MG International SENSOR SOLAR Technical specifications
Installation and using guide – Page 1/15
DIRECTIONS FOR USE AND INSTALLATION
IMMERSION DETECTORS FOR SWIMMING POOLS
SENSOR PREMIUM / SOLAR / ELITE
READ CAREFULLY AND KEEP THIS INFORMATION FOR FUTURE USE
We thank you to have acquired an immersion detector for swimming pool from Aquasensor range.
Read carefully and entirely the following directions and keep it for future use.
This immersion detector for swimming-pools comply with the French official standard NF P 90-307
WARNING
•This alarm system does not substitute for individual responsibility. It does not aim at substituting for
the parents or responsible adult’s vigilance, which remains the main factor for children under five
protection.
•This alarm is a protection device which signals danger or risk of danger. A fast intervention in less
than 3 minutes of a responsible adult is obligatory when the alarm signal sounds.
In any way, your retailer or the alarm system manufacturer shall not be held responsible for the fall or
the drowning for any person or animal. In no case, the installation of your alarm system shall decrease
your vigilance or replace an active monitoring of the swimming-pool and its accesses.
1 Packaging check list
In spite of the particular care taken to the quality of our products and to their packaging, we invite you to check
the contents of the kit.
Central unit
2 magnetic keys (To get some other magnets, please ask your retailer)
1 alkaline battery 9V (Sensor Premium) or 1 lithium battery (Sensor Solar and Sensor Elite)
1 fixing kit (screws and bolts)
1 test sheet
Terms of the guarantee at the end of this document
SensorDomo (standard remote siren delivered with SensorSolar and SensorElite)
Necessary tools for installation:
•A screwdriver
•A drill
•A Ø8 mm drill bit
•A hacksaw
•A water jerry can (6 to 8 litres) which will be used as mannequin for the tests and later controls
www.alarme-piscine.com
Sécurité des piscines et bassins
ALARME-PISCINE
2 Operating principle
•
Your
alarm
system
is
equipped
wi
th
a technology
whi
ch detects
the
disturbances
and
analyzes the
fall
of a
body
in
yo
ur
po
o
l.
lt
informs
you
by
the
relea
seofa
powerful
si
ren
after a
few
s
ec
onds.
• A
co
ntinuous
analysis
of
its
environment enables
it
to
adapt
its
operation
to
the
surrounding
co
nditi
o
ns
and
thu
s
to
av
o
id in
o
pportune
releases.
•
Pour
votre
confortetvotre s
éc
urité
,
il
di
spo
se
des
modes
de
fon
ctionnement décrits
ci
-
après
.
•
For
your comfort
and
your safety,
it
display
s
the
foll
o
wing
op
e
rating
mode
s:
Description
of
the
operating modes
Means
of
identification
"Active monitoring" •
The
l
ed
bes
ide
the
sw
i
mmer
symbol
is
off
• The a
larm
starts
when
a
body
fa
li
s i
nto
the
sw
i
mming
pool.
•
The
si
r
en
emitsat least a 1
OOdB
s
ignal.
"
Inacti
ve monitoring" The l
ed
bes
idethe
sw
i
mmer
symbol
is
flashing
The
alarm
will
not
sta
rt
whi
le
flash
i
ng
, e
ven
if a body
falls
into
the
sw
i
mming
-
pool.
•
Allow
s to
make
the siren
in
o
pera
t
ive
duri
ng
the
bath.
The
user selects •
this
mode
by
app
lying t
he
magnet
on
the swimmer
symbol
located
on
•
the s
ti
cker
on
the
top
of
the
device
(SensorPremium
) or at the
back
of
thedevice (SensorSolar, Se
ns
orE
li
te
) beforeentering the
pool.
• A 3 seconds
long
beep
ind
icates that the
devi
ce switches
to
the
acti
ve
monitoring
mode.•
Th
e device
is
programmed
to leave this
mode
and reset
in
"active
monitoring"
mode
alter 1 minute 30 seconds, period
which
starts
when
the
pool
is totally
cairn.
•
The
de
vice alwa
ys
swit.ches
to
thl
s mode
when
y
ou
eut
the
s
iren
off.
•
The
dev
ic.e
always s"'itc.hes
to
thl
s
mode
when
you leave
the
s
top
mode
If
the
us
er tries to
switch
manually
to
the "
acti
ve monitoring"
mode
•
with the
magnet
and
the
pool
is
not
cairn
enough
, the device
will
au
t
oma
tically
switch
to
the inactive
mon
it
or
i
ng
mode.
A 3 seconds l
ong
beep i
mmediately
followed
by
a sequence of 10
short beeps i
ndicates
that the
pool
is
too
ag
it
ated
for
an
active
monitor·ing.
lt
will r·
emain
in
ina
c
ti
ve monitoring
until
the
pool
is
totall
y calm.
"Dis
turbed
active monitoring"
•
Might
happen
d
uri
ng
the «
acti
ve monitoring»
mode
Be
patient. it
is
som
etimes necessary
to
wa
it
more
than
10
mi
nutes
for
the
lona
beeo
to
sound
afler the bath.
• A specific
long
beep
is
emitted
by
t
he
dev
ice, the
pool
is
ag
itated, the
mon
itori
ng
is
still active.
• Disturbances
which
are not
due
to
a
fall
are detected in the
pool.
The
pool
analysis
becornes
more
accurate,the detecti
on
t
ime
may
be longer. • A short str
ong
beep
is
emitted
by
the device,
the
poo
l is very
agitated, the monitoring
is
still
ac
ti
ve but yoo
ha
ve
to
chec.k y
om
·• The device
au
tomatically switches to the "active
mon
itori
ng
"
mode
once
t
he
pool
is
cairn.
«S
top
»
pool.
• A succession of
10
short
high
beeps
i
ndicates
the
switch
to the
"inact
ive
mon
itori
ng
"
mode
when
the
pool
is
too
agitated.
• This
mode
allows a t
otal
eut off
of
the device.
There
is
not
any
• N
ei
ther l
uminous
signal
nor
sound
signal
is
emitted
even
if a
fall
automatic reactivation afl
er
that
mode
~
NEVER
LEA
VE
THE
POOL
WITHOUT
HUMAN
.MONITORINGUNDER
THAT
MODE
"
Te
st mode "
• Temporary
mode
which
allows the al
arm
ad
ju
strnen
t withoutdisturbing •
The
siren is
in
low
power
mode
when
it
se
ts off
the
neighbourhood
as
the
siren
is
in
low
power
mode.
• The operation of the device
is
comp
letely identical
to
its
usual
operati
on
(active
mon
it
or
i
ng,
inactive
monitoring)
.
On
ly the siren
vo
l
ume
changes.
•
This
mode
automa
tically operates
when
mak
i
ng
the battery
connec
t
ion
.
•
The
dev
i
ce
l
eave
s the test
mode
autornat
i
ca
ll
y afler 30 minutes
(I
f
no
handling
of
the
dev
ice) • A specific
low
powersound signal
is
emitted for 5 seconds
N
EVER
LEA
VE
THE
POOL
WITHOUT
HUMAN
.MO
N
ITORING
UNDER
THAT
MODE
Regularly
refer
to this chapter, especially
if
you
do
not
obtain
the
specified
results.
Installation
and
us
i
ng
guide - Pa
ge
2/
15
www.alarme-piscine.com
Sécurité des piscines et bassins
ALARME-PISCINE
Installation and using guide – Page 3/15
3 Magnet use
Locate the swimmer symbol situated in the activation zone of the device:
SensorPremium: on the top of the lid
Sensor Solar and SensorElite: At the back side of the base
During the installation steps and for a daily use, you will have to apply the magnet on that symbol.
The magnet must absolutely be placed out of reach of the children.
•Manual switch from inactive monitoring to active monitoring
•Apply the magnet on the swimmer
You obtain a high long beep and the led stops flashing.
•Manual switch from active monitoring to inactive monitoring
•Apply the magnet on the swimmer
You obtain a 10 high beeps sequence and the led flashes slowly.
•Switch to the stop mode (Get the two provided magnets)
•Apply one of the magnets on the red stop. When obtaining a continuous luminous signal, keep the first
magnet in position and apply the second magnet on the swimmer.
•When obtaining the sound signal (10 high beeps), remove the two magnets. A fast luminous flashing
signal indicates the complete stop of the device.
•
•Stop mode ending
•Apply the magnet on the swimmer
You obtain a 10 short beeps sequence, the device operates in the inactive monitoring mode. To operate
www.alarme-piscine.com
Sécurité des piscines et bassins
ALARME-PISCINE
Installation and using guide – Page 4/15
4 Installation, tests and adjustments
4.1 Position choice
•Depending on the location of the house from the swimming-pool, it might be necessary to displace the
security signals, warning and failure signals so that they can be clearly audible from the house. This must be
checked during the installation of the unit.
•Before fixing and to allow adjustments, the detection unit must be placed on the curb stone and necessarily
positioned in the middle of the longest length of your pool. An installation on a flat surface is not essential.
EXAMPLES of placement of the central unit :
: Indicative location of your central unit
Warning: The location of the central unit can influence the time of detection of a fall
•For large swimming-pools models, it might be necesary to instal several detection central (Ask your retailer
for advice)
•Take care that the detection central is not placed more than one meter far from the filtration system or a water
cascade.
•Make sure that the access to the activation zone (magnet application zone) is easy and practical.
•The probe must be 15 to 20 cm submerged. (ideally 18 cm) to ensure an optimal operation. If necessary, cut
the probe with care to the adviced length with a hacksaw.
Warning : Regularly check the water level and complete it if necessary to keep a submersion depth between 15
and 20 cm.
t
r
a
l
u
n
i
t
:
15/20cm
Or
www.alarme-piscine.com
Sécurité des piscines et bassins
ALARME-PISCINE
Installation and using guide – Page 5/15
4.2 Activation – Tests
4.2.1 Activation
• Unscrew and withdraw the lid
• SensorPremium:
www.alarme-piscine.com
Sécurité des piscines et bassins
ALARME-PISCINE
Installation and using guide – Page 6/15
Your device is not yet operational, after the installation of the battery you have 30 minutes to carry out
the tests and adjustments specified hereafter. During these 30 minutes the siren is in low power mode (test
mode).
IMPORTANT
•When you purchase the device, the central unit is preset for a rectangular pool, 4X8 meters long and 1,40
meters deep (most common standard pools – French standard NF P 90-307)
•Some 4X8 meters swimming-pools do not correspond precisely to these recommendations. In order to
optimize the device performances to your pool, it is possible to benefit from adjustments possibilities of the
device (advanced tests).
•Nevertheless, before any intervention on the preset adjustments, it is advised to carry out the bases tests.
•In order to obtain an optimal adjustment of your device, we advice you to carry out all these tests, in a
completely calm pool, with the lid in position (You do not have to screw it, except if there is some wind)
•Before any test, make sure your central unit is in « active monitoring » mode (no flashing of the led). If it is
not the case, apply the magnet on the swimmer until you obtain a long beep and the led stops flashing.
•WARNING: If you hear short beeps after the long beep and the led is still flashing, the device automatically
switches to « inactive monitoring » mode, the pool is too agitated to allow a correct analysis. It is advised to
start again the operation once the pool is calm.
•For the following tests, when the siren sets off: apply the magnet on the swimmer until the alarm stops.
4.2.2 Basic tests
• Test 1 : Filtration
•Leave your central unit on for 10 minutes while the filtration is operating.
•If the device automatically switches to « inactive monitoring » mode (10 short beeps sequence + flashing
led), the preset adjustment is not suitable for your pool, please, go directly to the advanced tests (paragraph
4.2.3)
•
• Test 2 : Robot
•Leave your central unit on while the robot is operating in the pool.
•If the device automatically switches to inactive monitoring mode (10 short beeps sequence + flashing led) ,
the preset adjustment is not suitable for your pool, please, go directly to the advanced tests (paragraph
4.2.3)
•WARNING: Some cleaning robots which climb to the water line (Robots which go in and out of the water
and cause an event which might be considered like the fall of a child in the pool) are incompatible with
immersion detection systems.
• Test 3 : Fall
•Simulate the fall of a body in the pool by making a child or a 6-8 litres water jerry can or the dummy from
your retailer from the curb stone. The alarm must set off within 12 seconds maximum after the fall.
• Fall detected within 12 seconds : stop the alarm
• Fall not detected or detected in more than 12 seconds : go to the advanced tests (paragraph 4.2.3)
If you passed the whole basic tests successfully, go directly to paragraph 4.2.4
www.alarme-piscine.com
Sécurité des piscines et bassins
ALARME-PISCINE
Installation and using guide – Page 7/15
4.2.3 Advanced tests
Tests are to be carried out only if the basic tests were not carried out successfully.
•These tests aim at obtaining an optimal configuration (operating) of the device for your pool. You will need
to modify the preset adjustment of your device.
•In order to make that adjustment, SensorPremium, SensorSolar and SensorElite are equipped with a
dipswitch setting. For a given size of pool, a preset combination of the switch position is fitted (ON or OFF)
Sensor Premium
Setting under the electronic card on the left side
• Test 1 : Filtration
•Leave your central unit on for 10 minutes while the filtration is operating.
•If the device automatically switches to « inactive monitoring » mode (short beeps sequence + flashing led),
go to the preceding adjustment (example: switch from D to C) and start again this test.
• Test 2 : Robot
•Leave your central unit on while the robot is operating in the pool.
•If the device automatically switches to inactive monitoring mode (short beeps sequence + flashing led) , go
to the preceding adjustment (example: switch from D to C) and start again this test.
•WARNING: Some cleaning robots which climb to the water line (Robots which go in and out of the water
and cause an event which might be considered like the fall of a child in the pool) are incompatible with
immersion detection systems.
Pool size
Adjustments
1
2
3
4
5
A OFF ON ON ON OFF
B OFF ON ON OFF ON
3 X 6 meters C OFF ON ON OFF OFF
4 X 8 meters
Factory
adjustment D OFF ON OFF ON ON
E OFF ON OFF ON OFF
5 X 10 meters F OFF ON OFF OFF ON
6 X 12 meters
G
OFF
ON
OFF
OFF
OFF
ON
OFF
www.alarme-piscine.com
Sécurité des piscines et bassins
ALARME-PISCINE
Installation and using guide – Page 8/15
• Test 3 : Fall testing
•Simulate the fall of a body in the pool by making a child or a 6-8 litres water jerry can or the dummy from
your retailer, fall from the curb stone. The alarm must set off within 12 seconds maximum after the fall.
• Fall detected within 12 seconds : stop the alarm
• Fall not detected or detected in more than 12 seconds: go to the following adjustment (Example:
switch from D to E) and start again from the first test.
If you passed the whole tests successfully, go to paragraph 4.2.4
4.2.4 Exit from test mode
•When the whole tests have been passed successfully, it is necessary to wait at least for 30 minutes, without
any use of the device to leave quit the test mode. This is notified by a specific 5 seconds low power signal.
•If the device leaves quits the test mode before the end of the tests, withdraw the battery and wait for a few
minutes before connecting it again to restart the test mode.
Your detection unit is now in active mode, the led is off
• It is required to carry out complementary tests; the siren will set off loudly (100 dBA minimum) if
ever a fall happens. Check you can hear it from the house. If you can not hear it, install the remote
siren in the house (Sensor domo delivered with SensorSolar and SensorElite). Stop the alarm by
applying the magnet on the swimmer, the red led will flash.
• Wait for the long beep and for the led to switch off before testing another fall. It may sometimes be
necessary to wait for a few minutes.
If, in spite of that, you do not manage to adjust the device to your pool, do not hesitate to contact your retailer
www.alarme-piscine.com
Sécurité des piscines et bassins
ALARME-PISCINE
Installation and using guide – Page 9/15
4.3 How to fix your device to the curb stone
• Set your device in « inactive monitoring » mode
• Withdraw the lid from the base
• Mark out the 4 fixing points in the base (1)
• Position the device so that the probe is 0,5 cm from the edge of the curb stone. Mark out with a felt pen the
position for the holes to drill in the curb stone.
• Drill the 4 holes with an Ø8mm drill bit. Position the 4 raw plugs (2)
• Position the 4 stabilizing foam (3) under the base in the housings.
• Position the base and screw the device with the screws (3) and the screw covers (5) provided. (screw covers
must beplaced inside the base)
• Place the small black round joints (6) provided in the bag on each screwing tube (7) of the base.
• Replace the lid, screw it with the screws provided (Do not use an electrical drill) and position the cap
provided.
• Check the good operating of the alarm again by making a jerry can or a dummy fall in the water.
JOINT
(6)
SCREW COVERS
(5)
Ø5 CONCRETE SCREW
(4)
STABILIZING FOAM
(3)
RAWLPLUG
(2)
Ø8 HOLE IN THE CURBSTONE
0,5 cm mini
BASE
(1)
SCREWING tubes
(7)
www.alarme-piscine.com
Sécurité des piscines et bassins
ALARME-PISCINE
Installation and using guide – Page 10/15
5 Daily use
5.1 Normal use
•Switch to inactive monitoring mode: Apply the magnet on the swimmer symbol until you obtain 10 short
beeps.
In inactive monitoring mode, the luminous signal is flashing.
We point out that the device automatically switches to the active monitoring mode 1 min 30 seconds after the
pool is calm. (Be patient, it might take 10 minutes, more or less).
During that period, human monitoring must take over.
5.2 Complete stop
•Complete stop: Apply one of the magnets and maintain it on the red stop on the sticker. When obtaining a
continuous luminous signal, apply the other magnet on the swimmer symbol. A sequence of high beeps and a
luminous signal flashing fast indicates the deactivation of the device.
•To leave the complete stop mode: Apply the magnet on the swimmer symbol. You switch then to the
inactive monitoring mode.
WARNING for winter usage (only in case of temperatures under 0°C)
• Your alarm system is inoperative if the water in the probe is frozen.
•
www.alarme-piscine.com
Sécurité des piscines et bassins
ALARME-PISCINE
Installation and using guide – Page 11/15
5.4 Monthly tests
In order to check the good operating of your Sensor Premium, Sensor Solar or Sensor Elite, it is imperative to
proceed monthly to the basic tests (paragraph 4.2.2) and to note the results in the form provided in the
installation guide.
In case of problem, immediately contact your retailer.
Retailer address: ……………………………………………………………………………………………………
Owner’s name: ……………………………………………………………………………………………………..
Purchase date: ………………………………………………………………………………………………………
GUARANTEE AND AFTER SALE SERVICE
5.5 Additional information
It is essential that appropriate surveillance is carried out by parents
SAFETY INFORMATION
It is imperative to react when the failure signal sounds. The user who switches the system off must be conscious that human monitoring must
take over. The greatest vigilance of a parent or of a responsible adult is necessary between the end of the swim and the reactivation of the
alarm system. In no case can your retailer or the manufacturer of this alarm system be held responsible for the fall or of the drowning of a
child, a dependent person, any adult or animal. The installation of the alarm system must in no case diminish your vigilance or replace an
active supervision of the swimming pool and its accesses.
This alarm system, as any other device or safety equipment, is a complementary tool useful in case of temporary lack of supervision.
SAFETY ADVICE
The safety of your children depends on you!
The maximum risk is when the children are under the age of 5 years.
Accidents do not only happen to others! Be prepared!
Monitoring and action
•The supervision of children must be constant and close
•Choose just one adult to be responsible for security.
•Be even more vigilant when there are several other users of the swimming pool.
•Teach children how to swim as soon as possible.
•Wet the nape of the neck, the arms and legs before entering the water.
•Become knowledgeable about\ First Aid, especially specific to children.
•Forbid diving and jumping in the presence of young children.
•Forbid running and horseplay around the pool
•Do not allow access to the pool without life jacket to a child who can’t swim or with no one to
accompany him in the water.
•Do not leave toys around or in the non monitored swimming pool.
•Keep the water permanently clean and clear.
•Store the water treatment products out of the reach of children.
•To prevent children younger than 5 years old having access to the pool when the failure signal sounds,
•Take any measure of security necessary until the device is repaired.
•The monitoring of the pool must be constant and close.
www.alarme-piscine.com
Sécurité des piscines et bassins
ALARME-PISCINE
Installation and using guide – Page 12/15
Anticipate!
> have an accessible phone near the pool so you don’t have to leave your children without monitoring to answer
the phone
> have a buoy and a pole near the pool
In case of an accident
> Take the child out of the water as quickly as possible
> Immediately call the emergency services and follow the advice they give you
> Replace the wet clothes by warm blankets
Immersion time and chance of survival (figures given by the French Safety Services and used as a reference by officials)
Duration of
immersion
Ratio
1 minute 95 %
2 minutes 80 %
3 minutes 65%
4 minutes 25 %
5 minutes 1 %
The speed of intervention after the alarm has sounded is crucial. Don’t ever leave the pool if a child plays
nearby. It’s the combination of a passive monitoring (alarm system) and an active monitoring (by the parents or
responsible adults) that insure a high security level. The zero risk doesn’t exist. Installing this alarm system must
not decrease your vigilance or replace active and visual monitoring of the swimming pool.
www.alarme-piscine.com
Sécurité des piscines et bassins
ALARME-PISCINE
Installation and using guide – Page 13/15
5.6 GUARANTEE AND AFTER-SALES SERVICES (French model)
Your immersion detector system is guaranteed for 2 years (Detection Unit and remote siren).
Be sure that children or animals are not present when installing your device.
GUARANTEE COVER
MG International or its retailers will provide to the buyer of this product the services listed below:
MG International, manufacturer, guarantees that immersion detectors do not have any default of material or manufacture during the period
stipulated hereafter, until the purchase date:
Central Unit: 2 years, labour and materials
Remote Siren: 2 years, labour and materials
The consumables (batteries, dehydrating packets, magnets...) included in the original package that appears to have faulty manufacture or
material will be replaced for free during a period of 90 days from the purchase date.
If the client user sells the immersion detector during the guarantee period, the guarantee will be considered cancelled. No guarantee of a
proper installation or shipping can be given to the new owner. This will be considered an agreement from the new owner.
In order for the contractual time and material guarantee to be applicable, it is mandatory to follow conditions below:
The installation must conform to the instructions or be made by an installer approved by MG International,
The installation tests must have been carried out and the tests sheets must be sent by registered mail to your retailer within the 7 days of the
purchase date (Postmark being proof + copy of the invoice)
The components of your alarm system must be undamaged
The Regular maintenance of the siren and control Unit (verifying that the unit is in working order with regular tests and monthly update of
the maintenance card) must be undertaken
Make regular immersion tests (once a month). Do not hesitate to inform your retailer in case of failure.
Follow the installation instructions
In case of necessary repair
In case of failure, the client must verify if there’s a problem with the material or the manufacture of the device. If, after being returned to the
after-sales service, no fault with material or manufacture of the device was found by the technicians, MG International reserves the right to
charge for this service.
If the immersion detector appears to be faulty within the guarantee because of material or the manufacture of the device, MG International
will replace or repair the Unit providing that the client produces a copy of the original receipt. MG International reserves the right to
refuse to provide this service or to charge for the cost of repairs.
If the receipt is not produced, MG International reserves the right to refuse to provide a service or charge for the cost of maintenance and
repairs.
In case of technical difficulties with the devices, the client must immediately contact his retailer or otherwise MG International. When
calling, the client must be able to describe the problem in detail so that the retailer or an after-sales service representative can determine if
repair is necessary. The client must indicate to the representative the precise date and place of the purchase (town, name and address of the
retailer). If writing, the client must clearly describe the problem, the date and place of the purchase and clearly state his personal details.
MG International reserves the right to replace the repairable parts by new or as new parts. In case the device or its parts are unserviceable for
more than 7 days in a workshop or at the place of installation, the guarantee will be prolonged for the unserviceable period. This period will
start from the day the device has been taken charge of by the after-sales service certified by MG International or the day the client has asked
for it to be repaired.
During the unserviceable period, it is at the discretion of the retailer whether to provide a replacement. Neither the retailer, nor MG
International is obliged to replace the unserviceable device. Be sure to enforce active monitoring of your pool during this period.
EXCLUSIONS TO THE GUARANTEE
The guarantee is not applicable to products from which the original identification labels have been removed or modified and is not applicable
in case of faults or failures due to accident, negligence or abusive use, a failure of the electrical supply; of an external electrical circuit; of
lightning; the use of components not supplied by MG International; a prolonged immersion that has damaged one or more of the
components; unusual physical or electrical stress; the modification, the set up, the repair, the maintenance or the installation of a component
by anyone other than representatives of MG International or its subcontractors and certified retailers or due to any other cause that, to the
discretion of MG International, is not the result of faulty material or manufacture.
This guarantee replaces any other guarantees, explicit or implicit, and the responsibility of MG International on the basis of this guarantee is
limited to the replacement or the repair of the device (including the remote siren). MG International is especially not obliged to replace or
repair the device if it is defective for the reasons described in this guarantee. MG International won’t be IN ANY CASE and ANY
CIRCUMSTANCES be held responsible for any other costs, fees, expenses, loss or damage (indirect or otherwise) of any nature. Moreover,
in the case the device being brought back or returned to MG International with modifications, damage of any nature or removal of
components, MG International will be able to refuse to honour the guarantee of the device and won’t be obliged to replace or repair it.
www.alarme-piscine.com
Sécurité des piscines et bassins
ALARME-PISCINE
Installation and using guide – Page 14/15
This guarantee constitutes the whole responsibility of MG International regarding the provided products and services on the basis of this
guarantee. MG International won’t provide any obligation, duty or responsibility, whether contractual or sub contractual (responsibility for
negligence included) or others to the client.
It is necessary to remind you that some climatic conditions can destabilize your device. In these situations make sure that your child does not
come near the pool. Avoid leaving your device unused for long periods.
Regularly check the correct operation of your device by carrying out the tests indicated in this guide.
MG International‘s obligation is only to provide the client with an operational device, without any fault of material or manufacture. MG
International can’t be held responsible for the fall, the drowning of a child, adult or any animal. The monitoring of parents remains the best
security solution for children.
Immersion detectors can’t replace common sense and individual responsibility. They cannot replace
the vigilance and responsibility of parents or responsible persons that are still the essential element in
the protection of children or dependant persons.
Products AQUASENSOR or AQUAPREMIUM
References PRE004
SEN004
Manufacturer MG International
SAV. ZI Athélia II 13600 La Ciotat -France
Tel. +33.4.42.98.14.90 export@aquasensor.com
www.alarme-piscine.com
Sécurité des piscines et bassins
ALARME-PISCINE
This manual suits for next models
2
Table of contents
