MicroNet SP920MA-8 User manual

6
P/N 2300-0554
Quick Installation Guide
Model No.: SP920MA-12
Web: www.micronet.com.tw
Omni-Directional Antenna,
12dBi (N-Type Connector)
FCC Statement
This device compiles with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operation.
Warning!
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a
commercial environment. This equipment generates and can
radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference
to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at its own
expense.
7
Line of Sight (LOS) Principle
The RF signals will be attenuated as they pass through
object such as wall and building. The level of signal
attenuated is difficult to determine since the nature of the
wall, building is complex. In order to have good
connection with less attenuation, the Line of Sight
principle is required. It means that there is no obstacle
between antennas so that people in one wireless station
could see the other wireless station.
Free Space Path Loss
The following table list is the typical free space path loss
values in 2.4GHz. It's important that path loss increases
by a factor of approximately 6dB for every doubling of
path distance. To double the useable path distance, the
antenna or system gain has to increase by a factor of
6dB.
Distance
Loss (dB)
100 meters
80.23
200 meters
86.25
500 meters
94.21
1,000 meters
100.23
2,000 meters
106.25
5,000 meters
114.21
Specification
10,000 meters
120.23
5
MODEL
2.4~2.5GHz
SP920MA-8
Frequency
Gain
V.S.W.R
Impedance
Power Handling
Polarity
E-Plane
H-Plane
Connector Type
Mount Type
8dBi
SP920MA-12
12dBi
1.5 Max
50 ohm
10 Watts 20 Watts
Vertical
14 14
360 360
N Jack N Jack
Mast

4
3
1 2
Tube-End Mounting
Components: Staple, Hexangular Screw, Spring Washer, Fix
Mount and Antenna.
Step 1. Determine the position to set the antenna.
Step 2. Set the staple through the fix mount from the opposite side
(Picture 1).
Step 3. Set the hexangular screw and spring washer with the
staple and fix mount (Picture 2).
Components:
Step 2.
Step 3.
Wall Mount
Components: Peg, Setscrew, Fix Mount and Antenna.
Step 1. Determine the position to set the antenna.
Step 2. Drill holes to set fix mount with antenna by peg (Picture 1).
Step 3. Set setscrew for the fix mount with antenna on the even
surface (Picture 2).Step 3.
Installation
Before you start installing the antenna, please verify the following
items are in the package.
x 4
x 4
x 4
x 4
x 2
x 1
x 1
Introduction
Thank you for purchasing Micronet SP920MA-12 Omni-Directional
antenna. This quick installation guide is aimed at easy installation
procedures of this device. Before installation, please read the
following procedures carefully. Micronet SP920MA-12 is directional
antenna for data transmission that used to link two wireless
networks at 2.4 GHz ISM band (Industrial, Scientific and Medical).
SP920MA-12 is designed for outdoor use to extend wireless
connection coverage. It produces a gain of 12dBi and can be used
to extend the distance of Wireless LAN.
Package Contents
Please verify the following items are in the package:
1 x SP920MA-12 Omni-Directional Antenna
1 x Quick Installation Guide
1 x Mounting Kit
1 x Antenna Cable
Note: Contact your dealer immediately if any of the above items
are missing, damaged, or if the unit does not work.
Picture 1. Picture 2. Picture 3.
Staple
Spring
washer
Hexangular
screw
Picture 1. Picture 2. Picture 3.
Peg
Setscrew