MFG FUN WORLD-EP User manual

FUN WORLD-EP
FUN WORLD-EP
INSTRUCTION MANUAL
39.5 in / 1000 mm
25.4 oz / 720 g
421 sq in / 27.2 sq dm
39.5 in / 1000 mm
Wing Span
Wing Area
Flying Weight
Fuselage Length
Specifications
A
E
D
R
-
Y
T -
T
S
O
O
-
F
M
L
L
Y
A
Requires: 4-channel radio w/ 4 micro servos,
Outrunner Motor KM0283010
w/ Propeller Adaptor HW2340100
20A brushless ESC, 3 cells 11.1V
2100 mAh Li - Po battery & charger.
*Specifications are subject to change without notice.*
Warning! This model is not a toy.
It is designed for maximum performance. Please seek advice if one is not familiar with this kind
of electric powered precision model. Operating this model without prior preparation may cause
injuries. Remember, safety is the most important thing. Always keep this instruction manual at
hand for quick reference.
FACTORY PRE-FABRICATED
ALMOST-READY-TO-FLY(ARF) SERIES
MADE IN CHINA
The World Models
Manufacturing Co., Ltd.
www.theworldmodels.com
E228SXMPO25581107

FUN WORLD-EP
FUN WORLD-EP
P.1
Apply thread locker
Apply epoxy glue.
Pierce the shaded portion
covering film.
Apply instant glue
(C.A.glue, super glue.)
Ensure smooth non-bindin g
movement while assembling.
Do not overlook this symbol !
P. 3 -10
INDEX
BEFORE YOU BEGIN
PARTS LIST
ASSEMBLY
SAFETY PRECAUTIONS
P. 1
P. 2
P.10
BEFORE YOU BEGIN
Check all parts. If you find any defective or missing parts contact your local dealer. Please DRY FIT
and check for defects for all parts that will require CA or Epoxy for final assembly. Any parts you
find to be defective after the gluing process may be difficult to remove for warranty replacement. The
manufacturer will replace any defective parts, but will not extend to the parts that are good before
gluing to defective parts during assembly. Warranty will not cover any parts modified by customer.
Read through the manual before you begin, so you will have an overall idea of what to do.
Symbols used throughout this instruction manual comprise of the following : -
1
2
3
Assemble left and right
sides the same way.
Peel off shaded portion
covering film.
Drill holes with the specified
diameter (here: 3mm) .
Pay close attention here!
Cut off shaded portion.
Must be purchase d separately !
Warning!
3mm
E228SXMPO25581107

Parts List
COVERING:--
LIGHTEX SGX000 TRANSPARENT
LIGHTEX SGX030 TRANSPARENT YELLOW
LIGHTEX SGX100 WHITE
LIGHTEX SGX050 TRANSPARENT BLUE
LIGHTEX SGX241 TURQUOISE
LIGHTEX SGX360 VIOLET
LIGHTEX SGX330 CADMIUM YELLOW
LIGHTEX SGX313 PINK
LIGHTEX SGX201 BLACK
LIGHTEX SGX251 SKY BLUE
LIGHTEX SGX250 BLUE
LIGHTEX SGX311 FERRARI RED
LIGHTEX SGX310 RED
1. MAIN WING -- 1 pair
2. PUSHROD Ø1.4x90mm w/ Threads (For Aileron) -- 2 pcs
STRAPER PL4112106 -- 2 pcs
CLEVIS PL4112105 -- 2 pcs
FUEL TUBE d2xD4x4mm -- 4 pcs
HORN PL4113102 -- 2 sets
SCREW PB2x10mm -- 4 pcs
3. FUSELAGE -- 1 pc.
STABILIZER & ELEVATOR -- 1 set
4. VERTICAL FIN & RUDDER -- 1 set
5. TAIL LANDING GEAR PL3410030 -- 1 set
TAIL WHEEL Ø23mm -- 1 pc.
ALUMINUM PLATE 0.3mm -- 1pc.
SCREW PA2x8mm -- 2 pcs
SCREW PM2x8mm -- 1 pc.
M2 NUT -- 1 pc.
6. MAIN LANDING GEAR -- 1 set
MAIN WHEEL Ø40mm PL3116040 -- 2 sets
COLLAR 2.6mm w/ set screw -- 2 pcs
LANDING WIRE STRAPS PL4114030 -- 3 pcs
SCREW PA2.3x10mm -- 6 pcs
7. PUSHROD Ø1.4x443mm w/ Threads (For Elevator) -- 2 pcs
CLEVIS PL4112105 -- 2 pcs
HORN PL4113102 -- 2 sets
SCREW PB2x10mm -- 4 pcs
FUEL TUBE d2xD4x4mm -- 2 pcs
8. PUSHROD Ø1.4x497mm w/ Threads ( For Rudder) -- 1 pc.
CLEVIS PL4112105 -- 1 pc.
FUEL TUBE d2xD4x4mm -- 1 pc.
HORN PL4113102 -- 1 set
SCREW PB2x10mm -- 2 pcs
9. FOLDING PROPELLER SET(10x6) PL6314020 -- 1 set
SPINNER Ø36mm PL21R3610/PL21SB360 -- 1 set
COWLING -- 1 pc.
SCREW PWA2x8mm -- 4 pcs
SOCKET HEAD SCREW M3x6mm -- 4 pcs
WASHER d3xD7mm -- 4 pcs
10. PUSHROD Ø1.4x40mm (For Elevator) -- 1 pc.
PUSHROD CONNECTOR PL4410020 -- 1 set
FUEL TUBE d2xD4x4mm -- 2 pcs
STRAPER PL4112106 -- 2 pcs
SPONGE 10x50x150mm -- 2 pcs
BATTERY TIE 200mm -- 1 pc.
DOUBLE-SIDED TAPE 30x35mm -- 1 pc.
SCREW PM2x10mm -- 2 pcs
WASHER d2xD5mm -- 2 pcs
M2 NYLON INSERT LOCK NUT -- 2 pcs
MOUNTING PLATE PL4114015 -- 2 pcs
PLYWOOD 2x56x95mm -- 1 pc.
BALSA 1.5x56x205mm -- 1 pc.
11. CANOPY -- 1 pc.
SCREW PWA2x8mm -- 4 pcs
12. EYE SCREW PA2.5x10x23mm AM1180105 -- 2 pcs
WING TUBE Ø9.6x240mm -- 1 pc.
RUBBER BAND D30x1mm -- 2 pcs
13. DECALS: E288SDEC -- 1 set
P.2
E228SXMPO25581107

P.3
Stabilizer & Elevator
3
Aileron Servo
2
1Main Wing
Apply instant type CA
glue to both sides of
each hinge.
Bottom View
Aileron Servo lead
Bottom View
4
PB2x10mm Screw
Ø1mm pilot holes for World Models control horn are pre-drilled.
Please look for pin-hole marks at under side of control surfaces.
Temporary install the main wing, adjust
leveling of the stabilizer to make it as
parallel to the main wing as possible.
(Stabilizer)
(Main Wing)
A A’
A=A’
B=B
B
B
Apply instant type CA glue to both
sides of each hinge.
TWM PL8210010
CLEVIS WRENCH
E228SXMPO25581107
Horn
Straper
PB2x10mm
Clevis
Fuel Tube
Ø4x4mm
Pushrod
Ø1.4x90mm

P.4
Tail Landing Gear
5
4Vertical Fin & Rudder
Completed
Apply instant type CA glue to both
sides of each hinge.
1.5mm
2mm
Bottom View
Plastic Collar
Wheel Ø23mm
PA2X8mm
M2 Nut
PM2X8mm
C=C
CC
2
PB2x8mm Screw
E228SXMPO25581107

P.5
Rudder Pushrod
8
Elevator Pushrod
7
6Main Landing Gear
M3x3mm Set Screw
2.6mm Collar
PA2 .3x10mm Screw
6
2.6mm Collar
2
Front
Bottom View
4
PB2x10mm Screw
Bottom View
Ø1mm pilot holes for World Models horn are pre-drilled.
Please look for pin-hole marks at under side of control surfaces.
≈165mm
≈18mm
PB2x10mm
Clevis
Horn
2
PB2x10mm Screw
Bottom View
Fuel Tube
Ø4x4mm
PA2 .3x10mm
Landing wire straps
Pushrod
Ø1.4x497mm
≈82mm
≈11mm
Ø1mm pilot holes for World Models horn are pre-drilled.
Please look for pin-hole marks at under side of control surfaces.
1.5mm
TWM PL8210010
CLEVIS WRENCH
TWM PL8210010
CLEVIS WRENCH
E228SXMPO25581107
PB2x10mm
Clevis
Horn
Fuel Tube
Ø4x4mm
Pushrod
Ø1.4x443mm

P.6
9Outrunner Motor & Cowling
5
4
Don't over-tighten the PM2 screws, let the
propeller blades align themselves when spinning.
PM2 x 12mm
PM2 x 12mm
PA2.6 x 8mm
Spinner
Ø36mm
PWA2 x 8mm
1.5mm
6
PWA2x8mm Screw
4
4
PM2x12mm Screw
2
d3xD7mm Washer
4
M3x6mm Socket Head Screw
Outrunner Motor 28/ 30
KM0283010
Propeller Adaptor
(d3xD5) HW2340100
Optional Parts
TWM
KP0011310
SolderSolder
TWM HW3111400
PROPELLER ADAPTOR WRENCH
Don't over-tighten the
PM3 screws, too much
stress on the screws
could split the firewall.
M3x6mm
d3xD7mm
Washer
1
3
2
E228SXMPO25581107
M5 Nut

Radio Equipment
10
P.7
Canopy
11
PWA2x8mm Screw
4
PM2 x10mm Screw
2
M2 Nylon Insert Lock Nut
2
d2 x D5mm Washer
2
PWA2x8mm
KA1.7x6mm
Elevator Pushrod
Ø1.4x40mm
Rudder Pushrod
Ø1.4x497mm
Straper
Fuel Tube
Ø4x4mm
Rudder Servo
Battery
Elevator Servo
Pushrod Connector
Sponge Front
PM2 x10mm
d2xD5mm
Washer
M2 Nylon Insert Lock Nut
PM2 x10mm
d2xD5mm
Washer
M2 Nylon Insert Lock Nut
Plywood
2x56x95mm
Balsa
1.5x56x205mm
Double-Sided Tape
Brushless ESC
Battery Tie
Mounting Plate
Mounting Plate
Elevator Servo
Pushrod
Connector
J2(Pushrod Ø1.4x443mm)
J1(Pushrod Ø1.4x40mm) J1
J2
Install and arrange the servos as shown in the diagram.
Bottom View
Bottom View
2mm
2mm
1mm
E228SXMPO25581107

P.8
Main Wing
12
Bottom View
Bottom View
Lead to Aileron Servo
Wing Tube
Ø9.6x240mm
Bottom View
Rubber Band
Eye Screw
PA2.5x10x23mm
90°
Bottom
Up
E228SXMPO25581107

P.9
13 Wing Setting
B B'
CC'
400
A A'
A=A' B=B' C=C'
Adjust the wing fuselage configuration as shown in the diagrams.
E228SXMPO25581107

P.10
Adjust the control throws as shown in the diagram.
These throws are good for general flying. You can
adjust according to your personal preference.
15mm
15mm
45mm
45mm
The ideal C.G. position is 90mm (3.54 in.) behind the
leading edge measured at where the wing meets the
fuselage. In order to obtain the C.G. specified, add
weight to the fuselage or move the battery position.
Check the C.G. before flying.
FUN WORLD-EPFUN WORLD-EP
Control Throws
C.G.
Elevator
Rudder
13
14
Ailerons
20mm
20mm
90mm
3.54 in.
Warning!
Important Safety Precautions
# First time flyer should never fly by himself / herself. Assistance from experienced flyer is absolutely necessary.
# Pre-flight adjustment must be done before flying, it is very dangerous to fly a badly pre-adjusted aircraft.
# is specially designed to be powered by KM0283010 Outrunner Motor.
# Make sure the air field is spacious, never fly the plane too close to people and never get too close to a running
propeller. Extreme caution should be exercised when working with electric powered models. Make sure the
propeller is cleared of all objects, especially your hands before connecting the battery to the model. Make sure
you understand the operation of the ESC (Electronic Speed Control) by studying the ESC manual. Once you
plug in the battery for electric powered model, always treat the propeller as a rotating one, as accidental
movement of the throttle stick will spin the propeller and could cause injuries.
# If you find wrinkles on the covering as a result of weather changes, you can use hot iron to remove the wrinkles.
Please begin with lower temperature setting and gradually raise the temperature until the wrinkles are gone.
Too hot an iron may damage the covering. Don't use hot iron near the seams or edges, hot iron will melt the
glue and shrink the covering at the same time, causing the seams to pull away.
# Check and re-tighten up all factory assembled screws, use thread locker if necessary.
E228SXMPO25581107
http://www.theworldmodels.com/para/instruction/instructionManuals.php

Product Registration Form (US Customers)
We would like to share with you any relevant information regarding your model, including
product news and free upgrade parts when applicable. Please fill in the following and send to
AirBorne Models, 4749-K, Bennett Drive, Livermore, CA 94551 USA.
1. Name:
2. Address:
3. Phone #: E-mail:
4. Model:
Wing QC# Fuselage QC#
(QC numbers are stamped on wing and fuselage)
5. Date of Purchase:
6. Store Name:
Please call AirBorne Models at 925 371 0922 for any assistance in filling this form.
Thank you very much for purchasing our product.
E228SXMPO25581107

Large Clevis
Small Clevis
Pl8210010
E228SXMPO25581107

The World Models
Manufacturing Co Ltd., .
www.theworldmodels.com
E228SXMPO25581107