Mianyang Weibo Electronic WBV411S07 User manual

Designing, Manufacturing and Supplying WB Series Electric Isolated
Transducer and Digital Electrical Transducer since 1989
USER MANUAL
WBV411S07 AC Voltage Transducer
www.wb-my.com
[email protected]
Tel: [phone]
Fax: [phone]
ISO9001 ISO14000 ISO18000
Certified

WBV411S07 AC voltage transducer
Safety claim
The information in the safety claim of the equipment documentation is
intended to ensure that equipment is properly installed in order to
maintain it in a condition.
It is assumed that everyone who will be associated with the equipment
will be familiar with the contents of that safety section, or this safety
guide.
When electrical equipment is in operation, dangerous voltages will be
present in certain parts of the equipment (e.g. the input terminal). Failure
to obverse warning notices, incorrect use, or improper use may endanger
personnel and equipment and course personal injury or physical damage.
Before working in the terminal strip area, the equipment must be isolated.
Proper and safe operation of the equipment depends on appropriate
shipping and handling, proper storage, installation and commissioning,
and on careful operation, maintenance and servicing.
The operating manual for the equipment gives instructions for its
installation, commissioning, and operation. However, the manual cannot
cover all conceivable circumstances or include detailed information on all
topics. In the event of questions or specific problem, do not take any
action without proper authorization. Contact the appropriate WB
technical or sales office and request the necessary information.
Standard application
1. Accuracy
Accurate degree is conformed to IEC688:1992
2. Safety
2.1 Overload capability
Overload capability is conformed to IEC688:1992
2.2 Isolation voltage
Can be endured testing voltage is conformed to
Q/72085584-0.1-2004
2.3 Insulation impedance
The insulation impedance is no less than 20M Ohm, is conformed to
Q/72085584-0.1-2004
3. Electromagnetic Capability

3.1.Electromagnetic field immunity test according to IEC
61000-4-3:1995
3.2 Power frequency magnetic field immunity test according to IEC
61000-4-8:1993
Product Description and Application
WBV411S07 converts AC input voltage into a load independent output
tracing voltage 5V. It has adopted photoelectrical isolation principle for
real time measurement of AC voltage from electric net or electric circuit.
The product has certain advantages of total galvanic isolation between
input/output, high accuracy, low drifting by temperature, and wide
temperature bearable range, etc.
Product Dimensional Drawing (unit: mm)
DIN mounting rail
Input terminal
Mianyang Weibo Electronic Co., Ltd
No.7 Road second part of Xianren Road, Youxian District, Mianyang City, Sichuan province P.R. China
Tel: [phone] Fax: [phone]
www.wb-my.com [e-mail]

Product Terminal Identification Drawing
4
AC voltage input (U+)
1
3
3
4
6
6
1
AC voltage input (U-) Power supply positive (+E)
Tracing voltage output (Ug)
Tracing voltage output ground (GND)
Power supply negative(-E)
Non-identified terminals cannot be used
Key Technical Data:
1. Input: AC 0~1000V
2. Output: Tracing voltage output 5V
3. Frequency range: DC~10kHz
4. Accuracy : 0.2%
5. Input Impedance (R): Measurement Ux≤1V, Ri≥1MΩ
Measurement Ux＞1V, Ri＝Ux×10kΩ/V
6. Linear Range:0~120% of nominal input
7. Responding Time: 15μs
8. Over Load Capacity: 2 times of nominal input, continuous;
9. Output current: 5mA
10.Static current: 25mA ;
11.Auxiliary Power: DC ±12V,±15V
12.Isolation Voltage(Input/Output): ≥1500Vdc, for 1 minute ;
13.Output Ripple: ＜10mv (output load is 250Ω) ;
14.Drifting by Temperature: 150ppm
Mianyang Weibo Electronic Co., Ltd
No.7 Road second part of Xianren Road, Youxian District, Mianyang City, Sichuan province P.R. China
Tel: [phone] Fax: [phone]
www.wb-my.com [e-mail]

Mianyang Weibo Electronic Co., Ltd
No.7 Road second part of Xianren Road, Youxian District, Mianyang City, Sichuan province P.R. China
Tel: [phone] Fax: [phone]
www.wb-my.com [e-mail]
15.Ambient Temperature: -10℃～+50℃
16.Mounting : DIN Rail 35mm Mounting or screw mounting;
Instruction of Installation and Use
1. The product has adopted structure compliance with EN50022;
suitable for DIN rail mounting NS35/7.5, NS35/15. Installation
steps are as following (please reference to dimensional drawing):
Step 1: Immobilize one side of product‘s mounting trough to
the DIN mounting rail;
Step 2: Pull out the spring clasp;
Step 3: Place whole mounting trough to the DIN mounting rail
properly;
Step 4: Release spring clasp to make sure the installation.
2. The product has calibrated before out of factory. After correctly
wiring, it can be powered and used immediately. But for further
precise signal sampling, user need to warm-up the product for 3
minutes before use. The auxiliary power requires isolation
voltage≥2000VAC, DC current output ripple＜10mV.
3. Basic testing method for accuracy
(1)According to the terminal definition table to connect the
testing circuit;
(2) The testing must to be done by under the following
conditions；
Auxiliary power: 24V±1％, ripple≤5mV
Ambient temperature: 25℃±2℃
Relative humidity: RH(45～75)％
Accuracy for Signal Power Source instrument: 0.05

Transducer
Power supply
JK1
4
3
1
JK2
+
-
2
V2
Sign
al
4
6
+
-
V1
GND
+E -E
(3) warming up the transducer for 3 minutes
(4) using output monitoring meter V1 to measuring the output
of signal power source instrument, set a any input value
which is within the measuring range of the transducer Ur.
(for e.g. if input value is 100V, the output is 5V, the
expected output value Ug should be calculated as:
Ug = 5V×Ur/100V
(5) using output monitoring meter V2 to measuring the output
voltage U0of the transducer, the basic introduced errorγof
the transducer should be calculated as:
γ= （Uo－Ug）/5V×100
(6) Repeating (4) (5), if calculated absolute value is less than
the given accuracy value of the transducer, it shows the
transducer’s accurate grade is qualified.
Caution:
1. Pay attention to the auxiliary power information, especially the
auxiliary power grade, and polarity, other wise will damage the
product.
2. pay attention to the wire connection; wrong terminal connection
will cause malfunction of the product and even damage the
product;
3. Don’t dismantle the product, and carry with care to avoiding
Mianyang Weibo Electronic Co., Ltd
No.7 Road second part of Xianren Road, Youxian District, Mianyang City, Sichuan province P.R. China
Tel: [phone] Fax: [phone]
www.wb-my.com [e-mail]

Mianyang Weibo Electronic Co., Ltd
No.7 Road second part of Xianren Road, Youxian District, Mianyang City, Sichuan province P.R. China
Tel: [phone] Fax: [phone]
www.wb-my.com [e-mail]
bump and fall of the product;
4. If the product has been using under the environment with strong
magnetic field interference, please pay attention to the shield of
input wire, and the output signal wire should be as short as
possible. For product intensive installation, the space between
each product should not be smaller than 10mm.
5. Only use identified terminals.
6. There is no lightening strike prevention circuit design in this
product. For out door and hazardous environment using, please
add protective alternatives.
7. This product uses fire prevent ABS crust, its temperature
withstand is only limited as +85 , higher than this limitation℃
will cause the product deformation. Please use and store
carefully.