HOW TO LISTEN TO AN AUDIO FILE OR RADIO
STATION
Your streamer is now ready to function and is connected to the
network. To stream your music files to the WM-10 you need to
use iTunes.
If you have not already installed it, download the software from
the Apple website (www.apple.com/en/itunes).
Now, launch the iTunes application. Once you have opened it,
select the loudspeakers on which you wish to listen to your
music. Usually, the choice-list can be found in the bottom right-
hand corner of the iTunes window. Select WM10_XXXXXX,
(where X represents the serial number of your Airdream
terminal).
And that’s all there is to it, you are now ready to listen to music.
Select the audio file you wish to play, then just sit back and
listen!
If you are already connected to internet via your home network
(see following paragraph), you can also add radio streams to
your play-list. Click on Advanced > Open stream and add the
address to the URL field.
iPhone OR iTouch REMOTE CONTROL
If you have an iPhone or an iTouch, they can both be used as a
remote control.
To do this, you must first download the Remote free application
from the App Store.
On your iPhone or iTouch, in the Settings menu, set up the Wi-
Fi connection using the AIRDREAM network and the password
“airdream “. Then select “Add Library“ and follow the
instructions on the screen. Once synchronized, your iPod or
iTouch displays the contents of iTunes.
CONNECTION TO THE HOME WI-FI NETWORK
If you have a wireless home internet access via a “box”, you
can also connect your WM-10 to that network.
This enables you to listen to internet radio stations on your hi-fi
system and continue to surf on the internet and listen to your
music at the same time.
To do this, follow the reset procedure detailed below, followed
by the specific configuration procedure for your network. To find
out more about configuration, please consult the specific
instruction sheet available on the Micromega website:
www.micromega-hifi.com.
RESET
If you wish to rename your network or connect to an existing
network, or if you are having any problems, you MUST reset
your WM-10. This is not a trivial procedure and we advise you
to do this only when it is absolutely necessary.
Before starting, check the serial number: WM10_XXXXXX and
write it down. This is even more important if you have several
wireless peripherals.
With the device switched on, using the tip of a pen or a paper
clip, press the Reset button for a few seconds (it is situated on
the rear panel) until the LED is flashing rapidly in Red. This
indicates that the reset is complete and you can now
reconfigure the device. To do so, consult the specific instruction
sheet available on the Micromega website: www.micromega-
hifi.com.
FREQUENTLY ASKED QUESTIONS
My computer doesn’t detect AIRDREAM. What
should I do?
Ensure that the LED on the WM-10 is blue and is not flashing. If
this is not the case, switch the device off then switch it back on
again. Wait until the setup procedure is complete (this may take
a few minutes).
Ensure that the Wi-Fi connection with your computer is active
and that no other peripheral device is connected to your WM-
10. Open the list of available networks and the AIRDREAM
network should appear.
An error message is displayed when I play a track on
iTunes.
Check that your firewall authorizes connections between your
computer and the WM-10 (for example if the Windows firewall is
activated, ensure that the box entitled “Don’t authorize
exceptions” is not checked). Pay special attention to the
settings of your antivirus software too.
Ensure that you have installed the latest version of the iTunes
software.
In some cases an update of the WM-10 firmware may also be
necessary.
My internet connection is suddenly interrupted for no
apparent reason.
Check that no other network is interfering with the connection.
Do not place the device close to any potential source of
interference and set the AIRDREAM network as your preferred
network.
Most of the time, interruptions are not caused by the WM10 but
depends on the place WM10 and your computer are installed.
For instance, in a building with metallic structure, the WiFi
connection can be troubled.
The LED on the WM-10 is flashing slowly in red.
The setup procedure has failed. You must complete the setup
procedure. To find out how to do so, consult the specific
instruction sheet available on the Micromega website:
www.micromega-hifi.com.
