ComAp L151006001 User manual

Connected heating solution
Connected head
Installation manual

2
• Read these instructions carefully before installation.
• Check that the thermostatic body of your radiator is
compatible with the heads:
> diameter: M28 or M30
> thread: 1.5 mm
• The 30 mm diameter adaptable heads are also
compatible with Danfoss RA thermostatic inserts and
bodies (adapter included in the universal pack).
• Handle the head with care.
• Keep good air circulation near the head.
• Do not cover the COMAP head.
Caution

app.
comapsmarthome.
com
3
Follow the installation
procedure online step by step
Visit the page
app.comapsmarthome.com
Download the COMAP Smart Home app
and start the installation of your product
Create your accout in the app

4
COMPATIBILITY
There are two types of radiator heads:
There are mainly, two standard types of connections of the head on the
thermostatic valve: M28 × 1.5 or M30 × 1.5 (corresponds to the diameter
and thread of the pipe in mm). Check the thermostatic valve on your
radiator before installation to see if it is compatible with the model you have
purchased.
The thermostatic heads
They are generally graduated from 1
to 5 and can be easily replaced by a
COMAP Smart Home head
The manual valves
If some of your radiators have manual
valves, we advise you to go through a
licensed installer to make your valve
compatible with the COMAP Smart
Home head.

5
Possible extensions
You can extend your installation and install up to 10 COMAP Smart Home heads (ref.
L150005001, L150006001, L150007001 depending on the thermostatic valve installed on
your radiator).
2 COMAP thermostatic heads
1 gateway
*according to the reference you purchased, see page 12
4 AA LR6 batteries 1 ethernet
cable
1 USB cable
2 M30/M28 adapters* 2 Danfoss adapters*
KIT CONTENT

6
INSTALLATION PRINCIPLE
The COMAP head can be mounted on each of your water radiators.
The gateway connects to the internet box.
The heads communicate with the gateway by radio waves (868MHz). The
maximum distance between the gateway and the heads depends on the structure
of your house (wall thickness, materials...) and the radio environment.
Description of the head
Gateway
Temperature
sensor
LED Display
Handwheel
to change the
setpoint
Piston
Mounting
nut
Head Head

7
DISPLAY OF THE HEAD
Pictogram Meaning Action
Starting of the head Wait a few seconds
Update of the head Wait for 1 to 2 minutes
Low battery level Remember to change the batteries
Critical battery level, the
heads doesn't control the
temperature anymore.
Change the batteries to recover the head
functionnalities
Communication problem
1. Disconnect and reconnect the internet box
gateway. The two lights on the gateway should be
green and steady.
2. If the gateway has both lights fixed aer the
restart and the head continues to display these
pictograms, contact customer service.
Radio range limit Your thermostatic head is at the limit of radio range, a
repeater may be necessary, contact customer service.
The calibration is
inconsistent
1. Remove the head from the radiator.
2. Remove the batteries for 30s and reinsert them.
3. Observe if the head piston makes a back and forth
movement.If Yes: Remove the batteries. - remount the
head. - Reinsert the batteries to restart the calibration.
- If the error persists, contact customer service.
If No: contact the customer service
The radiator valve has not
been detected during the
calibration.
1. Make sure that the head is properly installed on the
thermostatic body (Tightening, no clearance)
2. Restart the calibration by removing the batteries for
10s and putting them back in.
3. If the problem persists, contact customer service.
or
or
or

8
INSTALLATION
19.5
19.5
1. Download the COMAP application. Go to the App Store or Google Play to
download the "COMAP Smart Home" application.
2. Create your account on the application. Follow the steps to create an ac-
count on your COMAP Smart Home application
3. Connect the gateway to your internet box
The first light (power light) on the
gateway lights up.
The second light on the gateway
(communication light) lights up and flashes,
then becomes steady aer 1 to 2 minutes.

7. Step only necessary for the first head
installed: In the installation path of the
application or web interface, enter the
serial number of one of the heads. The
serial number is placed on the label on
the bottom of the head.
8. The other heads automatically appear in
the application as they communicate.
9. Once the heads are set up in the
application, proceed with the assembly
of the heads.
9
19.5
5. Place the heads within 40cm of
the gateway.
6. Turn the ring to wake up each
head next to the gateway.
4. Insert the batteries into the head
a. Slide the handwheel forward
b. Insert the batteries in the direction
indicated in the battery compartment.

Mounting the heads
12. Remove one battery of the head.
If your valve has a thread but
the head nut does not screw on
because it is too big, screw on the
adapter M30/M28 if you have a
universal kit.
11. If necessary, add an adapter
10. Remove the current head.
If your insert or thermostatic body
is of the Danfoss RA type: separate
the two plastic parts of the adapter.
Screw the Danfoss adapter
corresponding to your model onto
the radiator tube.
10