 2420 Pond Road | Ronkonkoma | NY 11779 | [phone] | Email: [email protected]m | www.omntec.com

OMNTEC Mfg., Inc., 2420 Pond Road, Ronkonkoma, NY 11779
Phone [phone] Fax [phone] www.OMNTEC.com
File Name: DOC00007 rev1.1.docx 2 of 37 Rev Date: 12-14-2021
Programming Manual
OEL8000III Series
Table of Contents
Section # Page #
1. Navigating to Setup ............................................................................................................................................3
2. System Units .......................................................................................................................................................5
3. Printer Settings (PROTEUS K & X only) ...............................................................................................................6
4. Shift Time Settings ..............................................................................................................................................7
5. Misc. Settings......................................................................................................................................................8
6. Tank Parameters...............................................................................................................................................10
7. Tank Alarm Settings ..........................................................................................................................................12
8. Tank Table (Strapping)......................................................................................................................................13
9. Tank Drop and Other ........................................................................................................................................14
10. Tank Colors & Orientation ................................................................................................................................16
11. Copy Tank Parameters......................................................................................................................................17
12. BX-Sensor Control.............................................................................................................................................18
13. BX-Sensor Parameters ......................................................................................................................................19
14. Comm Ports ......................................................................................................................................................20
15. Modbus.............................................................................................................................................................21
16. Network Properties (PROTEUS K & X only).......................................................................................................22
17. DataCheck Settings ...........................................................................................................................................23
18. Interface Boards & Relays (PROTEUS K & X only) .............................................................................................23
19. Clear Logs..........................................................................................................................................................27
20. VLD – Leak System Settings ..............................................................................................................................28
21. VLD – Leak Tank Settings ..................................................................................................................................29
22. CITLD – Leak System Settings ...........................................................................................................................30
23. Email Account (PROTEUS K & X only) ...............................................................................................................31
24. Email Setup (PROTEUS K & X only) ...................................................................................................................32
25. Diagnostics........................................................................................................................................................33

OMNTEC Mfg., Inc., 2420 Pond Road, Ronkonkoma, NY 11779
Phone [phone] Fax [phone] www.OMNTEC.com
File Name: DOC00007 rev1.1.docx 3 of 37 Rev Date: 12-14-2021
Programming Manual
OEL8000III Series
1. Navigating to Setup
Home Screen: The SETUP MENU is
located under UTILITIES. (See Figure
1.1)
Utilities Screen: To enter setup press
SETUP MENU.(See Figure 1.2)
Enter Password: Enter the
manufacturer default password
“000000” when prompted by the unit
to proceed to the SETUP MENU. (See
Figure 1.3)
To change the password: Go to Section 5,
Miscellaneous Settings.
Figure 1.1
Figure 1.2
Figure 1.3

OMNTEC Mfg., Inc., 2420 Pond Road, Ronkonkoma, NY 11779
Phone [phone] Fax [phone] www.OMNTEC.com
File Name: DOC00007 rev1.1.docx 4 of 37 Rev Date: 12-14-2021
Programming Manual
OEL8000III Series
Setup Menu (Page 1):
Used to navigate to
corresponding system
setup options. (See
Figure 1.4)
Setup Menu (Page 2):
Used to navigate to
additional system setup
options. (See Figure 1.5)
a) Backup System Parameters: Backs up programming to
SD Card.
b) Restore System Parameters: Restores programming
from SD Card to PROTEUS ATG.
c) Print System Parameters: Prints entire system
programming. Each prompt will have a confirmation
message for “YES” or “NO.” (See Figure 1.5)
*SD Card features and printing for PROTEUS® K & X only*
Figure 1.4
Figure 1.5

OMNTEC Mfg., Inc., 2420 Pond Road, Ronkonkoma, NY 11779
Phone [phone] Fax [phone] www.OMNTEC.com
File Name: DOC00007 rev1.1.docx 5 of 37 Rev Date: 12-14-2021
Programming Manual
OEL8000III Series
2. System Units
Site Units of Measurement: The
default unit settings are displayed using
the imperial system, press the unit you
would like to change for the list of
options. You may also change the date
view between MM/DD/YYYY and YYYY-
MM-DD. (See Figure 2.1)
Set Units of Measurement: Select units
desired for volume, level, and
temperature. (See Figure 2.2)
Figure 2.1
Figure 2.2

OMNTEC Mfg., Inc., 2420 Pond Road, Ronkonkoma, NY 11779
Phone [phone] Fax [phone] www.OMNTEC.com
File Name: DOC00007 rev1.1.docx 6 of 37 Rev Date: 12-14-2021
Programming Manual
OEL8000III Series
3. Printer Settings (PROTEUS® K & X only)
Print Line Headers: Information
printed on the system status report
header.
Printer Settings: Selects on-board
printer or network printer. (See Figure
3.1)
a) Print Line Headers: The headers are used to program site specific information that
will print on the header of the system status report. Examples of the information to
be entered here would be site name, site address, site phone number, and
manager’s name.
b) Printer Settings: Selecting internal printer will use the PROTEUS® printer; selecting
TCP/IP printer will use printer linked to the same network as the PROTEUS® ATG.
Put the printer’s IP address and port number in the fields provided.
Figure 3.1

OMNTEC Mfg., Inc., 2420 Pond Road, Ronkonkoma, NY 11779
Phone [phone] Fax [phone] www.OMNTEC.com
File Name: DOC00007 rev1.1.docx 7 of 37 Rev Date: 12-14-2021
Programming Manual
OEL8000III Series
4. Shift Time Settings
Shift Time Settings: Setup for
generating daily shift reports.(See
Figure 4.1)
a) Number of Shifts: Number of shift reports to be generated daily.
b) Auto Print: Will enable or disable an automatic printout at each shift end time.
c) Shift End Times: End times for the number of shifts that were selected. If multiple
shifts are selected, the end time of the last shift will be the open time of the next
shift.
Figure 4.1

OMNTEC Mfg., Inc., 2420 Pond Road, Ronkonkoma, NY 11779
Phone [phone] Fax [phone] www.OMNTEC.com
File Name: DOC00007 rev1.1.docx 8 of 37 Rev Date: 12-14-2021
Programming Manual
OEL8000III Series
5. Misc. Settings
Miscellaneous Settings: Settings for
remote horns and alarm, as well as
auto print options for other settings.
SETUP MENU password can be
changed here as well. (See Figure 5.1)
a) Remote Horn Timeout: Amount of time the horn will sound before automatically
silencing.
b) Remote Horn Timeout Enable: Used to enable or disable the horn timeout.
c) Remote Alarm ACK Timeout: Amount of time before re-sounding the horn after it is
silenced (Remote horn settings for PROTEUS® K & X only).
d) Ullage %: The percent used to calculate ullage on printouts.
e) Setup Password: To change the password press the box and enter new password.
When finished press the save button.
f) Alarm Auto Printout: Used to enable or disable an automatic printout of Alarm
report.
g) Drop Auto Printout:Used to enable or disable the automatic printout of Drop report.
h) Shift Auto Printout:Used to enable or disable the automatic printout of Shift report.
i) VLD Auto-print:Used to enable or disable the automatic printout of VLD report.
j) Interstitial Auto Print:Used to enable or disable the automatic printout of an
interstitial sensor report (Printing for PROTEUS® K & X only).
Figure 5.1

OMNTEC Mfg., Inc., 2420 Pond Road, Ronkonkoma, NY 11779
Phone [phone] Fax [phone] www.OMNTEC.com
File Name: DOC00007 rev1.1.docx 9 of 37 Rev Date: 12-14-2021
Programming Manual
OEL8000III Series
Miscellaneous Settings (page 2):
Additional settings to adjust
Homepage and page change to
delivery in progress. (See Figure 5.2)
a) Delivery Page Change: Automatically wakes up the display to show a tank with
delivery in progress.
b) Backlight Timeout: Can be changed to dim the display between 1-255 minutes. Can
also be set to zero which leaves the display always ON (Inventory and Homepage
only).
c) Home Screen: Choose which page you would like to set as the Home Screen.
Choose from System Status, 4 Tank Inventory, Single Tank Inventory, Single Tank
Zoomed Inventory, or CLD (Containment Leak Detection) Mode. NOTE: you must
have a PROTEUS CLD system in order to operate the CLD Mode function.
d) Home Screen Tank #: If a single tank inventory page is chosen, this will select which
tank is shown.
e) Door Ajar Horn: New to Version 9, used for PROTEUS® ATG’s in an enclosure. The
system will chirp via the display horn if the enclosure door is left open and this
feature is on. Options are OFF, MCU-INPUT-2, 4IO-INPUT 1, 4IO-INPUT 2, 4IO-INPUT
3, 4IO-INPUT 4, (if the system has an XB-4IO board). The input is where a magnetic
switch (or equivalent) is connected to within the ATG unit.
f) Information: Will show and explain what each parameter does within miscellaneous
settings.
Figure 5.2

OMNTEC Mfg., Inc., 2420 Pond Road, Ronkonkoma, NY 11779
Phone [phone] Fax [phone] www.OMNTEC.com
File Name: DOC00007 rev1.1.docx 10 of 37 Rev Date: 12-14-2021
Programming Manual
OEL8000III Series
6. Tank Parameters
Setup-Tank Parameters: Various
parameters that are needed to obtain
proper and accurate functionality. (See
Figure 6.1)
a) Tank Number: Selects a tank for setup.
b) Product Type: Product type label (up to 17 characters).
c) Product Null: Amount subtracted from gauging probe product level measurement to
match actual product level measurement (Enter product height from stick reading).
d) Water Null: Amount subtracted from gauging probe water level measurement to match
actual water level measurement (Enter water height from stick reading).
e) Enable/Disable: Enable or disable the corresponding tank.
f) Tank Capacity: Total volume of tank (obtained from tank chart).
g) Tank Diameter: Height of tank (highest point on tank chart).
h) Probe Length: Overall probe length (last 3 digits from CAT # on the head of the probe).
i) Wire Speed: Factory defined wire speed (obtained from probe label).
j) Volume Correction:Brings you to the Volume Correction page where you can choose
from COEFFICIENT THERMAL EXPANSION, API GRAVITY, RELATIVE DENSITY or DENSITY.
(See next page for additional Volume Correction details.)
k) Probe Type: Shows how many temperature thermistors are in the probe. (Obtained
from CAT# on the head of the probe). **If using a “redhead” probe, enter 4.**
l) Volume Offset: Amount added to volume reading for further calibration.
Enter corresponding values on each box then press the “NEXT PAGE” icon to continue
programming alarm parameters on the same tank.
Figure 6.1