Metrologic IS4220 ScanGlove User manual

METROLOGIC INSTRUMENTS, INC.
IS4220 ScanGlove®
Laser Bar Code Scanner
Installation and User’s Guide
mlpn 2348 cover.qxd 9/21/2004 2:57 PM Page 1

ii
LOCATIONS
CORPORATE HEADQUARTERS
NORTH AMERICA EUROPEAN,MIDDLE EAST &AFRICAN
HEADQUARTERS
USA, NEW JERSEY GERMANY,MUNICH
Metrologic Instruments, Inc. Metrologic Instruments GmbH
Tel: 1-800-ID-METRO Fax: [phone] Tel: [phone] Fax: [phone]
Email: i[email protected] Email: i[email protected]
SOUTH AMERICA,BRAZIL SÃO PAULO GERMANY,MUNICH
Metrologic do Brasil Ltda. Metrologic Instruments GmbH
Tel: [phone] Fax: [phone] Tel: [phone] Fax: [phone]
Email: i[email protected] Email: i[email protected]
SOUTH AMERICA,OUTSIDE BRAZIL SÃO PAULO ITALY,BOLOGNA
Metrologic South America Metrologic Instruments Italia srl
Tel: [phone] Fax: [phone] Tel: [phone] Fax: [phone]
Email: i[email protected] Email: i[email protected]
ASIA,SINGAPORE FRANCE,PARIS
Metrologic Asia (Pte) Ltd Metrologic Eria France SA
Tel: [phone] Fax: [phone] Tel: [phone]
Email: [email protected]c.com Fax: [phone]
Email: i[email protected]
CHINA,SUZHOU
Metro Technologies Co., Ltd. SPAIN,MADRID
Tel: [phone] Fax: [phone] Metrologic Eria Ibérica, SL
Email: [email protected]ogic.com Tel: [phone] Fax: [phone]
Email: i[email protected]
Metro Sales Office
Tel: [phone] Fax: [phone] Metrologic Europe Repair Center (MERC)
Email: [email protected] Metrologic Eria Ibérica, SL
Tel: [phone] Fax: [phone]
JAPAN,TOKYO
Metrologic Japan Co., Ltd. UNITED KINGDOM,BASINGSTOKE
Tel: [phone] Fax: [phone] Metrologic Instruments UK Limited
Email: [email protected]ogic.com Tel: [phone]
Fax: [phone]
Email: i[email protected]etrologic.com
R
USSIA,MOSCOW
Metrologic Russia
Tel: [phone] Fax: [phone]
Email: i[email protected]
Copyright
© 2004 by Metrologic Instruments, Inc. All rights reserved. No part of this work may be reproduced,
transmitted, or stored in any form or by any means without prior written consent, except by reviewer, who
may quote brief passages in a review, or provided for in the Copyright Act of 1976.
Products and brand names mentioned in this document are trademarks of their respective companies.

iii
TABLE OF CONTENTS
Introduction .......................................................................................................... 1
Scanner and Accessories .................................................................................... 1
Scanner Installation.............................................................................................. 2
Scanner Configuration to the Host System .......................................................... 3
Parts of the Scanner ............................................................................................ 4
Visual Indicators................................................................................................... 5
Audible Indicators................................................................................................. 9
Labels................................................................................................................. 10
Maintenance....................................................................................................... 10
Infrared (IR) Object Sensor ................................................................................ 11
Scan Field .......................................................................................................... 12
Specifications ..................................................................................................... 13
Default Settings.................................................................................................. 14
Troubleshooting Guide....................................................................................... 19
Limited Warranty................................................................................................ 20
Notices ............................................................................................................... 21
Patents ............................................................................................................... 23
Index................................................................................................................... 24

1
INTRODUCTION
The IS4220 ScanGlove®is a fully automatic single-line laser barcode scanner.
It is designed to be used as a “hands-free” wearable scanner or a stationary
desktop scanner.
Every ScanGlove is equipped with ScanQuest®, a patented activation technology
that allows the scanner to read bar codes automatically as the operator presents
the bar code to the scanner. Additional features include; 52 scan lines a
second, short or long range activation and two universal glove sizes with left and
right-hand capabilities.
The IS4220 has built in decoding for applications that use a RS232, Keyboard
Wedge, Stand Alone Keyboard, Light Pen Emulation, or USB communication
interface. For additional information on other system interfaces call please call a
Metrologic Customer Service Representative at 1-800-ID-METRO.
SCANGLOVE MODEL NO. INTERFACE
IS4220-07 USB Keyboard
IS4220-08 USB POS
IS4220-14 RS232
IS4220-15 Light Pen Emulation
IS4220-17 PC Keyboard Wedge and Stand Alone Keyboard
IS4220-41 Full RS232 and Light Pen Emulation
SCANNER AND ACCESSORIES
PART NUMBER DESCRIPTION
IS4220 IS4220 Laser Scanner
00-02348 Installation and User’s Guide
00-02343 Programming Guide
00-02044 Programming Addendum (USB Models Only)
45-45455 Black Adjustable Glove
If any item is missing or to order additional items, contact the dealer, distributor or call
Metrologic’s Customer Service Department at 1-800-ID-METRO or 1-800-436-3876.

2
SCANNER INSTALLATION
1. Turn off power to the host system.
2. Connect the communication cable to the proper port on the host device.
3. Turn on power to the host system.
When the IS4220 first receives power, the red LED will flash, the
green LED will flash, and then the scanner will beep once.
Caution:
To maintain compliance with applicable standards, all circuits connected
to the scanner must meet the requirements for SELV (Safety Extra Low
Voltage) according to EN 60950.
To maintain compliance with standard CSA C22.2 No. 950/UL 1950 and
norm EN 60950, the power source should meet applicable performance
requirements for a limited power source.
To maintain compliance with federal regulations 21 CFR, Part 1040.10,
section (f)(6) the scanner must be plugged into an electrical outlet with a
switch accessible to the user or be powered by a host system containing
a switch that will disable power to the scanner.

3
SCANNER CONFIGURATION TO THE HOST SYSTEM
The IS4220 is shipped from the factory pre-programmed to a set of default
parameters. It may be necessary to change the default parameters to match the
host system’s requirements or to enable additional scanner functions. For a list
of possible parameter settings, refer to the Default Settings section of this guide.
Important notes for the -07 and -08, IS4220 USB Interfaces.
The IS4220-07 and the IS4220-08 are pre-programmed for USB
Emulation before leaving the factory. If the recall defaults bar code is
scanned the unit must be re-programmed for USB Emulation before
enabling or disabling any additional features documented in the
programming guide (MLPN 00-02343).
To re-program the unit for USB Keyboard Emulation or USB POS
Emulation refer to the IS4220 USB Addendum (MLPN 00-02044)
for the IS4220 Programming Guide.
To modify the scanner’s default parameters follow the steps below using the bar
codes located in the programming guide (MLPN 00-02343).
1. Scan the
ENTER PROGRAM MODE bar code to enter programming mode. The
scanner will beep three times.
2. Scan the bar code(s) for the desired parameter(s). The scanner will beep
once.
3. Scan the
EXIT PROGRAM MODE bar code to exit and save the new parameter
settings. The scanner will beep three times.
If during programming there is a need to return the scanner to the
original factory settings, scan the recall defaults bar code in the
programming guide. All settings selected during that session or any
previous sessions are discarded when you scan the recall defaults
code.
Please read the warning above for the IS4220-07 and -08 models
before using the recall defaults bar code.

4
PARTS OF THE SCANNER
Figure 1. Scanner Parts
Item
No. Description

Green LED
When a bar code is read successfully the green LED will flash.

Red LED
When the red LED is illuminated, the laser is on.

Red Output Window (Laser Aperture)

Infrared Sensor (IR)
If a specified time has elapsed without any scanning, the unit will
enter a “standby” mode. To reactivate the unit, place an object in
front of the IR sensor. The red LED will turn on when the scanner
is ready to scan.

Communication/Power Cable
This cable’s termination is application dependent.

5
VISUAL INDICATORS
There is a red and a green LED located on the top of the scanner. When the
scanner is on, the flashing or constant illumination of the LEDs indicates the
status of the current scan and the scanner.
No Red LED Illumination of the LEDs will not occur if the scanner has
remained dormant for a specified time and the scanner is
not receiving power from the host. To reactivate the unit,
direct the output window up then down toward the object.
Red Flash;
Green Flash;
Steady Red
When the scanner first receives power, the red LED will
flash, followed by the green LED, and then the unit will
beep once. The red LED will stay on after it flashes once.
Steady Red When the laser is on, the red LED will be on. This occurs
when an object is detected in the scan field. If the scanner
cannot detect a bar code within approximately 2.5
seconds, the unit will go into a standby mode and the red
LED will shut off indicating that the laser is no longer on.
Steady Red
LED; Green
Flash
When the scanner successfully reads a bar code, the
green LED will flash and the unit will beep once. If the
green LED does not flash or the scanner does not beep,
then the bar code was not successfully read.
Repetitive Red
LED Flashing
When the red LED flashes several times while it rests
upon a stationary surface, then an object is within the scan
field and is activating the IR sensor repetitively.
To eliminate this disturbance, direct the scan window
toward a different location.
Steady Green
LED
After a successful scan, the scanner transmits the data to
the host device. When the host is not ready to receive the
information, the green LED will remain on until data can
transmit.

6
SIGNAUX OPTIQUES
Sur la partie supérieure du scanner se trouvent une diode LED rouge et une
diode LED verte. Quand le scanner est sous tension, les diodes rouge et verte
clignotantes ou allumées vous informent sur l'état de palpage et de scanner.
Ni la diode
rouge, ni la
diode verte
n'est allumée
Il existe deux raisons possibles pour que les diodes ne
s'allu-ment pas. Si le scanner ne reçoit pas d'énergie de
l'ordinateur PC, les diodes ne s'allument pas. Quand le
scanner reçoit de l'énergie et ne s'allume cependant pas,
le scanner est resté pendant une certaine période sans
être utilisé et le laser et lemoteur sont désactivés. Pour
réactiver l'unité, déplacer un objet devant le palpeur
infrarouge ou prendre le scanner et diriger la fenêtre de
palpage vers le bas.
Diode rouge
clignotante;
diode verte
clignotante;
diode rouge
reste allumée
Quand le scanner reçoit pour la première fois de l'énergie,
la diode rouge se met d'abord à clignoter, puis la diode
verte. Ensuite, le scanner émet un bip sonore unique. Une
fois cette séquence de démarrage effectuée, la diode
rouge reste allumée pendant un certain temps indiquant
que le laser est en service. Quand le scanner ne détecte
aucun objet, la diode rouge et le laser s'éteignent.
Diode rouge
reste allumée
Quand le laser est activé, la diode rouge s'allume
également. C'est par exemple le cas quand un objet se
trouve devant la fenêtre de palpage. Si, en l'espace de 2,
5 secondes, aucun code barres n'est détecté, la diode
rouge s'éteint, ce qui signifie que le laser est désactivé.
Diode rouge
reste allumée;
diode verte
clignotante
Après lecture avec succès d'un code barres par le
scanner, la diode verte se met à clignoter, suivie d'un bip
sonore unique. Si la diode verte ne clignote pas ou quand
aucun bip sonore n'est émis, cela signifie que le code
barres n'a pas pu être lu avec succès.
Clignotement
répété de la
diode rouge
Quand la diode rouge clignote plusieurs fois pendant que
l'appareil repose sur une surface non déplacée, un objet
activant le palpeur infrarouge se trouve devant la fenêtre
de palpage. Ceci peut se produire même quand le
scanner se trouve sur une table ou un reposoir. Pour
éliminer ce défaut, positionner le scanner de façon
différente.
Diode verte
reste allumée
Une fois le palpage effectué avec succès, le scanner
transmetles donnéesà l'ordinateur PC. Si ce dernier n'est
pas prêt à recevoir les données, la diode verte du scanner
s'allume jusqu'à ce que les donnés puissent être
transmises.

7
OPTISCHE ANZEIGEN
Auf der Oberseite des Scanners befinden sich eine rote und eine grüne
Leuchtdiodenanzeige. Ist der Scanner eingeschaltet, so geben Ihnen die
blinkenden oder feststehenden Leuchtdiodenanzeigen Aufschluß über den
Abtast und Scannerstatus.
Weder rote
oder noch
grüne
Leuchtanzeige
Es gibt zwei mögliche Gründe, weshalb die Leuchtdiodenan
zeigen nicht aufleuchten. Bekommt der Scanner keine Energie
vom PC, leuchten die Leuchtdiodenanzeigen nicht auf. Wenn
der Scanner jedoch Energie bekommt und die
Leuchtdiodenanzeigen dennoch nicht aufleuchten, so ist der
Scanner für einen bestimmten Zeitraum untätig geblieben, und
Laser und Motor sind abgeschaltet. Zur Reaktivierung der Einheit
sollten Sie ein Objekt vor dem Infrarot Sensor hin und
herbewegen oder den Scanner aufnehmen und das
Abtastfenster nach unten richten.
Rote
Blinkanzeige;
Grüne
Blinkanzeige;
feststehende
grüne
Leuchtanzeige
Wenn dem Scanner erstmalig Energie zugeführt wird, blinkt
zunächst die rote Leuchtdiodenanzeige auf, gefolgt von der
grünen Leuchtdiodenanzeige,und anschließend sendet der
Scanner ein einmaliges Piep-Signal aus. Nach Ausführung
dieser Startsequenz leuchtet die rote Leuchtdiodenanzeige für
einen bestimmten Zeitraum auf und zeigt an, daß der Laser
eingeschaltet ist. Wird dem Scanner kein Objekt präsentiert, so
schalten sich die rote Leuchtdiode und der Laser ab.
Feststehende
rote
Leuchtanzeige
Wenn der Laser eingeschaltet ist, leuchtet auch die rote Leucht-
diodenanzeige auf. Dies ist dann der Fall, wenn sich ein Objekt
im Abtastfeld befindet. Wird innerhalb von ca. 2,5 Sekunden
kein Barcode erfaßt, so erlischt die rote Leuchtdiodenanzeige,
was bedeutet, daß der Laser nicht mehr eingeschaltet ist.
Feststehende
rote
Leuchtanzeige;
grüne
Blinkanzeige
Nach erfolgreichem Lesen eines Barcodes durch den Scanner
blinkt die grüneLeuchtdiodenanzeige auf, gefolgt von einem
einmaligen Piep-Signal. Falls die grüne Leuchtdiodenanzeige
nicht aufblinkt oder der Scanner kein einmaliges Piep-Signal
aussendet, bedeutet dies, daß der Barcode nicht erfolgreich
gelesen werden konnte.
Wiederholte
rote
Blinkanzeigen
Blinkt die rote Leuchtdiodenanzeige mehrmals auf, während das
Gerät auf einer nichtbewegten Fläche liegt, so befindet sich ein
Objekt inner halb des Abtastfeldes,das den Infrarot-Sensor
aktiviert. Dies kann selbst dann vorkommen, wenn der Scanner
auf dem Ladentisch oder dem Ablagegestell liegt. Um diese
Störung zu beseitigen, sollten Sie den Scanner anders
positionieren.
Feststehende
grüne
Leuchtanzeige
Nach erfolgreichem Abtasten überträgt der Scanner die Daten an
den PC. Ist der PC nicht zur Annahme der Daten bereit, so
leuchtet die grüne Leuchtdiodenanzeige des Scanners solange
auf, bis die Daten übertragen werden können.

8
SEGNALI OTTICI
Sulla parte superiore dello scanner si trovano due diodi luminosi: uno rosso e
uno verde. Quando lo scanner è inserito, i diodi luminosi, che possono o essere
accesi in continuazione o lampeggiare, Vi informano sullo stato della scansione
e dell’apparecchio.
Né il diodo
luminoso rosso
né quello verde
sono accesi
Vi sono due possibili cause se i diodi luminosi non sono
accesi. Se lo scanner non viene alimentato dal PC i diodi
luminosi non sono accesi. Se invece lo scanner è
alimentato e ciònonostante Idiodi luminosi non sono accesi,
lo scanner è rimasto disattivato per un determinato periodo
e laser e motore sono spenti. Per riattivare l’unità
dovreste muovere un oggetto davanti al sensore a
infrarossi oppure prendere lo scanner e rivolgere il
finestrino di scansione verso il basso.
Il diodo luminoso
rosso lampeggia;
il diodo luminoso
verde lampeggia;
il diodo luminoso
verde è acceso
Quando lo scanner viene alimentato per la prima volta,
lampeggia dapprima il diodo luminoso rosso e quindi
quello verde. Poi lo scanner emette un unico segnale
beep Dopo l’esecuzione di questa sequenza di avvio il
diodo luminoso rosso si accende per un determinato
periodo ed indica che il laser è inserito. Se allo scanner
non viene presentato nessun o ggetto, il diodo luminoso
rosso e il laser si spengono.
Il diodo
luminoso rosso
è acceso
Quando il laser è attivato, è acceso anche il diodo
luminoso rosso. Questo si ha quando un oggetto si trova
nella zona di scansione. Se entro ca. 2, 5 secondi non
viene registrato nessun codice a barre, il diodo luminoso
rosso si spegne; ciò significa che il laser non è più attivato.
Il diodo luminoso
rosso è acceso; il
diodo luminoso
verde lampeggia
Dopo la lettura riuscita di un codice a barre da parte dello scanner
il diodo luminoso verde lampeggia e quindi viene emesso un unico
segnale beep. Se il diodo luminoso verde non lampeggia oppure
lo scanner non emette un segnale beep, ciò significa che la lettura
del codice a barre non è riuscita.
Il diodo luminoso
verde è acceso
Dopo la scansione riuscita lo scanner trasmette i dati al
PC. Se il PC non è pronto per accettare i dati, il diodo
luminoso verde dello scanner è acceso fino a che i dati
possono essere trasmessi.
Il diodo
luminoso rosso
lampeggia
ripetutamente
Se il diodo luminoso rosso lampeggia ripetutamente
mentre l’app-arecchio si trova su una superficie che non si
muove, vi è un oggetto all’ interno della zona di scansione
che attiva il sensore a infrarossi. Ciò può essere
addirittura il caso quando lo scanner si trova sul banco
oppure nel suo supporto. Per eliminare questa anomalia
basta cambiare la posizione dello scanner.

9
AUDIBLE INDICATORS
The scanner provides sounds to signal certain conditions. To change the
volume (four settings are available) or turn the beeper off, refer to Beeper Tones
in the Programming Guide.
One Beep When the scanner first receives power, the red LED will
flash, followed by the green LED, and then the scanner
will beep once. After the scanner performs this start-up
sequence, the scanner is ready to scan.
When the scanner successfully reads a bar code, the
green light will flash and the unit will beep once. If the
green LED does not flash or the scanner does not beep,
then the bar code read is not successful.
Razzberry Tone If, upon power up, the scanner emits a razzberry tone the
scanner has failed diagnostics.
The scanner can be programmed to emit a
razzberry tone when the timeout occurs during
communication between the host and scanner.
Refer to Audible Indicators for Communication
Timeouts the Programming Guide.
Three Beeps When entering program mode, the green LED will flash
three times while the scanner simultaneously beeps
three times. When exiting program mode, the same
visual and audible indications will occur. After this
sequence is completed, the red LED will turn off.
The scanner can be programmed to emit three
beeps when the timeout occurs during
communication between the host and scanner.
Refer to Audible Indicators for Communication
Timeouts the Programming Guide.

10
LABELS
Each IS4220 has a serial number label and a laser class label on the bottom of
the unit. These labels provide important information like; date and location of
manufacture, model number, serial number, caution statements and laser class.
There is also text molded into the top of the case near the window that says,
“AVOID EXPOSURE - laser light emitted from this aperture”. The following
Figure shows examples of these labels*.
Figure 2. Caution and Serial Number Labels*
* Labels not shown to scale.
MAINTENANCE
Smudges and dirt can interfere with the proper scanning of a bar code.
Therefore, the output window will need occasional cleaning.
1. Spray glass cleaner onto lint free, non-abrasive cleaning cloth.
2. Gently wipe the output window.

11
INFRARED (IR) OBJECT SENSOR
An infrared (IR) device located behind the window initiates the scanning process.
The IR sensor is active as long as power is applied to the unit. When the IR
sensor detects an object, the green LED will flash. When the laser decodes a
bar code, the scanner transmits the data to the host system and emits a beep to
show that decoding is complete. The IR sensor range can be programmed for
two ranges.
Short Range Activation
The IR signal initiates the scan process if it senses an object anywhere from the
face of the window out to approximately 4" to 7".
Long Range Activation
The IR signal initiates the scan process if it senses an object anywhere from the
face of the window out to approximately 9" to 13".
If the object is removed from the field during the scanning process, the laser
turns off and the scanner re-enters "standby" mode. However, if the object stays
in the field, the laser remains on for up to 2.5 seconds trying to detect another
bar code. If the scanner does not detect a bar code, the scanner re-enters
"standby" mode. To reactivate the scanning sequence, remove the object and
present another.
If the same symbol stays in the field after a successful scan, the laser stays on
for approximately 7.5 seconds and then turns off. This prevents unintentional
reads of the same bar code. To read the same symbol more than once, remove
the object from the scan field for approximately 1 second and then present the
symbol again.

12
Scan Field
The depth of field for the scanner is 12.7 mm to 203 mm (.5" to 8") from the face of
the output window for .33 (13 mil) Bar Codes.
Figure 3. Scan Field for .33 (13 mil) Bar Codes
Specifications subject to change without notice.

13
SPECIFICATIONS
IS4220 SPECIFICATIONS
OPERATIONAL
Light Source: 650 nm VLD
Depth of Field: 12.7 mm to 203 mm (.5" to 8") for .33 (13 mil) bar code
Width of Scan Field: 28.6 mm (1.125”) @ face; 102 mm (4”) @ 76.2 mm (3”)
Scan Speed: 52 scans lines per second
Scan Pattern: Single scan line
Min Bar Width: 0.173 mm (6.8 mil)
Decode Capability: Autodiscriminates all standard bar codes; for other
symbologies call a Metrologic representative
System Interfaces: RS232, Light Pen Emulation, PC Keyboard Wedge, Stand
Alone Keyboard, USB (low speed)
Print Contrast: 35% minimum reflectance difference
Number of
Characters Read:
up to 80 data characters (Maximum number will vary based
on symbology and density)
Roll, Pitch, Yaw: 42°, 68°, 52°
Beeper Operation: 3 tones or no beep
Indicators (LED): red = laser on, ready to scan green = good read, decoding
MECHANICAL
Length x Width x Height: 70 mm x 49 mm x 24 mm (2.75" x 1.94” x 0.94”)
Weight: 105 grams (3.7 oz.)
Cable Termination: Application Dependent
ELECTRICAL
Input Voltage: 5VDC ± 0.25V
Power: 0.75 W
Operating Current: 135 mA
DC Transformers: Class 2; 5VDC @ 300 mA
Laser Class 2: EN 60825-1:1993+A1:1997+A2:2001
EN 60825-1:1994+A11:1996+A2:2001
EMC: FCC, ICES-003 & EN 55022 Class A
ENVIRONMENTAL
Operating Temperature: -20°C to 50°C (-4°F to 122°F)
Storage temperature: -40°C to 70°C (-40°F to 158°F)
Humidity: 5% to 95% relative humidity, non-condensing
Light Levels: Up to 4842 Lux (450 footcandles)
Shock: Designed to withstand 1.5 m (5’) drops
Contaminants: Sealed to resist airborne particulate contaminants
Ventilation: None required
Specifications subject to change without notice.

14
DEFAULT SETTINGS
Many functions of the scanner can be "programmed", that is enabled or
disabled. The scanner is shipped from the factory programmed to a set of
default conditions. All factory default parameters have an asterisk ( * ) in the
default column of the charts on the following pages . If an asterisk is not in the
default column then the setting is off or disabled by default. Every interface does
not support every parameter. If the interface supports a parameter listed in the
charts on the following pages, a check mark () will appear.
PARAMETER DEFAULT RS232 LIGHT
PEN
KEYBOARD
WEDGE USB
Enter Program Mode After Any Scan * 
Enter Program Mode Only on
First Scan 
Short Range Activation 
Long Range Activation * 
Normal Scan * 
Pulsing Scan 
Custom Scan 
Short Same Symbol Rescan 
Long Same Symbol Rescan * 
Alternate Beeper Tone 1 
Alternate Beeper Tone 2 * 
Alternate Beeper Tone 3 
No Beeper Tone 
Two Second Timeout 

No Two Second Timeout * 

Razzberry Tone on Timeout 

No Tone on Timeout * 

Three Beeps on Timeout 

Beep Before Transmit * 
Beep After Transmit 
Baud Rate 9600 

Parity Space 

8 Data Bits 

7 Data Bits * 

RTS/CTS 
Character RTS/CTS * 
Message RTS/CTS 

15
DEFAULT SETTINGS
PARAMETER DEFAULT RS232 LIGHT
PEN
KEYBOARD
WEDGE USB
ACK/NAK 
XON/XOFF * 
No Intercharacter Delay 
1 Millisecond Intercharacter Delay 
5 Millisecond Intercharacter Delay 

10 Millisecond Intercharacter Delay 
25 Millisecond Intercharacter Delay 

100 Millisecond Intercharacter Delay 
DTR Input 
DTR Scan Disable 
“DE” Disable Command 
LRC Calc+ Transmit RS232 
Start LRC on first RS232 Byte 
Start LRC on Second RS232 Byte * 
Carriage Return * 
Line Feed * 
STX Prefix 
ETX Suffix 
Tab Prefix 
Tab Suffix 
Prefix ID for UPC/EAN 
Suffix ID for UPC/EAN 
Bars High * 
Spaces High 
Transmit as Scanned * 
Transmit as Code 39 
Poll Light Pen 5 Volts 
No Poll Light Pen * 
Reverse Polarity Idle for Light Pen 
UPC * 
EAN * 
Full ASCII code 39    
Code 39 * 
Codabar 
Code 128 * 
Code 93 * 
Interleaved 2 of 5 (ITF) * 
Code 11    

16
DEFAULT SETTINGS
PARAMETER DEFAULT RS232 LIGHT
PEN
KEYBOARD
WEDGE USB
Hong Kong Matrix 2 of 5    
Airline 2 of 5    
Minimum 1 Character Code Length 
Minimum 3 Character Code Length * 
Minimum 6 Character Code Length 
Set Minimum Character Length    
Set Character Lock Length    
Transmit UPC-A Number Sys * 
UPC-A Check Digit Transmit * 
Convert UPC-A to EAN-13 
Expand UPC-E 
UPC-E Check Digit Transmit 
UPC-E Leading 0 Transmit 
EAN-8 Check Digit Transmit * 
EAN-13 Check Digit Transmit 
Convert EAN-8 to EAN-13 
“$” Prefix ID for UPC/EAN 
2 Digit Supps (Scan) 
5 Digit Supps (Scan) 
Bookland (Scan)  
Supplement Required  
Bookland to ISNB    
Transmit ISNB CD    
Mod 43 Check Digit Code 39    
Transmit Mod 43 Check Digit Code 39 *    
Transmit Start/Stop Code 39    
CLSI Editing (Enable) 
ITF Check Digit 
Transmit MOD 10 ITF Check Digit 
I 2 of 5 Symbol Lengths Variable 
ISBN Reformatting 

Coupon Code 128 