Metsys ML360 User manual
ML360
/
ML360G
M
A
NU
A
L
I N T R O D U C T I O N
I 01
High quality laser beams ensure the visibility. Green LD withstands the hot/ cold
environment at any job sites.
The 2600 mah Lithium-ion battery system provides satisfactory battery
performance, savings on battery costs.
Robust design, Over-mold housing and alloy topping ensures that the lasers can
perform well even after minor accidents.
The included magnetic bracket, and clamp allows the laser to be used for
various applications, such as ceiling and drywall installation.
The LS1 Receiver and fine adjustment base are optional accessories to the
standard kit. The LS1 receiver can be added when doing outdoor short range
applications, as for the Fine adjustment base is ideal for precise pinpoint indoor
applications.
The laser unit is classified as a Class
Ⅱ
laser.
Be careful not to expose your eyes to the laser beam while the instrument is
operating.
Direct exposure to the laser beam for a long time maybe hazardous to your eyes.
Do not try to dismantle the instrument. Only allow this to be done by your local
Metsys service Centre.
The ML360 series, generates continuous 360 degree planes of laser light. A
horizontal plane is ideal for ceiling and height-transfer applications, whilst two
vertical planes that are 90 degrees apart provide all the reference needed for all
indoor tasks.
O P E R
A
T I O N
02 I
When the unit is not in use, the pendulum should always be in the Off position
Locking the pendulum allows the Laser unit to better withstand vibration and
trauma incurred during transportation or in the case the unit is dropped.
To use the laser under leveling mode, Users should push the main switch button to
the Unlock position and the horizontal plane will be activated. Press the laser
selection on the control panel, to active the other two vertical beams. Each laser
plane can be individually selected. To use with a laser detector, users need to press
the pulse button to activate this function.
T R O U B L E
S H O O T I N G
SOLUTIONS
Check
the
batteries
,
they
may
be
in
the
wrong
way
or
need
replacing
,
check
the
battery
compartment
for
signs
of
damage
,
ensure
they
are
clean
and
not
bent
.
Check
the
batteries
,
check
the
compartment
for
signs
of
damage
and
make
sure
they
are
clean
and
not
bent
.
Instrument
may
be
outside
its
self
-
leveling
range
,
adjust
the
instrument
or
tripod
so
it
is
level
,
the
instrument
may
have
low
power
,
instrument
may
have
impact
damage
.
ERROR
Laser
doesn
'
t
turn
on
Laser
doesn
'
t
remain
on
for
long
use
periods
of
use
.
Laser
doesn
'
t
self
-
level
P R O D U C T
S P E C I C
A
T I O N S
I 03
FEATURE
Overall
Accuracy
Levelling
Range
Working
Range
without
sensor
(
LS1
)
Working
Range
with
Sensor
(
LS1
)
Tripod
Thread
Laser
Type
Wavelength
Operating
Temperature
Storage
Temperature
Dimensions
(
mm
)
Continuous
working
hours
Protection
Class
Net
Weight
Batteries
Out
of
level
indicator
Out
of
battery
indicator
SPEC'S
±
3mm
/
10m
±
3
.
5
°
15m
R
/
25m
G
Up
to
50m
1
/
4
" &
5
/
8
"
Class
II
660nm
R
/
515
G
-
10
℃
to
45
℃
-
20
℃
to
60
℃
..............................
10
hrs
.
R
/
7
hrs
.
G
IP
54
1
.
1
KG
2600
mAh
,
7
.
4V
Laser
beam
flashing
Decal
indicator
flashing
P R O D U C T
I N C L U S I O N S
1x ML360/360G Laser tool
1x Magnetic ceiling bracket
Clamp for drywall application
1x Magnetic laser Target
Visibility enhancement glasses
Injection carry case
1x Charger
LS1 detector
Fine adjustment base
1.5m Tripod
Optional Extras
04 I
W
A
R R
A
N T Y
All
Metsys
line
lasers
have
the
ability
for
an
Extended
warranty
(
1
year
),
Standard
warranty
on
these
lasers
is
:
1
year
Total
with
Extended
warranty
claimed
is
2
years
.
FUNCTION
Select
this
symbol
/
Button
to
activate
the
Pulse
Mode
for
the
ML360
Series
to
use
the
LS1
SYMBOL
R E C E I V E R
(
L S 1
)
O P E R
A
T I O N
Switch the LS1 (detector / receiver) on by pressing the power button, the
speaker will beep indicating the instrument is operating.
Move the receiver / detector into the path of the laser beam.
Hold the Detector upright for horizontal beams , rotate the receiver / detector 90
degrees for vertical beams.
1
.
2
.
3
.
Note:
The
led
direction
indicators
will
indicate
the
position
of
the
laser
beam
,
the
center
LED
will
indicate
alignment
with
the
beam
.
I 05
C O N T A C T U S
F O L L O W U S
A D D R E S S 14 STEPHENSON ROAD,
BAYSWATER NORTH,
VICTORIA 3153
03 9720 6222
P R O D U C T D E S I G N E R
Justin Davis
P U R C H A S E O N L I N E
www.lightwavetechnology.com.au
E X T E N D E D W A R R A N T Y S U B M I S S I O N S
http://www.metsys.com.au/warranty/4594309423
P H O N E :
M E T S Y S
_
L
A
S E R S
@
M E T S Y S L
A
S E R S
support@metsys.com.au
E M A I L :
This manual suits for next models
1
Other Metsys Measuring Instrument manuals
