MicroVision MV-2400li3 User manual

QUICK START GUIDE
MV-2400li3
Consumer LiDAR
Starter Kit

CAUTIONS & WARNINGS
All users of the Starter Kit must read this safety information before
operating the unit.
Warnings regarding use and care of the Starter Kit:
This MicroVision Consumer LiDAR Starter Kit is designed to be used in
conjunction with a MicroVision Consumer LiDAR Explorer Edition* which
is sold separately.
In a system where a Starter Kit is mated with an Explorer Edition, the use
of external optics or controls, adjustments of performance other than those
specified in this Quick Start Guide or User Guide may result in hazardous
laser radiation exposure.
* The MicroVision Consumer LiDAR Explorer Edition is a Class 1 device that conforms to
the IEC 60825-1:2014 Edition 3. Additional information regarding the laser classification
can be found in the documentation related to the Explorer Edition device.

SERVICE & MAINTENANCE
THERE ARE NO OPERATOR SERVICEABLE PARTS
INSIDE THE STARTER KIT
For preventative maintenance or repair of performance-related issues, the
system must be returned to MicroVision. See the Warranty accompanying
in this Quick Start Guide for contact information to initiate a return.

MV-2400li3
CONSUMER LIDAR STARTER KIT
The MicroVision Consumer LiDAR Starter Kit facilitates the evaluation of
the Consumer LiDAR Explorer Edition hardware and for host device application
software development. It is delivered ready to assemble into a working LiDAR
system. It is not intended to represent a consumer-ready end product.
Finished form factor, industrial design, thermal management, power
management, user interface, auxiliary features and any other commercial
product considerations should be addressed as part of bringing a product to
market to suit target audiences and differentiation requirements.

IN THE BOX
• Base plate
• Data conversion board
• Three M2 x 8 mm long Phillips flat head screws
• Two M2 x 16 mm long Phillips pan head screws
• Fan assembly
• Two M2.5 x 8 mm long Phillips pan head screws
• 5V DC power supply (not shown above)
• USB Type-C to USB 3.x Type-A Male 2 m cable (not shown above)
• #0 Phillips screwdriver (not shown above)
• Quick Start Guide (this booklet)

DIRECTIONS
1. Attach the Explorer Edition (sold separately) to the base plate
• Place the Explorer Edition
4
on top of the base plate
1
and run the three M2 x 8 mm long
Phillips flat head screws
5
in through the bottom of the base plate using the supplied
#0 Phillips screwdriver
8
; tighten the screws in place. NOTE: The base plate can be
tripod mounted using the 1/4”-20 threaded hole. It can also be mounted to a flat surface,
using M6 (¼”) fasteners, on 50 mm (2”) center-to-center spacing threaded holes.
2. Attach the data conversion board
• Orient the data conversion board
6
on top of the Explorer Edition. Once the data
conversion board is oriented and aligned, push down to connect the two boards.
As seen in the rendering on the following page, the barrel jack for the 5V DC power
supply is at the top right (J2), the USB-C jack at the top left (J5).
• Insert the two M2 x 16 mm long Phillips pan head screws
7
into the two available holes
of the data conversion board and tighten in place. NOTE: Two of the mounting holes will be
blocked by screws holding the lower two boards in place.
3. Attach the fan assembly (optional but recommended for widest operating environment)
• Attach the fan bracket assembly
2
to the side of the base plate with two M2.5 x 8 mm
long Phillips pan head screws
3
.
• Connect the 2-wire fan cable to the keyed connector
9
.
This completes the assembly of the Starter Kit components
with the Explorer Edition (sold separately).

3
2
1
58
7
6
4
9

POWERING ON
1. Plug the 5V DC power supply into an 110V-220V AC outlet and connect the barrel plug
from the 5V DC power supply to the power jack
1
on the Starter Kit data conversion
board.
2. Plug the USB cable Type-A end into a PC and the USB-C end into the jack
2
on the data
conversion board.
3. Turn on the power by pressing the power button
3
.
4. Refer to online documentation for next steps. (See next section)
1
2
3

SOFTWARE AND APPLICATIONS
Visit https://github.com/MicroVision-Inc/Consumer-LiDAR/ for Visualization
Software, Software Development Kit, User Guide and Example Applications.
Consult the bar code label on the box for your specific model.
SERVICE AND SUPPORT
For questions and support please contact MicroVision Customer Service by
Engineering and development support are not included with the purchase
of the MV-2400li3. For expanded support services beyond basic
troubleshooting, please contact your MicroVision sales representative.

NOTICE AND LIMITED WARRANTY
STARTER KIT IMPORTANT NOTICE
The enclosed Starter Kit is a “Prototype” intended for use for ENGINEERING DEVELOPMENT OR
EVALUATION PURPOSES ONLY and is not considered by MicroVision, Inc. to be fit for commercial
use. As a Prototype, this device may not meet the technical requirements of the European
Union directive on electromagnetic compatibility.
The user assumes all responsibility and liability for proper and safe handling of the unit. Also be
aware that the enclosed unit may not be regulatory compliant or agency certified (such as FCC,
UL, CE, etc.) with the exception of IEC 60825-1 Laser Safety. MicroVision assumes no liability for
application assistance, customer’s product design, or software performance.
Subject to the terms of the MicroVision End User License Agreement found in the downloadable
User Guide at http://github.com/microvision-inc. MicroVision grants Customer a limited, non-
transferable, non-exclusive license to use MicroVision software and firmware in connection with
the use of the Prototypes. MicroVision is not selling any MicroVision software or firmware to
Customer. Customer is not licensed to use MicroVision software or firmware in connection with any
other application or for any purpose other than evaluation of the Prototype.
Contact Information. If you have any questions, please contact MicroVision Customer Service by
Limited Warranty. MicroVision warrants that the Prototype will be free of defects in material and
workmanship for ninety (90) days from the delivery date. MicroVision will at its option, repair or
replace the Prototype or refund the purchase price paid by Customer for the defective Prototype.
The repaired or replaced parts or Prototype may include new, reconditioned or re-manufactured
parts and equipment at MicroVision’s option. Such repair, replacement or refund shall be the
sole remedy of Customer in the event of MicroVision’s breach of this limited warranty. All costs
associated with shipment to MicroVision for warranty service, including but not limited to freight,

duties, insurance and customs fees are Customer’s responsibility. MicroVision will pay the freight
costs associated with the return shipment to Customer. Duties, insurance, customs and any oth-
er fee are Customer’s responsibility. The method of shipment will be at MicroVision’s discretion.
Repair or replacement of any parts or equipment does not extend the period of warranty. If a
component MicroVision bought from a third party fails and the component is still covered by a
warranty from a third party, MicroVision will take reasonable action to pass that warranty on to
customer. THIS LIMITED WARRANTY IS MICROVISION’S ONLY WARRANTY. MICROVISION
EXPLICITLY DISCLAIMS ANY AND ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, THE WARRANTIES OF MERCHANTABILITY, FITNESS
FOR A PARTICULAR PURPOSE, AND INFRINGEMENT.
The warranty considerations by MicroVision set-forth above do not cover, and MicroVision
will have no obligations hereunder if any non-conformance is caused in whole or in part by
(a) accident, transportation, neglect, misuse, exposure to extreme temperatures or excessive dust or
moisture, alteration, modification or enhancement of the Prototype(s), (b) incorporation, interfacing,
attachment of any feature, program, or device to the Prototype(s) by a person or entity other
than MicroVision, (c) use of the Prototype(s) for other than the specific purpose for which the
Prototype(s) are designed or (d) any use of the Prototype(s) not in accordance with a guide or user
manual. MicroVision does not warrant that the Prototype or associated software will run error free
or without interruptions or will operate with third party applications. MicroVision is not liable for
loss of data or down time. MicroVision is not responsible for resolving software issues caused by
Customer Components or third party software.
LIMITATION OF LIABILLITY. IN NO EVENT WILL MICROVISION BE LIABLE TO CUSTOMER
FOR ANY LOST PROFITS, LOST OPPORTUNITIES, OR ANY OTHER INCIDENTAL OR
CONSEQUENTIAL DAMAGES, REGARDLESS OF THE FORM OF ACTION, BASIS OF THAT
CLAIM, OR THE THEORY UNDER WHICH THE CLAIM IS PRESENTED, EVEN IF THAT PARTY
HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT WILL
MICROVISION BE LIABLE TO CUSTOMER FOR ANY DAMAGE OR LOSS IN EXCESS OF THE
TOTAL PURCHASE PRICE PAID FOR THE PROTOTYPE(S). IN NO EVENT WILL MICROVISION
BE LIABLE FOR ANY CLAIM AGAINST IT BY ANY THIRD PARTY.

© 2019 MicroVision, Inc. All rights reserved.
DB0140004
Table of contents
Popular Controllers manuals by other brands

Hispacold
Hispacold ECOMASTER COMFORT user manual

MICRO-EPSILON
MICRO-EPSILON MSC7401 operating instructions

Grundfos
Grundfos Vaccuperm VGA-146 Installation and operating instructions

Mitsubishi Electric
Mitsubishi Electric FX3G SERIES Quick start manual

Paragon
Paragon Sentry Xpress 2.0 instructions

Naturela
Naturela NPBC-V3C-1 Technical manual