Middle Atlantic Products ESSEX SIDE Series User manual

Lock with Locking Clip
QTY DESCRIPTION
2
HARDWARE/ITEMS SUPPLIED
TOOLS REQUIRED
• #2 Phillips Screwdriver
SIDE-XX-XX
ESSEX LOCKING SIDE PANEL
Instruction Sheet
I-00702 Rev -
1) Engage side panels to mounting holes in rack as shown. (FIGURE A)
INSTALLATION
FIGURE A
Thank you for purchasing the Essex Side-XX-XX Locking Side Panel. Please read these
instructions thoroughly before installing this product.
THANK YOU

Page 2
LOCK INSTALLATION
1) Knock out lock hole. (FIGURE B)
2) Remove screw from lock body.
3) Insert lock body into side panel and remove
key in a vertical position. (FIGURE B)
4) Attach lock clip to lock body on inside of
side panel as shown. Tap into place to
secure lock clip. (FIGURE C)
Remove key with lock
in vertical position
FIGURE B
FIGURE D
5) Attach cam to lock body using supplied screw
and tighten. (FIGURE D)
NOTE: This is the locked position.
6) Install side panel with lock in the unlocked
position as shown. (FIGURE E)
Lock Clip
Lock Hole
FIGURE C
FIGURE E
Lock Body
Lock Body
Screw
Cam
Lock Body
(Unlocked Position)

WARRANTY
Middle Atlantic Products (the "Company") warrants the ESSEX LOCKING SIDE PANEL to be free from defects in material or workmanship
for the lifetime of the product.
The Company's entire liability to the purchaser, and the purchaser's (or any other party's) sole and exclusive remedy, under this warranty
shall be limited, at the Company's option, to either (a) return of and refund of the price paid for, or (b) repair or replacement at the
Company's factory of the products purchased, or any part or parts thereof, which the Company has determined to be defective after
inspection thereof at the Company's factory.
This warranty does not cover damage due to acts of God, accident, misuse, abuse or negligence by parties other than the Company, or
any modification or alteration of the products. In addition, this warranty does not cover damage due to improper handling, assembly,
installation or maintenance.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT
NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT SHALL THE COMPANY BE LIABLE FOR ANY
SPECIAL, INCIDENTAL, INDIRECT, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING, WITHOUT LIMITATION,
DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION OR ANY OTHER PECUNIARY LOSS) ARISING OUT OF
THE USE OF THE PRODUCTS PURCHASED, EVEN IF THE COMPANY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES. THE COMPANY'S LIABILITY TO THE PURCHASER (OR ANY OTHER PARTY) HEREUNDER, IF ANY, SHALL IN NO
EVENT EXCEED THE PURCHASE PRICE OF THE PRODUCTS PAID TO THE COMPANY.
Corporate Headquarters
Corporate Voice 973-839-1011 - Fax [phone] / International Voice [phone] - Fax [phone]
middleatlantic.com - [email protected]
Middle Atlantic Canada
Voice 613-836-2501 - Fax [phone] / middleatlantic.ca - [email protected]
Factory Distribution
USA: NJ - CA - IL Canada: ON - BC
At Middle Atlantic Products we are always listening. Your comments are welcome.
Middle Atlantic Products is an ISO 9001 and ISO 14001 Registered Company.
1) Attach bonding wire to bonding point using hardware kit PET-K-SIDE. (FIGURE F)
GROUNDING AND BONDING
Protective Earth Terminals (PET) are located in backpan of the wall rack. These terminals are marked with the symbol
Wall rack parts, center section and door, contain or are provided with bonding points for connection to the backpan / PET.
Protective earth and bonding connections shall be in accordance with Article 250 of the National Electric Code.
Bonding Point
FIGURE F
Page 3