Mi Redmi Note 13 5G User manual

Redmi Note 13 5G
Quick Start Guide
SAT. 16 AUG.
02
48
Volume
Buons
Power
Buon
USB Type-C Port
Nano-SIM
Nano-SIM
Nano-SIM
Micro SD
To view the user guide, scan the QR code.

Thank you for choosing Redmi Note 13 5G
Long press the power buon to turn on the device.
Follow the on-screen instructions to configure the device.
For more information, visit our official website:
www.mi.com/global/service/userguide
About SIM :
Please do not insert non-standard SIM cards into the SIM card slot. They may damage the
SIM card slot.
WARNING: Do not disassemble this device.
WEEE
Special precautions must be taken to safely dispose of this product. This
marking indicates that this product may not be discarded with other
household waste in the EU.
To prevent harm to the environment or human health from inappropriate
waste disposal, and to promote sustainable reuse of material resources,
please recycle responsibly.
To safely recycle your device, please use return and collection systems or contact the
retailer where the device was originally purchased.
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO INSTRUCTIONS.
To prevent possible hearing damage, do not listen at high volume levels for long
periods.
Additional safety information and precautions can be accessed at the following
link: www.mi.com/en/certification
Important Safety Information
Read all safety information below before using your device:
• Use of unauthorized cables, power adapters, or baeries can cause fire explosion,
electric shock, pose other risks, or damage the device.
• This device’s operating temperature range is 0°C to 40°C. Using this device in an
environment outside of this temperature range may damage the device.
• If your device is provided with a built-in baery, to avoid damaging the baery or the
device, do not aempt to replace the baery yourself.
• Charge this device only with the included or authorized cable and power adapter.Use
only authorized accessories which are compatible with your device.
• Aer charging is complete, disconnect the adapter from both the device and the power
outlet. Do not charge the device for more than 12 hours.
• The baery must be recycled or disposed of separately from household waste.
Mishandling the baery may cause fire or explosion. Dispose of or recycle the device, its
baery, and accessories according to your local regulations.
• Do not disassemble, hit, crush, or burn the baery. If the baery appears deformed or
damaged, stop using it immediately.
-Do not short circuit the baery, as this may cause overheating, burns, or other injury.
-Do not place the baery in a high-temperature environment.
-Overheating may cause explosion.
-Do not disassemble, hit, or crush the baery, as this may cause the baery to leak,
overheat, or explode.
-Do not burn the baery, as this may cause fire or explosion.
• User shall not remove or alter the baery. Removal or repair of the baery shall only be
done by an authorized repair center of the manufacturer.
• Keep your device dry.
• Do not try to repair the device yourself. If any part of the device does not work properly,
contact Mi customer support or bring your device to an authorized repair center.
• Connect other devices according to their instruction manuals. Do not connect
incompatible devices to this device.
• For AC/DC adapters, the socket-outlet shall be installed near the equipment and shall
be easily accessible.
Safety Precautions
• Observe all applicable laws and rules restricting use of mobile phones in specific
situations and environments.
• Do not use your phone at petrol stations or in any explosive atmosphere or potentially
explosive environment, including fueling areas, below decks on boats, fuel or chemical
transfer or storage facilities, or areas where the air may contain chemicals or particles
such as grain, dust, or metal powders. Obey all posted signs to turn off wireless devices
such as your phone or other radio equipment. Turn off your mobile phone or wireless
device when in a blasting area or in areas requiring “two-way radios” or “electronic
devices” to be turned off to prevent potential hazards.
• Do not use your phone in hospital operating rooms, emergency rooms, or intensive care
units. Always comply with all rules and regulations of hospitals and health centers. If
you have a medical device, please consult your doctor and the device manufacturer
to determine whether your phone may interfere with the device’s operation. To avoid
potential interference with a pacemaker, always maintain a minimum distance of 15 cm
between your mobile phone and the pacemaker. This can be done by using your phone
on the ear opposite to your pacemaker and not carrying your phone in a breast pocket.
To avoid interference with medical equipment, do not use your phone near hearing aids,
cochlear implants, or other similar devices.
• Observe all aircra safety regulations and turn off your phone on board aircra when
required.
• When driving a vehicle, use your phone in accordance with relevant traffic laws and

regulations.
• To avoid being struck by lightning, do not use your phone outdoors during
thunderstorms.
• Do not use your phone to make calls while it is charging.
• Do not use your phone in places with high humidity, such as bathrooms. Doing so may
result in electric shock, injury, fire, and charger damage.
• Connect the “Redmi Note 13 5G” to computer using a USB data cable.
• Use the USB cable included in the gi box with a Mi brand charger (maximum output of
less than 33W) and then connect it to a power strip.
• You can also use any third-party charger that complies with USB2.0 or higher protocol
standards and also meets the requirements of the International Information Technology
Equipment Safety Standard (IEC 60950), Audio/video, Information and Communication
Technology Equipment Standard (IEC 62368-1) and the related laws and regulations of
your country or region.
• Please note that the product allows the use of chargers with the maximum output of
33W. The maximum voltage shall not exceed [11V] and the maximum current shall not
exceed [3A].
• Using other chargers that do not meet the above requirements to charge this product
may damage the product itself and your personal or property safety.
Security Statement
Please update your phone’s operating system using the built-in soware update feature,
or visit any of our authorized service outlets. Updating soware through other means may
damage the device or result in data loss, security issues, and other risks.
EU Regulations
RED Declaration of Conformity
Xiaomi Communications Co., Ltd. hereby declares that this GSM / GPRS / EDGE / UMTS /
LTE / 5G NR Digital Mobile Phone with Bluetooth and Wi-Fi 2312DRAABG is in compliance
with the essential requirements and other relevant provisions of the RE Directive 2014/53/
EU. The full text of the EU declaration of conformity is available at the following internet
address:
www.mi.com/en/certification
RF Exposure Information (SAR)
This device is in compliance with Specific Absorption Rate (SAR) limits for general
population/uncontrolled exposure (Localized 10-gram SAR for head and trunk, limit: 2.0W/
kg) specified in Council Recommendation 1999/519/EC, ICNIRP Guidelines, and RED
(Directive 2014/53/EU).
During SAR testing, this device was set to transmit at its highest certified power level in
all tested frequency bands and placed in positions that simulate RF exposure during use
against the head with no separation and near the body with a separation of 5 mm.
SAR compliance for body operation is based on a separation distance of 5 mm between the
unit and the human body. This device should be carried at least 5 mm away from the body to
ensure RF exposure level is compliant or lower than the reported level. When aaching the
device near the body, a belt clip or holster should be used which does not contain metallic
components and allows a separation of at least 5 mm to be maintained between the device
and the body. RF exposure compliance was not tested or certified with any accessory
containing metal worn on the body, and use of such an accessory should be avoided.
Certification Information (Highest SAR)
SAR 10 g limit: 2.0 W/Kg,
SAR Value: Head: 0.943 W/Kg, Body: 0.998 W/Kg (5 mm distance).
Legal Information
This device may be operated in all member states of the EU.
Observe national and local regulations where the device is used.
This device is restricted to indoor use only when operating in the 5250 to 5350 MHz
frequency range in : AT,BE,BG,HR,CY,CZ,DK,EE,FI,FR,DE,EL,HU,IE,IT,LV,LT,LU,MT,
NL,PL,PT,RO,SK,SI,ES,SE,UK(NI),IS,LI,NO,CH,TR
Wi-Fi connectivity (including Wi-Fi frequency bands, Wi-Fi standards and other features as
ratified in IEEE Standard 802.11 specifications) may vary based on regional availability and
local network support.The function may be added via OTA when and where applicable.
Restrictions in the 2.4 GHz band:
Norway: This subsection does not apply for the geographical area within a radius of 20 km
from the centre of Ny-Ålesund.
Please ensure the used power adapters are compliant with applicable country regulations
and international and regional safety standards.
Frequency Bands and Power
This mobile phone offers the following frequency bands in EU areas only and maximum
radio-frequency power:
GSM 900: 35.5 dBm
GSM 1800: 32.5 dBm
WCDMA band 1/8: 25.7 dBm
LTE band 1/3/7/8/20/28/38/40/41: 25.7 dBm
5G NR band n1/n3/n7/n8/n20/n28/n38/n40/n41: 26 dBm, 5G NR band n77/n78: 29 dBm
Bluetooth: 20 dBm
Wi-Fi 2.4 GHz band: 20 dBm
Wi-Fi 5 GHz: 5150 to 5250MHz: 23 dBm, 5250 to 5350 MHz: 20 dBm, 5470 to 5725 MHz: 20
dBm, 5725 to 5850 MHz: 14 dBm

NFC: 13.56 MHz < 42 dBuA/m at 10m
5G connection depends on country, carrier, and user environment.
FCC Regulations
This mobile phone complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause
undesired operation.
This mobile phone has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in
a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
RF Exposure Information (SAR)
This device meets the government’s requirements for exposure to radio waves. This
device is designed and manufactured not to exceed the emission limits for exposure to
radio frequency (RF) energy. The exposure standard for wireless devices employs a unit of
measurement known as Specific Absorption Rate, or SAR.
The SAR limit set by the FCC is 1.6 W/Kg. For body-worn operation, this device has been
tested and meets the FCC RF exposure guidelines for use with an accessory that contains
no metal and positions the device a minimum of
1.0 cm from the body. RF exposure compliance with any body-worn accessory that contains
metal was not tested and certified, and use of such body-worn accessory should be
avoided. Any accessory used with this device for body-worn operation must keep the device
a minimum of 1.0 cm away from the body.
FCC Note
Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Shielded cables must be used with this unit to ensure compliance with the Class B FCC
limits.
E-label
This device has an electronic label for certification information.
To access it, please go to Seings > About phone > Certification, or open Seings and type
“Certification” into the search bar.
Model: 2312DRAABG
2312 indicates that this product will be launched aer 202312.
Disclaimer
This quick start guide is published by Xiaomi or its local affiliated company. Improvements
and changes to this guide necessitated by typographical errors, inaccuracies of current
information, or improvements to programs and/or equipment, may be made by Xiaomi
at any time and without notice. Such changes will, however, be incorporated into new
online editions of the quick start guide (please see details at www.mi.com/global/service/
userguide). All illustrations are for illustration purposes only and may not accurately depict
the actual device.
Manufacturer: Xiaomi Communications Co., Ltd.
Manufacturer postal address:
#019, 9th Floor, Building 6, 33 Xi’erqi Middle Road,
Haidian District, Beijing, China, 100085
Brand: Redmi Model: 2312DRAABG
© Xiaomi Inc. All rights reserved.