Midea HC-683WEN(ESNY) User manual
USER MANUAL
MODEL: HC-683WEN(ESNY)
REFRIGERATOR
Side By Side
EN
www.midea.comversion:001
Please read the Manual carefully
before use.
The Manual shall be kept in good
custody for later reference
Warning
Warning:connect to potable water supply only.
Warning
r
j
-
r
r/
I
2
"
;
/
/
•Invariable keeping esh technology
•Deost pre-cold
•Aptitude deosting
•Gliding shelves, convenient using
Freezer and refrigerator's rack designed as gliding and stretching ,it's convenient to
stored.
•Human aptitude
•Nice dimension
Ultra-thin size;Ultra great volume; Reigerator compartment uses the upscale armored glass rack.
•CFC and no-ost design. Fasting eezing
•Automatic alarm of problem
•Reliable compressor with good quality
•Opening door alalrm, LED screen
ng wire.
Left
Before adjusting the height of the door, rotate the downward adjusting
nut clockwise (as shown in Figure I) for 2 circles with a wrench,
and loosen the downward adjusting nut. Rotate the upward adjusting nut
(as shown in Figure I) to adjust the height, and then tighten the downward
adjusting nut counterclockwise again.
1.When the door of refrigerating chamber is low:
Open the door, use the accompanying wrench to rotate the upward adjusting
nut counterclockwise according to the method as shown in Figure I, to move
it upward until it is parallel and level.
2.When the door of refrigerating chamber is high:
Open the door, use the accompanying wrench to rotate the upward adjusting
nut clockwise according to the method as shown in Figure I, to move it
downward, until it is parallel and level.
Reigerators transption and location
Transportion
Please don't inverted,squeezed, virbration refrigertor. when moving, the tilt
angle can't larger than 45 degree.
Location
Attention
Start using
5
Tips:
the temperature of surrounding
Reigerator compartment
Put the od which are short-term storage or to eat at any time in the
reigerator comparment.
Shelf adjustment
then turn the shelf in the direction(2) for 90° until it
Height adjustment and cleaning of rack
rack ,
rack
6
Refrigerator compartment
Recommendati ons of storage area r all kinds of od
@
0
<
i
r�
.-:_,"
"
14
s
"
J
'r'
iC'-�"
-
J
®
7
Freezer compartment
' "I
@ ;Tr *'�:,
-[ J •
/-
/
@
m, •
1'1, V
/ /
[
i •
@
{(',
�
grilles
Introduction of Function
A 7
FRZ.TEMP. REF.TEMP.
MODE LOCK/UNLOCK
HOLD 3S UNLOCK
B 1 2 3 4 D
1. Button operation
A.Freezer compartment temperature adjustment B.Mode Settings
C.Refrigerator compartment temperature adjustment D.Lock/Unlock
2.Display
I.Vocation mode 2.Quick-freezer mode 3.Quick-cold mode
4.Lock icon 5.Freezer compartment temperature
6.Refrigerator compartment temperature 7 .Close icon
3.Lock/Unlock
& .
The llowing functions must be in operation under the unlocked state
Press mode button (button B), you can choose running mode as the following.
Vocation +Quick-freezer+Quick-cold and freezer + Quick-cold +None
♦ I
4.Vacation mode
9
5.Rapid cooling mode
6.Quick-eeze mode
7.Reigerator compartment temperature settings
°°
8.Freezer room temperature settings
°
°
the set temperature of eezer changes, if set relevant nction mode
(e.g. quick-cold mode, quick-eezer mode,quick-cold and eezer mode,
vocation mode), the relevant nction mode should be quitted or canceled at once.
Announcements
1000w
10
Maintenance and care refrigerator
Deost the eezer
Cleaning
11
Replacement on lights in freezer and refrigerator,
and specication of lights
When Power failure
When discarding the refrigerator
Simple trouble analyzing and shooting
Please read the llowing contents carelly bere repair request
12
not working
not perctly cooling
too much noise
od be eezed
Ordrs
DISPOSAL
Correct Disposal of this product
-
13
Energy Saving Tips
·The appliance should be located in the coolest area of the room, away from heat producing
appliances or heating ducts, and out of the direct sunlight.
·Let hot foods cool to room temperature before placing in the appliance. Overloading the appliance
forces the compressor to run longer. Foods that freeze too slowly may lose quality, or spoil.
·Be sure to wrap foods properly, and wipe containers dry before placing them in the appliance. This
cuts down on frost build-up inside the appliance.
·Appliance storage bin should not be lined with aluminum foil, wax paper, or paper toweling. Liners
interfere with cold air circulation, making the appliance less efficient.
·Organize and label food to reduce door openings and extended searches. Remove as many items as
needed at one time, and close the door as soon as possible.
14
How to Use this Water Dispenser
Warning
1.Only purified and cold boiled water have access to this water dispenser, and the two kinds
must free from any impurity. Coke, apple juice and other soft drinks that contain Carbon dioxide
are forbidden.
2.It is not allowed to fill water when the water boxes is removed from the machine door.
3.Never fill more water than the maximum figure that indicated on the water box.
4.Check out whether the water box is on its foundation bed when you are not able to get water
normally as usual.
5.When you are trying to move the water box, be sure that there is no water in it.
6.You are not allowed to remove any element of the water valve.
7.When use the machine for the first time or it has been out of application for a long time, remove
and clean it up before you put it into application.
8.If water in this machine has been out of use for a long period, you had better to drain them out of
the dispenser and add pure water, and then it can be used as usual.
9.It is suggested that the product should be cleaned up every three to six months.
10.When you are cleaning this product, if cleaning solution is used, you had better put the water box
to its original position, and fill the water box, then you shall drain 5 to 6 cups of water, in case that
there is any rudimental dirt of water dispenser instruction after you used cleaning solution.
11.When you are opening or closing the door of the water dispenser, try to avoid overexerting in case
that water in the box move and overflows.
12.Do not touch the bottle frame above when adding water.
Instruction of water dispenser
Filling of drinking water:
Open the water box, put the watering cover and then you can add water:
Steel wire fence string
Renovate to fill water
Water box cover
Water box body
Seal ring
Water valve elements
Water shall be filled here
How to Get the Drinking Water
1.Push the water shank inward by the cup
2.When you put the hand shank inward, there will be some water outflows,
when the hand shank is in its original position, no water outflows.
How to Remove and Clean up the Water Dispenser
First Step: remove
1.Take out the elements of the water box
Stick to both sides of the water box elements with both of your hands,
and draw out the elements of the water box outwards through 45 above.
You can translate the water box (to the side of the user) and get the
elements when the elements are out of water valve elements (when you
move the box, be sure that there is no water in it.)
2.Take down the seal ring of the water box elements
3.Step to remove the elements of water valve
Use the screwdriver and make the edge directs to the water valve elements
and then insert it in the free place that highlights outskirt, rotates the
screwdriver clockwise or anticlockwise, with the screwdriver moving, when it
tops the penstock, extracts the water valve elements by hands at the direction
of above 45°(You can not remove the elements of water valve)
Step 2: Clean up
1.Remove the water box itself, and the water box cover, the seal ring and the
water valve elements
2.Clean up the elements of the water box with cold or warm water.
3.Wipe out the water with dry cloth
Notes:
1.If you clean the water dispenser by cleaning solution, you had better put the
box to its originally position, and drain 5 to 6 cups of water out, then you can
use it normally, in case that there is remaining dirt of application instruction.
Step 3: Installation
1.I ns ta lla ti on o f wa te r valve e le me nt s
Pu t th e gu ide p ro je ct in g platf or m di re ct ed to the g ui de g ro ov e, af te r th at , pu sh
it d ow ns ide w it h 45 ?s la ntly at f ul l ti lt , un til you h ea r a cr ac k
2.Installation of seal ring of the water box
Put the seal ring to the bottom of the water box, and be sure that the seal ring
is in place. Avoid that wrinkle seal ring or in wrong place.
3.The Installation of water box elements
To keep the hanging slot of the water box elements direct to the hangers on the
door liner. The seal ring at the bottom of the box shall directed to the entrance
of the water valve elements, insert it to the corresponding position along with
the 45°slantly
make yourself at home
Table of contents
Other Midea Refrigerator manuals
Midea
Midea COMBI Series User manual
Midea
Midea BMF No Frost Series User manual
Midea
Midea HD-332RWEN User manual
Midea
Midea MDRT385MTE46 User manual
Midea
Midea COMBI Series User manual
Midea
Midea MDRB521FIE Series User manual
Midea
Midea SBS Series User manual
Midea
Midea EM131A5C-BS User manual
Midea
Midea MDRB470MG Series User manual
Midea
Midea UR-BCD830WX-ST User manual
Midea
Midea HD-113FN Series User manual
Midea
Midea MRF29D3ABB User manual
Midea
Midea MDRB470MGD28 Series User manual
Midea
Midea MDRT580MTE Series User manual
Midea
Midea HS-121LN User manual
Midea
Midea TMF Series User manual
Midea
Midea MDRS619 Series User manual
Midea
Midea MDRT333FGF01 User manual
Midea
Midea COMPACT HS-57LN User manual
Midea
Midea MDRF692MIE User manual
