Miele PT 8331 G User manual

02.11 Mat. NR. 07 803 810 / 02
Installation plan
Tumble dryers
.
Installatieschema
Droogautomaat
PT 8331 G
PT 8333 G
PT 8335 G
PT 8337 G
nl - NL
en - GB

Mat. NR. 07 803 810 / 02
2
Lees beslist de gebruiks- en montagehandleiding voordat u uw
apparaat plaatst, installeert en in gebruik neemt.
Dat is veiliger voor uzelf en u voorkomt schade aan uw apparaat.
Technische wijzigingen voorbehouden
It is essential to read the operating and installation instructions before
installing, commissioning or using the machine.
This avoids the risk of accidents or damage.
All rights reserved

Installationsplan / Installation plan: PT 8331/8333/8335/8337
Datum / Date: 12.01.2011 Seite / Page: 8
Technical datasheet
Tumble dryer:
Heating:
PT 8331/8333/8335/8337
Gas (G)
Legend:
Abbreviations in bold type:
Connection required
en - GB
Abbreviations in circle with dashes:
Connection optional or required depending on model version
Optional extras:
UM
Miele plinth
UG 8350 box plinth
Height
mm
127
Width
mm
900
Depth
mm
868
BS
Concrete plinth
Quality and density of concrete must comply with load.
Concrete plinth must be firmly secured to floor!
Recommended height
mm
100
Minimum height
mm
50
Width min.
mm
900
Width:min.
mm
1100
Machine connections:
Electrical
connection
1. Standard voltage (as supplied)
V
1N AC 220 - 240
Frequency
Hz
50
Rated load
kW
0.8
Fuse rating
A
1 × 10
Connection cable, min. cross-section
mm²
3 × 1.5
Cable screw connector
M 20
Connection cable (to be ordered separately)
Electrical connection must comply with national regulations.
Connection using multi-pole wall socket in compliance with
IEC/EN 60309 and IEC/EN 60947 is recommended in order to
simplify electrical tests.
If machines are hard-wired, a multi-pole mains switch must be
provided on site.
A wall socket or mains isolator must be accessible after
installation.
Equipotential
bonding
Connection with male thread
mm
10 × 35
with washers and nut.
M
10
Accessories to be ordered separately
If necessary, equipotential bonding with good galvanic
contact must be provided in accordance with all appropriate
national and local regulations.

Installationsplan / Installation plan: PT 8331/8333/8335/8337
Datum / Date: 12.01.2011 Seite / Page: 9
Gas connection
Nominal heat rating
kW
18
Machine-side connection according to ISO 7-1
Inch
½“
Length of connection hose (supplied)
mm
350
Stopcock to be provided on site.
Use of gas plug connection is not permissible on account of
restricted flow volume with respect to heater rating.
Natural gas
Connection thread (on site) schwanken)
Inch
½" internal thread
Connection pressure according to DIN EN 437
cf. operating and installation instructions
Liquid gas
Connection thread (on site) schwanken)
Inch
½" internal thread
or alternatively:
On-site connection with high-precision steel pipe
according to DIN 2391/DIN2393, with smooth pipe end,
DN
12
Min. connection length
mm
40
Connection sleeve ½" × ⅜" and ⅜" threaded union × DN
12 for steel pipe supplied with machine. ⅜" × DN 12 threaded union for steel pipe.
Connection pressure according to DIN EN 437
cf. operating and installation instructions
Connection to gas supply must comply with national
regulations.
Note installation instructions for gas-heated Miele tumble
dryers.
Waste air/gas
Max. nominal air flow in vented mode (PT 8337 only)
m³/h
580
Nominal air flow (PT 8331/8333/8335 only)
m³/h
480
Max. permissible pressure loss
Pa
200
Connection on machine side (ext. diameter)
mm
150
Connection pipe provided on site (int. diameter)
mm
150
Max. temperature
°C
80
This tumble dryer is a gas-burning machine without a flow-
operated safety device with fan downstream of heat
exchanger.
Technical design: B22 (as standard)
Waste gas pipework must be pressure-tight.
Waste gas connections should be performed in accordance
with national and local regulations and may require approval.
Note installation instructions for gas-heated Miele tumble
dryers.
As relative humidity inside the vent ducting can be as high as
100%, suitable measures must be taken to prevent a
backflow of condensate into the machine.
Air intake
Standard connection: Air intake from installation site
Unobstructed air intake into room recommended
(corresponding to 3 times the vent cross-section of
machine)
cm²
531
A sufficient supply of fresh air should be ensured to
replace the air extracted.
Alternative connection: Ducted air intake (from outside
building)
Connector on machine (int. diameter)
mm
161
Connection pipe provided on site (ext. diameter)
mm
160
Lid removal exposes live components! For safety reasons,
the pipe connected for central air intake should be at least
900 mm long and secured using two screws.

Installationsplan / Installation plan: PT 8331/8333/8335/8337
Datum / Date: 12.01.2011 Seite / Page: 10
Fittings (supplied)
Without plinth
2 × clamps
2 × screws DIN 571 (Ø × length)
mm
6 × 40
2 × rawl plugs (Ø × length)
mm
10 × 50
Machine must be bolted to the floor!
Fixing materials for a floating screed floor are to be provided
on site.
On concrete platform
2 × clamps
2 × screws DIN 571 (Ø × length)
mm
6 × 40
2 × rawl plugs (Ø × length)
mm
10 × 50
Machine must be bolted to the floor!
Fixing materials for a floating screed floor are to be provided
on site.
Machine data
Unit width
mm
906
Machine depth
mm
1035
Unit height
mm
1400
Casing width
mm
900
Casing depth
mm
930
Minimum width of delivery access to installation site
mm
920
Recommended rear wall gap (measured to front of machine)
mm
1500
Min. wall gap (to rear edge of lid)
mm
500
Net weight
kg
168
Dynamic floor load, max.
N
1890
Average heat dissipation
(dependent on ambient room temperature and programme
selected)
W
610
A Noise level
dB (A)
67.6
A Sound pressure level
(measured at a distance of 1 m from the machine and at a
height of 1.6 m)1 m
dB (A)
55
Installation should only be carried out by authorised fitters in accordance with valid regulations!
Observe installation instructions when installing machine! All rights reserved! Measurements in mm.